Search Documents

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By A. L. Field, P. H. Royster

The first report on the slag viscosity work of the Bureau of Mines was made by one of the authors1 in 1916. It was concerned chiefly with the method of measurement. A paper2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper3 was communicated to the Faraday Society. PuRpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was carly, observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al2O3), and silica (SiO2), provided the percentage

Jan 1, 1918

By J. Menashi, D. A. Douglas, A. S. Rappas

Aqueous solutions of Na2Cr04 are reduced with CO to produce hydrous Cr2O3 and NaHCO3/Na2CO3. CH3OH, HCOO- and HCHO in the presence of CO2 also reduce Cr(VI) and yield similar products. It is shown that the rate of Cr(VI) reduction can be represented by the expression -d [Cr(VI) ]/dt = k[Cr(VI)]0.5[R], where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mol (43,000 Btu per lb mol). Rapid reduction rates are attained at temperatures in excess of 220°C (428°F). With these three reductants, a green acid-insoluble readily filterable hydrous Cr203, is formed. With HCHO, significant reduction of Cr(VI) occurs at about 80° to 100° C (176° to 212° F). The product is an acid-soluble violet modification of hydrous Cr203. Solutions of Na2CrO4 contaminated with Mo(VI) and W(VI) can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels.

Jan 1, 1986

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry's position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry's position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

H. G. Haemers (Ghent University, Belgium)—The authors claimed "the results of their work indicate that the metals can be arranged in a sulfation series similar in its application for selective sulfation tot the electromotive series for displacement of metals from solution". The series as stated in decreasing order for tendency of SO3 give up, is the same as that stated by free energy diagrams. Indeed, the degree of stability of a sulfate is measured by the free energy of sulfate formation out of the corresponding metal oxide and SO3. The more negative the value of the free energy (-DG) the greater the stability of the sulfate. As a second consequence this statement results in a relative aptitude for capture of SO3 by each metal oxide when brought in contact with the sulfate of other metals. Let M1 and M1 be the two metals, and — DG1 and — DG2 their free energy values at temperature T. Both sulfates are stable at temperature T if - DG1 < O and — DG2 < O. In case where — DG1 < — DG2 the stability of M1SO4 is greater than that of M2SO4, and when M1O (oxide of

Jan 1, 1958

By Robert H. Carpenter

Major trends in exploration geochemistry during the past year included an increased level of geochemical exploration by both government and private industry: greater sophistication in sampling, analytical and interpretive techniques: and increased activity on the part of universities and state geological surveys. The evolution of applied geochemistry in North America from a useful prospecting tool to an invaluable exploration method is largely due to efforts of the mining industry, the USGS and the Geological Survey of Canada. In the U.S., there has been a distinct reluctance on the part of universities to conduct research or to offer courses dealing principally with applied geochemistry. Most university geochemists have not been responsive to industry needs because government sponsorship of geochemical research in universities has been overwhelmingly in favor of theoretical, rather than applied research: and, because of the mistaken notion that exploration geochemistry is not sufficiently academic. A critical shortage of specialists in this field has resulted. Specialists in Exploration Geochemistry Needed Based on the response to a brief questionnaire sent to universities in the U.S. and Canada, there is some evidence suggesting a reversal in this trend. Graduate courses devoted to exploration geochemistry are currently being offered in geology departments at the following universities: University of British Columbia, Colorado School of Mines, University of Idaho, McGill University, University of New Mexico, Pennsylvania State University and the University of Utah. Other departments report that applied geochemistry is included in general geochemistry courses. A survey of recent publications suggests increased research interest in exploration geochemistry by university geologists.

Jan 1, 1970

New York LOUIS D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. E. MALTBY SHIPP, Treasurer. GEORGE F. KUNZ, W. De L. BENEDICT. Boston ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston. Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH.

Jan 1, 1917

By E. B. REESER

EFFICIENCY is the foundation on which the prosperity of this Nation must be built. Your organization and the members thereof are constantly thinking of Gays and means whereby greater efficiency may be developed. It is often said that this Nation has become great because of its almost up limited supply of raw materials at low production &apos;costs. This was undoubtedly true in the earlier years but today we face an entirely different situation. We have learned that nature has been very generous in supplying all parts of the world with ample resources of various kinds to meet the demands. This applies to practically all commodities but for the purposes of this discussion, we will limit our remarks to petroleum.

Jan 1, 1931

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Dec. 10, 1914, to Jan. 10, 1915: William E. Saunders, Philadelphia, Pa. H. J. Brown, Chester, Pa. F. H. Winsor, Jr., Salt Lake City, Utah. H. Mortimer-Lamb, Montreal, Canada. Cecil W. Pocock, Peru, S. A. B. W. Vallat, Detroit, Mich. Willet G. Miller, Toronto, Canada. W. D. B. Motter, Jr., Benson Mines, N. Y Adolphe E. Borie has resigned as Chairman of the Board of Directors of the Taylor-Wharton Iron & Steel Co., to devote his time to the American Road Machinery Co. and the Good Roads Machinery Co., as Chairman of the Board of Directors.

Jan 2, 1915

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation&apos;s mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By J. S. Kennedy, A. A. Lerew, C. M. Judson, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from. these laboratories." These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that, are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren, machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as. the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite. flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the. selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pet Zn for ZnS) ; and the quartz from Klondike, Mo., analyzed as 99.97 pet SiO2. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from S82 supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1952

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation&apos; indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in&apos; all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest &apos;Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation&apos; indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in&apos; all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest &apos;Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By Frank G. Norris, William C. Marshall

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, &apos; others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By William C. Marshall, Frank G. Norris

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, &apos; others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By J. S. Kennedy, G. L. Simard, A. A. Lefrew, C. M. Judson, R. B. Booth

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.&apos;* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By J. S. Kennedy, A. A. Lefrew, C. M. Judson, R. B. Booth, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.&apos;* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953