Search Documents

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By T. D. Murphy, G. V. Henderson

The element silicon, with its usual partner, oxygen, plays the same role relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO2) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO4 tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide Si02 (analogous to its congener carbon in CO and CO2); a tetrachloride SiCI4 (analogous to CC14); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117° to 200ºC but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures --such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert et al., 1973; Pecora, 1960). Pursuing its esthetic aspects, briefly, silica is well-represented among gem stones which, to qualify as such, must have the attributes of beauty, durability, and rarity (Jahns, 1983). As quartzose gems usually have but one or, at

Jan 1, 1983

By M. Kaufman, A. E. Palty

THE mechanical properties of an alloy under given test conditions are in the main determined by the grain size and the phases present, their distribution and temperature-time dependence. Alloys intended for use at elevated temperatures, especially multiphase alloys depending upon precipitation reactions for strengthening, are particularly susceptible to changes in the phases present. Unfortunately, for modern superalloys, very little published information exists which relates the mechanical properties to the basic structural variables. The present work is an effort to do this for an alloy widely used in aircraft gas turbines and related applications, Udimet 500.* The mechanical properties inves- two heats is within the normal specifications for the alloy. However, the elements which most strongly influence the phase reactions, C, Ti, Al, and Mo, are comparable in the two heats. There was no intentional addition of boron, but normal pickup is about 0.002 pct. The vacuum-melted material was received in the form of centerless ground wrought bar stock % in. diam. PHASE STUDIES A) Methods—Two methods were used to determine the phases present: X-ray diffraction measurements on electrolytically digested residues, and microscopic examination. No single commonly used electrolyte will reveal all the phases that may be present; therefore, two complementary acids were selected: HCl and H3PO4. The necessity for this will be shown below in the results. The acid concentrations used were 10 pct HC1 in alcohol and 10 pct H3 PO4 in water. The current density was maintained below 0.1 amp per sq in. Residues were rinsed and separated by centrifuga-tion. X-ray diffraction patterns were obtained in a 114 mm Debye-Scherrer type camera using cobalt radiation. A temperature of 2250°F was selected to obtain as complete solutioning of phases as possible without encountering incipient melting. Specimens were

Jan 1, 1961

By G. L. Simard, D. J. Salley, J. Chupak

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By J. Chupak, D. J. Salley, G. L. Simard

DITHIOPHOSPHATES and xanthates are the principal collectors for sulphide minerals, and consequently any knowledge of mineral-collector systems of this type is of value. In the present investigation an attempt was made to obtain information on the interaction of a typical dithiophosphate with galena. In carrying out this study, radioiso-topes, so much discussed in the past few years,', ' were extensively employed. By using radioactive dithiophosphate synthesized from radioactive phosphorus, a rapid and sensitive analytical procedure G. L. SIMARD is in the Research Division, Stamford Research Labs., American Cyanamid Co., Stamford, Conn.; J. CHUPAK, formerly in the Research Division, Stamford Research Labs., is now at Camp Detrick, Frederick, Md.; and D. J. SALLEY is in the Research Division, Stamford Research Labs. AlME New York Meeting, Feb. 1950. TP 2815 B. Discussion (2 copies) may be sent to Transactions AlME before April 30, 1950. Manuscript received Oct. 17, 1949. was at hand. This permitted determination of such important quantities as the rate of uptake of dithiophosphate by the mineral, the amount existing at equilibrium on the mineral surface and in the solution, and the desorption of the agent from the surface. Such measurements were possible even on single crystals of galena. In addition the exchange of dithiophosphate between the solution and the sorbed phase was examined, a matter which could be accomplished only by the use of isotopes. It is desired to point out at this time that throughout this paper the term "sorption" has been employed to designate the uptake of agent by mineral, without implication as to the nature of the process by which the uptake was accomplished. Experimental Materials: Galena: The galena was from the Tri-State district. For studies on ground mineral four preparations were used during the course of the investigation. These were prepared from selected large crystals by wet grinding in order to reduce surface oxidation. Alcohol was chosen as a convenient medium for this purpose. The ground mineral was then fractionated by sedimentation in alcohol, dried by evacuation, and stored in a nitrogen-filled desiccator. Data on the preparations are tabulated in table I. The size analysis indicated that the areas of the preparations were of comparable magnitude, even though the absolute values may be somewhat incorrect. Dithiophosphates: Nonradioactive dithiophbsphate (di-isopropyl or di-secondary butyl) was obtained by purification of a commercial product. An aqueous acid solution of the agent was extracted with petroleum ether, the ether layer dried, and the dithiophosphate precipitated as ammonium salt with anhydrous ammonia. Several repetitions of this process resulted in a nearly colorless, flaky product of good purity. (General formula (RO,)PSSNH,). Radioactive dithiophosphate was synthesized by heating radioactive elementary red phosphorus* • For early experiments (1943 to 1944), the elementary red phosphorus was obtained from the cyclotron group at the Crocker Radiation Laboratory of the University of California. Berkeley, through the courtesy of Dr. Joseph W. Hamilton. For more recent work (1946 to 1949). the elementary radioactive Phosphorus has been supplied by the Oak Ridge National Labarotories on allocation from the U. S. Atomic Energy Commission. with sulphur at 270" to 300°C to produce radioactive P,S,. The latter was then treated with the desired purified alcohol (isopropyl or secondary butyl) at 60" to 80°C to form the dithiophosphoric acid derivative. Purification was effected in the same manner as for the nonradioactive material. The effectiveness of the purification method was established by the isotopic dilution method." The same technique was used to show that only negligible decomposition of neutral or of carbonate solutions of the dithiophosphate took place over a period of a day; this was true whether or not galena was suspended in the solutions. Procedures: Radioactivity: The activity of a solution was obtained by counting with a small glass-jacketed, silvered Geiger counter, using a conventional scaling circuit.' Crystals and other solids were counted under a bell-shaped, mica-window counter tube. Sufficient counts were made so that the probable error of counting was of the order of +I-3 pct. The specific activity in terms of counts per minute

Jan 1, 1951

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By Thomas V. Falkie

4.3-1. Introduction. DEFINITION OF PRODUCTION SYSTEMS ENGINEERING. Surface mines, like most other mining and manufacturing operations, are usually organized along functional departmental lines. Frequently a mine manager will have his responsibilities divided among production, maintenance, administrative, and engineering functions. Often these are separate departments, but various combinations and variations of these functions can be found in mining companies throughout the world. The production function is responsible for physically removing the ore from the ground, processing it, and shipping the product to its market. The production manager supervises and is responsible for all man-machine systems necessary to extract and process the ore. The maintenance function, which is sometimes included within the framework of production, has the task of insuring the maximum availability and longevity of equipment needed to produce the ore. The administrative function is responsible for accounting, personnel, industrial relations, purchasing, public relations, property, and other related staff functions. For purposes of this chapter, engineering can be described as the function which plans, designs, and supervises construction of physical plant and equipment. In this context engineering includes mechanical, civil, chemical, electrical, and mining engineering. However, another phase of engineering is to prepare plans to insure that the various man-machine components function in an optimum way towards the single most important goal of any enterprise-the maximization of return on the investors&apos; money. Along with the planning, another duty of engineering is to audit all phases of the operation for the purpose of recommending improvements toward this same general goal. These latter two ideas form the basis for a discussion of production engineering and systems engineering. Production engineering is a catchall, problem-oriented function whose duties can include: 1) solution of day-to-day production problems, 2) short-

Jan 1, 1968

By Jim D. Mote, Eugenia M. Howard, Willis L. Barmore, John E. Dorn

The effect of stress and temperature on the creep rate of Ag-33 at. pct A1 and Ag-33 at. pct Al-1 at. pct Zn for prismatic slip was determined over a range of temperatures from 440º to 700°K. The alloys exhibited a brief initial inverted transient creep over which the creep rate increased slightly to a steady-state value which depended only on the stress and temperature, regardless of the previous strain history. The steady-state creep rates were found to be given by: where the activation energy is independent of the stress and strain and agrees fairly well with that estimated for diffusion. The observed creep behavior was shown to be in qualitative agreement with a model based on the stress-induced local disordering in the vicinity of a dislocation. OVER the past fifteen years, considerable progress has been made in correlating the experimen-entally observed plastic behavior of pure metals over each temperature range with one or more of a series of theoretical strain-rate controlling dislocation mechanisms. Despite the current interest in the plastic behavior of intermediate phases and inter metallic compounds, however, very little has been done in identifying the operative dislocation mechanisms in these materials. It is anticipated that the plastic behavior of intermediate phases can be rationalized in terms of the same dislocation mechanisms that are appropriate to pure metals and a solid solutions, provided the additional complexities arising from crystal structure, bonding, long-range order, short-range order, and defect lattices are taken into account. As part of a more extensive investigation on the plastic behavior of intermediate phases, Mote, Tanaka, and Dorn1 recently reported on the effect of temperature on the yield strength for prismatic slip in the hexagonal Ag-33 at. pct A1 intermediate phase as recorded in Fig. 1: Over Region I the deformation was observed to take place as a result of the thermally-activated Peierls mechanism, and over Region II the athermal disordering mechanism applied. The experimental data at that time, however, were not sufficiently extensive to identify the thermally activated mechanisms operative over Region III. It is the purpose of this investigation to attempt to identify the mechanisms that are operative over this high-temperature region. It will be shown that the same mechanism operates all over Region Ill, although the activation energy for this mechanism is in good agreement with that for diffusion, the process cannot be attributed either to the motion of jogged screw dislocations or the climb of edge dislocations. The results, however, are in good qualitative agreement with stress-induced disordering localized at dislocations. EXPERIMENTAL PROCEDURE The alloys studied in this investigation were prepared from silver, aluminum, and zinc (each of purity greater than 99.995 pet) by induction melting under an argon atmosphere and chill casting in a copper mold. Rectangular bar single crystal specimens (1/4 by 1/8 in. in cross-sect ion) of Ag-33 at. pct Al were grown in vacuum by a modified Bridgman technique. Similar Ag-33 at. pct Zn specimens were produced by an identical technique employing an argon atmosphere. The specimens were so oriented that the angle 90-Xo between the tensile axis and the normal to the prismatic plane and the angle A, between the tensile axis and the slip direction were 45 ± 1 deg. The effect of a change in temperature on the creep rate and a change in stress on the creep rate were determined over the temperature range

Jan 1, 1963

By N. J. Grant, K. M. Zwilsky

A series of copper-alumina dispersion strengthened alloys were prepared using three different copper and two different alumina powder sizes. Improvements in strength of up to ten times that of pure copper were found in room-temperature as well as elevated-temperature stress-rupture tests. Conductivity values remained from 70 to 90 pct that of pure copper. The best alloys were based on the finest metal powder (1 p) and contained from 7.5 to 10-0 vol pet of 0.018 or 0,033 p alumina. DISPERSION strengthening of metals consists of strengthening a metal matrix by the addition of oxides or other refractory constituents, followed by strain hardening, in order to reinforce the base material and extend its temperature range of application. Since the discovery of SAP by lrmannl and Von zeerleder2 in 1949, many investigators have reported data obtained on a variety of metal-inert oxide alloys.3-7 The present work deals with the mechanical mixing of copper and alumina powders. While several techniques of introducing the second phase have been investigated to date, mechanical mixing so far has been recognized as the simplest, least expensive, and most universally applicable technique that can be used to obtain an ultrafine dispersion of inert particles. In the present case, the effects of changing the metal particle size, the oxide particle size and the volume percent of oxide were investigated. This work is an extension of a previous study.6 EXPERIMENTAL PROCEDURE The starting materials were three different grades of copper powder and two different alumina powders. The three metallic powders were -74 µ(- 200 mesh) electrolytic copper powder consisting of irregular equiaxed particles having a normal screen distribution and analyzing 99.5 pct Cu, and two powders having a 5-µ and 1-µ particle size, average, respectively. The latter powders were produced by the hydrogen reduction of purified sulfate solutions at elevated temperature and pressure and were furnished by the Sherritt Gordon Mines, Ltd. The alumina used was obtained from Godfrey L. Cabot Co., under the trade name of Alon C, one batch of powder having a particle size of 0.018 µ, the other a particle size of 0.033 µ. The crystal structure of these alumina powders was found to be cubic gamma. Each batch of powder was mixed in a Waring Blendor for a total of 15 min, followed by a low-temperature reduction in hydrogen and vacuum compacting in cylinders which were hydrostatically pressed at 35,000 psi to give a compact that could be handled conveniently. Six of the compacts were hydrogen sintered at 900°C while the remaining four were sintered at 1000°C. Subsequently, all compacts were hot extruded at 760°C with a reduction of area ratio of approximately 20 to 1. Evaluation of alloys included density and resistivity measurements, room-temperature tensile tests, stress-rupture tests at 450°C plus one other temperature per alloy, hardness tests, microstruc-tural examination, X-ray analysis of the dispersed phase after dissolving the metal phase, and oxidation studies on two of the alloys. A vacuum-melted, wrought copper rod was tested together with these alloys for comparison purposes. RESULTS Table I is a summary of the compositions, sintering temperatures, densities and conductivity values of the ten alloys prepared. All alumina additions are given in volume percent, and will be referred to as

Jan 1, 1962

By C Gunther

Ore deposits are commonly divided into two classes, syngenetic and epigenetic, according to whether the ore was deposited together with the enclosing rock or was introduced after its deposition or solidification. Epigenetic deposits, which are by far the more important class, owe their formation to the channels that permitted the ingress of their metals, and both classes are subject to great modification by post-mineral changes in the containing rocks. A discussion of the structural features of rocks, therefore, necessarily precedes any consideration of ore deposits or processes of ore deposition. The arrangement of sediments in parallel and approximately horizontal layers is called stratification, and is an original prop¬erty of sedimentary rocks. Successive strata of the same sedimentary bed commonly differ from each other in some minor characteristic, such as texture or color, which results in a bedded or stratified appearance. The subjection of a rock to pressure develops within it parallel planes of weakness, called cleavage planes, along which the rock breaks into relatively regular slabs or blocks; the direc¬tion of these cleavage planes, which bear no relation to stratifica¬tion, is determined by the direction of the pressure that produced them. Where there are more than one set of cleavage planes, one of them is likely to be more prominent than the others. In sedimentary rocks, the cleavage may coincide with the stratifica¬tion but more commonly cuts across it. Van Hise has defined cleavage as the "capacity present in some rocks to break in some directions more easily than in others." Cleavage, therefore, does not imply the existence of subdivisions, but rather the tendency to subdivide along certain planes.

Jan 1, 1932

By Lawrence A. Roe

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H2O. However, as an industrial commodity, talc rarely approaches theoretical purity. Nevertheless, the impure talc products of commerce find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are tremolite, chlorite, dolomite, mica, and magnesite. Steatite was originally a mineralogical name applied to pure talc. In today&apos;s commerce steatite generally refers to the massive variety of talc suitable for electrical insulator manufacture. Block steatite ore can be machined into various shapes. Impure varieties of massive or block talc are still commonly referred to as soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soapstone and talc, this is a natural thing since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as "slip") have been grouped together and called soapstone or talc. Further, there is a mineralogical relationship of pyrophyllite to montmorillonite and talc to hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Indians on Santa Catalina Island, Calif. In the mid-1800s, soapstone from deposits along the western foothills of the Sierra Nevada mountains was used by white settlers for building and ornamental stone and in the linings and foundations of furnaces (Anon. 1956). Previous to 1916, the annual recorded production in California did not exceed 2000 tons. In the period 1912 to 1918, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state&apos;s annual output of talc was in the range of 9,000 to 20,000 tons. In the mid-1930s, the use of talc in wall tile grew rapidly. In California, the production of talc grew to 63,000 tpy in 1943. The post-war building boom helped California production to grow to 120,000 tons in 1951. In 1968, production was 165,000 tons, 1969 was 145,000 tons, 1970 was 185,000 tons, and 1972 was 155,000 tons. Talc mining in New York state dates to about 1878 when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville, New York. In 1893, this operation was sold to the International Pulp Co. which changed its name to the International Talc Co. in 1944. Total production from seven New York mines, in 1948, was 130,000 tons. A new talc operation, the Gouverneur Talc Co. owned by the R.T. Vanderbilt Co., began operations near Balmat, N.Y., in 1948. The initial capacity of the processing plant was 200 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to over 600 tpd. The Vermont talc industry began just after the start of the 20th century. Talc was discovered in the area of the present Johnson, Vt., talc mine in 1902. The American Min¬erals Co. initiated plant operations at Johnson in 1904. The Magnesia Talc Co. opened a plant at Waterbury, Vt., in 1913 (Burmeister, 1963; Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine has a long history as a producer of talc crayons. The Eastern Magnesia Talc Co. was formed in 1924 by a merger of the Eastern Talc Co.

Jan 1, 1975

By R. A. Vandermeer, C. J. McHargue

The (001) fiber-texture component, found in aluminum rods extruded at subzero temperatures, consists of particles of various sizes having extremely irregular shapes dispersed in a nonuniform way throughout a matrix of the (111) orientation. Apparently the (001) texture component is not a result of recrystallization but rather is due to the presence of reimanents of the original grains which fragmented from the main body of material as it reoriented towards the (111) orientation during the extrusion process. Both X-ray line-broadening measurements and electron-microscopic observatwns indicate that, after extrusion, regions having (001) orientations are in a state of relatively less strain and distortion than (111) regions, suggesting that the former have undergone less plastic deformation. A (001) fiber-texture component is also found after complete recrystallization of extruded specimens. Approximately one third of the recrys-stallized volume has this orientation. The (001) fragments, formed during the extrusion process, act as nuclei for recrystallization; i.e., the pain boundaries separating these fragments from the matrix are capable of migrating during annealing. Electron-transmission microscopic observations and X-ray line-broadening measurements indicate that (001) regions recover at a much more rapid rate than (111) regions at annealing temperatures up to 187°C. DURING the extrusion of a rod or the drawing of a wire the individual grains comprising the piece tend to reorient towards a preferred orientation (texture) which is of the fiber type where a particular crys-tallographic direction, (uvw), in each crystallite tends to be aligned parallel to the longitudinal axis

Jan 1, 1964

By James M. Link

The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple compared to the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve the understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instances, more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test loops such as the one at the Colorado School of Mines Research Institute. The pilot scale projects are designed to provide the basic engineering data necessary to design slurry transport pipeline systems. Usually three slurry solid concentrations are pumped at various line velocities and optimum slurry densities and velocities are determined. Critical velocities, friction head losses, power requirements, and so forth, are also determined from measurements and calculations. Wear tests are also strongly recommended and anticipated pipe wear rates in inches per million tons of solids reported.

Jan 11, 1972

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.&apos; No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

By Harold Bloom, H. E. Hawkes

Streams and rivers are the principal channels into which the weathering products of rocks and their contained ores are funneled. The inorganic load of a stream system is a crude sample of all the earth materials in the drainage basin of the stream, and the heavy mineral assemblage of sediments is one of the oldest and most successful guides to certain kinds of bedrock ore in unexplored terrain. Early application of this method was made possible by the ease of separation and identification of heavy minerals in the field with the simplest equipment. Water analysis for traces of base metals became a practical possibility about eight years ago with the development of rapid chemical tests that could be carried out at the field site. Since that time the water method has been widely used in mineral reconnaissance, and a substantial number of discoveries have been reported. Here again, the techniques developed for this work were relatively simple and could be performed easily at the field site.

Nov 1, 1956

By H. S. Price, J. E. Warren

Techniques for studying the performance characteristics of heterogeneous reservoirs have been developed. The effect of permeability variation on both the steady-state and the transient flow of a single fluid has been investigated. Limited comparisons with field and laboratory data have been made. The physical models studied consist of random three-dimensional arrays of homogeneous porous blocks. The permeabilities of the individual elements are assigned according to a specific distribution function; uniform anisotropy is introduced by varying the relative dimensions of the blocks. A particular model is perturbed simply by re-arranging its elements at random. The behavior of a physical model is determined by digitally solving its numerical analogue. Based on computational experiments, subject to the restrictions implied by the assumptions that were made, the following general conclusions have been drawn. 1. The most probable behavior of a heterogeneous system approaches that of a homogeneous system with a permeability equal to the geometric mean of the individual permeabilities. 2. The effects of flow geometry and anisotropy on the most probable value of the effective permeability of a heterogeneous medium are finite but not significant. 3. The permeability determined from a pressure build-up curve lor a heterogeneous reservoir gives a reasonable value for the effective permeability of the drainage area. 4. A qualitative measure of the degree of heterogeneity and its spatial configuration are obtained from a comparative study of core analysis and pressure build-up data. It has been indicated that these conclusions are predicated on the assumption that the core analysis and the pressure build-up data represent true reservoir characteristics. Common sources of error in these data have been discussed. One of the most significant problems of reservoir engineering is that of determining the nature and the disposition of the heterogeneities that inevitably occur in petroliferous formations. It is with this problem that this paper is concerned. Extensive research, both theoretical and experimental, has provided reasonable descriptions of the physical processes that are associated with primary and secondaryrecovery mechanisms. Similar progress in the fie1d of numerical analysis and the evolution of truly high-speed digital computers have made it feasible to calculate the behavior of these mechanisms under almost any environmental conditions. It appears to be logical, then, to conclude that the mechanistic performance of any reservoir can be predicted with some confidence. Unfortunate1y, a necessary condition for the validity of this conclusion is that the formation be adequately described in a macroscopic sense. This condition cannot be satisfied ill general; therefore, a frustrating situation currently exists — it is possible to compute the effect of reservoir heterogeneity on behavior, but it is not possible to specify the heterogeneity itself. In many cases, the predicted behavior of a project is so completely dominated by irregularities in the formation&apos;s physical properties that the gratuitous assumptior, of a particular form for the variation can reduce the solution of the problem to a mere tautological exercise. While all porous media are microscopically heterogeneous, only macroscopic fluctuations need be considered since the fundamental concepts of reservoir mechanics are based on macroscopic quantities. For the simplest case in which only one physical property varies from point to point, the degree of heterogeneity that is apparent depends on three distinct factors, i.e., the nature of the property&apos;s variation (frequency distribution), its disposition (spatial distribution) and the inherent stability of the mechanism being studied. Consequently, any attempt to devise an unambiguous scale of heterogeneity must take these factors into account. Since this investigation is intended to be exploratory, it will be restricted to single-phase flow because of the simplification implied; both steady-state and unsteady-state behavior will be considered. Furthermore, to keep the number of parameters

By Roy A. Koski

INTRODUCTION Cleveland-Cliffs Iron Company, and its subsidiary companies, operate and manage mining, beneficiation, and pelletizing operations in the Upper Peninsula of Michigan, the province of Ontario, Canada, and the State of Western Australia, Australia. The concentrates and natural ores vary mineralogically, physically and chemically. This paper describes the techniques employed in pelletizing the various concentrates and ore fines. The plant operations described are the Republic, Humboldt, Tilden, Empire and Pioneer in Michigan, the Adams and Sherman in Ontario, and the Robe River in Western Australia. Table 1 contains further details regarding design and operating capacities, commissioning dates, and participant ownerships. Allis-Chalmers grate-kiln systems are utilized in Michigan and Ontario, and Dravo straight-grate systems in Western Australia. Currently, the Empire and Tilden operations are being expanded. At Empire the additional pelletizing unit, identified as Unit IV, will have a design capacity of 8 996 metric tonne/d and is scheduled for startup May 1, 1979. The Tilden operation is being doubled with the additional pelletizing unit, identified as Unit 11, having a de- sign capacity of 12 599 metric tonne/d. Startup is scheduled for January 1, 1980. MINERALOGY OF CONCENTRATES AND NATURAL ORES In the Upper Peninsula of Michigan, the operations process ores from the Negaunee iron formation of the Marquette Range. The

Jan 1, 1977

By D. L. Sikarskie, B. Paul

A theory is presented for the static penetration of a single rigid wedge into brittle material. The material considered is one which exhibits both crushing and chipping phases in the penetration process. If the wedge angle and three parameters are specified, the theory predicts forces and associated penetrations during both the crushing and chipping phases. For certain ranges of the parameters agreement with the limited experimental data available is promising, except for the initial phase of the penetration process where refinements on the proposed theory are required. The theory also predicts that for certain values of the wedge angle and other known parameters, the chipping process does not occur and penetration is due entirely to crushing. When viewed in detail, the drilling of rock by percussive means involves, among other things, system dynamics, actuating forces, dynamic stress levels and the actual penetration mechanism of the bit into rock. If rock drills are to be significantly improved, a thorough understanding of the entire system would be highly desirable. In this paper, one aspect of the system, namely the mechanism of penetration of the bit, will be studied in detail. It has been found1 that for the velocities encountered in percussive drilling (of the order of 20 fps) a static analysis adequately describes the penetration process, at least for some rocks. Hence, we will only be concerned with describing analytically the static penetration of a single wedge shaped tool. It will further be assumed that the wedge is long enough to permit a two-dimensional analysis. Numerous authors have studied the static penetration of a wedge into rock. The following papers give some of this work and provide additional references to other work. Cheatham2,3 has assumed the rock to behave plastically and has obtained force-penetration equations for both Coulomb-Mohr and parabolic yield criteria. Evans and Murrell4 have studied the penetration of two types of coal and have found equations relating the penetration characteristic (P/dSc) to wedge angle for the various strength coals tested. race&apos; attempted to find a correlation between hardness as determined by indenting the material and other mechanical properties and concluded that the results of such a test are generally inconclusive. His paper however contains a very extensive bibliography on the indenting of many different materials. Gnirk6 also has a fairly complete literature review on the static penetration of rock, of which he makes use in his indexing studies. A wide range of behavior is found in the wedge penetration of different rocks under different external conditions. For example, a rock that is essentially elastic-brittle at standard pressure may become elastic-plastic at a high confining pressure.7 It has also been observed4. " that some rocks will merely be crushed and indented by a wedge, whereas others will crack and form chips, furthermore the existence or non-existence of chips depends in great measure on the geometry of the indentor, type of rock and the depth of penetration. Hence, to attempt a theory which embraces all possible behavior is not practical at present. We, therefore, confine our attention to predicting the force-penetration characteristic and volume removal behavior for a type of rock which exhibits both crushing and chipping phases in the penetration process. Such behavior is characteristic of the harder rocks such as granites and represents a more difficult problem than the behavior of softer rocks such as coal and certain sandstones. In this preliminary study an attempt will be made to describe only the essential features of this complex penetration process. A qualitative description of these essential features is obtained with the aid of Fig. 1.1, where a wedge of vertex angle 28 is shown at some intermediate stage of the penetration process. As the wedge advances, the rock is fragmented (i.e. crushed) in some local region surrounding the wedge, the shape of this region being unknown. Simultaneous with the fragmentation in this local region, essentially elastic stresses are assumed to be building up in the surrounding rock. When a certain penetration level, di+1, is reached, the stresses along some surface are sufficient to cause failure and a chip is thus formed. The process now repeats, i.e., a crushing phase followed by the formation of a chip.

Jan 1, 1965

INTRODUCTION TO SAMPLING THEORY Before specifically discussing mineral sampling and sampling procedures, let us briefly consider broader and more universal concepts of modem sampling theory. A sample is de- fined as a representative part or a single item from a larger whole, being drawn for purpose of inspection or shown as evidence of quality. In modem theory the sample is a part of a statistical population whose properties are studied to gain information about the whole. The theory of sampling is built around the concept that if enough representative units of a larger overall population are selected without bias, the average value of the units will approximate that of the total population. Modem theory attempts to answer the question of how many samples are enough, given certain limits and constraints, and seeks to apply methods of sample selection and of estimation that provide, at the lowest possible cost, estimates that are precise enough for the purposes at issue. In order to meet these objectives the designer of a sample survey must rely heavily upon statistical theory. Statistics has been defined as the collection, presentation, analysis, and interpretation of numerical data. Statistical methods are primarily concerned with making valid inferences about a population based upon samples taken from the population. For most statistical applications, the total sample is in terms of number of items, attributes, or things; whereas mineral samples are usually in terms of weight or volume of mineral particles. Certain steps are involved in a well designed sample survey without regard to the particular field of application. Because the desired characteristics of an unmined mineral deposit can- not be known other than by sampling, we will consider these principle steps in terms of a mineral sample survey: 1) Clear definition of the objectives of the survey. In the case of mineral sampling this step is so apparent as to be almost ridiculous. However, it is surprising how often the overall objective of a sampling program is overlooked when decisions are made on a day-today basis. 2) Definition of the population to be sampled. The word population is used to designate the aggregate from which the sample is chosen. A sampling program may be designed to determine the grade of a single stope within a mine, the grade of a particular zone within a complex ore body, or the total value and extent of a mineral deposit. Since mineral sampling is usually done in phases, it is well to

Jan 1, 1980

By George M. Enos, Robert J. Anderson

An impoRtant factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2-mm. (equivalent focal length) apochro-matic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002 to 0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002 to 0.0004 mm. thick. This thickness is equivalent to 50,000-

Jan 1, 1925