Search Documents

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By Alexander R. Troiano, Eugene P. Klier

SINCE the very early work on quenched structures, where the products of the martensite transformation had been recognized, this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well- established features of the martensite reaction are the progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfortunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielded conficting results, caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are alinear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destruction of the tetragonal structure, which is converted to a body-centered cubic structure. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite. The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Ar" as a function of carbon content was first stated by Greninger and Troianos for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By W. C. Elmore

THE magnetic powder method, long used. for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickels single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By M. T. Simnad, G. Derge, Ling Yang

STUDY of diffusion in molten substances is important in at least two respects. Diffusion data, combined with thermodynamic and kinetic information, throw light on the structure of the liquid state. Moreover, a knowledge of diffusion coefficients and their temperature dependence is useful in ascertaining the controlling step in many metallurgical reactions. Although diffusion measurements have been made on a number of molten salts, slags, metals, and alloys,'-'" the results available are still limited and widely scattered, especially for the high temperature melts. It is the purpose of this investigation to establish reliable procedures for the measurement of self-diffusion coefficients in high temperature melts and to use these procedures to determine the self-diffusion coefficients of iron in molten Fe-C alloys of different carbon contents. Experimental Measurement of self-diffusion coefficients in high temperature melts is usually carried out by using one of two methods. In the first, diffusion takes place between two cylindrical samples of the same material, one of which is made radioactive. The diffusion coefficient is calculated from the radioactivity penetration curve in the solidified sample after the diffusion. In the second method, samples contained in capillaries of an inert substance are immersed in an infinite reservoir of the same material. Either the material in the capillary or that in the reservoir is made radioactive and the diffusion coefficient is calculated from the change of the radioactivity of the sample in the capillary after the diffusion. The second method is simpler because a radioactivity penetration curve is not needed for the calculation of the diffusion coefficient; however,.it is valid only when no convection has occurred in the capillary during the diffusion. A radioactivity penetration curve is therefore always useful in indicating that the required conditions for the diffusion are ful- filled. Towers and Chipman" recently studied the self-diffusion of calcium and silicon in CaO-Al,O,-SiO, melts by using the capillary method. Instead of measuring the change of the radioactivity of the sample in the capillary, they autoradiographed the sample after the diffusion and calculated the diffusion coefficient from the intensity distribution of the autoradiograph. Their method is useful when the radioactive isotopes are weak ß-emitters, but is very difficult, if not impossible, to apply to cases involving strong ß or y-emitters. For such cases, sectioning of the sample according to the method of Morgan and Kitchener' may be used for the construction of the radioactivity penetration curve. The self-diffusion of iron in molten Fe-C alloys has been studied in this manner and the experimental procedures are described as follows: The diffusion apparatus is shown schematically in Fig. 1. The bath consisted of about 200 g of an Fe-C

Jan 1, 1957

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publi-cations of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photo-graphs are used on such scales as soon to 1/5,000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are inter-preted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition': 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE mechanism by which the super-saturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications. 1,2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon {111} matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;3 at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate y but that of a transition lattice ?'. Since this is also platelike in shape and also lies upon the {111} matrix planes with the {110} direction in the matrix parallel to the {11.0} direction in ?', it seems likely that the original platelet particles are merely ?' in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the {00.0} plane in ?' are identical with those on the {111} matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures ?' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, ? ' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system,2,4 hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructure, Brinell hardness and electrical resistivity of the three alloys. PREPARATION OF SAMPLES AND EXPERIMENTAL PROCEDURE The preparation of the 20.2 per cent Ag alloy has been described.2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent Al and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By O. T. Marzke, Robert F. Mehl

A study of the structures arising from the decomposition of the ß solid solutions in the Cu-Zn and the Cu-A1 systems is of peculiar interest in the study of the mechanism of precipitation from solid solutions. It is possible in these alloys, by varying the composition within the ß field, to precipitate from the same basic lattice phases having different lattice structures. It has been rather generally assumed heretofore that the type of structure originating from the decomposition of a solid solution— the Widmanstätten structure—-is determined by the lattice structure of the parent solid solution alone. In the first paper of this series1 evidence was advanced which threw doubt upon this hypothesis; but definite proof of the correctness or incorrectness of the hypothesis should be forthcoming from a study of these alloys, for if the structures originating, for example, from the precipitation of the a phase from ß and of the ? phase from the ß in the Cu-Zn system should be shown to be crystallographically different, the hypothesis would necessarily be held as definitely disproved. Furthermore, the newer proposal enunciated in the first paper of this series—that the origin of the Widmanstätten structure lies in a cooperation between the lattice of the parent solid solution and that of the precipitate-—which at present seems the only a1ternative hypothesis, would in such an event be given added weight. The work here reported shows that the Widmanstätten structures originating in the precipitation of the a phase from the ß and in the precipit'at.ion of the y phase from the y in the Cu-Zn system are indeed crystallographically different; and incidentally presents some new descriptive information on the Widmanstätten structure from a more general point, of view.

Jan 1, 1931

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By Reinhardt Thiessen

In the general study of coal, all evidence points in the one direction —that coals had their origin in a manner analogous to that of peat. The best method of studying coal, whether it concerns its chemistry, composition, or physical condition, is to study peat. The essentials in a study of peat are a knowledge of the chemistry of plants, knowledge of decay and of the transformation process of plant-substances into peat. A number of facts must be emphasized, namely, (1) peat is formed under wet conditions only; (2) plants grow in the place where peat is formed; (3) all the plant substances go into the bog; and (4) all the plant substances are subjected to a series of phases of decay which are (a) in the air completely above the water level but in relatively moist conditions; (b) above the water level, but covered by debris; and (c) completely submerged by both water and debris. Plant Chemistry Plant chemistry as a whole is remarkably well understood. The number of compounds composing plants is large, and it is not possible here to give even a comprehensive outline, but a classification into definite groups is possible; this is as follows: Carbohydrates; glucosides; pigments; tannins; acids, alcohols and ketones, etc., and their salts; essential oils; resins; vegetable bases; proteins; enzymes. Plant substances may also be grouped according to the role they play in the life of the plant, such as: Framework materials, living materials, food materials, protecting materials, waste materials. While this classification groups them well for. certain purposes, it does not group them exactly chemically; but in a consideration of the composition of coal, this is an excellent classification for our purpose here.

Jan 1, 1925

By Spruille Braden

My attendance at this seventy-fifth Anniversary banquet of the A I M E is for me a homecoming, It means renewing associations with old friends, breathing again 'the invigorating mining atmosphere in which I was born and reared, and being among those who remember with affection and esteem the man from whom I inherited a name so intimately linked to-the mining profession Tonight, like a prodigal son strayed from mining into the far countries of diplomacy, I return, to eat and be merry over the fatted calf on this pleasurable occasion , While there is no riotous living in modern diplomacy, you are no doubt convinced that neither did I suffer a mighty famine in those far lands When I entered the Foreign Service, a few mining friends, viewing diplomats as sartorial perfectionists, or "striped pantsers" preoccupied with the art of cookie pushing, no doubt thought me a lost soul Conversely, some of my new colleagues at first looked upon me captiously and later as a reformed character, because they believed all miners to be rough customers, attired in muddy boots and given to direct action and equally direct or even explosive speech In point of fact, these two professions have much in common I do not have in mind the parallel cynicisms that "a miner is a liar with a hole in the ground" and "a diplomat a man sent abroad to lie for his country " I do

Jan 1, 1947

By J. E. Johnson

Charcoal-iron is quantitively so unimportant compared with coke-iron, that its qualitative importance for many industrial purposes is entirely unkriown to many coke-furnace-men, and to the great majority of the inembers of this Institute. To explain this qualitative importance, and explain some of the fact,ors that affect the quality, are the objects of this paper. A brief review of' the commercial conditions governing the charcoal-iron industry is a necessary preliminary to any adequate treatment of the subject. The advent of coke-iron, which transformed the whole iron industry commercially, left intact a limited production of charcoal-iron in the East and South, which has been conducted almays on the basis of high cost and high quality, with correspondingly high selling-price. In the Northwest, particularly in the Lake Superior district, the development has been along totally different lines, for which the close proximity of the great iron-ore deposits and the great forests of that region mere responsible. When the great white-pine forests were removed there were left behind large areas of hardwood and hemlock, to which little attention was paid in the prosperous years of the white-pine industry. But when the latter declined, the demand for lumber, and the presence of lumber-men, probably more skilled than any others in the world, caused the gradual introduction of these woods into commercial use. It was a matter of ancient knowledge that hardwood made an excellent charcoal, and to utilize the cordwood left after the saw-logs were removed, by converting it into charcoal and using it to smelt ore from the adjacent mines, mas an obvious step. In some cases the establishment of the furnace occurred in-

Jan 1, 1913

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

By Felix B. Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36’ W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927

By J. T. Eash, E. M. Wise

In a previous communication1 the improvement in slrength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are presented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for determining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum. 4. The variation in the solubility of this platinum-content phase in the alpha solid solution with the temperature has been determined. This

Jan 1, 1933