Search Documents

By W. R. Shimer

IN his valuable report on Finishing Temperatures and Properties of Rails, I Dr. G. K. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying put the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. . Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development ,of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high per centages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility, than. rails of identically the same composition and section which were rolled, direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 3, 1915

By John Dodd

This paper reviews advances in the technology of abrasion resistant iron and steels, which could help combat abrasion and wear in mining operations. With the recent progress in high chromium alloy iron development, high temperature heat treatment of massive castings can be eliminated, aloy cost reduced, and cracking problems avoided. Data on erosion-corrosion resistance of these irons; trends in the development of improved cast steels; and factors influencing toughness and abrasion resistance of manganese steels are all considered. The 7% Mn. 1% Mo manganese steels are shown to combine toughness and abrasion resistance, and composite castings are a means of combating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1982

By Edmund M. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence-the total absence of noise except for one's own breathing and scuffing of boots on the bottom. An underpound mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working in the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969." As [Fig. 1] indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which govern noise exposure in many industries. In most industries noise exposure is not a constant value. Noise emitted from coal mining machinery varies widely, and therefore interpretation of compliance is not a simple matter. Time, environment, instrumentation and machine productivity, as well as the designed machine characteristics affect the results. It is the purpose of this paper to present the underground coal face machinery noise problem from a manufacturer's point of view. Manufacturers are very much aware of their responsibility to alleviate the noise problem. Not infrequently, orders are received from coal operators that a given new machine must comply with "The Coal Mine Health & Safety Act" noise regulations. Such a request is indicative of the misunderstanding which exists with machine users, while indicating their desire to comply with the law. Obviously, if all machinery could be designed and used at some arbitrary low noise level, it would be possible to simplify the regulations. However, there still remains the pervasive problem of existing machines. Extensive investigation to create practical retrofit kits for existing machines, to substantially reduce noise have been only marginally successful. Certain machine mechanisms are inherent noise makers. The only really good solution is to substitute a quieter mechanism. Such overall new designs have been undertaken, and several examples are mentioned later in this paper. Before describing machine noise problems, it is necessary to define noise values. Noise levels are measured in decibels. The designation "DBA" is decibels measured on the "A" scale, or one in which the frequency sensitivity of the instrumentation is about the same as the human ear. The numbers are often misinterpreted because it is a logarithmic, rather than an arithmetic scale. In comprehending the numbers, it should be remembered that any increase of 3 dB doubles the sound power. In practical terms this means that two noises of equal power at the same distance away increases a dB reading by three. Consider [Fig. 2] showing a simplified case of a worker on a machine subject to

Jan 1, 1980

By Rebecca Mae Summer

Increasing urbanization and industrial activity require increased supplies of sand and gravel. This means expanded surface mining and despoiled land near population centers. Highly competitive land use demands justify serious consideration of premining planning for multiple land use and reclamation concurrent with mining, 1-5 Formulating solutions to environmentally and economically sound uses requires a comprehensive approach based on properties of the natural resource base--geology, soils, and water. A study of sand and gravel mining within Pleistocene-Holocene fluvial deposits in Colorado County, Texas (Fig. I) illustrates how physical limitations imposed by the resource base are determined.6,7 Data from drillers logs of water wells, test boreholes, field observations, and laboratory analyses are used to evaluate these physical controls.

Jan 1, 1978

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By F. A. Crossley

The titanium-rich end of the Ti-A1 system has been investigated up to 35 at. pct A1 (23 wt pet). One conzpound Ti3Al was found to occur between primary a and TiAl. It is ordered hcp with DO19 structure, it has virtually no solid-solubility range, and it has a closed maximum at about 875°C. OIL either side of the compound are a +Ti3Al two-phase fields. The limiting a1uminum solubility in primary a at the titanium-rich end is indicated to be 7.5 at. pct A1 (4.4 wt pet) at 550°C and about 6.8 at. pct Al fl wt pct) at 500°C. Quenching alloys from above the a + Ti3Al two-phase field produces the following structures with respect to alloy composition: Up to 13 at. pct A1 (7.8 wt pet), a solid solution; from 15 to 18 at. pct A1 (9 to 11 wt pct), shear transformation product or martensite; from 19 to approximately 30 at. pct (11 to 19 wt pet), submicro-scopic coherent Ti3Al in an a malvix. The twin hcp phase fields reported in the literature are the result of nonequilibrium corzdztions. Ti-A1 alloys, once partitioned by dwelling- in the a + ß phase field during either hot working or heat treatment, are extremely difjicult to homogenize at temperatures below 1000°C. Such partitioned alloys exhibit the characteristics or symptoms of two-phase materials, and may be said to suffer the "twin-phase syndrome". THE earliest investigations of the Ti-A1 system by Ogden et al.1 and Bumps et al.2 reported wide solubility of the primary solid solutions. Aluminum was reported soluble in the low-temperature allomorph to the extent of 37 at. pct (25 wt pct), and the first intermediate phase was reportedly TiA1. Somewhat later Kornilov et al.3 reported a similar diagram with phase boundaries displaced towards lower aluminum contents and higher temperatures. Beginning about this time (1956) reports in the literature made it very clear that one or more intermediate phases occurred at lower aluminum contents than TiAl.4-17 These reports included five major investigations of the titanium-rich end of the Ti-A1 diagram.4,12,14,16,17 Three of these diagrams show two two-phase fields below 37 at. pct Al, while two of them show a single two-phase field. The existence of the phase Ti3A1 is firmly established and is included in each of the diagrams, except one—that of Sato and Huang.12 The new phases are reportedly hcp and differ from primary a only slightly when disordered, and when ordered the "a" parameter is approximately one,4,12,15 two, 6-10,13,14 or four14 times that for primary a. Beyond this, however, the diagrams are remarkable for their lack of agreement. Two tacit assumptions are usually made in phase-diagram determinations of metal systems. These are: 1) equilibrium anneals bring the alloy to equilibrium or to indistinguishable closeness to it, and 2) equilibrium conditions established at elevated temperatures are either "frozen" by rapid quenching for evaluation at room temperature, or quench-transformation products are recognized as such. In the current investigation evidence was obtained that over substantial composition ranges neither of these two conditions was met in any of the more recent major investigations. I) MATERIALS, METHODS, AND TECHNIQUES The alloys of this investigation were prepared by nonc on sum able electrode arc melting. Materials used in the preparation of the alloys are summarized in Table I. The investigative tools employed were: optical and electron microscopy, differential thermal analysis (DTA), disatometry, X-ray diffraction, electron diffraction, and resistometry. Alloys for microscopic and X-ray investigations were prepared as 15-g melts. Alloys containing from 7 through 11 at. pct A1 were hot-rolled out of a furnace at 900°C, from 12 through 15 at. pct out of a furnace at 1000°C, and from 16 through 18 at. pct out of a furnace at 1125°C. Alloys containing more than 18 at. pct A1 could not be hot-rolled. The ingots were covered with Markal coating prior to hot rolling to minimize atmospheric contamination. After hot rolling, alloys containing up to 15 at. pct A1 were ground and pickled to remove 7 mils from each surface; alloys containing 16 and 18 at. pct A1 were skinned to a

Jan 1, 1967

By H. B. Pulsifer

ABOUT 15 varieties, or modifications, of the best magnesium available were prepared and subjected to etching tests, then examined for microstructure. Of the 30-odd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressure cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium are presented in two reduced photographs and 30 photomicrographs. MATERIALS TESTED There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½ -in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 1 3/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½ in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from distilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

Jan 1, 1928

By B. K. Miller, R. S. Bradley

THE principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties [ ] (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic[$] fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north central Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semiplastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1941

By J. A. Scott, F. R. Hensel

The paper deals with the investigation of two types of coreless induction furnaces, one of 60 cycles, the other of 5000 cycles. Nickel was used as test material and the absorption of oxygen by molten nickel was chosen for determining the influence of the frequency on the metallurgical characteristics of the furnaces. Dr. Herty's aluminum method, slightly modified, was found suitable for determining the nickel oxide content in nickel. Also an electrolytic method for determining alumina in nickel was worked out. The solubility-temperature relations for nickel oxide in molten nickel were determined approximately. It was found that the solubility of nickel oxide increases with the temperature. Comparative tests on the rate of oxygen absorption made in a 60 and a 5000-cycle furnace showed that the absorption of nickel oxide in nickel is an increasing function of turbulence, time and temperature. The rate of oxygen pickup in the 60-cycle furnace is about three times as great as in the 5000-cycle furnace. In the 60-cycle furnace the maximum oxygen content of the melt comes close to the saturation limit. Melting under an oxygen-free atmosphere prevents oxidation in both types of furnaces. DISCUSSION (Iloward Scott presiding) H. Scott, East Pittsburgh, Pa.—When Professor Desch was in Pittsburgh recently he mentioned that the induction furnace has practically replaced the crucible furnace in Sheffield except for the carbon tool steels. Dr. Hensel is to be congratulated on the development of analytical methods for determining inclusions and for getting two different methods to agree. F. R. Hesnsel—Recently the purification of molten metals with hydrogen or other suitable gases has become an important issue and a number of patents have been taken out covering gaseous treatments of molten metals. In this connection I wish to call

Jan 1, 1933

By Ernest F. Burchard

The Pao deposits of iron ore are in the State of Bolivar, Venezuela, near Upata, about 30 miles south of the Orinoco River and 90 miles east of Ciudad Bolivar. They were discovered 4 or 5 years ago and have not yet been developed to the stage of mining. In March-April, 1929, the writer devoted a week to the examination of these deposits. The maps, drill records and chemical analyses presented herewith were derived from original sources, and the field photographs were made by the writer. The petrographic and metallographic data are from notes by C. S. Ross and M. N. Short, of the U. S. Geological Survey, who have kindly collaborated in these special phases of the study. The Iron Obebodies Topography and Accessibility The deposits are in a region of low mountains representing northern outliers of the Guayanan Highlands. These mountains reach altitudes of 1800 to more than 2000 ft. above sea level, as determined by aneroid barometer. The iron ore is found on mountain crests that reach altitudes of 1915 to 1930 ft., and may be followed down precipitous slopes for 200 • to 300 ft. or more. The greatest vertical range in outcrop is nearly 400 ft., and drilling has indicated that the ore extends to this depth below the surface in one place, at least. The superior hardness of the iron ore accounts for the preservation of the local mountain crests with the intermediate valleys eroded in softer granitic rock. The deposits of iron ore are reached by a private road for automobiles branching northeast from the Ciudad Bolivar-Upata road, a distance of about 12 miles. This road was used in 1928-29 by trucks for transportation of food and camp supplies, gasoline, drilling equipment, etc., but was not suitable for the transportation of iron ore. Between Ciudad Bolivar and the iron-ore area the western two-thirds of the automobile road passes through nearly level, open country known as the savanna, largely used for grazing cattle. About 96 km. (60 miles) east of Ciudad Bolivar at

Jan 1, 1931

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1942

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1934

By Catherine T. Aimone

Specimens of copper-bearing quartz monzonite were subjected to a plane shock wave simulating high compressional stresses in the proximity of a borehole wall. Fragmentation was studied as a function of stress levels between 1.6 GPa (23 x 104 psi) and 7.3 GPa(105.8x104 psi) and pulse durations ranging from 1.1 µs to 6.9 us. Both explosive pressure and pulse duration were shown to have a strong effect on particle size distribution. While the effect of pressure is well recognized, the effect of pulse duration indicates that ultimate fragmentation increases with the time of application of a plane wave pulse. At high pulse durations, degree of fragmentation is more sensitive to changes in pressure than at low pulse durations.

Jan 1, 1984

By P. A. Young

The historical background of on-strand cooling is given, together with a resume of recent practical developments. Laboratory test procedures are then considered in detail, for both productivity and quality parameters, with particular reference to the design of the Ravenscraig No 3 machine (Scotland). A heat transfer model is presented for a porous sinter with propagating cracks. The influence of cooling/sintering area ratio, sinter strength, granulometry, return fines, coke consumption and FeO levels are examined in relation to economics. A detailed comparison of capital and running costs for two different strands, designed for identical duties, but with off or on-strand cooling, is then given.

Jan 1, 1977

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1932

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNS Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B.. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. A. H. EUSTIS, F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 5, 1916

By John F. Barkley, J. W. Woomer, H. F. Yancey, H. B. Charmbury

The coal picture in 1955 was much brighter than in 1954, when the tonnage produced dropped to the 1939 level. Bituminous coal and lignite production are expected to approach 465 million tons, against 392 million tons in 1954, an increase of about 19 pct. On the other hand, the production of anthracite declined about 7 pct to some 25 million tons. There was marked improvement in coal consumption in all industrial lines except railroads. At the end of November 1955 the largest consumer, electric power utilities, had used about 126 million tons, an increase of some 22 million tons over the previous year. Coke-oven consumption increased about 19 million tons and coal coked in beehive ovens increased about 1.5 million tons, due to heavy coke

Feb 1, 1956

Trans No. Place Date Vol. 1. Wilkes-Barre, Pa. May, '71 1 2. Bethlehem, Pa. Aug., '71 1 3. Troy, N. Nov., '71 1 4. Philadelphia, Pa. Feb., '72.. 1 5. New York, N. Y. May, '72 1 6. Pittsburgh, Pa. Oct., '72 1 7. Boston, Mass. Feb., '73 1 8. Philadelphia, Pa. May, '73 2 9. Easton, Pa. Oct., '73 2 10. New York N. Y. Feb., '74 2 11. St. Louis, Mo. May, '74 3 12. Hazleton, Pa. Oct., '74.. 3 13. New Haven, Conn. Feb., '75 3 14. Dover, N. J. May, '75 4 15. Cleveland, Ohio Oct., '75 4 16. Washington, D. C. Feb., '76 4 17. Philadelphia, Pa. June, '76 5 18. Philadelphia, Pa. Oct., '76 5

Jan 1, 1944