Search Documents

[Abrahamson, Guy C., (5'43) 1st Lt., A.C., 0-880861, Base Weather Sta., Fairfeld-Suisun AAB, Suisun, Calif. Adam, Howard Wilbur, (S'46) 45 Eaton Ave., Woburn, Mass. Aguilar, Ruperto G., (S'43) Texas College of Mines, El Paso, Texas. Ainge, Ronald Farra, (S'43) Otago University, Dunedin, New Zealand. Albala, Américo, (S'44) Casilla 4106, Santiago, Chile. Albrecht, Theodore J„ (S'42) Pfc., Co. F, Syme Hall, Rm. 1, SCU 3421, ASTP, N. C. State College, Raleigh, N. C. Aldridge, E. E., Jr., (S'39) Box 58, Eagle Pass, Texas. Alfred, Robert M., (S'40) 25 South St., Brighton, Mass. Allan, Douglas H. W., (S'40) 460 Main St., E., Hamilton. Ont.. Canada.]

Jan 1, 1946

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Bruno V. E. Nordberg

Hoisting is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.' In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michigan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualistic types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By Bruno V. E. Nordberg

Hoisting is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.' In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michigan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualistic types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By S. R. Balajee, I. Iwasaki

The adsorption mechanism of corn starch and its derivatives at mineral-solution interfaces was investigated by the adsorption of cationic starch, unmodified corn starch, British Gum 9084, and anionic starch on quartz and hematite. The adsorption of these starches, which decreases in the order mentioned, is dependent on the balance between the magnitude of the electrostatic interaction and the magnitude of the hydrogen bonding. There exists a critical starch concentration for both optimum flotation and flocculation conditions of iron ores, which corresponds to a point where the starch adsorption reaches a saturation coverage. Flocculation occurs due to the adsorption of starch via electrostatic and hydrogen-bonding forces and by interparticle bridging as a result of the conformation of starch molecules at the interface. The depressant property of starches and starch derivatives in flotation' and their flocculation char: acteristics in clarification and filtration2.3 have long been recognized on a wide variety of ores. The effectiveness of a starch as a depressant for iron minerals has been the subject of much investigation in recent years both in the amine flotation of siliceous gangue and in the anionic flotation of activated silica from iron ores. It has been reported that the depressant activity of starches and dextrins in the cationic flotation of quartz from hematite increases with molecular weight, branching, and number of hydroxyl groups, 1 and that the selectivity is affected by changing the configuration of starch molecules and the composition of its polar groups.4 ,5 The manner in which starches are solubilized was shown to exert a significant influence as a depressant in the anionic silica flotation, and a series of articles covering the practical aspects of flotation and flocculation have already been reported.618 Chemical modification of the starch structure, the pulp pH, the calcium ion, and the residual starch concentration were identified as some of the more important variables affecting the flotation behavior. In the flocculation of iron ores, it was noted that most starches flocculated suspensions of hematite in water but did not flocculate similar suspensions of quartz,9 and that an excessive use of starch restabilized the suspensions due presumably to protective action. 6 An admirable application of such an observation to practice may be cited in the selective flocculation and desliming in the anionic silica flotation of iron ores, which resulted in superior metallurgy and lower reagent cost. 10 From detailed adsorption measurements, Schulz'and Cooke4 established that the adsorption of starches and their derivatives depended on the types of minerals and of starches, pH, and electrolytes present. Their adsorption data and the foregoing flotation and flocculation observations suggested that an electrical interaction between starches and charged mineral surfaces might be playing a role in their adsorption process. Adsorption of organic polymers, particularly of synthetic origin, at solid-liquid interfaces has been extensively studied in recent years,' and it is realized that their adsorption mechanism is considerably more complex than that of simple ions or molecules. A polymer molecule possesses a number of functional groups, and the adsorption at a point may restrict the adsorbability of adjacent groups. The mechanism may be further complicated by the conformation of the polymer molecules which may exist as coiled spheres, helices, or extended chains as a result of intramolecular interactions among functional groups as well as intermolecular interactions with solvent molecules. The object of the present investigation was to examine the effect of the chemical modification on the adsorption characteristics of starches and starch products on quartz and hematite at several pH values, so that by correlating this information with flocculation and flotation results, adsorption mechanism of starches on mineral-solution interface may be elucidated. EXPERIMENTAL MATERIALS Quartz: St. Peter sand was screened at 35 mesh and the undersize was scrubbed and deslimed at a Fagergren cell. The deslimed sand was cleaned with 0.1 N hot hydrochloric acid and washed repeatedly with distilled water, For anuscript, measurementsl the -200-mesh fraction of the sand was ground dry in a porcelain mill for 3 hr. The specific surface of the finely ground quartz was

Jan 1, 1970

By Walter Renton Ingalls

Vague references to tin-deposits in Mexico are scattered throughout technical literature, and that country has been looked to as a likely source of a part of the world's supply of till at no very distant date; but thus far nothing but occasional small lots have come forward, so that the notion has arisen that these mines are either mythical or unworkable. So far as I am aware, there has not yet been published any description of the tin-deposits of Mexico except a few brief references; and this paper, based on a study of them made in 1892, is therefore offered.

Jan 1, 1896

By F. W. Luerssen, J. F. Elliott

F LUSHING the early slag from a stationary open Fhearth having a high percentage of hot metal in its charge is necessary in order to remove silica from the system. The flush slag is strongly oxidizing and is somewhat acidic. It has, however, considerable capacity to extract phosphorus from the bath and it also removes considerable manganese. It seems probable that factors which control the distribution of phosphorus and manganese between slag and metal in the refining period also should be dominant in the flush and postflush periods. Several studies, as summarized elsewhere,1,2 support the viewpoint that conditions closely approaching equilibrium for these elements are rather readily established during the refining period. Over the years these studies have repeatedly demonstrated that 1—high slag v01ume, 2—low bath and slag temperature, 3—basic slag, and 4—strongly oxidizing slag favor rapid elimination of phosphorus from the bath to the slag. They also show that the following conditions favor retention of manganese in the bath: 1—low slag volume, 2—high bath and slag temperature, 3— basic slag, and 4—minimum oxidizing power of slag. When it is considered that the flush slag often carries as high as 75 pct of the manganese charged and only 25 to 60 pct of the phosphorus charged, it is evident that in removing silica much manganese is sacrificed but phosphorus removal is far from conplete. Because of overriding circumstances, this is accepted in most operations and actually it is considered to be inevitable. This may account for the fact that little attention has been paid to conditions affecting the elimination of phosphorus and manganese in the flush slag. A recent study of the behavior of various charge oxides has developed considerable information on the flush and postflush periods. Because the data are felt to be of general interest, they have been brought together and Presented in this paper. The object is to show the various factors in the flush and postflush periods which influence elimination of phosphorus and manganese. Physical Conditions During and After Flushing Physical conditions existing during the flush vary from plant to plant, from shop to shop, from furnace to furnace, and even from heat to heat. They are strongly influenced by the physical and chemical character of the charge oxide which is ordinarily necessary to provide sufficient oxidizing power early in the heat. Invariably the period is characterized by a vigorous reaction between the principal re-actants: the hot metal being added and the charge oxide. During the flush, it is probable that the slag acts to some extent as an oxidizer; but, because of the critical influence of the behavior of the charge oxid'e on flushing action, it seems apparent that the oxide itself is the dominant oxidizer. Fig. 1 shows the course of two heats which were selected as being typical of the group studied. Heat A was charged with 55 pet hot metal, based on the total metallics charged, and heat B had 57 pct hot metal. As indicated in Table I and Fig. 1, the melt-down slag, which is not usually voluminous and which is principally FeO, expands greatly in volume and will show rather high levels of SiO2, MnO, and P2O5 very soon after the beginning of the hot metal addition. Simultaneously, large volumes of CO are liberated which cause violent mixing of slag and metal. It is of interest to note that the time required to bring carbon down to a low level is very much longer than that required for the removal of silicon, manganese, or phosphorus. At the end of flush, carbon in the bath is still approximately 2 pct. When strongly reducing hot metal is brought into contact with strongly oxidizing conditions within the furnace! it is probable that the rate of mass transfer to the slag (and atmosphere) of silicon, manganese, phosphorus, and carbon initially depends principally on the rates at which the two participating phases are brought into contact That is, it depends on the nature of the various reactions. Later in the flush period, when the scrap is virtually all dissolved and the action of the bath has settled down to a steady and somewhat gentle boil, it is likely that other factors, such as the transfer of oxygen across the slag-metal interface, become dominant. The temperature of the slag-metal system is far from uniform. Heat is being driven by the flame down through the slag. Bubbling and surging of the metal also frequently brings portions of the bath in contact with the flame. At areas of contact between the ore and liquid metal, or slag and liquid metal, the oxidizing reactions generate much heat. On the other hand, scrap is being melted which tends to absorb large quantities of heat. Because the liquid bath is high in carbon, the steel scrap is brought into solution rapidly. This can proceed at a rather low temperature; and until much of the scrap has been taken into solution, the bath temperature would not be expected to increase appreciably. Consideration of these factors leads to the conclusion that during the flush period the slag should be rather hot and the bath relatively cold. Both observation and temperature measurements bear this out. Experimental Data The extended program of charge oxide evaluation permitted study of the widely varying conditions existing during the flushing period. Slag and metal analyses and bath temperatures reported herein (Tables I and 11) were obtained toward the latter portion of the work. Four different types of charge oxide, sinter, two types of hydraulic cement-bonded soft ores, and a pyrobonded agglomerate were used in the study. Although the heats reported were from only one 205 ton furnace, they show variations in flush slag analyses all the way from 25 pct FeO, which is typical with the use of a hard natural charge ore, to 45 pct FeO which resulted when a very poorly agglomerated fine ore was used. The physical behavior of the flushes showed a correspondingly wide variation from well controlled reactions to violent surges following periods of inac-

Jan 1, 1956

By W. C. Shanks

Seventeen deeps, which contain hot or cold brines and/or metalliferous sediments, have been discovered in the axial rift zone of the Red Sea. Metalliferous activity results from the unique geological setting of this incipient ocean basin: oceanic crust intruding in a central rift zone flanked by thick evaporite sequences. Brine pools tend to occur in structural depressions where- transform faults intersect the spreading axis. The most significant metalliferous occurrence is in the Atlantis II Deep, which contains approximately 227 Mt (dry weight) of metalliferous sediment which averages 1.04% Zn and 0.28% Cu. Higher potentially economic grades (3-6% Zn, 1% Cu, 50 glt Ag) occur in the Southwest Basin of the Atlantis II Deep, comprising total metal tonnages of 1.7 Mt Zn, 0.4 Mt Cu, and 5000 t Ag. The Pre-Pilot Mining Test conducted in 1979 raised 15 000 m3 of mud by a slurry process and demonstrated the feasibility of mining, concentration by froth flotation, and tailings disposal at sea. A Pilot Mining Test is scheduled for 1983-1984. The metalliferous discoveries in the Red Sea provide a model example of deep marine mineral exploration. Detailed mapping of bottom bathymetry and brine-interface reflectors using a high-resolution narrow-beam echo sounder has been the most effective exploration tool in the Red Sea. Followup coring has discovered additional metalliferous deposits in basins without present-day brines, and potential exists for additional discoveries. Geochemical exploration using heavy metals values in sediments (iron, manganese, zinc, copper, and mercury) and sulfur isotope values of sulfides are considered to be the most promising techniques for discovery of currently inactive deposits. Positive sulfur isotope values in the range I to 17 are an indication of hydrothermal sulfides in the Red Sea, and there is considerable contrast from back- ground bacteriogenic sulfides ( - 10 to - 45).

Jan 1, 1983

At the request of representatives of the Treasury Department, President Winchell appointed the following committee, which .held a two-day conference with the Treasury representatives in Washington Oil Oct. 6 and 7 to aid in deciding upon the principles of mine taxation to he adopted by the Government. The results of this conference, which is not yet concluded, will be published in a future Bulletin.

Jan 11, 1919

By Louis Stott

IT is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halske6 reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys.

Jan 1, 1936

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, yet in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has been mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been al most entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is amazing that the iron companies will persist in sending abroad under. heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below-will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests were conducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color .to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition Water, - 2.68 Silica, - 65.46 Iron oxide, - 2.10 Alumina, - 15.02 Magnesia, - 15.35 100.61

Jan 1, 1882

By B. E. Eakin, R. T. Ellington

An apparatus and a procedure for determining the viscosity behavior of hydrocarbons at pressures up to 10,000 psia and temperatures between 77 and 400° F are described. The equipment is suitable for measuring viscosity of either the liquid or vapor phases or the fluid above the two-phase envelope for systems exhihiting retrograde phenomena, according no the phase state of the system within these ranges of temperature and pressure. Equations are developed for calculation of viscosity from the experimental measurements, and new data for the viscosities of ethane and propane at 77° F are reported. INTRODUCTION With the advent of higher pressures and temperatures in industrial processes and deep petroleum and natural gas reservoirs, demand has increased for accurate values of physical properties of hydrocarbons under these conditions. Proportionately, more frequent occurrence of natural gas and condensate-type fluids is encountered as fluid hydrocarbons are discovered at greater depths. This increases the importance, to the reservoir engineer, of being able to predict accurately the physical properties of light hydrocarbon systems in the dense-gas and light-liquid phase states. Reliable gas viscosity data are limited primarily to measurements made on pure components near ambient temperature and at low pressures. Few investigations have been reported for high pressures, and except for methane, data on light hydrocarbons are subject to question. This is demonstrated by the large discrepancy between sets of data on the same component reported by different investigators. For mixtures in the dense gas and light liquid regions and for fluids exhibiting retrograde behavior there are very few published experimental data. Viscosity data for methane have been reported by Bicher and Katz,1 Sage and Lacey,12 Comings, et al,3 Golubev,3 and Carr,3 with good agreement among the last three sets of data. Comings, Golubev and Carr utilized capillary tube instruments for which the theory of fluid flow is well established. The theory permits calculation of the viscosity directly from the experi- mental data and dimensions of the instrument alone. Sage and Lacey, and Bicher and Katz used rolling-ball viscometers. The theory of the rolling-ball viscometer has not been completely established, and these instruments presently require calibration by use of fluids of known viscosity behavior before viscosities of test fluids can be measured. To obtain accurate data it is necessary that the rolling-ball viscometers be calibrated by use of fluids of density and viscosity similar to the test fluids, a difficult selection for the gas phase. From the methane data and experimental tests on various natural gases, Carr developed a correlation for predicting the PVT behavior of light natural gases.2,3,4 This correlation was based on data for a very limited composition range; its application to rich gases and condensate fluids is questionable. The object of this investigation is to develop an instrument which can be used to obtain viscosity data at reservoir temperatures and pressures, for rich gases, condensate-type systems above the two-phase envelope and light liquid mixtures. These data will be used in an effort to develop correlations to represent the viscosity behavior of these fluids. APPARATUS In a previous viscosity study Carr2 utilized a modified Rankine capillary viscometer configuration," Fig. 1. In this instrument the gas to be tested is forced through the capillary tube in laminar flow by motion of a mercury pellet in the fall tube, the measured displacement time being that required for the mercury slug to move between the brass timer rings. The viscometer is constructed of glass and mounted in a steel pressure vessel. The test gas pressure in the viscometer is balanced by an inert gas (usually nitrogen) in the vessel. Excellent results have been obtained with instruments of this type, with Carr2 and Comings5 reporting repro-ducibilities of 99.5 to 99.3 per cent and an estimated absolute accuracy of 99 per cent. However, these instruments have limitations which have precluded their use for liquids. The need for maintaining a balance between pressures of the test fluid and inert gas in the viscometer vessel presents operating problems, and requires charging the test fluid to the viscometer very slowly. The principle drawback to the Rankine unit is behavior of the mercury slug which provides the pressure differential across the capillary. When even trace quantities of propane or heavier hydrocarbons are present in the test gas, the mercury tends to subdivide

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C'. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h'b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,' by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K' is the value for the Fe-S binary solution. and the limiting value of K' in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1' that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

IT is necessary that all men who wish to bring things to a certain end should think of the agents needed to attain this. Now whichever one of the above processes you wish to use you must consider the nature of the material and see whether it is disposed to render what you wish to extract. Then you must see whether you have the other agents sufficiently powerful and proportioned to attain this result, for if the things were not in harmony your work would be vain and very laborious. Therefore, if you should wish to make waters or oils by way of distilla-

Jan 1, 1942

By J. C. Sullivan, W. A. Knoll

THE sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In November of 1930, experimental work was con- ducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4%-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. DRILLING Air was carried down the shaft in an 8-in. flanged pipe line at a pres- sure ranging from 95 to 100 lb. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1938

By Sidney A. Swensrud

This paper reviews the subject of gasoline margins, discusses some of the more current marketing problems, and gives some consideration to the main urges to marketing expansion, or overexpansion, in the oil industry. Margins In an earlier paper1, some comparisons were shown for the years 1929, 1930 and 1931, of the margin between the refinery cost of gasoline in Oklahoma, the market price in Oklahoma, and the average retail price in 50 representative cities of the United States. These figures indicated a small margin for the refiner in 1929 between his gasoline cost and the wholesale price, which, however, had turned into a loss by 1931. The margin between either refinery costs or wholesale prices and the retail price in the 50 cities showed a continuous decline during the three years. We have now worked out these figures on a similar basis for a longer period—from 1928 through 1936. The figures for refinery gasoline cost are slightly different from those in the earlier study, owing to the use of

Jan 1, 1937

By Yap Chu-Phay

IN the previous paper, the writer showed how, on the basis of thermodynamic reasoning, it seems probable that when true equilibrium conditions obtain, carbon exists as Fe3C in the liquid state and as elementary carbon in the solid state (7 Fe), in which case the solidus would be a straight line from 0.18 to 1.70 per cent. carbon (Fig. 1). In the same paper he concluded that the solidus obtained by Honda 'and his co-workers1 probably does not represent the same conditions, insuring a complete equilibrium. Except for a downward temperature displacement, the solidus obtained by Gutowsky,2 using the Heycock and Neville method, practically coincides with Honda's solidus as shown in Fig. 1. The writer at first thought that perhaps in some way Gutowsky's thermocouple was improperly calibrated for high-temperature measurements, as his liquidus was also much lower than those obtained by Carpenter and Keeling3 and by Ruer and Goerens.4 However, the eutectic temperature obtained by Gutowsky agrees with the generally accepted value of 1130° C., so that the validity of the inference regarding improper temperature calibrations is to be strongly doubted. In Fig. 1, Gutowsky's solidus is shown both in the original and in the corrected form. In the latter, a correction of 29.2° C. is made for all temperatures above 1416° C. in accordance with-

Jan 1, 1931

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957

By T. B. Counselman

AN iron blast furnace of 1000 tons daily capacity will produce about 100,000 cu; ft. per minute of blast-furnace gas. This contains about 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. This gas-is used primarily for heating the stoves of the blast furnace, and secondarily, under boilers, for steam production. Occasionally it is also used in gas engines. The raw gas coming out of the furnace carries about 10 grains of flue dust per cubic foot of gas, under best operating conditions. With the furnace "rolling" or slipping, this quantity may temporarily be greatly increased. This dust would, of course, deposit on the checkers of the stoves, or plug the burners under the boilers; therefore the gas must be cleaned.

Jan 1, 1936