Search Documents

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By A. M. Beebee

IN the present century the coal and manufactured gas industries have been eclipsed in public interest by oil, natural gas, and hydro- electric energy, which have had the benefit of rapid development and novelty. I sometimes wish that our social- order were such that hydro power had been developed first, that the use of gas from coal had never been seriously considered, and that our domestic energy requirements were supplied by other fuels. Sup- pose the manufacture of gas from coal should then come on the scene at the present time with the current plight of the railroads, coal regions, and labor generally, presenting the fact that it could increase the amount of coal mined and shipped by the railroads by some 16,000,000 tons, and increase the coal used at existing u plants five times. Imagine the great public interest that would be manifested; it would supply the cooking and water-heating requirements of a community with a superior character of service at a cost to the customer approximately half that which had obtained previously. Would not such a situation be heralded as the salvation of our country and all help be given it?

Jan 1, 1940

By D. R. Cook, W. M. Shepard, H. T. Morris

The East Tintic district in central Utah has produced ores of gold, silver, copper, lead, and zinc valued at more than $120,000,000. All of this ore has been produced from blind ore bodies in Paleozoic sedimentary rocks that are concealed beneath hydrothermally altered volcanic rocks and cut by intrusive bodies of Eocene age. The Paleozoic rocks, which range in age from Early Cambrian to Mississippian form the core and limbs of a large, northtrending asymmetric anticline that is cut by low-angle thrust faults, high-angle transcurrent faults, mineralized fissures and faults, and normal faults that are both older and younger than the mineralized fissures. The ore bodies generally may be grouped into two classes: ( 1) massive replacement bodies that are rich in silver, lead, zinc and manganese and (2) fissure veins that are valuable primarily for their content of gold, copper, and silver. The replacement ore bodies are localized chiefly in the Middle Limestone Member of the Ophir Formation of Middle Cambrian age where it has been thrust-faulted against older or younger rocks and cut by northeast-trending mineralized fissure zones. The fissure veins primarily are productive only in the Lower Cambrian Tintic Quartzite. Extensive lowgrade deposits of lead-zinc-silver ore recently have been discovered in Devonian carbonate rocks in the Lower plate of the East Tintic thrust fault but as yet are unevaluated. The principal guides to ore include: ( 1) intersections of northeast-trending fissures and crossbreaking faults that brecciate the carbonate rocks; (2) zones of late-stage pyritic, calcitic, and sericitic alteration in the lavas; ( 3) primary geochemical anomalies in the altered rocks; and ( 4) mineral zoning patterns of the known ore bodies. The present development of the Burgin mine would seem to assure the continued productivity of the district for at least a decade.

Jan 1, 1968

By K. A. Grange, W. S. Holt, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By Northcutt Ely, Charles F. Wheatley

This chapter deals with the systems of laws by which governments regulate the exploration for and production of the minerals within their jurisdictions. It is a summary, restricted by necessary space limitations, of material assembled by the author for a forthcoming publication of the United States Bureau of Mines, "Summary of Mining and Petroleum Laws of the World." (Information Circular, 1959.) The present study is organized in three parts, dealing with (1) the historical background of these legal systems, (2) laws of the United States, and (3) laws of other countries of the world. The reader's attention is invited to the acknowledgments at the end of the chapter, which inadequately express the appreciation due those who have assisted in the collection of this material. Part I. Historical Development of Major Western Systems of Land Tenancy with Respect to the Ownership and Control of Minerals The use of metals in primitive societies was largely confined to the manufacture of weapons for self-preservation. The ruler's control over copper, then brass, then iron, was essential to maintenance of his own ascendancy at home and his group's position against neighbors who had access to similar metals. Ancient societies were thus characterized by the ruling group's ownership of minerals and metals. The Egyptian civilization, which emerged in the fourth millenium B.C. upon the agricultural subjugation of the lower valley of the Nile, was responsible for extensive development of the upper valley as a source of mineral wealth. The production of gold during the height of that civilization has been estimated at $30,000,000 per year, thus equaling the early placers of California and Australia. The mines of Egypt were the property of the Pharaohs and were controlled at their direction. Greek mining developed a different scheme of land tenancy which more closely resembled modem concepts. Development of mineral resources was

Jan 1, 1959

Jan 1, 1968

Official Program

Jan 8, 1950

How Mining Engineers Will Fare in 1977 Mining Education- The State of the Discipline Coal Mining Technologists are a New Force in the Labor Pool Trained Manpower Provided by Mining Technology Programs Putting New Engineers to Work-A Management Perspective

Jan 1, 1977

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsa¬tions. The stratification usually is effected in a rectangular open¬top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (91) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through %-in. to 0, and mixed sizes of ores down to %3 O-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 percent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although con¬siderable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tenta¬tive conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way.

Jan 1, 1943

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By Elmer W. Pehrson

OPINION seems widely divergent as to where we stand with respect to future mineral supply. From some quarters we hear that the United States is about to become a "have-not" nation and about to experience the evil consequences such a situation would entail. Others claim that we are still a treasure house of stored-up mineral wealth, the surface of which barely has been scratched. The data to be presented here support the conclusion that neither of these viewpoints is correct and that we are far from exhaustion of those mineral resources that are basic to our industrial economy. However, exhaustion is well advanced in a number of important subsidiary minerals so that we can no longer drift along with the easy-going philosophy that the earth will provide. The time has come when we must recognize the true situation and do something about it.

Jan 1, 1945

By Dunbar D. Scott

The development in the perfection of mine-surveying instruments has been by no means rapid, as it has depended somewhat on the details of construction borrowed from astronomical and geodetic theodolites, largely on the restrictions laid down by mining companies and the prejudices of mine managers themselves, but more than all on the methods used in conducting surveys and the importance attached thereto. Mine-surveying, in some form or other, has been practiced from the very earliest times; but it has never kept pace with the other branches of surveying, or even with the art of mining itself, and cannot be recognized as an exact science until shortly before the beginning of this century. The works of Hero of Alexandria, who lived in the second century B.C., are still extant, and contain descriptions of a rectangular sighting-instrument, which he invented and called a diopter. His improvement upon this simple construction, which possibly he devised for use in the Greek mines for rough leveling-purposes and for laying out any angle, must be considered, says Hübner," as the origin of the highly perfected theodolite of to-day. Whether this instrument came into general use during the first centuries of the Christian era, is not recorded; in fact, no writer undertakes to tell how mine-surveying was conducted until 1556, in which year Agricola expounds the principles of mining and metallurgy in his De Re Metallica, devoting the entire fifth chapter to the practice of mine-surveying (see Fig. 1). In mediæval times those who possessed any knowledge of engineering skill made strenuous effort to keep their art a secret, partly on account of the miners' proverbial conservatism and partly for their own personal aggrandizement, and were, in

Jan 1, 1899

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By E. M. Norris

Phosphate deposits are distributed widely over the earth's surface. Of the known areas of deposit, eight fields are of particular interest because of their vast reserves of high grade phosphatic material and the volume of their production that goes to the world's great consuming areas. These fields, in the order of their present economic importance, are situated respectively in Florida, French Morocco, Kola Peninsula of U.S.S.R., Tunisia and Algeria, Tennessee, Montana-Idaho-Wyoming-Utah, Ocean and Naru Islands in the Gilbert group, and in Egypt. The Rocky Mountain deposits have a comparatively low ranking in the phosphate trade of today, but this field contains one of the largest known reserves of phosphatic material, associated with which are recoverable trace minerals, which are of increasing importance in our national economy. The first discoveries of phosphate rock in the western states were recorded in Cache1 and Rich2 counties in Utah, respectively in 1889 and 1897. Mining operations were begun on these deposits near Montpelier, Idaho, in 1906. During the latter year geological studies of the phosphate beds were started by Weeks and Ferrier of the U. S. Geological Survey. These studies have been continued to the present day by a distinguished roster of the Survey's technicians. As a result of this systematic exploratory program, the Survey has published a series of bulletins, papers, and maps, which provide the mining public with a comprehensive study of the exposed

Jan 1, 1949

By Oliver Bowles

STRIKING new developments in the field of industrial minerals include the employment of lime, salt, coal, and air for the manufacture of stockings, and the substitution of paper for granite and marble in making tombstones. Certain minerals that have heretofore been regarded as valueless except as museum or laboratory specimens, are now being applied commercially. Serpentine, in forms neither fibrous nor ornamental, massive topaz, pinite, and zoisite are examples. For certain other minerals, notably pyrophyllite, bentonite, vermiculite, and sulphur, extension of established uses into new fields has occurred. Substitution takes a toll in many industries, but producers of industrial minerals as a class have gained more than they have lost in recent years. Encouraging progress has been made in developing at long last a suitable substitute for certain of the uses of mica, the only industrial mineral on the strategic list of commodities established by the War. and Navy Munitions Board. Some of the more important developments in process, equipment, and use .that have come

Jan 1, 1940

By H. F. Moore

DURING the last six years, there have been many extensive investigations of the fatigue of metals. The major work of 'these investigations has been the determination of constants for fatigue strength of wrought ferrous metals; but during the past year or two there have become available considerable test data on the fatigue strength of certain nonrferrous metals, including copper, brass, bronze, nickel, copper-nickel alloys, aluminum and aluminum alloys, magnesium and magnesium alloys. It is not proposed to give here extensive quantitative tables of test results; for such tables, reference is made to the published data of various laboratories. The following general conclusions, however, seem to be fairly well established: 1. The phenomenon known as "fatigue" of metal really a progressive fracture of metals. A minute (probably submicroscopic) crack is formed in the metal, the internat stress, is intensified at the ends' of the crack, and under successive applications of load the crack spreads like a minute hacksaw cut until there is not enough sound metal left in the cross-section of the piece to stand the load. applied, and then failure occurs suddenly. 2. For wrought ferrous metals, there is .a limiting intensity of stress (as computed by the ordinary formulas of mechanics of materials) below which, a metal is able to withstand an indefinitely large number of repetitions of stress without failure. This limiting stress is known as the "endurance limit or the fatigue limit.? For reversed flexure, the endurance limit for. wrought ferrous metals is usually not far from 50 per cent. of the ultimate tensile strength.

Jan 1, 1925

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work' the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,' Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951