Search Documents

By John F. Elliott, John R. Rawling

The rate of reduction of silica to silicon by carbon at 1550° to 1700°C in iron blast-furnace type slag-metal systems has been investigated. In the tower portion of the temperature range oxygen transport in the metal boundary layer at the slag-tal interface is probably rate limiting. A second step, which apparently involves a chemical process in the slag at the slag-metal interface, appears to be rate limiting when the oxygen-transport limitation is avoided. Above 1650°C rate control of the reduction by carbon probably is mixed between the two steps. INVESTIGATIONS1.2 into the equilibrium distribution of silicon between graphite-saturated slags and metals typical of iron blast-furnace practice show that, under the experimental conditions specified, the reduction of silica to silicon is relatively slow compared with the rates of other slag-metal reactions under similar conditions. For this reason, the reduction of silica in blast-furnace slag-metal systems was considered to be an interesting subject for further study. Investigations of the kinetics of the reaction3-5 suggest that several possible steps may be rate controlling, and that the rate-controlling step depends not only on the physical state of the systems but also on the configuration of the apparatus. The main objects of the investigation reported here were to sug- gest plausible reaction paths for the reduction of silica under the experimental conditions chosen and to determine the step or steps which control the rate of reduction of silica. EXPERIMENTAL Two types of experiments involving the reduction of silica from the slag were carried out. In the first, the only reducing agent present was carbon (graphite), for which the over-all reaction is (SiO2) +2C(gr) —Si + 2Co(g) [l] The second type was a graphite-saturated ferro-silicon-iron concentration cell. In it silica in the slag could be reduced either by carbon according to Eq. [I], or by a reaction of electrochemical nature in which silicon was oxidized at the ferrosilicon-slag interface and silica was reduced at the slag-iron interface without the formation of CO. The two types of experiment are described below. Reduction of Silica with Carbon as the Only Available Reducing Agent. The reduction of silica was accomplished by allowing a liquid lime-alumina-silica slag and graphite-saturated iron to react in an induction-heated graphite crucible. The crucible was 2.25 in. diameter and 5 in. deep; it was fitted with a graphite stirrer which penetrated through the slag and into the metal, Fig. 1. The slag and metal charges weighed 350 g each. Pure carbon monoxide at a pressure of 1 atm was maintained above the melt by passing the purified gas through the crucible at a rate of 0.5 liter per min. The gas did not stir either the slag or metal. Temperature measurements were made by sighting an optical pyrometer down the hollow stirrer rod into a 1/4-in. hole drilled in the stirrer blade. The crucible temperature was maintained within *15"C of the required value by manual control of the power supply to the

Jan 1, 1965

By G. N. Maniar

G. W. Healy (union Carbide Metals Co.)-The author's paper is a useful contribution to the store of maps of chemical activities of oxides in multi-component slag systems. It is also a good example of the utility of the Gibbs-Schuhmann technique for calculating activities in a system where that of one of the components has been measured. This paper Koh and Caugherty. This plot is reproduced by alor in X-ray Metallography. Because of this nonlinearity, preparation cf suitable standards and/or correction for absorption and enhancement are essential in microanalysis. However, our objection is not the conclusion that Dr. Aaronson has arrived at nor the technique he has used; but only to the foot-note credited to V. Macres. The level of chromium that he was concerned with (less than 3 pet) is so low that the deviation of uncorrected Cr-curve will be negligible. Besides Dr. Aaronson has used chromium intensity from martensite and set it equal the bulk chromium content of the alloy. Using this chromium-intensity as a reference, he has calculated the amount of chromium in the ferrite. This amounts to the same as using an internal standard. Since the chromium content in austenite and ferrite are almost the same, enhancement due to iron in both will be the same and therefore does not need to be corrected. together with the author's recently published one1 on the CaO-FeO-Fezo3 system will be most helpful to others learning to apply Schuhmann's method, which merits a far wider application than it has received to date and should greatly aid our understanding of equilibria between metal and oxide phases. As shown by okcen" its use may even be extended to sections of systems with any number of oxides. I have some questions as to the selection of equilibrium constants made by Dr. Turkdogan. He has chosen one for the formation of Fe2O3 from FeO and oxygen which gives Fea3 activities 50 pct higher

Jan 1, 1963

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for', all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By E. DeGolyer

I. INTRODUCTION VOLCANIC origin. was among the first of the theories advanced to account for the occurrence of the salt domes of the Gulf coastal plain, northern Louisiana., and eastern Texas, and it is still being re-stated in various forms by the most recent contributors to our knowledge of the geology of such deposits. Argument has been largely by analogy and attention has repeatedly been called to the Mexican oil fields, particularly those of the Tampico-Tuxpam region, because of the occurrence of oil in close proximity to volcanic plugs in those fields, an occurrence supposed to have some resemblance to the common occurrence of oil in the salt domes of the United States. The author, having spent several months of the past year in a general study of salt domes and in a detailed study of certain domes in the United States, and having been acquainted for some time with the exploration of similar domes in the Isthmus of Tehuantepec region, Mexico, and with the general geology of the Tampico-Tuxpam region, Mexico, has reviewed the various theories of volcanic origin for salt domes which have been advanced to the present time. The purpose of this paper is to present such review and to discuss the supposed Mexican analogy.

Jan 5, 1918

By Wei-Kao Lu, G. Bitsianes

An improved general rate equation for a one-ditnensional gas-solid system has been derived. Fov the veversihle interfacial chemical reaction, there are concentrations of gaseous reactant and product at the reacting zone to be considered. They have been calculated with the velations fuvnished by the constraints on the system, namely, quasi-steady state and equimolal counterdiffusion of the gases. The results of the diffusiori study of Evans, Watson, and ,Mason based on the "dusty gas" model have been applied here. The interfacial chemical reaction is taken as first-order with respect to the concentration of the gases involved. The equation has proper dependence on gas composition and on solid structure through the relative values of Knudsen and normal diffusivities. The existence of the total pressure gradient inside the specimen has been predicted and confirmed experimentally. In a previous communication' we introduced a general rate equation for gas-solid reactions by considering the contributions of chemical reaction at inter- phase boundaries and diffusion through the solid product layer simultaneously. These equations, for one-dimensional and spherical specimens, take care of the whole range continuously from purely diffusion control to purely chemical reaction control. In this paper we study only the one-dimensional system. The corresponding rate equation is reproduced here: Of the two terms on the right-hand side of Eq. [I], the first represents the contribution of interfacial chemical reaction and the second that of gaseous diffusion. The shortcomings of Eq. [I] are that in its derivation the interfacial chemical reaction was assumed to be irreversible and the diffusion rate of gaseous product was not considered. Any pressure effects building up within the porous media were also neglected. Evidently. these simplifying assumptions will limit the general applicability of these equations. The rate of reduction of iron oxide by hydrogen, for instance, is very sensitive to the concentration of water vapor in the main gas stream, as has been reported by cewan' and by Quets et a1.3 Furthermore, the gaseous phase at the reacting interface will contain an appreciable amount of the gaseous product of reaction. If this were not true, a sufficiently high concentration gradient for the outward diffusion of the gaseous product could not be maintained. With these shortcomings in mind, Eq. [1I cannot be rigorously ap-

Jan 1, 1967

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region [ ] This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 in. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine--almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies,

Jan 1, 1950

By Smith, George Otis

THE matter that I have on my mind this evening is engineering's need of an open forum. Our fathers of three centuries ago were pro-testanta for freedom of speech and thought in matters religious; later, our fathers were revolutionists for freedom of speech in matters political; until today freedom of speech has become so universal throughout the land that even in the sanctuary of our homes, at times, we have to turn off the loud-speaker. Talk is not always a condition of progress, but light is everywhere necessary to growth, whether the growing thing is a blade of grass, a baby chick, or a young idea, and we must regret anything that tends to shut out the light from the operations of business and industry. Of course, I realize there is little that is novel in what I am saying. Indeed, I have found that Dr. James Douglas-a name we love to honor in our Institute-as long ago as 1907, gave an address at the Toronto meeting that any of us would be proud to be author of twenty-one years after. Dr. Douglas at that time spoke on secrecy in the arts and the text then taken by this leader in metallurgical technique and in the constructive management of big business was "the dangerous temptation to adopt secretive methods by very large corporations." In both thought and language Dr. Douglas was direct and vigorous and he needs no internreter. He advocated the wide open door for ideas on two counts: advancement of technical knowledge and education of public opinion. A few sentences will serve not only to prove the vision of James Douglas, but also, I hope, tempt you to hunt up his address in the Institute's TRANSACTIONS, and thus get his whole thought first hand.

Jan 1, 1928

By Smith, George Otis

ENGINEERING is in essence quantitative, and the engineer must deal with exact figures when he plans and, constructs. Engineering truths are not best expressed by adjectives, yet my wish, today, is not to attempt a quantitative measure of the dominant position of the mineral industry of the United States in the existing scheme of material things, but rather to seek a clualitative appraisal of what mining and metallurgical engineers are doing to promote and make secure our , national progress. Statistics help when we wish to gage material prosperity, but they fail when we desire to determine what share the engineers have in adding to the happiness and welfare of our people

Jan 1, 1928

By S. A. Montague

Mica can claim a considerably greater importance than would be assumed from its comparatively small dollar volume, which came to about $37,000,000 for the United States industry as a whole in 1957. Mica is one of the strategic minerals. We must depend on imports from distant sources for virtually all of our requirements of high grade block and all of our mica splittings. Mica is essential and indispensable for vacuum tubes and high-performance condensers, two electronic components which are vital military necessities besides being nearly indispensable to civilization today. Composition and Properties Mica is the general name for a group of some nine different minerals, two of which, muscovite and phlogopite, are the minerals used by the mica industry as its raw material. Several of the other varieties are commercially useful-vermiculite, * used for heat insulation in expanded form, and lepidolite, used as an ore of lithium while the others-biotite, roscoelite lepidomelane, paragonite and zinnwaldite have little or no commercial importance. Biotite frequently occurs as an undesirable impurity in muscovite. Table 1 lists various properties and other data concerning muscovite and phlogopite. Chemically, mica is a complex silicate of sodium, potassium and aluminum. Most varieties of muscovite are higher in sodium, and of phlogopite in magnesium. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite occurs in a range of color from the so-called India "ruby" which is more closely a pinkish brown, to light and dark green, with numerous other intermediate shades. Ruby color is usually preferred by industry, especially in the better qualities. When split very thin the color in most [ ] micas disappears. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite

Jan 1, 1960

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey' have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel'perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,' and Fletcher and Wilson' have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By William L. Saunders

Many members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-coxpressors and machinery driven by compressed air, has no desire to injure its own business by claiming for this new machine that it should immediately supersede all existing applications of pneumatic transmission of power for drilling. On the

Jan 1, 1908

By N. Jaffee, J. E. Dorn

An activation energy of 27,400 5 1000 cal per mole was obtained for the creep of poly crystaLline aluminum over the temperature range of 273° to 350°K, at strains varying from 0.003 to 0.230. Stresses varied fronz 2250 to 6000 psi, strain rates from 0.1145 x 10-5 to 29.5 x 10~s min.-1. A strain temperature-compensated time correlatzon was oblained indicating that the structure was depedent solely upon the strain at a given stress; X-ray diffraction analyses and tensile tests on precrept specimens verified this. PREVIOUS investigations1 have revealed that the apparent activation energies for creep of high-purity polycrystalline aluminum are insensitive to the applied stress, strain, and strain rate. On the other hand, the apparent activation energy is dependent on the temperature1,2 as shown by the data reproduced in Fig. 1. Each plateau of this curve is associated with a unique rate-controlling dislocation mechanism for thermally activated creep. It is now very well-established that over the high-temperature range, where the activation energy is about 35,500 cal per mole, the creep rate is controlled by the dislocation climb mechanism. 3 Over the intermediate range of temperatures, from about 260° to 370°K, another unique activation energy, namely 28,000 cal per mole, is obtained. Current evidence strongly supports the contention that cross slip is the rate controlling mechanism for creep in this case: 1) Crystal recovery can occur by a number of mechanisms prominent among which are climb and cross slip. Astrom,4 using the Borelius micro-calorimeter, reported rapid crystal recovery of cold-worked polycrystalline A1 at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at 455° to 478°K giving an activation energy of 3 6,000 cal per mole. Whereas the latter recovery process was clearly associated with the dislocation climb mechanism, the former, 28,000 cal per mole process could have arisen as a result of the cross-slip mechanism. 2) Single crystals of high-purity A1 favorably oriented for octahedral glide exhibit an activation energy for creep of about 3400 cal per mole over the range from 0° to 400°K and that of about 28,O:O cal per mole over the range from 600° to 775°K . Whereas the lower activation energy process is accompanied by the development of sharp slip-band traces, the 28,000 cal per mole process was uniquely characterized by extensive cross slip. 3) Theoretical calculations by Seeger and schoeck6 suggest an apparent activation energy for cross slip in A1 of about 24,000 cal per mole and another theoretical estimate by Friedel 7 gives the observed 28,000 cal per mole as the theoretical activation energy. It is therefore consistent with this evidence to, at least tentatively, ascribe the 28,000 cal per mole creep process in A1 to the operation of cross slip as the rate controlling mechanism. Although creep has been rather well-explored in the dislocation climb range, very little, excepting perhaps the activation energy, is known about creep in the cross slip range. This investigation was undertaken, therefore, to reconfirm the activation energy for creep in polycrystalline A1 in the intermediate temperature range and to study the strain-time relationship for creep at a constant stress in the cross slip region. EXPERIMENTAL PROCEDURE AND TECHNIQUE The three types of high-purity A1 alloy specimens described in Table I were used in this investigation. Specimens were milled from 0.100 in. thick cold-rolled sheets with their tensile axes in the rolling direction following which they were given a recrys-tallization and grain growth heat treatment at temperatures well above those which were subsequently employed in the creep tests.

Jan 1, 1962

By John. C. Reed

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62° W. The average dip is about 67° SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30° W. and average dips about 75° SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30° for the south-west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By R. G. Schaal

The Magma Mine at Superior, Arizona had an unimpressive beginning as a. worked out silver mine that was purchased in 1910 for $130,000 and then incorporated into the Magma Copper Company which has been continuously mining the deposit since 1915. Copper is the principal metal produced. However, zinc, gold, silver and iron have also contributed to the total metal product. Prior to 1973, the production rate of 1500 tons per day was maintained by hoisting 4 and 5 ton pay-loads at speeds up to 1100 FPM through four small hoisting shafts. The hoists used included 8' and 7' diameter double drum, double clutched doc. and a.c. motor driven geared units built as early as 1917. One old timer that did yoeman's service for many years was an 8' Bollen Pulley with a.c. geared drive that utilized an endless rope system with mechanical grip and release mechanism built into the pulley's throat. Primary power for all of these old production hoists was 25 Hertz. Exploration that was completed in 1967 developed a reserve of 10 Million tons of 5 per cent copper which was sufficient to justify new capital expenditures for enlargement of productive facilities to 3300 tons per day. To reach the new reserves a 22' I.D. concrete lined vertical shaft was sunk to an initial depth of 48431. A 12 ½ diameter adit was bored from the mill side of the mountain to intercept the shaft at a point about 1100' below the collar. This 9200' long adit provides the right-of-way for the mine to mill railway and egress for heavy supplies from rail head as well as a conduit for potable water, electric power, compressed air and mine drainage. Mine operating levels begin 3582' below collar and thereafter have been cut at 100' vertical intervals. Skip loading stations have been installed 4282' and 46821 below collar with an in-shaft skip dump station located 800' below collar. This provides for 4500 tons of storage above the mine to mill train loading station located 1100' below collar. Ore and waste are moved horizontally from stope chutes and drift headings by rail haulage to transfer raises which channel all material to the two mentioned skip loading stations. The 22' diameter shaft crossection is arranged with the two skip compartments on the south side separated from the manway and utility compartments by the cage compartment. The cage counterweight operates in a portion of the southwest quadrant of the shaft. The hoisting plant consists of two conventional Nordberg double drum, single clutch, geared, d.c. motor driven units that are identical except for the drives and automatic controls. The drums are 15' diameter x 105" face with LeBus grooving for 2-1/8" diameter wire rope wound in three layers. Mechanical design emp1o::ed is the same as has been used for the past twenty- five years. One drum is attached to the main shaft by 2 large bolted integral shaft flenge. The loose drum is engaged by a 4-arm positive tooth clutch meshing with radially cut teeth of the clutch ring which is bolted to the drum. The drums are one-piece steel plate weldments having a finished weight of 60 tons each and are mounted upon a 36" diameter shaft that also weighs 60 tons. With the addition of brake rings, clutch, bull gear and rope, the total dead weight adds up to nearly 250 tons that is supported by just three double row spherical roller pillow block bearings. There is no bearing between the drums. All pinion shafts as veil as all head sheave journals are supported in the same type of antifriction bearings.

Jan 1, 1975

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By B. C. Raynes

IN the early part of 1952, under the auspices of the U. S. Atomic Energy Commission, Horizons Inc. undertook an investigation dealing with the preparation of high purity thorium metal in order to develop an economically competitive production process for this metal based on a recovery of the metal by a fused salt electrolysis, since a survey of the literature of thorium chemistry indicated that electrolytic methods had not received much attention, despite the consideration that electrochemical production methods often offer attractive commercial potentialities. Thorium metal has been prepared by methods which fall into four general categories: 1) reduction of halides or double halides; 2) reduction of the oxide; 3) thermal decomposition of halides; and 4) electrolytic methods. Some of the important results obtained by various investigators since about 1900 in recorded attempts to prepare pure thorium metal are summarized in Table I. A bibliography of pertinent literature is included in this paper. Thorium is strongly electropositive and possesses a great affinity for oxygen and nitrogen. As a result the prospects for the production of high purity thorium from aqueous media or oxygen bearing compounds are remote. The most promising and profitable area of investigation for production of thorium metal lies in fused salt electrolysis. Thorium has been produced previously by this technique from halide salts in fused alkali chloride eutectic mixtures. Until recently, however, the lack of known large uses for thorium has inhibited the investigation of these methods. The basic problem in an investigation into fused salt production methods for thorium is to develop a suitable fused salt system for the economic preparation of thorium. The first portion of the work in these laboratories was a small scale investigation of the electrolysis of potassium thorium fluoride, KThF5, under a variety of conditions. High purity thorium was prepared in this manner, but the process did not appear to offer the simplest and most attractive continuous commercial operation. The work reported here relates to an all-chloride system employing thorium chloride as the cell feed. ThCL4 was produced as an anhydrous material stabilized in molten sodium chloride. This product, further diluted in NaCl, was subjected to electrolysis. The electrolytic process has been studied in cells capable of holding up to 50 lb total salt charge. Ductile, pure thorium metal has been reproducibly obtained in this operation. Considerable experimentation was carried out in the preparation of ThCL as a cell feed free from moisture, oxides, and other impurities. Thorium was cathodically deposited as a coarsely crystalline powder interspersed with residual bath salts. Aqueous procedures for separating and recovering the metal were developed. The thorium metal powder obtained has been evaluated with respect to its hardness, chemical purity, and certain other physical properties. Preparation of ThC1,—Thorium chloride, and the chlorides of some other metals (aluminum, beryllium, tantalum, zirconium, etc.) cannot be obtained from aqueous solution by direct heating and evaporation. Evaporation and heating of a solution of thorium chloride yields a hydrated salt or partially hydrated salt, and finally Tho,. Anhydrous thorium chloride is obtained by forming a hydrated ammonium chloride complex salt in acidified water solution, dehydrating this compound, and finally decomposing the double salt and subliming the ammonium chloride component. Various methods for the preparation of anhydrous thorium chloride, in accordance with this concept, were investigated as indicated in Table I1 from hydrated thorium chloride (ThCl, . 3H2O), and from thorium oxycarbonate (ThOCO,). In the method found most satisfactory for this work, thorium oxycarbonate was dissolved in an excess of concentrated HC1 to give a clear yellow solution. At least 2 mol NH,Cl were added to the solution per mol of contained thorium. Ammonium thorium chloride hydrate was crystallized from solution by cooling and saturation with HC1. The resultant complex, (NH,Cl),ThCl;xH,O, was dehydrated by evaporation at 130° to 150°C and thoroughly dried at about 250°C. The dried ammanium thorium chloride was then mixed with sodium chloride in proportions to form NaThCL or to produce a ThCL4-NaCl mixture with a given thorium content. The ammonium chloride was sublimed off at temperatures above 500°C in an inert atmosphere furnace to give an anhydrous chloride source electrolyte, essentially free of Tho, and of NKC1.

Jan 1, 1958

By Arthur Hockman, Howard W. Jaffe, Howard F. Carl

THE problem of establishing practical techniques for evaluating natural corundum ores arose from the desire to improve the existing purchase specifications for crystal corundum procured by the Federal Government for stockpiling. Such purchase specifications had been developed for a large number of products, including minerals and ores considered to be critical and strategic because of the country's dependence on foreign sources of supply. It will be apparent to anyone considering the subject of purchase specifications that the determination of whether or not a submittal meets the specifications is a prime consideration. Consequently satisfactory specifications for minerals should not only incorporate physical, chemical, and mineralogical requirements that are practical but should also establish the means by which both buyer and seller can be assured that materials meet stated requirements. The Munition Board's Material Purchase Specification for corundum, dated February 1954, covered two grades of crystal corundum intended primarily for abrasive use. It established limits of size and of composition: Grade A, at least 95 pct +3 mesh and 92 pct alumina (Al2O3); Grade B, at least 95 pct +7 mesh and 90 pct alumina. It also specified that "of each lot of material, not less than 95 percent shall have a hardness equal to or exceeding nine (9) on Moh's Scale." These specifications were unsatisfactory for several reasons. They did not allow the purchase of lower grades of corundum being used by industry. Neither did they specify exactly what a corundum ore actually was, except that it should contain so much alumina and have a certain scratch hardness. Nothing was said about the abrasive qualities of the material that was to be purchased primarily for abrasive use. During the period 1946 to 1948 supplies of the two grades defined in the then current specifications continued to decrease. Early in 1949 industry recommended that the finer sizes of corundum known as "crystal corundum concentrates," ¼-in. to 16-mesh material, be added to the stockpile specifications and that lower grades of crystal corundum also be included. In the spring of 1949 the National Bureau of Standards and the Bureau of Mines were asked by the Munitions Board to cooperate in developing more practical specifications for grading natural corundum ores. The National Bureau of Standards indicated that it would investigate physical test methods for determining abrasive characteristics of corundum, and the Eastern Experiment Station of the Bureau of Mines at College Park, Md., stated that it would consider the mineralogical aspects of the problem. Members of these two agencies, in consultation with representatives of the Office of Materials Resources of the Munitions Board and of the Federal Supply Service of the General Services Administration, and with the cooperation of industrial suppliers and consumers of abrasive corundum, developed, in a fairly short time, more practical specifications for six grades of corundum ores. The new specifications, issued January 1951, were for corundum, natural crystals, as by this time high-purity synthetic corundum was available and widely used. Nevertheless, for certain specific applications the natural product was preferred over the synthetic material. It has been extensively used in forming snagging wheels. It breaks into more or less cubical particles, whereas artificial corundum fractures into splintery shapes. These produce irregular cuts in glass, while the more symmetrical shape produces a more uniform ground surface. For this reason natural corundum has been preferred for certain types of lens grinding. Pure corundum is clear, colorless alpha alumina (A12O3), but it is rarely found in nature in this form. The most important gem varieties include the blue and yellow sapphires and the ruby. Minute impurities of titanic oxide impart a blue color,

Jan 1, 1955

By G. R. Speich, D. J. Mack

The transformation of was studied by isothermal methods. At all temperatures, the ß transforms quickly to fine grained ß" which develops silver-rich striations. At higher temperatures the striations disappear, the final structure being Widmanstatten a in ß'. At lower temperatures, the striated ß" is consumed by pearlite nodules of a + ß' which in turn form the Widmanstatten a in ß'. The transformation is unlike any previously reported for a eutectoid. AS part of a general program of study on the eutectoid reaction, the Ag-Cd eutectoid seemed particularly attractive because the ß phase which undergoes the reaction is another of the typical "electron compounds," AgCd, having the disordered body-centered cubic structure. This work deals with the eutectoid which occurs at 50.5 wt pct Ag, and not with the eutectoid which has been reported at 42.9 pct Ag.' There has been no work reported specifically on the Ag-Cd eutectoid which was studied. The only information available on this eutectoid is that work done in the determination of the phase diagram. For the most part, the terminal portions of the diagram, Fig. 1, are well established; however, the region from 40 to 60 pct Cd is still somewhat in doubt. The X-ray evidence'..' in this region is in conflict with the results of thermal analysis. X-ray analysis3 does not show a polymorphic transformation at about 240°C as indicated by thermal analysis.1,5 Even the X-ray evidence, within itself, is confusing in this region of the diagram. One investigator2 reports the ß phase as hexagonal close-packed and has found three phases in the one-phase ß field. Other X-ray investigators"' ' report the ß phase as body-centered cubic. The authors believe that much of the confusion resulted from incomplete homogenization of the alloys. It was found that it takes almost a week to produce a completely homogeneous two-phase structure at 370°C. Another possible source of error is the volatilization of cadmium from the surface and cracks of the specimen during annealing with the possible formation of a cadmium-poor phase. The only metallographic data available on this eutectoid alloy are those of Durrant1 and Fraenkel and Wolff.5 his information is very limited. The phase diagram chosen as most nearly correct is that in the Metals Handbook," which is almost identical with the phase diagram suggested by Durrant.1 Materials and Procedure The alloy was prepared from high purity silver (999.5 plus fine) and high purity cadmium (0.02 Pb, 0.005 Cu, trace Fe). The metals were melted in carbon under a nitrogen atmosphere. Some cadmium was lost by volatilization but by remelting several times and adding cadmium a 200 g ingot of approximately eutectoid composition was obtained. Because the CdO fumes are quite toxic, the exit gas from the furnace was led through a water trap to condense the CdO. The ingot was homogenized at 650°C for 24 hr, no attempt was made to prevent decadmiumization. This resulted in a narrow decadmiumized rim on the ingot which was removed. Filings for analysis were obtained from cross sections of the ingot. Silver was determined by the Volhard thiocyanate method,? cadmium by difference. The ingot analyzed 50.8 pct Ag at the top of the ingot and 50.7 pct at the middle and at the bottom of the ingot. This alloy was only slightly hypo-eutectoid compared to the accepted value of 50.5 pct Ag and was used for the isothermal studies. It was felt that further attempts to adjust the composition might be futile because of the volatility of the cadmium. The ingot was sectioned to specimens approximately 3/4 x 3/4 x 1/8 in. These specimens were "austeni-tized" for 3 hr in air at 650°C to yield homogeneous ß and then quenched into a salt bath held at constant subeutectoid temperatures where the transformation

Jan 1, 1954

By Mason K. Banks

A process has been developed which produces spodumene concentrates assaying 6.0 pct Li2O and 0.45 pct Fe2O3, with 70 to 75 pct recovery of spodumene. Two flotation separations are required: the simultaneous removal of mica, feldspar, and quartz as a froth product using a cationic collector, and the subsequent removal of iron-bearing minerals as a froth product while spodumene is depressed as a tailing. SINCE the close of World War II there have been numerous developments resulting in the increased use of lithium by industry. Notable among these has been the development of an industrial lubricant, based on lithium stearate, which is fluid at low temperatures, stable at high temperature, and insoluble in water. A new bleaching agent, lithium hypo-chlorite, has also been developed recently.' Other well-known uses are listed below: 1—Lithium oxide in ceramics reduces firing time, lowers melting temperatures, lowers thermal expansion, raises refractive index, and improves chemical resistivity. 2—Lithium carbonate and lithium strontium nitrate are used in pyrotechnics for their brilliant red color.' 3—Lithium chlorides and fluorides are used as fluxes for welding aluminum and magnesium.' 4—The affinity of lithium for nitrogen is the basis for a process used in purifying helium." 5— Lithium chlorides and bromides are used in air conditioning for their powers to absorb organic amines, ammonia, and smoke.6-—Lithium hydride has been used as a source of hydrogen to inflate life rafts and balloons used by the Air Forces and Navy.' 7— Lithium metal and lithium hydride are useful in the atomic energy program in connection with the production of the isotopes of hydrogen." During the 1942-45 period of World War 11, Solvay Process Co. operated a flotation plant with a daily capacity of 300 tons of ore for the production of spodumene concentrate near Kings Mountain, North Carolina. The operation was shut down upon reduction of wartime demand for lithium chemicals, and until recently there has been no production from the Carolinas. In April 1950 an investigation of the problem of spodumene flotation from North Carolina ores was begun at North Carolina State College Minerals Research Laboratory at Asheville, N. C. This laboratory, operating under the combined auspices of North Carolina State College, North Carolina Department of Conservation and Development, and the Tennessee Valley Authority, undertook the spodumene project at the request of Foote Mineral Co. of Philadelphia. The work, involving a period of 15 months of intensive batch and pilot plant investigation, was completed in June 1951 and resulted in development of a process for concentration of spodumene by flotation which has been hereto unrecorded in the literature. A similar approach has been used before on iron, ilmenite, and other minerals, but the literature shows no record of its having been applied to spodumene. Parts of the process are now being used on a commercial scale at the Foote Mineral Co. plant near Kings Mountain, N. C., which has been in production since July 1951. It is the purpose of this paper to describe some of the results of the investigation. The Orebodies Spodumene-bearing pegmatites occur in a narrow belt 24.5 miles long and 1.8 miles wide extending southwestward from Lincolnton to Grover, N. C. According to statements judged to be conservative, the tin-spodumene belt of the Carolinas contains an estimated 4,300,000 tons of pegmatite ore averaging 15 pct spodumene. This amounts to "a reserve of at least 650,000 tons of spodumene (more than 20,000 tons of metallic lithium) to a depth of 100 ft."' This figure includes only bodies having an average thickness of 35 ft and length of 550 ft. There are hundreds of pegmatites in the belt, many of which are less than 10 ft wide. The largest pegmatite in the area has a maximum thickness of 395 ft and maximum length of 3250 ft.' These larger pegmatites are composed principally

Jan 1, 1954

By C. E. Birchenall, G. Derge

IN studying the kinetics of slag-metal reactions, it has become increasingly apparent that a complete knowledge of all aspects of interface phenomena will be required to clarify these processes adequately. A part of the data required for all oxidizing slags used in the refining of impure iron to steel is the rate of exchange of iron between the slag and metal phases. The simplest equilibrium of this type is that between liquid iron and iron silicate slag when both phases are equilibrated with the silica crucible containing them. In this study, the exchange of iron between the two liquid phases has been measured by using radioactive Fe as tracer. The observed high exchange rate indicates the ease with which such interfaces may be crossed in refining processes. The experiments required for this study involved relatively minor and normal modifications of well established techniques. Melting was accomplished by induction heating in heavy walled, fused silica, rotating crucibles." Rotation was used to minimize dilution of the slag by crucible erosion. The melting stock was ingot iron. Slags were prefused in iron crucibles using chemically pure grade oxide reagents. The special conditions applying to the active iron additions will be described for individual experiments. Suitable precautions were observed with regard to protection against radiation hazards.' Identification of Activity This particular study was initiated several years ago, but held in abeyance because the radioactive iron available at that time contained a foreign activity which concentrated in the slag so as to mask the iron activity and render the results unin-terpretable. With the benefit of experiences from other studies, radioiron of suitable purity can now be prepared. As received from the Isotope Div. of A.E.C., the unit appears to contain Fe + Fe50 and a high activity cobalt. The cobalt and iron are separated by repeated ether extractions, and the purified iron stored for sufficient time for the Fe'7 44 day half-life) to decay to negligible activity, leaving only Fe as the active isotope. This was confirmed by the absorption curves for slag and metal samples from heat No. 1. In Fig. 1 the experimentally measured points for the absorption curves of slag and metal are fitted by the calculated slope of 5.8 mg per sq cm in aluminum, which corresponds to the Mn K doublet emission resulting from the capture of an orbital electron of Fe" by the nucleus. This shows that the radioactive species are the same in both slag and metal and identifies it as Fe55 Description of Individual Heats For the first heat, the radioactive iron was contained in the prefused slag. The active Fe55 had been precipitated with carrier and was added as Fe2O3 during fusion in the iron crucible. The charge of 500 grams of ingot iron was melted, the protective iron sleeve added, rotation started, and a prefused, inactive slag was added to allow the system to approach equilibrium. After about 5 min at temperature, the wash slag was skimmed and the active slag added. Initial slag and metal samples were taken as soon as the slag was molten. Additional samples were taken at indicated intervals thereafter. Slag samples were dipped with a small iron spoon and metal samples were sucked into 1/4 in. ID silica tubes. The slag and metal samples were pulverized and mounted for radioactive counting. The slag samples were analyzed chemically for FeO. Temperature was read after the last slag sample by immersion of a Pt-Pt-Rh thermocouple protected by a fused silica sheath. Since no significant variation of rate with temperature was observed

Jan 1, 1954