Search Documents

By George Ashley

IT has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. TABLE 1.-Pittsburgh Coal Bed to Dec. 31, 1934 Estimated Recov- State Thousands of ( Value erable Reserves Tons Mined (1935), Thousands of Tons Pennsylvania 3,144,000 $4,922,000 7,500,000 Ohio 493,391 843,699 3,000,000 West Virginia 650,000 1,027,000 5,500,000 Maryland 183,224 254,681 20,000 Totals 4,470,615 $7,047,380 16,020,000 PRODUCTION AND VALUE In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately.

Jan 1, 1936

By G. Derge, Ling Yang, G. M. Pound

The specific conductance and its temperature dependence were measured over the entire composition range of the molten Cu2S-CuCI system. At a typical temperature of 1200°C, 10 rnol pet of the ionically conducting CuCl reduced the specific conductance from about 77 ohm-lcm-l for pure Cu2S to about 32 ohm -1cm -1, and 50 mol pet CuCl reduced the conductance to that for pure CuCI—about 5 ohm 1cm1. The nature of electrical conduction in molten Cu2S, FeS, CuCI, and mixtures was studied by measuring the current efficiency of electrolysis at about 1100°C. The Cu2S, FeS, and mattes were found to conduct exclusively by electrons, but addition of 1 5 wt pet CUS to Cu2S produces a small amount of electrolysis. Addition of CuCl to Cu2S suppresses electronic conduction, and ionic conduction reaches almost 100 pet at a CuCl concentration of about 50 mol pet. These facts are interpreted in terms of electron energy level diagrams by analogy to the situation in solids. RESULTS of electrical conductivity studies on molten Cu-FeS mattes as a function of composition and temperature have been reported.' The specific conductances ranged from about 100 ohm-' cm-' for pure Cu2S to 1500 ohm-' cm-1 for pure FeS. This is in sharp contrast with the low specific conductance of molten ionic salts for which the transfer of electricity is by migration of ions in the field. In general, these ionically conducting molten salts, such as NaC1, KC1, CuC1, etc., have a specific conductance of the order of magnitude of 5 ohm-' cm-'. It was concluded on the basis of this evidence that molten FeS and Cu,S exhibit electronic conduction. Pure molten FeS has a small negative temperature coefficient of specific conductance, resembling metallic conduction, while pure molten Cu2S has a small positive temperature coefficient, resembling semi-conduction. The molten Cu2S-FeS mattes follow a roughly additive rule of mixtures, both with respect to specific conductance and temperature coefficient. Savelsberg2 has studied the electrolysis of molten Cu2S and Cu2S + FeS. He concluded that while molten Cu2S is an electronic conductor, there is some ionic conduction in molten Cu2S + FeS3 owing to the formation of the molecular compound 2Cu2S.FeS and its dissociation into Cu1 and FeS2-1 ions. The present work does not verify his results. Chipman, Inouye, and Tomlinson" have studied the specific conductance of molten FeO and report a high specific conductance, about 200 ohm-1 cm-1 of the same order of magnitude as that found for molten mattes, and a positive temperature coefficient. They interpret these results in terms of p-type semiconduction in the ionic liquid by analogy to the situation in solid FeO.1 imnad and Derne' detected appreciable ionization in molten FeO by means of electrolytic cell efficiency measurements. In order to verify the conclusion that electrical conduction in molten Cu2S and mattes is electronic, and to gain further insight into the structure of molten sulfides, the following investigations were carried out in the present work: 1) The specific conductance, s of the molten system Cu2S-CuC1 was measured as a function of temperature over the entire composition range. As discussed later, molten CuCl is an ionic substance. It was thought that if molten Cu2S were simply ionic in nature, addition of small amounts of CuCl might not have a catastrophic effect in lowering the high conductance of the Cu2S. On the other hand, if much electronic conduction occurs, addition of the ionic CuCl should have a large effect in destroying the electronic conduction. 2) The electrolytic cell efficiency of the following molten systems was measured at about 1100°C in specially designed cells: Cu3; Cu2S + FeS, 50:50 by wt; FeS; Cu2S + CuS, 15 wt pet; Cu2S + CuC1, 5.9 to 46.4 mol pet; and CuC1. This gives a direct measure of the fraction of current carried by ions in these melts. Further, the cell efficiency, extrapolated to zero ionic current, is given by cell efficiency = (s leasile + s elexstronic). [1] s lucile for molten CulS would be expected to be no greater than that for molten CuC1, whose s lonle is about 5 ohm-' cm-1, as will be seen in the following. u,.,,.,.,.......for molten Cu,S is of the order of 100 ohm-' cm-'.' Thus, a large increase in cell efficiency from 0 to values of 10 to 100 pet upon addition of CuCl to Cu2S would indicate destruction of the electronic conductance. Conductance Measurements Experimental Procedure—The apparatus and experimental method were the same as those described in detail in connection with the study of electrical conduction in molten Cu,S-FeS mattes.' A four terminal conductivity cell and an ac poten-

Jan 1, 1957

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

THERE are three chief production zones of tungsten ore in China. In the Province of Kiangsi mines are located at Kanchow, East River, and West River. Their combined production is understood to amount to 300 to 350 tons of ore per month, and their original exportation is made through the port of Kiukiang, largely to Shanghai. The second zone is in Kwangtung Province, the mines there being at Tayulin. Produc-tion reaches about 200 tons per month and cargo is gen-erally exported through the port of Hong Kong. In the Province of Hunan approximately 25 tons of ore are produced monthly in the mines at Ton-on. Tungsten ore from Kiangsi and Kwangtung Prov-inces is generally about 70 per cent WO, (tungstic acid), while that from Hunan is of lower quality, run-ning about 65 per cent WO3. Kiangsi ore is received from the mines in 100-1b. and Hunan in 224-lb. gunny sacks. No repacking is done except as it is made neces-sary by the condition of the sacks. Kiangsi Province contains the Chinese districts pro-ducing the largest amount of salable wolframite or tungsten. Many districts west and south of Kiangsi have been found to have wolframite deposits.-Com-merce Reports.

Jan 1, 1928

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose molding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat-, abrasion-, corrosion-and oxidation-resistant and high-strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, chemical process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present conditions, the US and North America, with the possible exception of Cuba, have no commercial ore reserves. There are chromite deposits, as will be described, but they would be used only under highly abnormal conditions if all outside sources were cut off for an extended period. All chromite used in the US is imported from the eastern hemisphere in which are contained the principal world reserves. The main suppliers in 1980 were the Republic of South Africa (43%), the USSR (21% ), the Philippines (12%), Albania (11 %), Turkey (8%), and others (5%). The strategic nature of chromite is obvious. End Uses-Grades and Specifications As noted before, the three principal uses for chromite are metallurgical, refractories, and chemical with a fourth minor use as foundry molding sand. For metallurgical applications chrome ore is first reduced in electric carbon arc furnaces to various types of ferrochromium alloys. There are high, medium, and low carbon ferrochromiums with carbon ranging from 0.01 up to 10%. Chromium itself ranges from 50 to 73 %. Ferrosilicon chromium and ferrochromium-silicon grades have chromium from 33 to 67% and silicon from 3 to about 48%. Since iron is reduced with chromium, the Cr:Fe ratio of the ore will determine the ultimate grade of the ferrochromium whereas carbon and silicon can be controlled during processing. MgO, A12O3, CaO, and excess SiO2, are removed in slag. A small amount of pure chromium metal is prepared by alumino-thermic and electrolytic processes from essentially iron-free chrome components that have been made via the chemical route. The higher grades of ferrochromium with chromium in the 66 to 73% range can only be made from ores with not only high chromium content, but low iron, i.e., high Cr:Fe ratio. These ores, conventionally termed metallurgical grade, have Cr2O3 contents of 45 to 56% with Cr: Fe ratios of 2.5 to 4.3. A standard composition is generally 48% Cr2O3 and 3:1 Cr:Fe ratio. Very high grade ores are often blended with lower grades even with the high iron chemical grade. For some ferrochromiums, additions of high alumina refractory grade are used as slag conditioners to facilitate smelting while still contributing chromium values. A lower grade ferrochromium, the high carbon charge chrome, has become the predominant grade in use today for making chromium-bearing steel alloys. This

Jan 1, 1983

By Jules E. Jenkins

IN the past quarter century the seismograph has played an increasingly important role in evaluating vibratory effects transmitted to adjacent communities by industrial blasting operations. In this period research has advanced through two major phases—from falling pin seismometers to three-component recording seismographs. The initial phase of this research is now regarded as the era of recording, during which the seismograph merely recorded occasional events. It has emerged from this stage into the era of control and analysis and in this later period has been recognized as a full-fledged industrial tool. Although the falling pin machines of earlier years indicated probable amplitudes of industrial blasting vibrations, they gave no reliable measure of such displacements, nor did they provide essential information concerning direction or frequency of motion. The first contribution of the three-component recording seismograph was the weight-for-distance formula developed by the U. S. Bureau of Mines. This empirical formula enabled users of commercial explosives to determine beforehand the probable vibratory effects of a blast when the weight of the explosives charge and the distance from the shot point were known. This formula has withstood the test of time and is still applicable for blasts detonated by instantaneous methods. The second major contribution of the three-component recording seismograph followed the introduction in 1945 of short period or millisecond delay detonation. This might be described as a two-stage contribution, the first of which revealed a 50 pct reduction in the vibration magnitude when millisecond detonation was used rather than instantaneous discharge. This second part of this double contribution led to the discovery of the vibration dip phenomena, see Fig. 1. In Fig. 1 the horizontal coordinates indicate the displacements amplitude in inches, and the vertical coordinates, the explosive weight in pounds. The top curve is that of the U. S. Bureau of Mines for instantaneous detonation. Its curvature conforms to the two-thirds power of the explosive weight as provided in the weight-for-distance formula; hence the vibratory effects increase in proportion to an increase in the explosive charge. If the other curves shown below are temporarily disregarded, it may be considered that the entire area below this top curve represents both useful and waste energy. As mentioned previously, when millisecond delay detonation was first investigated it was found that in general the U. S. Bureau of Mines curve could be decreased by about 50 pct, or to the position of the middle curve. At the outset it was assumed that this curve would likewise increase in some proportion to the explosive charge, as did the top curve, that is, the curve would indicate a continuous upswing. As seismographic data accumulated this assumption was found to be erroneous in part. It was discovered that

Jan 1, 1957

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By Raymond C. Johnson

GASIFICATION is important to the anthracite industry, as it is to the entire solid-fuel industry and to the nation. However, to the anthracite industry it may have particular significance in that it would increase the market value of many millions of tons of a by-product fuel, which the industry now has in storage and is currently producing, in addition to increasing the potential market for all its products. The by-product fuel is of usable quality but the ash content is higher than it can be in other products and therefore it must be converted or used at the point of production. Gasification is one method by which the product may be given increased value. The inherent characteristics of anthracite make it well suited for producing a fuel or synthesis gas. It is the most concentrated form of natural commercial carbon, noncaking and noncoking; it does not produce smoke, tar, or soot and has a low sulphur content; and the volatile matter, which ranges between 2 and 8 pct, is 80 to 85 pct hydrogen with small amounts of methane, carbon dioxide, carbon monoxide, and nitrogen. The ash fuses at high temperatures, which allows it to be burned at high rates without slagging. However, with the addition of small amounts of dolomite, the ash will form a slag, or glass, which is very fluid. Anthracite has long been used in the manufacture of city gas and it is extensively used in various parts of the country to make water gas to be converted to hydrogen. Buckwheat and rice anthracite are used in Galusha producers to make producer gas. Excellent synthesis gas has been made in a Galusha producer with rice and barley anthracite with oxygen in tests at the Consolidated Mining and Smelting Co., Trail, British Columbia. In these tests, anthracite was shown to have advantages over competitive fuels, in that the gas had a higher hydrogen content and could be cleaned with less difficulty. The anthracite seams are steeply pitching and in mining the parting strata and some of the roof and bottom materials are taken with the coal. In preparation, these materials are separated by gravity from the commercial product and stored in refuse banks. This refuse contains a mixture of rock, slate, or shale, and high-ash anthracite with bone coal, which is low-ash coal that is interspersed with thin bands of shale. The bone coal contains between 25 and 50 pct ash with an average ash content of approximately 30 pct, with a

Jan 1, 1953

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst&apos; and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By AIME AIME

IT is unlikely that any oil field has ever threatened the future course of the oil industry as does Kettleman today. It seems that nature has striven to outdo herself in combining in this field every possible factor conducive to a tremendous production of the petroleum product in greatest demand-gasoline. This field already has 13,700 acres of proved land and an oil zone of known thickness of 1400 ft. It has wells yielding several thousand barrels of oil of virtually motor fuel grade, together with millions of cubic feet of gas at almost unheard of pressures. The field would have been the. answer to an oil man&apos;s prayer in times of under-supply, but now it is the oil man&apos;s nightmare, for drilled in -the manner of most other fields and without regard to available markets for oil and gas, the greatest physical and economic losses in the his¬tory of the oil industry will result.

Jan 1, 1930

By U. C. Tainton

THE world-wide continuation of low prices for zinc in 1934 has militated against any striking changes in the position of the metal. The price of zinc in London at the end of the year, about £11 5/8 per long ton, or 2.5c per pound at the existing rate of exchange, is more than 25 per cent below the average price for last year. In these circumstances probably the most significant event of the year was the putting into operation of the new electrolytic plant of the Giesches company at Magdeburg, Germany. This plant is designed to have an initial capacity of 20,000 long tons per year, and it is planned to increase this to 40,000 tons annually. This development is significant not only as indicating a continued swing of zinc metallurgy towards electrolytic methods, but also because it will make Germany virtually independent of foreign sources of zinc. This will mean that the zinc tonnage normally exported to Germany from Belgium and Poland will. become available for other markets, and it is feared may lead to lower prices unless the production of Bel-

Jan 1, 1935

By W. M. Weigel

THE rapid advance, during recent years, in the manufacture of articles that have been in common use for generations and the development of new materials entering into appliances and devices unheard of fifty years ago, have created a demand for some of the more common non-metallic minerals. To supply this demand there has quietly developed a branch of the mining industry of which little is known by most mining engineers the mineral-filler industry. In this paper, and generally in the trade, the term mineral filler is applied to a mineral used, in its natural state after mechanical preparation only (such as. grinding, milling and washing), without undergoing any chemical change and without exerting any chemical action on the substance with which it is incorporated. The consumption of mineral fillers is confined chiefly to large manufacturing centers in the eastern and northern states. Where available, materials originating near the place of consumption are used, as most fillers bring a comparatively low price and, frequently, the freight may equal the cost of the finished filler at the mine. The southern states have abundant deposits of non-metallic minerals suitable for fillers, which supply the manufacturing industries in adjacent states. Many of these deposits are equal to, or superior, in quality to those mined in the north, but they can not compete with them because of the freight rates. The mineral-filler industry has felt the present depression, but it has suffered less than most mining industries for as a rule the mills are simple, the overhead expenses are low, and the labor is entirely local and can revert to farm work when the plant closes down. Many other deposits in the southern district will undoubtedly be developed when business. revives and freight rates are adjusted.

Jan 2, 1922

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress&apos; four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver&apos;s new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers&apos; courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952

By Alfred Siegel

Mineral pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, but rather such compounds as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-limonite (2Fe2O3.H2O to Fe2O3.4H20), hematite (Fe2O3), or magnetite (Fe2O3.FeO). Man&apos;s first permanent coloring materials were earth pigments-the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands forth with $16,000,000 per year; it is surpassed by titanium, lead and zinc pigments. Of this sum,21 natural pigments supplied 31 pct of the tonnage and 16 pct of the value of the total finished pigment in 1957, the remainder representing the tonnage and value of sales of the synthetic iron oxide colors. The average value of finished natural pigments in 1958 was $80.62 per ton. The average value of manufactured pigments in the same year was $202 per ton. Of the 60,000 tons of manufactured colored pigments sold in 1958, the reds comprised 76 pct of the market and the yellows 20 pct. The reds furnished 68 pct of the value and the yellows 24 pct. Of the finished iron oxide pigments (natural and manufactured) sold in 1958, the reds dominated the market with 66 pct of the quantity and 63 pct of the value; yellows supplied 17 pct of the quantity and 20 pct of the value, and browns furnished 11 pct of the quantity and 10 pct of the value. The average value of the reds was approximately $152, and the average value of the yellows $190 per ton. The highest valued pigment in 1958, with almost 12 pct of the total tonnage and 21 pct of the value of the iron oxide pigment market, was manufactured red from calcined copperas valued at $286 per ton.

Jan 1, 1960

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950