Search Documents

By J. Blodget Britton

During the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations mere made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phœix Iron Company, at Phœnixville, Pa., was found to have the composition given in Column I of the following table: I. 11. 111. Composition of Dust from Dust from Dust from Deposits. Blast Furnace. Puddling Furnace. Boiling Furnace. Protoxide of iron,... 1.51 3 08 1.18 Peroxide of iron,... 20.21 33.29 41.00 Alumina,....6.57 12.89 7.54 Lime,.....3.98 .48 .61 Magnesia,.....69 .09 .19 Protoxide of manganese,. . 1.66 .39 .12 Oxide of zinc,....2.84 ........ Oxide of copper,. .. ..06 ........ Silicic acid,....36.00 40.69 38.99 Sulphuric acid,... 7.55 .43 Phosphoric acid,..94 ..94 Arsenious acid,. .. .38 Antimoniousacid,... trace.......... Chlorine,....03 ..03 Cyanogen,.....09 ........ Ammonia,.... trace......... Pottlsh with some sodn,. .. 16.61 ........ Carbonic acid,. .. .. .59 ........ Alkalies, undetermined matter, and loss,.......29 4.49 6.96 100.00 100 00 100.00 Metallic iron,. 16.31 25.70 29.64 Phosphorus,. .. .. .41* 1.55† 1.30†

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios (K values) were obtained for nitrogen, methane, carbon dioxide, ethane and hydrogen sulfide in two natural gas-absorber oil mixtures and in two natural gas-Elk Basin crude oil mixtures. For each mixture of constant over-all composition, data were obtained at 100°, 150° and 200°F and at various pressures in the range 200 to 5,000 psia. Some effects of composition on the K values were obtained to serve as a guide in choosing K's for engineering calculations on other mixtures. The pressure cell used to obtain the data is a new type and is described here for the first time. INTRODUCTION The phase equilibria of complex hydrocarbon mixtures such as natural gases, crude oils and their mixtures have been studied previously for the purpose of finding equilibrium vaporization ratios for the hydrocarbon constitutents. In a few cases, such non-hydrocarbon.: as nitrogen, carbon dioxide, and hydrogen sulfide were included in the mixture. studied because they occur. in the fluids obtained from petroleum reservoirs. The increasing occurrerce. of these non-liydrocarbon.; antl their growing economic importance. make it necessary to account for them more accurately in engineering calculation.: than is now possible using the meager published data. The available data for non-hydrocarbons may he classified into two groups: namely, binary mixtures of a hydrocarbon and a non-hydrocarbon. and mixtures containing three or more components, only one of which is a non-hydrocarbon. Amon: the former. phase analyses are available for two nitrogen-HC mixtures, tve carbon dioxide-HC mixtures and three hydrogen sulfide-HC mixtures. Data for more complex mixtures are available as follows: Nitrogen-Methane-Pentane'; Nitrogen-Methane-Hexane,'; Nitrogen-Methane-Heptane'; Carbon dioxide-Natural Gas-Natural Gasorline": Carbon dioxide-Natural Gas-Crude Oil". These data have been used generally lor engineering calculations, often with little regard for their precise applicability because data for the non-hydrocarbons in the complex mixtures being dealt with were not available. The use of K values from binary data for calculation:; involving complex mixtures is open to criticism because such K's are not a function of composition and very often show large differences from the K's for the same components in a complex mixture. Thus the effects of composition must be evaluated when obtaining K's for components in complex mixtures. Poettmann and Katz " varied the carbon dioxide content of their mixture.; from about five to ten mol per cent and found substantially no effect on the K values due to this change. This was not surprising since one might expect that changing a minor com-ponent by * three mol per cent would have little effect. It is more important to find the composition change which have the largest effect on the K values. For example. varying the methane or heptanes — plus compositions over a wide rangr may have a large effect on the K'. of all components in the mixture. Interesting data to this effect were obtained by Eilerts and Smith." It was toward these problems that the experimental data presented here were directed. EQUIPMENT The pressure cell used to obtain the data i:. somewhat dif-ferent from those which have been described in the past. Photographs of the equipment are shown in Figs. 1 and 2. Fig. 1 Shows. the front panel: from a .rated position at the right the

Jan 1, 1952

By Jack R. Elenbaas, Donald L. Katz

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By Donald L. Katz, Jack R. Elenbaas

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By Zay Jeffries

From the title of this chapter the reader could expect an attempt to out- line the anticipated shape of things to come, mineralwise. We have no crystal ball and if we possessed one we could claim no expertness in its use. In the first place no one can tell the future status of man. No one has any way of knowing to what extent peace will prevail, nor to what extent changes may occur in national sovereignties or forms of government or in international relationships. So future man is an uncertainty. Nor can we predict new developments that may result in significant changes in man's status or in the mineral industry or both. If, for example, this chapter had been written in the middle 1930's, nearly everything that has happened since in the fields of atomic energy and space technology would have been missed. Yet what vast changes these I have made in the status of man! Also the changes in the mineral industry have been important. A writer would have been bold indeed had he prophesied that uranium would play such an important role. But we need not confine our foggy vision to these fields. The steep rise in the use of aluminum, titanium, and germanium reflects the unpredictable in what may be thought of as the more normal pursuits. This should not discourage one from using the past and currently observable trends as bases for limited predictions. To do this, however, it is desirable to make certain assumptions about man's status without pretense that these assumptions have a high probability of fulfillment: 1. Only minor changes will occur in the geographical boundaries of the nations of the world. 2. World War III will not take place in the near future. 3. As a consequence of (2), man will not destroy himself by wanton use of atomic weapons. 4. Disarmament will take place, if at all, gradually rather than all at one time. Under the above assumptions the world will enjoy a period of relative peace even though the status may be one of an armed truce. The assump-

Jan 1, 1964

By Basil B. Zavoico

ALTHOUGH the American petroleum industry was affected by the Second World War from its early beginning it was not until Dec. 7, 1941- that the industry was placed on full war footing. Even throughout most of 1942 the American overseas operations were limited and not until late in the year did expansion of military activities, more particularly the offensive in North Africa, affect the domestic supplies to such an extent that critical deficiencies developed locally in this country, particularly along the East Coast. The definite outlook for greatly expanded offensive operations by the United States on both Atlantic and Pacific fronts makes certain that during 1943 the domestic situation will. not be alleviated; rather it may become even more critical even though additional transportation facilities, now being built and planned. will be completed from the southwestern producing states to the East Coast.

Jan 1, 1943

By AIME AIME

EVER since Henry Bessemer, nearly 100 years ago, developed the steelmaking process that bears his name, occasional variation has been noted in the quality of steel made in the acid converter, owing largely to the difficulty of stopping the ? refining-which takes only ten to twelve minutes -at precisely the right moment. Principally as the result of this, the amount of Bessemer steel made in the United States gradually declined over the years until it is now about 7 per cent of the total.

Jan 1, 1943

September 28, 1915. The Nominating Committee of the American Institute of Mining Engineers has the honor to present the following nominations for officers of the Institute to be voted for at the 1915 Annual Meeting: For President: L. D. Ricketts District 0 For Vice-Presidents: Karl Eilers District 0 James MacNaughton District 4 For Directors: Thomas B. Stearns District 7 Charles F. Rand District 0 Charles W. Goodale District 5 Edwin Ludlow District 2 George D. Barron District 0 F. W. BRADLEY, Chairman.

Jan 11, 1915

By R. H. Richman, II Conard G. P.

AS part of a study of deformation twinning in bcc crystals, solid solutions of beryllium in iron have been found to twin profusely when strained slowly at room temperature. This note reports some crystal-lographic aspects of the operative mechanical twin modes in a quenched Fe-5 wt pct Be alloy. After melting twice under a partial pressure of helium, the alloy was homogenized, cut into pieces 7 to 10 mm on an edge, solution treated at 1130°C,1 and quenched. Debye-Scherrer patterns confirmed

Jan 1, 1963

By Renato G. Bautista, Robert A. Hard

A comparative study has been made of the ex-tractability of several of the transitim metals from thiocyanate sohtions using methyl isobutyl ketone as the organic solvent. Extractions were made of scandium (III), chromium (III), manganese (II), iron (III), and cobalt (II), of which only the scandium , iron, and cobalt were readily extracted. All extractions were made at pH 2 and at 25.5 °C. A series of extraction experiments was made on scandium, iron, and cobalt to determine the effect of thiocyanate cmcentration added as the ammonium and also as the calcium salt. Also determined was the effect of metal ion concentratim and ionic strength on the distribution ratio. Analyses of the organic extracts indicated the scandium and iron were extracted principally in the uncharged trithiocyanate form, while the extractable form of the cobalt contained the cobaltotetrathiocyanate anion. THE chemical separation of metal complexes in solution by solvent extraction has in recent years been developed for large scale separation as well as bench scale work in the laboratory. It has also found increased application in analytical chemistry. Its extension to extractive metallurgy as a unit operation is best illustrated in the recovery of uranium and vanadium from their leached liquor.5-8 The extractability of some thiocyanate systems have been extensively investigated. The rate earths have been separated from one another using butanol as a olvent. Scandium was effectively extracted in ethyl ether using ammonium thiocyanate as the com-plexing agent.'' Similarly, the separation of hafnium from zirconium has been reported using ether""' or hexone13 as the organic solvent. The extractability of various metal thiocyanates in ethyl ether is given by 0ck.l Sharp and Wilkinson15 prepared nickel-free cobalt slats by thiocyanate extraction. The mechanism of extraction of titanium (IV) thiocyanate with methyl isobutyl ketone was determined by elafosse.''" The characterization of cobalt (TI) thiocyanate complex using methyl isobutyl ketone as the solvent at near neutral aqueous solution and the spectrometric studies of the ex-tractable cobalt complex has been made by Hard." It is noteworthy to mention at this point that the fundamental characteristic of ketone (oxonium) solvent extraction is that the extractable species are uncharged ion pairs solvated by the ketone molecules, but probably still partially hydrated.

Jan 1, 1963

By George W. Riter

(Canal zone meeting, November, 1910.) A DISTINGUISHED engineer, the active head of a large mining company, has said that surveying attains the dignity of a profession only in the hands of a few men-the few who know how to keep notes that will be understood by even a novice without further word of explanation. Of all mine-records, survey notes are perhaps the most important. The maps made from them serve as a working-guide, and as framework for other data ; and when, from any cause, access to underground workings is shut off, the surveyor's record often becomes invaluable. So seldom does a surveyor have a chance to check underground surveys by making a closure, that he is compelled to rely on the precision of each step of his work for the accuracy of the final result. When data are fully recorded on the spot, the notes, even in the hands of second parties, become evidence of the care and precision with which the surveying was done. It is worth a great deal to be able to pick up the work of a former surveyor where it was left o$; and to be able to carry it forward without retracing from the beginning. The purpose of this paper is to describe the survey-note system of a mine now under my direction, in which underground surveys had to be relied upon entirely for the proper division of rich ore-bodies between neighbors, thereby placing a premium on accurate surveying and permanent records. In survey-work, it soon turns out that paper is the least item of expense, and that little is gained by trying to economize note-book space. For many purposes it is best to record notes on cards or loose-leaves, which may be left in the office at the end of the day's work, and need not be carried into the mine again, there to become smeared with grime and grease. With the loose-leaf or card system, all notes relating to the same local-

Apr 1, 1911

By Nathaniel Arbiter

In attempting to assess the contributions of Antoine Gaudin to the profession which he illuminated for almost a half-century, we will need to examine a very broad canvas. He was active in three significant areas: as a teacher; in research, both through his own endeavors and those of his students; and as a consultant to the mining industry and to the Government. Beyond these specific contributions, there was the major personal influence he had on scores of students, friends, and colleagues in the profession. If a single measure of the man's contribution is to be found, it will be the extent and direction in which he influenced the practice of his profession. To find this we should examine the state of miner- al processing when he began his activities in the 19201s, the progress which has taken place over the past half-century, and the part his activities played in this advance. However, there is a provocative and broader examination which I have chosen to make instead. This is to examine the past century in mineral processing through the lives of three men who, by common agreement, stand on the heights, both in teaching and in their contributions to industry: Robert H. Richards, Arthur F. Taggart, and the man whose memory we honor this evening, Antoine M. Gaudin. Their careers, by coincidence, cover just a century. This is also AIME's first century, and the first century of mineral industry education in the United States. In fact, mineral processing itself on any significant scale in the country encompasses only a century and a quarter. BEGINNINGS OF PRACTICE IN THE U.S. Before the 1840’s, U.S. mining, except for coal and iron ore, was on a small scale and was confined to the eastern states, with processing practically nonexistent. The 1840's saw the beginning of Michigan native copper production, including ore dressing; the 1850’s, iron ore production in Minnesota; and the 1860’s, lead production and processing in Missouri. But the most explosive event was the California gold rush after 1848, which not only brought tens-of-thousands of fortune hunters to the West, but also catalyzed broad mining activities and processing within the following decades. This was not only in California but, after the first fever of the gold rush subsided there,

Jan 1, 1976

By Lucien Eaton

INCREASED mining activity during the past year has brought to light changes in mining practice and advances in technique, born and incubated in the period of depression from which the mining industry is now emerging. Although the tendency toward large output from individual mines has continued, a salutary trend is evident toward greater efficiency at small mines, in which the gold mines of Canada have led the way. Improvement in excavating machinery and washing plants for small placers has continued, and knowledge of the possibilities and limitations of this kind of equipment has increased. Greater portability through sectionalization has been the keynote. Power, shovels and draglines mounted on caterpillar treads move from one deposit to another under their own power, and floating washing plants mounted on pontoons can be taken down, moved, and set up again by a small crew of men in only a few days.

Jan 1, 1937

By G. W. LAAiIBOURNE

FEW mines possess a history of more fascinating interest than the Ontario at Park City, Utah. The famous Bonanza's production record of over $50,000,000; the great extent of its workings; the remarkable character of its mineralization; the fact that recent discoveries have shattered preconceived theories of the geology of the camp practically assuring the half-century old property a future as active and as prosperous as the past make the Ontario one of the unique mines of the world. A mere accounting of the wealth created by this historic property not only exemplifies the great profits

Jan 1, 1925

By Frank V. Hicks

THE following paper-in no sense a technical paper-is a summary of a safety campaign instituted by a coal-mining company to improve an unfortunate safety record. The experience should be suggestive equally to coal and metal-mining companies. With few precedents to follow in the beginning, the course was charted by trial and error. The endeavor, often disheartening, finally resulted in the capture of the most coveted safety trophy in the mining industry, "The Sentinels of Safety," awarded by the Hercules Powder Co. of Wilmington, Del., through the U. S. Bureau of Mines. The period described covers the 10-year interval, 1924 to 1933, the year 1933 being that for which the award was made. The coal company considered has produced annually for a number of years an average of 2,750,000 tons of coal, employing at various times from 1.800 to 3000 men. Prior to 1924, the

Jan 1, 1935

By W. H. Blauvelt

The only way in which the difficult problems of classification of coal for the manufacture of by-product coke can be solved is to analyze them by the use of scientific data. It is very easy to adopt classifications for coal for the manufacture of by-product coke along certain lines; we can easily say that for a certain class of metallurgical operation coke made from bituminous coal must not contain more than so much sulfur or more than so much ash and should yield certain returns in the by-products, tar, ammonia, benzol, gas, etc. Those points we are fairly clear on and I think it is hardly worth while to discuss them because I presume that they are familiar to most of us who have any occasion either to make coke or to use it. But there is a field in the manufacture of coke which we know very little about. For example, we are operating a plant on a certain mixture of coal. Suddenly our blast-furnace man or the user of the coke tells us the coke is not as good as it was before. The coke is analyzed and the coal is analyzed. Everything seems to be about the same as it was— the ash is the same, there is no more sulfur, and so on—but the coke, for the use to which it is put, particularly in the blast furnace, is wrong. What happens? The management decide to try a slightly different coal mixture. They do not necessarily raise the total hydrocarbons, the volatile matter in the mixture, nor change the sulfur or the ash, but they do make a change which improves the value of the coke for metallurgical use. The reason for this difficulty, as I see it, is the " combustibility " of the coke—I hesitate to use the word, but it is the best one I have available. Combustibility of Coke We know now that the combustibility of coke is a very vital point in many metallurgical processes and I think one of the most notable instances of the proof of this is the experience of the Carnegie Steel Co. in the production of coke at its Clairton plant. The history of that

Jan 1, 1930

We have seen that the first coal development in Pennsylvania was in the Pittsburgh bed in the southwestern corner of the state. The next mining, in point of time, was done in Clearfield County along the West Branch of the Susquehanna River, but the amount of mining done was quite small for a number of years and was soon exceeded by that from the area north of the Susquehanna River in Tioga, Bradford and Lycoming Counties, which will be considered now. It is claimed that coal was first noticed in Tioga County, in 1792, by Robert and Benjamin Patterson who were leading a party of settlers from Williamsport to southern New York, and while clearing a road near the site of Blossburg, found coal, which was said to be good. About 1815 David Clemons made an arrangement with Aaron Bloss, owner of the land, to work some of the coal and hauled the first load down the river to Painted Post, N. Y., as there were no available markets in his own state. Smiths found it an excellent fuel and apparently he found a ready market for the small amount he could transport by wagons and sleighs. As wood began to become scarce around the towns in New York State, the knowledge of the coal deposits in the mountains at the head of the Tioga River attracted attention to the field and the necessity, for means of transportation from it. Some coal had been floated down the river, but navigation was uncertain and dangerous. In 1827 an iron plant was built, and to ship its product and coal, it was proposed to build a canal along the river to reach Corning, N. Y. A company had been chartered in 1826 in Pennsylvania to "make a navigable canal or slack-water navigation" to the state line and coal was shipped on rafts of logs, both being sold, during highwater. In 1828 the company was authorized to build a railroad instead of a canal, and in September 1840, the railroad was completed from Corning to Blossburg.1 That some coal from Pennsylvania had been reaching southern New York towns prior to the improved means of transport is shown by the report of a committee to the New York Assembly: "the bituminous coal has been brought to us either from Great Britain or from that part of our own country which borders on, and lies west and south of the Susquehan-

Jan 1, 1942

By S. J. Leach

The possible solution of some of the problems raised in H. L. Hartman's article "Determining Ventilation Requirements for Continuous Miners," which appeared in the March 1962 issue of MINING ENGINEERING, is offered by recent investigative work done at the Safety in Mines Research Establishment, Ministry of Power, Sheffield, England. Highlights of this research are outlined here. Accumulations and layers of methane form in a mine roadway because it is difficult to mix methane with air beneath it by turbulent diffusion. Such mixing involves work contrary to buoyancy forces. In specifying requirements for good ventilation it is not, therefore, sufficient to state that the airflow must be turbulent in the absence of methane. Fundamental work at SMRE on the behavior of methane roof layers has led to the formulation of rules for controlling methane roof layers which specify the ventilation velocity needed to ensure adequate mixing in terms of the rate of flow of methane into the layer (V = cu ft per min) and the airway width (D = ft). A "layering number" for methane and air has been defined by [U37/V/D] where U is the mean ventilation velocity in ft/min in the upper half of the airway. In a horizontal airway there is no mixing by turbulent diffusion for values of the layering number less than about 2, resulting in extensive roof layers. But with a layering number of 5, the layer is "brought under control"-i.e., a further increase in the layering number will shorten the length of the layer only slightly, and a small decrease in the layering number will cause only a small increase in the length of the layer. In a sloping roadway with uphill ventilation, higher values of the layering number are needed to achieve this "controlled" condition; the values range from about 5 at small slopes to about 8 at a slope of 1: 10. In downhill ventilation it is possible for layers to "back" against the ventilation, i.e., to flow uphill. The critical condition for preventing backing can also be expressed in terms of the layering number. Backing will be prevented if layering numbers are about 3 for small slopes and about 4.5 for large slopes; these values for downhill ventilation also give good control of the layer.

Jan 10, 1962

By Arthur F. Wendt

The hot-blast oven of which the accompanying plate gives complete details, was designed by the writer for the spiegel-furnace of the Lehigh Zinc and Iron Co., at Bethlehem, Pa. Members of the Institute who visit these works will have occasion to notice the large amount of zinc-dust in the gases, and the consequent dirtiness of both the hot-blast and the boilers. The zinc collects in a crust on the iron hot-blast pipes and leads to the frequent burning of them. A large vertical standing-pipe stove, a modification of the "Pleyer," thus gave considerable trouble by the burning of pipes and, on one occasion, the toppling over of a whole row. These inconveniences are avoided in the hanging-pipe stove under consideration, and less heating-surface has been found to be required to heat the blast to a given temperature. The construction of the stove is so simple and so plainly shown in the plate that it is needless to enlarge upon it. Each pipe rests in a box and is connected by U-branches with the next adjoining pipes. An iron sleeve is placed around the joint and tightened, as usual, with iron filings. In case of a pipe burning out, that particular section is cut off by the valves and the sleeves are broken. The pipe is then readily lifted out of the box and a new one is substituted. The whole operation requires only a short time and the section can then be at once put into use. The boxes supporting the pipes cover the whole surface of the hot-blast and are closed by iron covers rammed with fire-clay. Owing to the air-space around the U-pipes there is little loss of heat in the upper part of the stove. Each section as built has 280 square feet of heating-surface. The furnace is blown by a horizontal engine with 46-inch stroke and 48-inch diameter of blowing-tube. At 28 to 30 revolutions, the engine delivers 3000 cubic feet of air per minute, at a pressure of 5 pounds. When five sections of stove are in use, the blast enters the furnace at a temperature of 850" F. That is, there are over two cubic feet of air per square foot of heating-surface heated to that temperature per minute.

Jan 1, 1887

Jan 1, 1949