Search Documents

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By E. W. Mehal, R. W. Haisty, D. W. Show

The next generation of integrated circuits will probably include circuits constructed in and of GaAs. The existence of both semi-insulating and semiconducting forms of GaAs is the fact which will bring this about. In this paper we discuss the uses and limitations of semi-insulating GaAs for integrated-circuit applications. The two main areas considered are the electrical isolation that can be achieved between components on a semi-insulating substrate and the characteristics of p-n junctions in contact with semi-insulating GclAs. A process basic to attaining integrated circuits in GaAs to fully utilize the insulating properties of the substrate is selective epitaxial deposition. This process involves the deposition of a SiO2 layer onto a The trend in integrated circuits is towards the use of high-resistivity substrates or regions to achieve component isolation. The use of SiO, layers in the oxide isolation methods and the use of sapphire substrates are examples of this idea. GaAs is also a polished surface of a GaAs substrate, etching out selected area of the SiO, film to expose a GaAs surface, and deposition only onto the exposed GaAs surface. By using this process , islands of semiconducting GaAs are deposited onto a semi-insulating GnAs substrate, the islands being electrically isolated from one another by the substrate. The deposition of both p- and n-type semiconducting GaAs can be carried out in this nzanner to form p-n junctions in the island areas. This process can also be used to produce a planav structure by deposition of GctAs through a SiO, mask into holes etched into the GaAs substrate. This Putterned Epitaxial Technology (PET) is described. very promising material for use in future integrated circuits because of the existence of both semi-in-sulating and semiconducting forms. Active devices can be fabricated in the semiconducting material, and these individual components can then be electrically isolated from one another by using semi-insulating GaAs as the substrate. Epitaxial semi-insulating GaAs can also be produced thus making three-dimensional monolithic integrated circuits feasible.' This paper describes the research aimed at developing the methods for producing both two- and three-dimensional integrated circuits in GaAs, and examines some of the properties of semi-insulating GaAs as they relate to these integrated circuits.

Jan 1, 1967

By Frank Firmstone

IN April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Fig's. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised to¬gether, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places. * Etudes our lea Haut Fourneaux, page 108.

Jan 1, 1874

By AIME AIME

This volume, in the preparation of which all former annual or collective indexes have been not only compiled but revised, is published for the special benefit of all who do not possess complete sets of the Transactions. And it is published at this particular time, as part of a plan by which it is hoped that the Library of the Institute, which, through liberal donations, has become unexpectedly comprehensive and valuable, may be made useful throughout the world. Thus, any person possessing this Index can ascertain at once what has been published in the Transactions on a given question, and can learn, by writing to the Secretary, what is its nature, whether it is still to be had in pamphlet form, where it can be consulted in a public library, at what cost it can be copied by hand, etc., etc. In short, to those who own complete sets of the Transactions, this Index will be a great convenience; but to those who do not, it will be a professional necessity. The edition now in press is limited, and orders received will be supplied according to date.

Jul 1, 1907

By H. O. Hofman

Discussion of the paper of H. O. HOFMAN and JOHN BLATCHFORD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1915, pp. 91 to 97. ROBERT H. RICHARDS, Boston, Mass.-I should like to ask Professor Hofman whether he is able to roast his stibnite without any comparatively large amount of loss of antimony? H. O. HOFMAN, Boston, Mass.-Yes. The last statement I made was that the loss of antimony, during those tests, increased with the temperature, and that up to 372° C. there was no loss whatever in antimony, also that it increased to 4:2I per cent. with 545° C., the highest temperature that we obtained in our small furnace. ROBERT H. RICHARDS.-I should like to ask a second question, and that is, is it not true that stibnite can be roasted more completely than any other sulphide?

Jan 5, 1916

The President was authorized to appoint. a liaison committee to cooperate with the American Mining Congress in respect to the establishment of a Secretary of Mines and Mining in the President's Cabinet. He appointed Edwin Ludlow, Chairman; Mark L. Requa, and J. E. Johnson, Jr. It was resolved to accept the invitation from the Chicago Section to hold the. 120th meeting of the Institute in Chicago during the week of Sept. 15, 1919. The action of the Executive Committee in appointing Past President E. Gybbon Spilsbury as representative of this Institute to visit France upon the invitation of the Société des Ingénieurs Civils de France was approved. The final budget for 1918 was approved. Tile President was authorized to appoint a committee, of three members, on the Development of Activities of the Institute. The committee was requested to report at the February meeting of the Institute, and the Secretary was requested to invite each local section to have a member present to discuss the subject. The President appointed J. W. Richards, Chairman; P. N. Moore, and Allen H. Rogers. Thirty-six members, ten associates, and five junior associates were elected; one change of status from associate to member was granted; two members were reinstated; and eight resignations were accepted. An extension of time was granted to nine members. The dues of eight members were suspended on account of their being in active service.

Jan 2, 1919

By Ralph H. Sweetser

BENEFICIATION of iron ores from the blast-furnace point of view means more than the usual enrichment of the iron contents by the removal of a large part of the clay, carbonic acid gas, silica, or moisture of the natural ore; it includes all these, but it also embraces several other mechanical .processes made , necessary by the exacting requirements of present-day blast-furnace practice. The increasing use of iron- bearing by-products, to as much as a third or more of the total ore burden, has introduced still another series of processes for improving the blast-furnace ore burden. As we look back over the past three decades of blast- furnace practice 'in. this country, we see that many of the blast-furnace troubles were directly due to lack of proper preparation of the iron ore burden,, and we realize that beneficiation in one form or another would have remedied the trouble. This was particularly true in the smelting of magnetic iron ores, where run-of- mine ore included such big lumps of 'magnetite along with rich fines that the furnace operations were greatly retarded and control of the furnace such as is usual today, was completely unknown.

Jan 1, 1930

By Jei Y. Choi, P. G. Shewmon

The surfrrce-diffusion coefficients (DJ for Aulg8 on (100) and (111) surfaces of copper have been determined between 1050" and 780°C using a new avuzlysis imd experimental procedure. The results are: D, has also been determined fm cua4 at 870°C, and the values found are 4.5 times larger than those measured by the grain boundary grooving technique for the same surface orientations. This difference is felt to result from the approximate nature of the mathematical solution used in the present work. Attempts to measure D, for silver on copper and silver surfaces indicated a means of matter transport different from surface diffision was dominant in moving tracer from the source out over the surface. Cnlculations and experiment both indicate that this is the flow of silver through the vapor phase which completely masks the much smaller flow due to surface diffusion. The previous self-difhsion studies of D, for silver and copper are discussed in terms of our own analysis and found to yield values of D, factors of lo5 or more greater than those found by the grain boundary grooving tech -nique. UNTIL about 5 years ago it was widely believed that the activation energy for surface diffusion, AH, , was less than that for grain boundary diffusion, AHb,, which in turn was less than that for diffusion through the lattice, AHz.' This was concluded from various evidence that D,> Db>Dl, and one tracer study of D, for silver on silver from which AH, was inferred.2 In 1959 Mullins and Shewmon demonstrated that D, could be determined from the kinetics of the growth of grain-boundary grooves.3 Using this procedure, Gjostein measured D, on copper between 800" and 1050°C and found that the activation energy was roughly equal to AHl .4 Subsequent work on copper,5" silver,',' and goldg between the melting temperature T, and 0.87 T, confirmed that AH, as determined using the grain boundary grooving or scratch-relaxation technique was equal to or greater than AHz. During the same period, Drew and Pye again determined AH, for silver on silver using a tracer techniquelo and a mathematical solution similar to that of Nicker son and arker.' Though the values of D, Drew and Pye measured at any given temperature were about 200 times smaller than those reported by Nickerson and Parker, they again found a low activation energy of about 10 kcal, or about one fifth that found at the higher temperatures with the mass transport technique. A distinguishing characteristic of these two previous tracer studies is that they have worked at low temperatures (-1/2 T,) where they felt volume diffusion was negligible and then analyzed these data as if all tracer atoms leaving the source flowed out into and remained in a homogeneous high-diffusivity surface layer of undefined thickness. This is totally different from the model used in the mass-transport studies or the studies of grain boundary diffusion, which assume the high-diffusivity surface layer to be only a few angstroms thick. If this latter model is applied to the earlier tracer studies, it is shown that the tracer has really pe!etrated into the lattice a mean distance of 1000A. Thus the tracer distribution observed after an anneal is thought to be due to the combined effects of surface and volume diffusion. Independent of the relative validity of the two models, it seems evident to us that any comparison of the values of D, as determined in these two ways is meaningless and misleading, since the values of D, and AH, obtained in these two ways would be totally different for the same physical distributions of tracer. Once the fundamental difference in the approaches of the two techniques is established, we are faced with the question of which model better approximates physical reality. Here all the evidence seems to be on the side of the ''thin surface layer" analysis. In fact, the authors of Refs. 2 and 9 do not argue for the "thick-layer model" we have described; they simply invoke it through the equation they use to calculate D, . The primary evidence for the thin-film approach is: a) grain boundary grooves and scratches widen in proportion to tU4 and Mullins' rigorous analysis shows that this is only valid for a surface layer which is quite thin relative to the width of the groove;11 b) all accepted or seriously discussed models of solid-vapor interfaces and high-angle grain boundaries assume that the disturbed region of the interface is at most a few a0 thick. With the above in mind, it was desirable to determine D, using a radioactive tracer and a "thin-

Jan 1, 1964

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By Ali M. Heidarieh Zadeh, Raghu N. Singh

The paper presents a stability investigation of shaft intersections and pit bottom roadways in the vicinity of upcast and downcast shafts at a colliery in the U.K. Aschemeof instrumentation was aimed at monitoring the strata displacement surrounding the pit bottom roadways and shaft intersections with a view to ascertaining the origin of the strata movement and effectiveness of the control measures. The bore- hole instrumentation results together with a theoretical analysis suggested that the cause of instability could be attributed to the drivage of a roadway within the shaft pillar. A semi-empirical technique was used to calculate the amount of support resistance required to reinforce the pillar to take additional abutment load. A rock bolting system was designed to provide a required increase in thrust capacity of the roadway support. The results indicated that roadway closure was effectively controlled after installation of bolts indicating efficacy of the control measures adopted.

Jan 1, 1982

Jan 1, 1919

William H. Blauvelt, Syracuse, N. Y.:—Is the coal itself from which the briquettes are made of good quality for steam-ing-purposes? Mr. Parker :—It is an anthracite coal mined near Bank-head arid used on the Canadian Pacific railroad. It contains about 83 of carbon, 8 of ash, and 8 per cent. of volatile material. With regard to briquetting of a mixture of fine coal and coke-dust, I understand that a plant has been installed near Detroit in which coke is mixed with anthracite; also the plant of the United Gas Improvement Co. near Philadelphia is briquetting a mixture of anthracite coal, the resultant briquettes being used in the gas-retorts. Mr. Blauvelt:—The purpose of the Detroit briquette-plant of the Solvay Process Co. has been partly to use up the coke-breeze from the by-product ovens and partly to utilize the pitch. There is no necessity for mixing anthracite with the coke-breeze, but the supply of breeze is limited, and anthracite

Jan 1, 1909

By F. W. Jessen

The Mechanism of solution of salt and mixed halites of sodium and potassium is reviewed. The variation in the rate of salt removal under both laminar and turbulent flow conditions is discussed. Many changes are possible in the development of solution cavities whether used for production of salts or for storage of hydrocarbons. The parameters influencing the type and shape of cavity formed with single well or multiple well systems are examined and information presented regarding field application of techniques developed and the means of controlling overall configuration of solution cavities.

Jan 1, 1972

By F. A., King

THE problem of the proper size and capacity of the open-hearth furnace has been a predominant issue ever since its inception some sixty years ago. The original furnaces, built in 1868 at Landore, England, were only to 3 to 4 tons capacity, and from' this there has been a steadily increasing and almost uniform rate of expansion until furnaces producing 300 tons are in successful operation today. At the end of the first half of this 60-year period, or about the year 1900, 50-ton furnaces we're common. Up to this time the problems of expansion had been largely those relating to suficient capital and the engineering development of larger units. But as 75, 100-ton and larger furnaces were proposed apprehension grew and other questions assumed leading consideration.

Jan 1, 1928

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping'' action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett's' survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,' Ruddle,' and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.' These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,' and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,' Gronningsater and Drummond," Ruddle,' Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By George R. St. Pierre, John Chipman

METALLURGISTS have been studying the chem-ical behavior of sulfur in steelmaking for many years in order to have a better control of the sulfur content of finished steel. During the refining period in the open hearth, molten steel is separated from a gas phase by molten slag. Chemical reactions occur principally at the slag-metal interface and at the slag-gas interface. A need for physical-chemical investigations of reactions between sulfur-bearing gases and steelmaking slags was recognized some time ago.'.' From the early work, it can be qualitatively concluded that increased sulfur content and low partial pressure of oxygen in the gas phase favor the passage of sulfur from gas to slag. Using radioactive sulfur S Koch and Fink' have demonstrated the rapid rate of exchange of sulfur between gas and slag in an open hearth furnace. Gurry and Darken and Darken and Shields (as reported by Derge and Marshall') have equilibrated lime-iron oxide slags with SO—O2 gas mixtures. The major conclusion from the reported results is that sulfur content increases with increasing lime content in lime-iron oxide slags equilibrated with a gas of high oxygen pressure (10-2). The data were interpreted as indicating the presence of SO, and S,O, ions. Richardson and Fincham' have conducted the most extensive experimental study of sulfur equilibria between gas and slag. Their results confirmed many of the conclusions drawn from calculations of Richardson" and Withers. Richardson and Fincham's data fitted very well into the sulfur scheme represented by the reactions 1/2 s2 (g) + (0) melt - 1/202(g)+ (S) melt [II 1/2 S, (g) + 3/2 O (g) + (0) melt - (SO,) melt. [2] At oxygen pressures greater than 10 to 10 they found that reaction Eq. 2 was predominant while reaction Eq. 1 was controlling at oxygen pressures less than 10." to 10.". The slag compositions and gas mixtures used in their investigations were different from those used in the present study. Wherever possible, comparison has been made between their results and these, and agreement is excellent. It is evident that the distribution of sulfur between slag and gas depends upon the oxygen pressure of the gas. In FeO slags, a change in oxygen pressure produces a change in ferric oxide content, and a knowledge of this equilibrium is a prerequisite to studies of sulfur distribution. The data are found in the work of Darken and Gurry" on the FeO system and the more recent experiments of Gurry and Darken" and of Larson and Chipman" on FeO slags containing lime and silica. The effect of oxygen pressure on the ratio Fe /(Fe" + Fe ), the so-called j-ratio, reported by these investigators will be used in interpreting the results which follow. Experimental Method The purpose of the experimental program was to determine the equilibrium sulfur content in slags exposed to gases of known oxygen and sulfur pres- sures. The slag compositions selected for study were from the lime-silica-iron oxide system. Additions of magnesia were made to some of the slags. Apparatus—The apparatus used by Larson and Chipman was modified slightly to accommodate the addition of SO2 to the gas mixtures. As in their work, slag samples of 0.5 to 2.0 g were held at temperature (lcc) in platinum crucibles under a steady stream of gas, 100 to 200 ml per min, for several hours and then rapidly lowered to the bottom of the furnace where they were quenched in mercury. Preparation and Analysis of Gas Mixtures—Mixtures of SO,-CO were prepared from Virginia Smelting Co. Extra Dry liquid SO, and Pure Co. CO,. After removing traces of water vapor with an-hydrone, the CO, was passed over graphite at 1200°C, at which temperature the conversion to

Jan 1, 1957

By D. W. White

The kinetics of isothermal transformation of ß-to-u uranium have been studied over a broad temperature range in alloys containing from 0.3 to 4.0 atomic pct Cr. Two modes of transformation are indicated by the existence of two C-curves in the TTT diagram. The upper temperature mode is regarded as a nucleation and growth mechanism, whose rate is controlled by diffusion of chromium in the ß phase matrix. The lower temperature mode is martensitic in nature. The M, temperature increases with decreasing chromium content, suggesting that the two transformation processes become synonymous in unalloyed uranium. URANIUM metal undergoes two allotropic transformations in the solid state. The a phase, orthorhombic in crystal structure,' is stable from room temperature up to about 665°C. The ß phase, characterized by a complex tetragonal structure,' prevails from 665" to about 770°C. The y phase is body-centered-cubic3 and is the stable modification from 770°C up to the melting point (about 1130"). In uranium of reasonable purity, neither of the two high temperature phases can be retained by quenching. However, the addition of certain alloying elements to uranium makes it possible to retain either the y-uranium phase or the ß-uranium phase at room temperature. Chromium alloyed in small amounts with uranium will permit retention of the ß-uranium phase in a metastable state at room temperature upon quenching from a ß-phase temperature.' From available information' on the equilibrium phase diagram for the U-Cr alloy system (Fig. I), it is to be expected that, however sluggish in its rate, the ß phase in such alloys should decompose eutectoidally to a phase and elemental chromium. It was the aim of this investigation to measure the rate and study the nature of this decomposition as a function of temperature and of chromium content. The investigation was reported in classified literature about five years ago and has recently been declassified for publication. In the meantime, there have appeared the papers of Holden,5 Mott and Haines,".' and Butcher and Rowe8 ealing with the metallography and the crystallography of the ß-to-a transformation in U-Cr alloys. These investigators have confirmed several of the phenomenological observations that will be described in the present paper and have examined in considerable detail certain aspects of the transformation and its mechanism. Although all of these investigations have concerned themselves experimentally with U-Cr alloys for the most part, an important consequence has been a clearer understanding of the nature of the ß-to-a transformation in uranium metal itself. Experimental Procedure This investigation dealt with a series of uranium alloys varying in chromium content from 0.3 to 4.0 atomic pct (0.066 to 0.90 weight pct). On five of the alloys, rates of isothermal transformation from the ß to the a phase were measured over a wide temperature range, leading to the development of TTT (time-temperature-transformation) diagrams. Transformation rates were measured over certain narrow temperature ranges on additional alloys. The alloys were prepared by vacuum melting and casting, using zircon or magnesia crucibles and graphite molds. Electrolytic chromium was used as the alloying addition, and the uranium was Mallin-ckrodt biscuit metal that had been vacuum remelted and cropped to remove many of the nonmetallic impurities that had floated to the top of the ingot. The ingots, 3/4 or 1 in. diam, were reduced in size by swaging. Alloys containing less than about 2 atomic pct Cr were swaged at 250° to 275°C, with initial and intermediate anneals at 550°C after every 75 pct reduction in area. Alloys with higher amounts of chromium were swaged at 550" to 600°C, although at the smaller sizes some of them were reduced by the procedure used on the more dilute alloys. Before use as test specimens, the swaged rods were annealed at 700" to 720°C for several hours, followed by slow furnace-cooling. The purpose of the anneal was to achieve the maximum amount of solution of the available chromium into the ß phase, as well as to remove extensive preferred orientation. The isothermal transformation rates were measured dilatometrically, using a quenching dilatometer and an experimental technique similar to those employed by Davenport and Bain in their original work on the transformation kinetics of austenite in

Jan 1, 1956

By S. H. McFarlane, K. H. Zaininger, G. W. Cullen, C. C. Wang, G. E. Gottlieb

Heteroepitaxy of silicon on stoichiometric spinel has been studied. Both boron-doped (p-type) and arsenic-doped (n-type) single-crystal silicon films have been grown by the pyrolysis of silane on sioichiometric spinel (MgAl2O4) substrates prepared by a flux technique. The spinel crystals are free from strain and subgrains, and exhibit no thermal instability at temperatures employed for silicon deposition. The growth parameters of epitaxial silicon have been studied. Effects of substrate orientation, surface preparation, and growth conditions on the silicon Properties have been determined. The silicon-spinel composite was characterized by X-ray diffraction, electron diffraction, electron microscopy, and optical techniques. Information on epitaxial orientation relationship, defect structures and film-substrate interface has been obtained. A parallel orientation relationship was found between silicon and spinel. The silicon films exhibit no subgrain structures. However, growth pyramids, microtwins, stacking faults, and dislocations are the prevalent defects. The deformation of epitaxial silicon was measured by an X-ray technique. It was found that the epitaxial silicon is strained under compres-sive stress due to the thermal expansion difference between the film and substrate. The stress was estimated using the classical plate theory and beam equation. Electrical properties of the epitaxial silicon have been measured, including resistivity, carrier concentration, and Hall mobility. MIS and vertical through diffused junction structures have been fabricated wing silicon-spinel composite. Information on MIS characteristics, minority carrier life time, and junction properties has been obtained. THE achievement of single-crystal growth of large area silicon semiconductor films on oxide insulating substrates is of technical importance to many solid state electronic devices. The semiconductor-insulator composite structure is also of scientific interest because the heteroepitaxy is determined by the spatial relationship between the atomic arrangement in the substrate and that of the atoms in the appropriate crystallographic plane of silicon. The degree of crystalline perfection of the silicon deposits depends also on the physical condition of substrate surface. Epitaxial growth of silicon on commercial flame fusion Al-rich spinel (MgO:3.3A12O3) has been reported by several investigators.'-4 The lattice of spinel of this composition is distorted. The material cracks and exsolves the excess alumina in the lattice at temperatures (-1200°C) used in fabricating silicon devices. Stoichiometric MgA12O4 spinel exhibits neither lattice distortion nor thermal instability. Results are given on the epitaxial growth and characterization of silicon on stoichiometric spinel. EXPERIMENTAL Fabrication of Silicon-Spinel Composite Structures. The MgA12O4 spinel substrate wafers were prepared from bulk single crystals grown at about 1200°C by a flux technique5 using a PbF2 flux. The crystals are free from strain and subgrains, and exhibit a typical dislocation density of less than 50 lines per sq cm. The crystals are thermally stable without cracking and exsolution of alumina to at least 1500°C. The spinel crystals were oriented for cutting by the Laue X-ray back-reflection method.6 Substrate wafers (about 25 mil thick) of (Ill), (loo), and (110) orientations have been obtained bu cutting the X-ray oriented crystals using a standard type diamond wheel. An accuracy of better than 1/2 deg is maintained throughout the operation. The spinel substrate wafers were mechanically lapped and polished to produce the flat and smooth surface which is required for silicon epitaxy. Lapping was carried out with about 30-µ boron carbide abrasives to obtain a flat coplanar surface. The lapped surface was further polished using successively finer grades of alumina, ending with the 0.3-µ grade. After polishing the wafers generally have a flatness of ±0.4 µ per cm, as revealed by interferometry. Fig. 1 shows (111) oriented MgA12O4 spinel wafers of various shapes.

Jan 1, 1970

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength-temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates. IN most routine experimental work on products and processes, method:; of operation and product evaluation are established from accurately controlled laboratory tests. With particular emphasis on the pelletization of fine iron ore concentrates, standardized procedures of laboratory production and product testing have been established at Cleveland-Cliffs Iron Co. Research Laboratory at Ishpeming, Mich. A program of this nature was used for investigating the agglomeration characteristics of various iron ore concentrates. The factors which control the process were studied and subsequently controlled for these investigations. Pelletizing as applied to iron ore agglomeration involves the preparation of spheroidal masses from a fine moist concentrate, followed by high-tempera-ture firing to produce a final product. The preparation of moist spherorids is generally designated as balling. This produces the so-called green pellets or balls. After, these have been fired they are called pellets. Balling is accomplished by rolling moist concentrates in a revolving drum until small spheroids form by a snow-balling action. These balls are then heated in a shaft furnace, or a modification of this device, to a temperature high enough to cause agglomeration within the individual balls while they descend countercurrent to hot oxidizing gases. By this process the lour strength balls are converted through various chemical and physical-chemical processes into hard pellets. With correct balling and firing, the pellets are strong, resist abrasive action and handling treatments, and provide a suitable blast furnace and open hearth feed. In 1950 Tigerschiold and Ilmoni developed a working hypothesis to explain the formation and stability of green pellets.' Their work was presented on the basis of geologists' discoveries concerning the soil-water system and C. V. Firth's early postulates of green pellet formation.' Fundamental reactions oc-curing within fired pellets have been described by Cooke and Ban, who showed the microstructure changes caused by different firing temperatures." All these investigators have provided scientific clarifications of agglomeration by the pelletizing process and have opened avenues for greater development. Mineral grain growth and ceramic bond formation are the two basic phenomena imparting coherency to particles within a fired pellet of iron ore. Each of these is established by the transfer of thermal energy to the mineral particles. Grain growth mechanisms are chiefly physical reactions wherein smaller particles consolidate into larger ones, with resulting decrease in surface energy conforming with the second law of thermodynamics. Ceramic bond formation is a chemical reaction usually between basic and acid metallic oxides of the gangue and ore minerals. CaO, MgO, A1203, and FeO of Fe3O4, react in varying proportions with SiO, or Fe2O3, to form a great series of compounds or amorphous solid solutions. These product bond iron mineral particles together by a bridging action or by direct reaction with the surfaces of the particles. The result of the grain growth-ceramic bond formations is a consolidated, coherent compact of gangue and iron minerals formerly held together by much weaker bonds of interstitial water and forces common to dry, unconsolidated particles.4 With respect to iron ore agglomeration, these high temperature bonding reactions have been described by Schwartz, who referred to the bonds in sinters," and by Cooke and Ban, who referred to the bonds in fired pellets." The extent of the bonding phenomena and the consequent strength of fired pellets is governed by

Jan 1, 1954

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry's law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2'= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,' using Laitinen and Liu's' value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,' and the equations of Wagner and Werner,' the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O' and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies' have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969