Search Documents

If world oil prices stabilize at $ll/bbl, if the US decides on the "accelerated supply" case for domestic fuel resources, if investment capital is available, if environmentalists' demand become reasonable, if land withdrawals are halted, if government grants generous depletion allowances and fast depreciation write-offs, and if many other "iffy" conditions are met-then shale oil production may reach the 1-million-bpd level by 1985, according to the Project Independence Report. In the "base case" scenario, oil shale production would be, at best, about 250,000 bpd at $11 prices, and "much lower if expectations for $7 oil prices prevail." In this regard, the FEA study reflects the conclusion reached by companies engaged in oil shale development work. Thus, except for some new technological breakthrough in mining, the birth and growth of the US oil shale industry will occur only if oil prices stabilize at about $ll/bbl.

Jan 5, 1975

By E. M. Furness, A. S. Henderson

ORIGINALLY the Babbitt experimental plant grinding circuit consisted of one rod mill 101/2 ft diam by 12 ft long in open circuit followed by two ball mills 101/2 ft diam* 12 ft long in parallel cir- the slow-speed ball mills. The next step was to improve rod mill operation by changing the speed of this mill. Such an attack would affect only one mill and would allow slower speed on the ball mills. The rod mill, as originally purchased, operated at 15.45 rpm. Additional pinions were purchased to test this mill at 16.45, 17.45, and 18.45 rpm. When the mill speed was increased by the use of these pinions, rod breakage with this short mill increased out of all proportion to the improved grinding, until at 18.45 rpm breakage became as high as 7 lb per

Jan 1, 1958

By Otto C. Kopp, Thomas B. Crattie, Dennis R. Owen

Whole-rock analyses of limestones, fine-gralned dolostones and coarser-grained dolostones adjacent to mineralized breccias (Coy mine, Mascot-Jefferson City district) were compared with similar lithologies adjacent to apparently non-mineralized breccias at the new Thorn Hill section located approximately 39 km north of the Coy mine. Specimens were analyzed for Ca, Mg, Si, Al, K, Fe, Mn, Sr, Br, C1, S, Ti and P using X-ray fluorescence analysis. The concentrations of the major and most minor elements for Thorn Hill specimens fall within the range of concentrations for Coy mine specimens; however, significant differences (probability < 0.05) were noted for Fe, C1 and Br for fine-grained dolostones and for MgO, Fe and Mn for the coarser-grained dolostones. No significant differences were detected for the limestones.

Jan 1, 1985

By A. U. Seybolt

DURING the course of an investigation of hot corrosion of nickel-base superalloys (combination oxidation-sulfidation attack at high temperature), it was considered possible that sulfur might gain entrance to the alloy in part, at least, by diffusion through the scale. Cr203 is nearly always observed as a prominent component of the oxide scale, and hence some experiments were carried out to examine the tracer diffusion of sulfur through Cr203 at 1000° C in the upper temperature range experienced by jet engine blades and vanes. Some hot-pressed Cr203 discs of quite high density were available from an earlier investigation1 on the rate of crf3 migration through Cr203. The Cr203 was 99.3 pct pure and contained -0.06 pct Fe as the largest metallic impurity. Additional data is given in Ref. 1. In this earlier work it was found that the rate of cation diffusion was independent of the atmosphere of thermal equilibration when using nitrogen, argon, or air, and also that the electrical conductivity of the hot-pressed Cr203 compacts was likewise independent of atmosphere in this range, thus indicating that the de-

Jan 1, 1969

By Frederick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production Co., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenandoah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1-An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2-Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3-Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1952

By V. F. Hollister

The South American porphyry copper province includes most of the Andean orogen, excepting the tin province of Bolivia. Porphyry coppers have not been commonly found within the tin belt, though copper-tin deposits in San Rafael, Peru and copper-tungsten deposits in Llamuco, Chile, are known. James" shows the depth to the Moho to appreciably thicken where the tin belt exists, but disclaims any genetic significance from this coincidence. Table I gives some of the most important porphyry copper deposits explored to date, but does not include Antaminas, Peru, nor a number of other large skarn deposits associated with intrusions. V. D. Perry* points out that porphyry copper mineralization does occur to some extent in the intrusion associated with many of these skarn deposits. Also not included are the suspected possible porphyry type occurrences, such as, for example, quartz-sericitically altered lower levels of the Casapalca mine, Peru. Many deposits not well enough documented to list in a summary paper are also excluded. Should anyone care to tabulate all other large copper de- posits in South America, they could demonstrate that a tremendous potential awaits the proper political and economic climate in the future.

Jan 8, 1973

By J. D. Price, W. M. Bertholf

THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers.

Jan 12, 1954

By G. F. Comstock

These notes should be considered as a further discussion of Mr. S. W. Miller&apos;s paper on "Some Structures in Steel Fusion Welds."l In that paper and the resulting discussion, several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8-in. (9.5-mm.) steel plate, about 21/4 by 13/4 in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extended through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what Mr. Miller called cem-entite and Mr. Jeffries martensite, while Mr. Ruder and Professor Boyls-ton think that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Pig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1920

By Donald K. Weaver

Eight different oil zones have been identified and produced at Santa Fe Springs, of which three or four are in turn divided into two or three parts. These zones, from top to bottom, are the Foix, Bell, Meyer, Nordstrom, Buckbee, O&apos;Connell, Clark and Hathaway, or third Clark. While there has been some difference of opinion over this nomenclature with reference to the different zones referred to as Clark, it has no particular bearing on the water problems. Each of these oil zones has had waters of varying salinity associated with it, either within or at the bottom of the zone. Table 1 is a tabulation of the zones, their maximum thicknesses, salinity and heads of various waters. Surface waters are fresh, and of high head, giving artesian flow in some instances.

Jan 1, 1931

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller&apos;s paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

By A. R. Rule, D. C. Dahlin, D. E. Kirby

The US Bureau of Mines is currently engaged in research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate, as part of a government effort to assure an adequate supply of fertilizer minerals. Western phosphate varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current methods of beneficiation (normally restricted to sizing), the USBM has developed a flotation procedure that includes depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Tested on several different ore types, the procedure has yielded phosphate concentrates that range in grade from 28 to 31% P2O3 with a phosphate recovery factor of 60 to 70%.

Jan 1, 1978

By Clinton H. Crane

DR. TILNEY, the great expert on the study of the development of the brain of human beings and animals, tells us that the greatest difference between the human brain and the brain of animals is that man alone has shown evidence of being able to predict the future. Just why he throws overboard the busy bee who lays up honey for the winter, the squirrel who gathers nuts, and the humble ant, I do not know. At any rate, it is nice to be assured by an authority that we have this power of prophecy. My own experience with attempting to prophesy the future has convinced me that our only possibility of being good prophets is to be good students of history.

Jan 1, 1940

Jan 1, 1937

By R. H. Thorpe

Longwall working in Britain developed to overcome problems arising from depth of seams causing roof and ventilation difficulties. This system became very widespread particularly in the thicker seams, where faces of up to one mile in length were not uncommon. In the thinner sections, in order to remain competitive, the longwall undercutting machine was developed. Following the development of the coal cutter, every other aspect of the face operation was examined and mechanized as it became a bottleneck to output and efficiency. The face system itself was modified and workings concentrated with the same objectives.

Jan 1, 1977

By AIME AIME

EARLE EDWARD SCHUMACHER, the new Chairman of the Institute of Metal, Division. is well known to the metallurgical profession. His election a, Chairman is the culmination of fifteen years&apos; service to the Institute, beginning in 1930 when he was elected Member. Since that time he has served as member of the I.M.D. Data Sheet Committee. 1935-40; Papers and Publication Committee. 1936; Executive Committee. 1937-1910: Papers and Programs Committee, 1937-1938. (Vice-Chairman, 1939-40, Chairman. 1941-12): Annual Award Committee. 194142. (Vice-Chairman, 19431: Vice-Chairman, LM.D., 1943-44; Chairman Publication Committee, 1943-44; member Powder Metallurgy Committee), 1944. Pew other men have contributed so Much time anti effort in so many way- to the interests of the metals branch o4 the A.I.M.E.

Jan 1, 1945

By S. O. Reichert

The nuclear industry has made a considerable effort to reduce environmental pollution with the result that knowledge in the field of radioactive waste management is well advanced. An example of the methods used for radioactive waste disposal is provided by the Savannah River Plant (SRP) operated by E. I. du Pont de Nemours & Co. for the AEC. It occupies an area of 320 sq mi along the Savannah River downstream from Augusta Ga., and has production facilities that include a fuel preparation area, three reactor areas, two chemical separation areas (F and H), and a heavy water plant. Gaseous, Liquid and Solid Radioactive Wastes Are Handled During Disposal The primary sources of radioactive waste are the reactor and chemical separation facilities. The reactors are cooled and moderated by heavy water which, in turn, is cooled by river water in heat exchangers. This arrangement prevents irradiation of the river water so that radioactivity is not discharged into the river water except when small quantities of moderator are lost by heat exchanger leaks. Because of the high cost of heavy water, these losses must be kept to a minimum.

Jan 9, 1968

President Howe : It is not so clear to me that the facts which Dr. Waldo brings forward really argue that the nature of the combination between copper and aluminum differs from that of the combination between copper and zinc or copper and tin. As regards electric conductivity, I suppose that the fact, which he thinks points to a special intimate kind of union between aluminum and copper, is that the line in his Fig. 1 is neither straight nor uniformly curved, but that its curvature varies rapidly, not to say abruptly. But we find just such variation in like curves for the copper-zinc and copper-tin alloys. Thus, a slight addition of zinc or tin to copper causes a change in color wholly out of proportion to the quantity added; and, as we add zinc or tin to copper, the tenacity rises very greatly, only to fall off abruptly with further additions of either of these metals. Dr. Waldo : My curve related only to electrical conductivity. The President : If irregularity in one physical property argues

Jan 1, 1895

Jan 1, 1927

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period May 10 to June 10: Rene de Sallier, New York, N. Y. Karl Koelle, San Luis Potosi, Mexico. H. S. Chamberlain, Chattanooga, Tenn. W. A. Wilson, Salt Lake City, Utah. F. R. Pretyman, Oyster Bay, N. Y. P. E. Barbour, Candor, N. C. R. Eustice, South Australia. R. C. Blanchard, London, England. F. C. Darby, South Australia. S. K. Tong, Shanghai, China. Grant H. Tod, Livermore, Cal. W. T. Burns, Great Falls, Mont. J. Murray Clark, Toronto, Canada. F. W. Bacorn, Butte, Mont. J. H. Adams, Birmingham, Ala. H. B. Pulsifer, Chicago, 111. A. Faison Dixon, Encontrador, Venezuela. Dwight E. Woodbridge, Duluth, Minn. C. W. Merrill, San Francisco, Cal. Heinrich Ries, Ithaca, N. Y. Francis Church Lincoln, Boston, Mass. H. L. Slosson, San Francisco, Cal. Frank R. Corwin has severed his connection with the Arizona Copper Co., Clifton, Ariz., and is now shift superintendent at the smelting plant of the Copper Queen Consolidated Mining Co.. Douglas. Ariz.

Jan 7, 1914

By G. E. Karantzavelos

A novel two-stage froth flotation process for the recovery of pure magnesite from low grade ores is described. The process consists of a first-stage, magnesite flotation step where a rougher magnesite concentrate is floated with amine collectors. The first-stage froth concentrate is then repulped in fresh water, and quartenary ammonium salt and fuel oil are added to float the remaining impurities. The results from laboratory batch tests show that a high-grade magnesite concentrate assaying 0.99-0.20% Si02 and 2.84-0.46%a Ca0 can be produced. Regulation of the variables controlling magnesite froth flotation also allows the variation of the ratio % Ca0: % SiO2, between the acceptable limits 0.32 to 5.79. This ratio is important to the quality of dead-burned magnesite.

Jan 1, 1985