Search Documents

T.P. 1958 D. H. DAVIS.*-Mr. Carris has ably pre¬sented the problems of coal preparation, particularly those brought about as the result of increased mechanical loading. Many mines are now crushing the run-of¬-mine raw coal through 12 or 15 in. immediately after it is dumped from the mine car and before it is handled by conveyors. At certain mines the removal of large slate mechanically has been solved by the installation of scalping screens consisting of bars or rails set at spacing of 12 to 15 in. on the top deck of the main raw-coal sizing screen. At the plants where these are in use, the plus 12 or I5-in. raw material contains 60 per cent or more free rock or slate, so that it is easier to pick coal than to pick rock. After the screening at 12 or 15 in. is accomplished, the oversize material is diverted to one side of the shaker, where a picker allows the refuse to pass off the shaker into a chute and guides the coal back onto the shaker. After the large rock has been removed, it is then advisable to reduce the size of rock by crushing before putting it onto a conveyor. A great saving in picking labor has been made by the use of such scalping screens, which in addition has maintained the plant capacity when handling a dirtier feed. The great increase in percentage of coal under 1/4 or 3/8 in., coupled with a greatly increased percentage of free impurities in this size, is the most serious problem that has been brought about by mechaniced loading. Many plants that formerly prepared good quality 1/4-in. to o or 3/8-in. to 0 slack by air¬cleaning are faced with installing facilities for wet-cleaning mechanical and heat-drying and water clarification. The change to wet prepa¬ration of fines usually affects the marketing problems for many coal companies. There will also be problems involving wastage of fine solids and stream pollution. Much work will be necessary for improvements in present practice. Pneumatic and electrostatic methods for cleaning fine coal should receive consider¬able attention in an attempt to avoid wet¬cleaning of fines. The preparation supervisor and the plant personnel should not be satisfied merely to run the cleaning-plant machinery and assume that the job will be done for them. Coal is a heterogeneous substance and in many instances is constantly changing. This is more true when full-seam methods are in use. Only persons trained to observe closely and make the necessary changes in plant operation will be able to solve the many problems that will be imposed on the preparation plants. The plants will require skillful and observant operating men. With full-seam mining methods, seams of roof coal will often be mined. Under the former mining systems these strata were not mined and frequently they contain a high per¬centage of bony and banded partings. The mining of this coal will greatly alter the washability and specific gravity characteristics of the feed to the plant. Often the percentage of 1.40 to 1.60 sp. gr. increased from 3.5 to 7.5 per cent, or nearly a 1.0 per cent increase in the ash content of the 1.60 sp. gr. float coal. Thus the cleaning problem is much more difficult, and it is unlikely the same ash content of cleaned coal can be produced as before without a decrease in recovery or the produc¬tion of a "middlings" product. Mr. Carris had this in mind when he said "The quality of the

Jan 1, 1946

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami's reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."' A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. ' J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957

By L. Grånäs, B. Aronsson

In a recent study of Fe-Si alloys Walter and Koch' observed pairs of dislocations in Fe-6.25 pct Si crystals rolled to reductions of 10 pct and subsequently annealed for 1 hr at 650°C. They interpreted these pairs as being due to stacking faults. From the spacing of the dislocations a stacking-fault energy of 15 to 19 ergs per sq cm was calculated. These authors did not pay any attention to the order -disorder phenomena in Fe-Si alloys. It is the purpose of this communication to report some preliminary results from a study of ordering and its influence on the plastic deformation of Fe-6.0 pct Si alloys. Our results suggest that the dislocation pairs observed by Walter and Koch may have been due to long-range order rather than to stacking faults. The alloys used in this investigation were prepared from pure electrolytic iron and silicon and were melted in argon. After hot working, strip tensile specimens were machined to a gage length of 70 mm and a thickness of 1 mm. The specimens were heat- treated for 2 hr at 1000°C, furnace-cooled, and subsequently deformed 2 pct in tension at 400°C. The strain rate was 5.6 X lo-' sec-'. Thin foils of the deformed specimens were prepared by means of the Bollman technique and examined in a Siemens Elmis-kop I at an accelerating voltage of 100 kv. In the Fe-Si system long-range ordering occurs at a silicon content of about 6 pct Si. In our alloys evidence for ordering is given by selected-area diffraction patterns which show extra reflections consistent with a super lattice of the D0 9 type. In addition, the dislocation arrangement in deformed specimens indicates that long-range order is present. A typical mi-crophotograph of a thin foil is shown in Fig. l. The dislocations are usually straight and parallel and laying in distinct directions. In the commonly observed (111) zone the projections of the dislocations are close to (113) and (oil). Observation of the image position indicates that the two dislocations in a pair have the same Burgers vector and hence constitute a superlattice dislocation.~ According to theory3 a superlattice dislocation in the DO3 structure consists of four ordinary dislocations connected by two types of antiphase boundaries as shown in Fig. 2. In our specimens only two dislocations in each pair have been observed, Fig. 1. The problem is to decide whether the area between these is a NN or a NNN antiphase boundary. Dark-field images using the (200) reflexion (the indices are defined with respect to the DO3-type superlattice) can

Jan 1, 1968

By H. E. Stauss

THE time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at 1100°C. better than did 10 per cent iridium- platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at 1100°C. Platinum alloys in their service at high temperatures encounter conditions some- what similar to those that exist in the usual form of the time-to-fracture "l test with steel. This paper is intended primarily to present results obtained by a "time-to- fracture" test under conditions approximating actual service for platinum (at the temperature 1100°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with lo per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., 1000°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,4 using as heating unit a small, horizontal, platinum- wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life-that is, the time-to-fracture-was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fracture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking stresses drop very rapidly to a small frac-

Jan 1, 1943

cation received from Brigadicr General Thos. G. Hanson said: "It is my painful duty to communicate to you the fact of the loss of your son, Martin F. Bowles. About 11 o'clock on the night of September 3, Lieutenant Bowles, with Lieutenant Joseph B. Keckler, 355th Infantry, in command of a reconnoitering patrol of our troops, encountered the enemy. In the ensuing engagement your son received a rifle bullet through his heart. His death was instantaneous and painless. His remains were intcrred with full military honors on the 4th of September." He was promoted to First Lieutenant, but his commission did not reach him before his death. He was president of the Missouri Mining Association, Missouri School of Mines, for the year 1916-17.

Jan 1, 1920

cation received from Brigadicr General Thos. G. Hanson said: "It is my painful duty to communicate to you the fact of the loss of your son, Martin F Bowles. About 11 o'clock on the night of September 3, Lieutenant Bowles, with Lieutenant Joseph B. Keckler, 355th Infantry, in command of a reconnoitering patrol of our troops, encountered the enemy. In the ensuing engagement your son received a rifle bullet through his heart. His death was instantaneous and painless. His remains were intcrred with full military honors on the 4th of September." He was promoted to First Lieutenant, but his commission did not reach him before his death. He was president of the Missouri Mining Association, Missouri School of Mines, for the year 1916-17.

Jan 1, 1920

• As part of $850,000 granted by the House Appropriations Committee for development of manganese in the U.S., the Bureau of Mines will build a pilot plant at Artillery Peak, Ariz., for development of low grade manganese ores. • The historic Argo tunnel and mill in Idaho Springs, Colo., will reopen shortly for the mining of uranium. The Uranium Co. of America has acquired control of the tunnel and mill and 12 nearby mining properties. J. H. Rodgers and G. C. Ridland will manage the operation. •The opening of a new 4000-ton per day coal mine in Washington Co., Pa., and the reopening of another mine of the same capacity in Fayette Co. has been announced by the H. C. Frick Coke Co. They'll help meet added war demands. •A 7000 bbl per day commercial synthetic liquid fuel plant, making gasoline from natural gas at Brownsville, Texas is being operated by the Carthage Hydro-col Corp., a Texaco subsidiary. The gasoline is produced by the Hydrocol process, chemically similar to the Fischer Tropsch process, but differing mechanically in several ways. To operate the process it has been necessary to build an oxygen plant producing 95 pct pure oxygen in quantities equal to U. S. production of commercial oxygen in 1946. •Over 96 pct of the class of 1950 at Montana School of Mines are now employed,, in industry, and they're scattered from MIT to the island of Cuba., • Cobalt, heretofore almost entirely imported, will soon be produced in Idaho. The Calera Mining Co. is building a 600-ton mill in which a cobalt and copper concentrate will be obtained from Idaho ores. •Plans for mining iron ore on the Conarky Peninsula in French Guinea, (an ECA project) call for equipment purchases as follows: 8 wagon drills, electric shovel for mining, conveyor for the port, 8 trucks, wrecker, 2 tractors, as well as miscellaneous accessories and spare parts. •A low-grade lead-zinc mineralization, located east of any known ore bodies in Utah's East Tintic district, has been located by a 2000-ft wildcat USGS drill hole. * Higher-than-going rates have been authorized by the Munitions Board for its stockpile program, where domestic production of scarce materials is low or uneconomical. Payment in excess of 25 pct over the foreign price is now permitted. •A new self-centering conveyor roll, developed by Carnegie-Illinois Steel, is expected to revolutionize materials handling. It completely eliminates the necessity for sideguides to keep materials on a conveyor. See P. 1028. •Great Britain's socialized coal industry employs twice as many miners, but produces less than half as much coal as America's coal industry. last year, British mines produced 28 million fewer tons of coal than the output of the same ,mines in 1939. Absenteeism amounted to a big 12 pot of working time. • Labor market conditions have tightened on almost a country-wide scale. Only 4 out of 143 major labor market areas have a substantial surplus -- less than half the total for May. Growing scarcities of skilled labor are in evidence.

Jan 10, 1950

By Peter Joralemon

Peter Joralemon's contention that Nevada contains one of the world's major gold belts is the result of 30 years' active involvement with the state's regional geology. He first suggested the possibility of an arsenical gold belt-tenuously based on two replacement deposits 480 km (300 miles) apart-in his 1949 doctoral thesis of the Getchell mine. In the years that followed, some 18 or 20 arsenical gold ore bodies have been discovered along the lineament Joralemon postulated. In this article, he uses the evidence that he's collected over the last three decades to refine his 1949 thesis. Joralemon's conclusion: A mineral belt containing a billion dollars worth of gold extends the length of Nevada, and a number of ore bodies are yet to be discovered.

Jan 7, 1978

By D. L., Hayes

THE concentration of zinc ore in Wisconsin is a comparatively simple process, although it presents problems that must be overcome in an efficient manner in such a way that installation and operating costs are low. As the ore deposits are small, the first cost of the concentrating plant must be low; while the low margin of profit makes it necessary to have the minimum operating costs. The original mills were copied from those of the Joplin district, as most of them were built and operated by Joplin millmen. These served the purpose well; they made a clean concentrate, which was the chief requirement at that time, as most 'of the mines were' considerably 'richer than the average at the present time, and wages and supplies were also considerably lower. ' The apparatus used at present has changed very little in principle. . The grizzly opening has gradually been increased to 12 in. and sometimes no grizzly 'is used. The crusher, gradually grew in size, the largest crusher has -an opening of about 24 by 13 in. and a 7/8-in. throw on the. eccentric shaft.

Jan 1, 1921

By PERCY E. BARBOUR

TWO YEARS after its organization, the Institute issued its first volume of TRANSACTIONS, covering activities that began in May, 1871, and continued through February, 1873. The preface of this first volume reads: The present volume contains the rules of the Institute, a list of members and associates, an abstract of the proceedings of the-first two years, and a number of papers selected from those proceedings. There is, therefore, nothing new in it. The papers have all been published, according to the custom of the Institute, in the Engineering and Mining Journal, and many of them have been copied into other periodicals. They are republished here, solely to enable members and associates to preserve them in convenient form. Various considerations have determined the selection of papers for this purpose. Some have been omitted at the request of the authors who, having modified the views expressed in them, naturally deprecated a republication of those views. Others have been omitted, in order not to devote too large a proportion of space to single topics, or single branches of mining or metal¬lurgy, in view of the fact that the membership of the Institute extends throughout the whole country, and represents numerous departments of these industries. Some, on the other hand, have been chosen, although not laying claim to special originality, because they contained information of importance, not easily accessible elsewhere, the presentation of which, in a form convenient for reference, was generally desired.

Jan 1, 1921

By A. U. Seybolt

The solubility of oxygen in a iron has been determined in the range between 700° and 900°C. The solubility is a function of temperature and varies from about 0.008 pct oxygen at 700°C to atureandabout 0.03 pct at 900°C. The heat of solution is approximately +15,500 cal per mol. AS pointed out in a recent paper by Kitchener et al.,1 there has been a lack of agreement among many investigators even as to the order of magnitude of the solid solubility of oxygen in the various forms of iron. This lack of agreement is attributable in large part to the difficulties in the determination of a small oxygen solubility; but because the problem has remained so long unsettled, it also indicates a lack of interest which is rather surprising when the demonstrated importance of small amounts of soluble nonmetallic impurities in iron is considered. The work of Kitchener et al. apparently leaves the solubility of oxygen in iron in a satisfactory state, but no attempt was made to investigate the solubility in a iron. The solubility of oxygen in a iron is actually of greater interest, since it is in this form that iron and mild steels are employed ordinarily. That the effect of oxygen in iron is of more than theoretical interest has been well established by Fast,' and more recently by Rees and Hopkins," who demonstrated that oxygen in the range between 0.0008 and 0.27 wt pct has a pronounced effect upon the mechanical properties. Previous Work and Methods Used To report in detail the literature relating to the solubility of oxygen in a iron would require an inordinate amount of space. For those interested in reviewing this work, a bibliography4-13 of the more significant papers is appended. In general, two methods of studying this problem have been used. One is the gas-metal equilibrium method where the H2O-H2-Fe or the CO2-CO-Fe equilibria have been used. The other is the more direct approach of the oxidation of thin strips of pure iron by packing in mill scale or by air or gaseous oxygen at some desired temperature. In this method oxygen is allowed to oxidize the surface and then to diffuse inward until saturation is obtained. In the gas-metal equilibrium method the oxygen dissolved in solid iron at a given temperature is proportional to the ratio of the water vapor-hydrogen pressures or the CO2-CO pressures over the sample for small ratio values. If the ratio becomes higher than a critical value, then an oxide phase makes its appearance (the solution becomes supersaturated). In principle, it is possible to use a series of H2O/H2 or CO2/CO ratios and to find by analysis the corresponding amounts of oxygen in solid solution at constant temperature. At the point where a very small increase in the gas ratio (increase in oxidizing powder) produces a large increase in oxygen content, the solid solubility limit is reached. Alternately, if the critical ratio is known, it is possible to use the procedure of Kitchener et al.1 and to use a ratio which is near but below the critical one. The solubility corresponding to this lower ratio will not be the saturation solubility at the temperature employed, but the saturation solubility can be calculated by multiplying the measured solubility by the critical ratio over the ratio used. However, in the case where oxygen gas is the oxidizing medium, the saturation solubility is not a function of pressure, providing the pressure exceeds the dissociation pressure of FeO in equilibrium with iron. This is 1.2x10-16 mm at 800 °C, according to Dushman." As pointed out by Darken17 in discussing the FeO phase diagram, most of the possible errors tend to yield high values of oxygen solubility. For example, one circumstance which evidently caused the reporting of many high values was the use of finely divided or powdered iron in the gas equilibrium method. Because of the large surface area of such a sample, and the likelihood of some surface contamination if only by exposure to air, the results tended to be high. The direct oxidation method which was used in this work has the advantage in that it is simple and direct, but it suffers from one disadvantage: equilibrium can only be approached from the low oxygen side. The important factors to be kept under control are the following: 1—use of high purity iron to avoid internal oxidation (oxidation of readily

Jan 1, 1955

By ARTHUR THACHER

PRIMITIVE man supplied his wants as they arose; as he became more civilized he anticipated them by producing more regularly and storing the products for future use. This tended to cheapen' production and prevent ' violent fluctuations and therefore tended to increase consumption. In order to anticipate our wants, we must know what these wants will be, and this can be .determined only by statistics. 'While we have made great progress in gathering statistics, they are still far from what they should be; especially metal statistics. We determine fairly, well the amount produced, but this does not answer all inquiries because of the erratic conditions of mining, it is necessary to carry larger stocks of metals than of most other articles; moreover, as metals are more or less durable, it is difficult to determine the actual consumption. We often count under consumption what is being produced and sold, while the actual consumption is what is being worn out.

Jan 1, 1921

By R. I. Jaffee, C. T. Sims, C. M. Craighead

The fabrication of rhenium metal by powder metallurgy techniques is discussed. The following physical and mechanical properties have been measured and are reported: lattice constants, melting point, electrical resistivity, thermal expansion, spectral emissivity, modulus of elasticity, tensile properties and ductility at room and elevated temperatures, work hardening, recrystallization, grain growth, and oxidation resistance. IT is only occasionally that a metal reaches present-day technology with as little known about its properties as element No. 75, rhenium. Relatively scarce to date, it has been studied only infrequently and used less. Previous work on rhenium has been carried out primarily by European scientists. However, realization that rhenium occurs in commercial quantities in the United States recently has focused attention on this metal. Rhenium is a very dense high melting hexagonal-close-packed metal. Like tungsten and molybdenum, its highest oxide is volatile. However, when protected by reducing or inert atmospheres, its strength at high temperatures is greater than that of tungsten. Rhenium work hardens more than any other known pure metal, but, on annealing, becomes quite soft and ductile. Its vapor pressure is approximately that of tantalum, but it does not enter into the so-called "water cycle" nearly as readily as does tungsten. (The water cycle is a deleterious phenomenon causing blackening of lamp bulbs and vacuum tubes with subsequent failure of the filaments.) These and other properties, some already known and some found as a result of the current researches, have indicated that rhenium has many potential uses, primarily of an electrical or electronic nature. Rhenium or its alloys soon may be found in service as electron-tube filaments, cathodic emitters, or as electrical contact materials. In addition, rhenium or its alloys have potential use in such devices as high temperature thermocouples, and high wear-resistant parts such as precision instrument points. Rhenium, in the form of potassium perrhenate, was made available for this study by the Kennecott Copper Corp. The potassium perrhenate was reduced to rhenium metal in two stages, accompanied by leaching to remove potassium in the form of hydroxide. This impure metal was then oxidized to rhenium heptoxide and dissolved in water. The solution was neutralized with ammonium hydroxide to produce highly purified ammonium perrhenate, a typical analysis of which is shown in Table I. The ammonium perrhenate was ground to —325 mesh in a rubber-lined ball mill with Burundum balls. This operation caused a certain amount of impurity pickup, as reflected in the rhenium analysis shown in Table I. The fine ammonium perrhenate was reduced to metal with hydrogen. Particle size of the powder ranged from 1 to 25 microns, as illustrated by Fig. 1.

Jan 1, 1956

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951

By Murray F. Hawkins, W. J. Ainsworth

In all types of subsurface pressure gauges the extension which occurs in the pressure-sensitive element is a function of the difference between the external (well or calibration) pressure and the internal pressure within the gauge, rather than a function of the external pressure only. The internal pressure is near atmospheric and depends upon (a) the quantity of air sealed within the gauge at the time of calibration or measurement, (b) the quantity of moisture (liquid water), if any, sealed within the gauge, and (c) the temperature at which the calibration or well measurement is made. Part of this correction for the change of internal pressure with temperature is taken care of by the customary temperature coefficient of the gauge. However, part of it is not, and while this portion may be only a few psi, it is nevertheless predictable or preventable, and should be considered in precision measurements. ERROR NO. 1 If air is sealed in the gauge at the same temperature and pressure for both the calibration and the well measurements, the usual temperature correction will take care of any difference between calibration and well measurement temperatures. However, if air is sealed within the gauge at temperature T1 and pressure P1 at calibration but at temperature T2 and pressure P2 for a well measurement, because different amounts of air are sealed within the gauge in each case, the internal pressure at. or corrected to, calibration temperature Tr will he different by where all temperatures and pressures are absolute. The calibration temperature is used, and not the well measurement temperature, because the usual temperature correction reduces the well measurements to calibration temperature. The correction term as calculated by the above equation is separate from. and in addition to, the usual temperature correction. Example: T, = 540°R, sealing temperature at calibration P, = 14.7 psia, sealing pressure at calibration T2 = 460°R, sealing temperature at well P2 = 14.7 psia, sealing pressure at well Tr = 660°R, calibration temperature AP = 660 [14.7/460 — 14.7/540] = 3.1 psi While this error is small even under these somewhat maximal conditions, it nevertheless represents a practical situation which did occur, and which as a matter of fact gave rise to this note. Where AP is positive, as above, the correction is added to the measured pressure; where negative, subtracted from the measured pressure. This correction should also be considered in successive calibration runs where the gauge, for example, may be warm from a previous calibration at an elevated temperature. ERROR NO. 2 Where a small quantity of moisture (liquid water) is sealed within the gauge at atmospheric conditions, the increased vapor pressure of the water at higher well or calibration temperatures will cause an increase in internal pressure. This moisture will come presumably from condensation within the gauge following temperature changes, from moisture on the operator&apos;s hands, and from atmospheric moisture (rain, mist, fog, etc.). Calculation shows that approximately 0.2 cc of water (three to four drops) is sufficient to saturate the air within an Amerada RPG-3 Gauge at 160°F, at which temperature the vapor pressure of water is about 5 psia. As the vaporization occurs in a sealed volume, the increase in internal pressure will be in excess of this 5 psi. At higher temperatures the pressures will be higher; however more water will be required to saturate the air within the gauge. Some experimental work was carried out with an Amerada RPG-3 Gauge at 200°F fitted with a 1,000 psi element, both with a dry recording chamber and with a small amount of water added. The results directly proved the existence of the error due to the presence of moisture, and, it is felt, indirectly, due to the differences in sealing temperatures and pressures, as both effects may be ascribed simply to an increase in the moles of gas within the recording chamber. SUMMARY In precision measurements the error introduced by sealing the gauge during a well test at a different temperature and pressure from that of calibration may be corrected for by using the equation presented, or it may be prevented by taking care always to seal the gauge at near calibration conditions. The error introduced by sealing moisture in the gauge may be prevented by taking care to keep moisture out of the gauge, or by removing the moisture by either warming or evacuating the gauge. Both of these errors are independent of the range of pressure measurement and the type of gauge, and are in addition to the usual temperature correction. ACKNOWLEDGMENT Appreciation is expressed to W. B. Kendall, Geophysical Research Corp., Tulsa, Okla., who pointed out the error from differences in sealing temperatures during some winter work in Canada. ***

Jan 1, 1956

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d&apos;Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in. a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a. previous paper.&apos; The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques. The general geo1ogy of the Coeur d&apos;Alene district, including a detailed description of the rock types encountered, has been comprehensively treated by Ransome and Calkins&apos; in their classic paper, and only local background description, therefore, is felt to be appropriate here. The Hercules deposit transects a portion of the trough of a broad south-trending synclinorium which has been greatly complicated by faulting. More locally, it lies within a block of ground bounded on the east; by the O&apos;Neil Gulch fault, a steep north-south overthrust of considerable magnitude, and on the west by a monzonite stock, the outcrop of which is 1/2 mile or more wide and 5 miles long. The country rock is composed of thin to medium-bedded argillites and argillaceous quartz-ites of the Prichard and Burke formations, the oldest members of the Pre-cambrian Belt Series of sediments in the area, believed to be of Algonkian age. The contact between them is a conformable gradation. The argillite is colored gray to tannish-gray and is fine-grained, compact, and generally massive in structure. Under the microscope the unaltered argillite is seen to be composed principally of anhedral quartz and a few feldspar grains which were at one time presumably partly rounded sand grains, but as a result of recrystallization and cementation by silica, the interstices are now almost obliterated and quartz grains show crenulate boundaries. The sizes of these crystals vary from 0.5 mm down to 0.1 mm in greatest dimension. In all specimens sericite comprises 10 to 20 pct of the rock and is present abundantly between most of the grains as flakes or shreds which vary considerably in size. Sometimes they form a fine felt-like mat or aggregate, and sometimes flakes are seen which appear to be good muscovite. In some specimens, separated rhombic-shaped carbonate grains are abundant, and in some instances these have been changed to sericite. Mining operations to date have explored the Hercules vein to a maximum vertical depth of 3600 ft below its outcrop, and along a maximum strike-length of 3600 ft on certain of the lower mine levels. The main orebody is irregular in outline, extending over a variable strike-length of 400 to 1500 ft; and it is intersected by a strong transverse fault that has been traced from the surface to the bottom level. This has been named the Hercules fault, and apart from the vein itself, it is the most prominent structural feature in the mine. There is good evidence that it existed prior to the introduction of ore solutions and may have influenced ore deposition, but it was also the locus of important post-ore displacement and shows a progressive right-handed horizontal component reaching 200 ft on the deeper levels. Its vertical component is not definitely known but may be considerably greater. The fault strikes 20° N to 50° E and dips westerly at angles of 70" to 45", flattening in dip where it crosses the original orebody from east to west between 1000 and 1600 ft below the surface. At about 3000 ft in depth the Hercules fault is joined by a vertical fault of similar strike, and the major post-ore dis-placement below their junction is taken up along this vertical branch of the structure, now called the Mercury fault. Recent work has been concentrated in this vicinity. Another structural feature of special geologic interest, though of little economic importance, is the occurrence of a porphyritic dike in this area. This lies a short distance above the Hercules fault, essentially parallel to it, and is 5 to 15 ft in thickness. It appears at first glance to cut the mineralization, suggesting push-apart relationship, but small stringers of the vein minerals have been observed to penetrate the dike for a matter of inches at several points. The dike is thought to be related to the monzonite intrusion. A vertical longitudinal projection of the mine is shown in Fig. 1, which illustrates most of the features discussed above. The Hercules vein was deposited along the course of a strong, persistent shear zone that now appears as a braided network of gouge seams running through more or less crushed and shattered country rock. It strikes 70° N to 80° W and dips southerly at an average of 75". Barren parts of the structure vary in width from less than 1 ft to more than 15 ft. The width of mineralized segments may be double that. Although the evidence is not conclusive, pre-mineral, normal movement along the zone may be 1000 or 1500 ft. The horizontal component is unknown. Post-ore movement appears to have been

Jan 1, 1954

By Jacques B. Wertz

Among the parameters to be considered in the continuous search for new base-metal deposits, there often is a stratigraphic controlling factor that seems instrumental in the localization of ore. In British Columbia, for instance, the Upper Triassic as well as Lower Jurassic volcanics mixed with sediments are a useful indication in the search for copper while, in some parts of Australia, rhyolite bodies seem to be the favorable indicator, and this always within the geosynclinal environment. In Arizona, this stratigraphic factor becomes highly significant and it will be shown here that a large number of ore deposits are to be located around the flanks of ancient calcareous basins or depressions, preferentially corresponding to a certain optimum thickness as revealed by isopachs. The Martin limestone, of Devonian age, is already known for its basal O&apos;Carroll bed which coincides with mineralization at places, and this is a relatively minor control. However, several limestone basins outlined by isopachs are in reality of greater importance as they localize mining districts. Indeed, most mines are found to coincide with a specific thickness of limestone while occurring simultaneously close to major, regional fracture intersections. The regional fractures in question were interpolated and extrapolated from known, important fault expressions, integrating quite well with the existing geology and further confirmed by minor criteria such as contacts, igneous plugs, axes of elongation of batholiths, dikes, etc. Although elements of subjectivity remain, this grid of fractures can be used quite successfully as a working hypothesis in the search for ore. Results of the present study which superposes major structural

Jan 1, 1971

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.&apos; Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method&apos; was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.&apos; Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By R. S. Sherwin

The extractive metallurgy of primary aluminum from its ores is discussed with special attention to the production of alumina from high grade ores by the Bayer process, including differences between American and European practice and a brief description of some processes for lower grade ores and the electrolytic reduction of the oxide to aluminum. METALLIC aluminum is not found in nature, but the oxides, hydroxides, and especially the silicates are plentiful. The estimated percentage of in in the crust of the earth is about 8 pct while that of iron is about 5 pct. By far the larger portion of this is combined with silica in the form of various clay minerals and igneous silicate rocks. From the point of view of extractive metallurgy of aluminum, these are low grade ores while the better qualities of bauxite are the high grade ores. There have been various definitions of bauxite but perhaps the best definition at the present time is that bauxite is a rock or earth commonly used as an ore of aluminum or its salts in which the aluminum is present predominantly as a hydrate or a mixture of hydrates and hydrous oxides. It contains varying amounts of oxides of silicon, iron, and titanium and traces of compounds of some of the less common elements. The silica is mainly combined with alumina as clay or clay minerals which are hydrous aluminum silicates, although a part of it may be present as quartz sand. On the American continents, the alumina is mainly present as gibbsite, Al2O3 . 3H2O, and the same may be said of the best known deposits of the Dutch East Indies and some of the deposits in India. In France and other countries in Europe as well as in Africa, the alumina is present mainly as boeh-mite, A12O3 . H2O, but in some of these deposits it is mixed with minor amounts of gibbsite. Some other deposits, such as those in the islands of Haiti and Jamaica, evidently contain two or more hydrates or hydrous oxides of alumina in varying proportions. Perhaps the main portion of the alumina may be present as gibbsite and boehmite with the proportion between the two varying rather widely. In the silicate minerals, including clay, the alumina is chemically combined with silica and has not been separated satisfactorily by mechanical or physical ore-dressing methods. Low grade bauxites are mixtures of hydrates, usually gibbsite or boehmite, with clay, iron oxides, etc. In some low grade bauxites, it is possible to separate a portion of the gibbsite or boehmite, which may be present as relatively hard and coarse particles, from soft or finely divided clay minerals by log washing or similar methods. This has been applied to the product of some mines or parts of them, but on other ores it is not applicable. In some cases the gibbsite or boehmite is almost as fine and soft and of nearly the same specific gravity as the clay minerals so that washing and gravity separations are not successful. The iron oxide, the clay minerals, and a part of the titanium minerals are often so finely dispersed in the ore that any of the physical mineral separation methods, including separations by gravity, particle size, flotation, and electrostatic or magnetic separation, have not been commercially SUCCESSFUL except on relatively small lots of ore. For these reasons, the only available methods of separation on the general run of ores have been methods which would be classed as chemical rather than physical or mechanical separations. Aluminum oxide can be reduced by carbon at temperatures above 1800°C to form metallic aluminum and aluminum carbide or nitride. The temperature for rapid reduction of aluminum oxide to metallic aluminum is about the boiling point of aluminum and above the temperatures necessary to reduce iron, silicon, and titanium so that the direct reduction of an aluminum ore with carbon will produce an alloy of aluminum, iron, titanium, silicon, etc., which may be mixed with carbides and nitrides. Also a large amount of the reduced aluminum may be lost as a vapor except in the presence of some alloying agent such as copper or other metals. While it is possible to refine such alloys or mixtures so as to produce commercially pure aluminum, the methods which have been found are too expensive for the present market. One direct reduction method which found limited commercial use in Germany during World War II was the direct reduction of a mixture of clay containing very little

Jan 1, 1951