Search Documents

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By Fred D. DeVaney

DURING the past few years a radically new process for the magnetic roasting of iron ores has been investigated and developed by Pickands Mather & Co. and the Erie Mining Co. in the Erie laboratory at Hibbing, Minn. This process, originally devised by Dr. P. H. Royster of Washington, D. C., involves the use of a roasting technique quite different from older methods. It has now been demonstrated that iron-bearing materials can be roasted as effectively as by any previously known method, and at a much lower cost. The increasing shortage of highgrade iron ores in this country has accelerated the search for new methods that would permit low grade materials to be utilized. The concept of magnetically roasting low grade nonmagnetic ores such as the oxidized taconites and then separating such material magnetically has always had considerable appeal. The magnetic concentration idea is attractive because of the sharpness of the separations and cheapness of the method. Heretofore, however, the equipment and the processes available for the magnetizing-roasting -step have left much to be desired. The customary equipment available for reduction roasting has been: 1-multiple hearth furnaces, 2-rotary kilns, and 3-shaft type kilns. In addition, it is understood that some work has been done in magnetically roasting fine ores by a process using the FluoSolids principle, but little information on this process is available. The multiple hearth kiln has been used the most but first costs and operating costs have been high because of low capacity, high maintenance, and poor gas utilization. Magnetic roasting can be done in a rotary kiln, but the radiation losses are high and the conversion to magnetite is usually unsatisfactory because of poor contact between the gases and the solids. Of the shaft-type furnaces, probably the most efficient yet developed is that designed by E. W. Davis of the Minnesota Mines Experiment Station. This furnace was operated at Cooley, Minn., during 1934-1937 but was abandoned in 1937 because the operation was uneconomic. Heretofore the basic concept behind most magnetic roasting processes has been the idea of heating iron ore to a temperature of 800° to 1100 °F in a strong reducing atmosphere, preferably either carbon monoxide or hydrogen. Temperatures under 800°F were undesirable since excessive roasting time was required. Temperatures over 1100°F were avoided because of the danger of converting part of the iron to ferrous oxide which is nonmagnetic. In the new roasting process, the operation is carried on in a shaft furnace using a controlled atmosphere containing a low percentage of reducing gas. The temperature in the roasting zone is considerably higher than with the usual reducing gas and this speeds up the reduction time. Portions of the spent furnace gases are cooled and recirculated and this together with the good contact between ore and gas makes for high reducing gas utilization. High heat economy is secured by recuperating heat from the roasted ore by passing the cold reducing gases countercurrent to flow of ore. The heat transfer principle is similar to that employed in a pebble stove and to that used in the Erie Mining Co. furnace at Aurora, Minn., for pelletizing fine magnetite concentrates derived from taconite. The theory of controlled atmosphere during the roasting operation can best be appreciated by inspecting the equilibrium diagram of the Fe-C-O system shown in Fig. 1. An inspection of this diagram shows that in certain areas magnetite, Fe3O4, is the only stable form of iron. A further inspection of this table shows that if the proper ratio is maintained between carbon dioxide to carbon monoxide, such a gas will be reducing with respect to hematite, Fe2O3, and will be oxidizing with respect to both ferrous oxide, FeO, and iron, Fe. It should be kept in mind that the formation of ferrous oxide in a roasting operation is harmful, since this oxide is nonmagnetic; if it forms in any quantity, it will cause substantial loss of iron in the ensuing magnetic separation step. If a ratio of approximately three parts carbon dioxide to one of carbon monoxide is maintained, the resulting operation can be carried on at a relatively high temperature without fear of over-reduction. Specifically, most of the tests in the Erie furnace have been made at a temperature of 1500° to 1600°F, with an entrant gas containing approximately 5 pct carbon monoxide and 15 pct carbon dioxide, with the remainder largely nitrogen. It should be remembered that the ratios of carbon monoxide to carbon dioxide shown in Fig. 1 hold even though the bulk of the gas is an inert gas such as nitrogen. It may surprise many to learn that a gas containing as low as 3 pct carbon monoxide, and 12 pct carbon dioxide with the remainder nitrogen is an extremely effective reducing gas in the 1000° to 1600°F temperature range. The reducing gas is not limited to carbon monoxide, and mixtures of hydrogen and carbon monoxide may be used effectively, provided that a similar ratio is maintained between the reducing gases and carbon dioxide and water vapor. For a more detailed explanation of the theory involved, the reader is referred to U. S. patents 2,528,552 and 2,528,553. From a safety standpoint, the weak reducing gas used in the furnace offers an advantage. Its composition is such that it is well below the limits of explosion should air enter a hot furnace. This condition is not true with the usual reducing furnace, in which a gas rich in carbon monoxide or hydrogen is used. The general furnace design and method of operation may best be understood by an inspection of

Jan 1, 1952

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS CHESTER A. FULTON, Chairman CARROLL A. GARNER H. Y. WALKER WALLACE E. PRATT FELIX E: WORMSER PAUL D. MERICA, Consultant FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERIE V. DAVELER, Chairman WILBER JUDSON RUSSELL B. PAUL HENRY KRUMB, Consultant

Jan 1, 1944

By Svend Rordam

THE development of a cement that will resist the destructive action of sea water and other corrosive waters is a problem that has occupied cement chemists for the past one hundred years. It has been found that of the various salts that commonly occur in corrosive waters, sodium sulphate, magnesium sulphate and magnesium chloride are most destruc-tive to cement. Many investigations have been carried out in the United States, in Canada, and in Europe to solve the problem of what constitutes a sulphate-resistant cement, and during the past 10 years some of the findings give definite information in this respect. COMPOSITION OF CEMENT Portland cement is composed of four major compounds: 1. Tricalcium silicate 3CaO.Si02 (C3S) 2. Dicalcium silicate 2CaO.Si02 (C2S) 3. Tricalcium aluminate 3CaO.Al203 (C3A) 4. Tetracalcium aluminoferrite 4CaO.Al203.Fe203 (C4AF) The two calcium silicates are the main contributors of strength. The tricalcium aluminate contributes some to the early strength of the cement but has the least resistance of the four compounds toward the attack of sulphate waters. The tetracalcium aluminoferrite does not contribute very much to the strength, but is far more resistant to sulphate waters than the tricalcium aluminate. When hardened cement is exposed to water containing sodium or magnesium sulphates, these salts will react with the hydrated tricalcium aluminate in the cement and form compounds that will cause a swelling, disruption and crumbling of the hardened cement.

Jan 1, 1939

By William Plank

IN PAST YEARS, engineering educators and others have been able to study the problems relating to en-gineering education in the United States with only inadequate and, frequently, inaccurate data at their command. For the first time there is now available fairly full and accurate information on this subject, gathered and compiled by the Board of Investigation and Coordination of the Society for the Promotion of Engineering Education. This board, of which W. E. Wickenden is the director, has for the past four years been carrying out fact-finding investigations into "the objects of engineering education and the fitness of the present day curriculum," under a grant of funds from the Carnegie Corporation of New York. Twelve bulle-tins have already been published by the board and others are in the process of preparation. The studies made, thus far, have been of the various phases of engineering education in general as well as of the major branches of engineering. Within the past year. the board has completed a study of mining engi-neering education by means of a questionnaire sent to members of the Institute. A special committee, con-sisting of Charles E. Locke, Allen H. Rogers and the writer, cooperated with the board in drafting certain parts of the questionnaire and in selecting the mailing list. Similar studies have been made through the mem-bers of the four other national societies. The results of these studies have been published only in mimeo-graphed form, therefore, in order to place the data before the members of the Institute an incomplete sum-mary of the replies to the A. I. M. E. questionnaire is here given. The full report will be available for distri-bution at the annual meeting in February. The questionnaire was sent to 306 members of the Institute, a proportion about equal to the proportion of the membership of the other national societies can-vassed; 152 members replied to the questionnaire, 55 per cent of whom had received college degrees in some branch of engineering connected with the mineral in-dustry. Forty-seven educational institutions were rep-resented in the replies. Seventeen different positions were held by the members who replied, with 24 con-sulting engineers at the head of the list, 20 managers, 16 superintendents, 11 presidents, 10 professors, 6 deans, and others.

Jan 1, 1928

By M. W. Bartley, Hugh M. Roberst

ERRATA In the paper (Mining Technology, January 1943) Page 19, second column. Line 5 should read: of Lower Huronian and Early Middle Huronian. Page 20, second column, line 17. Read magmatic solutions instead of magnetic solutions. In the discussion (Mining Technology, September 1943) On page 2 of this discussion pamphlet there is a typographic error. In the chemical analysis, the first reaction should read: CaCO3 + H2O = CaO2H2 + CO2 AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS

Jan 1, 1943

By J. Buchwald, R. W. Heckel

THE DeHoff method' of analysis of ellipsoids of constant shape provides a quantitative metallo-graphic technique whereby the actual size distribution of the ellipsoids may be determined from polished and etched random planar sections. This method provides a useful metallographic tool since it appears to be the only method available for determining the size distribution of nonequiaxed second-phase particles. This method, however, assumes that the type of particle being studied is known to be either oblate or prolate of a fixed minor to major axis ratio, q. This, in general, means that one assumes either oblate or prolate ellipsoids of a given q and checks the total volume and surface area of the second phase as determined from the particle size distribution to values of these quantities determined by other techniques. Suitable check methods may be point counting, lineal fraction, and areal fraction methods for obtaining the total volume and the Smith and Guttman2 method of intercepts for obtaining the total surface area. If the initial guess at particle shape and q were incorrect, i.c., the volume and surface information obtained from the particle size distribution data does not agree with those values obtained by other techniques, another assumption must be made and the particle size dist distribution must be recalculated. A current study in this laboratory has involved a large number of these calculations. To facilitate the handling of the calculations, the DeHoff method was programmed in the FORTRAN language for an IBM 1620 computer. The purpose of this note is to briefly describe this program. The complete program along with a list of variable names, a sample input, and a sample output may be obtained from the senior author. Basically, the program provides for the calculation of particle size distributions for a series of q values for both oblate and prolate ellipsoids for each set of input data. The total volume of second-phase particles per unit volume are calculated for each calculated particle size distribution. The output of the program is arranged to allow a rapid comparison of the calculated volume and surface values to data obtained by independent check measurements. A condensed flow chart of the program in the notation of DeHoff1 is given in Fig. 1 The calculation of the number of particles per unit volume in the jth size class, Ni, according to the DeHoff method' is: where k(q) is the shape-correction factor given by DeHoff as a function of q for both oblate and prolate ellipsoids, A is the size-class increment, k is the number of size classes, ni is the number of particles in the ith class on the planar measurement surface, and B(j,i) are the saltykov3 coefficients which correct for measurement surfaces which do not pass through the major and minor axes of the particles. The values of /3(j,i) are included as a two-dimensional array in the program. Particular values of k(q) are included in the program in increments of q of 0.05. The first calculation is carried out for q = 1 (spheres), the second for q = 0.95 oblate, the third for q = 0.95 prolate, and so forth. The number of q values chosen for the calculation is determined by a control card in the input for each set of data.

Jan 1, 1965

By J. Campbell

Various models are discussed for the evaluation of the negative pressures which may occur in solidifying materials which exhibit various deformation modes: elastic-plastic, Bingham, viscous, or creep flow. The inadequacy of the previously proposed elastic-plastic solution for solidifying metals is revealed by comparison with the more reliable creep results which are given graphically for aluminum, copper, nickel, and iron. The maximum tensions experienced in the liquid phase of solidifying spheres ranging in size from large castings to submicron powders are in the range from —10' to —105 atm for these metals. THERE has been much recent interest in the negative pressures associated with the volume change on solidification and in the possibility of the occurrence of cavitation. Considering the freezing of a highly supercooled liquid, an attempt to evaluate the stresses in the liquid ahead of the rapidly moving solidification front has been made by Horvay1 on a microscale and by Glicksman2 on a macroscale. In a casting of a wide freezing range alloy, the pressure differential due to viscous flow of residual liquid through the pasty zone has been discussed by Piwonka and Flemings,3 In a previous publication4 the author has attempted to estimate the negative pressure occurring in the residual liquid of a spherical casting, employing an elastic-plastic model to describe the collapse of the solidified shell under the internal tension. An earlier model assuming a rigid shell was shown to be inaccurate by many orders of magnitude. The elastic-plastic model is critically reviewed here, and other models are developed which are thought to be more closely related to metals and other materials near their melting points. The spherical geometry (Fig. 1) is chosen because the highest shrinkage pressures would be developed, although the analyses are readily adaptable to cylindrical geometry. A parallel sided casting experiences little internal tension because of the relatively easy dishing inward of the sides. (This commonly observed phenomenon has previously been attributed solely to atmospheric pressure.) Furthermore, small regions of confined liquid in a large solidified volume of a casting approximate reasonably well to spherical geometry. ELASTIC-PLASTIC MODEL The author has shown4 that as solidification proceeds the internal hydrostatic tension builds up until the elastic limit of the shell is exceeded. At this point the internal pressure is closely -2Y/3. Subsequently a plastic zone spreads from the inner surface toward the outer surface of the shell. When the whole casting is deforming plastically a rather more generalized analysis taking account of the externally applied pressure PA + 2y/b gives the internal pressure as: P = Pa + 2y/a + 2ys/b - 2 Y In(b/a) [1] The 2y/a and 2ys/b terms result from the tendency of the liquid-solid and solid-vapor interfaces to shrink, reducing their energy, and thereby helping to collapse the solid phase and compress the liquid phase. The 2y/b term would be important only for powders. The last term arises because of the plastic restraint of the solid, resisting collapse and so effectively expanding the residual liquid. From Eq. [I] it is easily shown that there is a minimum in the pressure at the radius amia= y/Y [2] which is of the order of 103K for the metals aluminum, copper, and iron, and corresponds to the minimum pressure Pmin = 2 Y[l-ln(bY/y [3] The results of a fully worked out elastic-plastic solution are given in a previous reporL4 The main criticism which may be leveled at this analysis when applied to metals at their melting points is the strong dependence of the yield stress on the strain rate. The strain rate varies with both solidification conditions (e.g., whether chill-cast or slowly cooled) and during solidification, as is indicated in the following section. Thus an appropriate choice of Y is very arbitrary. Before proceeding to a discussion of models which are strain-rate-dependent, it is necessary to evaluate the strain rate as a function of the rate of solidification. SOLIDIFICATION RATE Various empirical relations have been deduced5 for the rate of thickening of the solid shell by pour- out tests on partially solidified spheres. These, however, are unsatisfactory for our purposes since they become very inaccurate when the liquid core is very small. A theoretical approach is therefore necessary, and some solutions are set out below. Making the assumptions of constant surface temperature of the casting during freezing, no superheat, and a material freezing at a single temperature, Adams8 deduces the approximate solution: which becomes when b » a: Employing a semiempirical approach vallet6 finds:

Jan 1, 1969

By Arthur Notman

YEAR ago, the Committee on Mineral Economics ventured to predict a more realistic attitude by the public toward the folly of seeking to have more by making less under the guidance of the Blue Eagle. A unanimous decision of the Supreme Court of the United States has now laid that embattled bird to rest. De rnortuis nil nisi bonum. In spite of dire predictions of disaster to follow its early demise, the metal industries and many others have improved substantially. One could name many indications of that improvement, and on the strength of stock-market activities might assume

Jan 1, 1936

By John V. Beall

There was optimism on 14th Street on April 22, Earth Day. We only have the report second hand because the demonstration conflicted with another appointment. Fifth Avenue was closed to vehicular traffic from 14th Street to the Park for a few hours and the crowd that showed up to promenade rivaled anything that can be imagined, even one at a country fair in Merry Old England. Certainly the domestic animals were there and the costumes were wild-as they are almost any day on 5th Avenue. However, the mood was friendly, happy and optimistic according to one of our neighbors who filmed and taped interviews with some of the characters. People think the air is going to be clean, and the water pure in the future. Land is going to be treated with respect. Even if the demonstration temporarily fouled the streets with litter, it served the purpose of dramatizing awareness. In talking to our friend about his experiences we didn't miss the opportunity to sound out his impression of whether or not people recognize that no group of people nor industry has a monopoly on pollution.

Jan 1, 1970

By T. L. Joseph

A DEMAND for specialized knowledge has directed engineering curricula towards competency in some particular field or occupation. Preparation for life in a broad sense of completeness has received little consideration. Ways and means are needed for weaving some of the threads of liberal education into the fabric of engineering education. Any effort to develop a humanistic-social stem of engineering education will depend largely upon the content of the courses and the type of instruction offered. Many of the courses in college curricula are intended to lay a foundation for more advanced courses to be taken later by those. who specialize in some particular field. Students in other fields lack the background necessary to take the advanced courses and have too much detailed information, soon forgotten, forced upon them if they pursue the foundation courses. To develop a humanistic-social stem for engineering education existing catalogue courses selected should follow some general plan aimed towards broad educational objectives. Courses packed with detailed factual information are necessary for the stu-

Jan 1, 1947

[Trans. No.Place Date Vol. Page 1. Wilkes-Barre, Pa.* .... May, '71.. 1 8 2. Bethlehem Pa Aug., '71.. 1 10 3. Troy N. 'l Nov., '71.. 1 13 4. Philadelphia, Pa Feb., '72.. 1 '17 5. New York, N. Y.• ....May, '72 1 20 6. Pittsburgh, Pa Oct., '72.. 1 25 7. Boston, Mass Feb., '73.. 1 28 8. Philadelphia, Pa.' May, '73.. 2 3 9. Easton, Pa Oct., '73.. 2 7 10. New York, N. Y Feb.. '74 2 11 11. St. Louis, Mo' May, '74.. 3 3 12. Hazleton, Pa Oct., '74.. 8 8 13. New Haven, Conn....Feb., '75.. 8 15 14. Dover. N. J.' Mav. '75.. 43] [ ]

Jan 1, 1925

By AIME AIME

THE value to the engineering profession of a liaison between the engineering societies of Russia and America, through Engineering Council, was the subject of a meeting in the Engineering Societies Building attended by over 500 persons. In introducing the subject, Mr. N. A. Stephanoff, President of the Russian Society of America, said: In Russia, engineers were divided into two classes: those who had graduated from the high technical schools and the practical engineers who had graduated from special technical schools. These technical schools were divided into three groups: The first corresponded to the German polytechnical schools with many departments, mechanical, chemical, metallurgical, mining, etc. The second group corresponded to the French special schools of the "Écoles des Ponts et Chaussées." "École des Mines." The third group was formed by the Military and Naval Academies of Engineers. In 1910, Russia's high technical schools had about 45,000 students, whose training covered a period of not less than five years, and who enjoyed all opportunities afforded by laboratories in no way inferior to those of Germany.

Jan 1, 1920

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

References are in all cases to the earliest known editions. In the few cases where the first edition has been unavailable for consultation, the particular one studied is indicated. English translations are included when known, but not others. [ ]

Jan 1, 1942

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1916 to Dec. 31, 1916. BOWMAN, Joseph V., Chem., Andes Copper Mining Co., Chanaral, Chile, South America. CALDER, NORMAN L., Min. Geol., Cia. Minera y de Fomento, Watkins, Fomento Prov. de Santa Clara., Cuba. CONRADS, RALPH A., Met. Engr., Magna Plant, Utah Copper Co., Garfield, Utah. FARR, T. H. POWERS, JR. Asst. Assayer, Argonaut Mining Coy Jackson, Cal HAURY, PETER S., Min. Engr ...Alta Loma, Cal. HOULE, ARTHUR, Supt., Shattuck-Arizona Copper Co., Box 2009, Bisbee, Ariz. LEIB, VICTOR E?, Min. Engr 4204 Ave. D, Austin, Tex. LINDSLEY, THAYER, Min. Engr 82 Beaver St.,. New York, N. Y. POTTER, OCHA Supt., Superior Copper Co., Houghton, Mich. ROCCA, BERNARD T.; Engr., Bluebell Mine, Cons. Arizona Smelting Co., Mayer, Ariz. SAFFOLD, RAY P P.'0. Box 436, Douglas, Ariz. THOMS, JAMES EZRA, Asst. Chief, Milling, -Roasting, Acid Depts., Mineral Point Zinc. Co., Depue, Ill. TOMITA, HARUYOSHI, Met. Engr., Mitsubishi Co., Osaruzawa Mine, Akita-ken, Japan.

Jan 2, 1917

By K. A. Natarajan, I. Iwasaki

With a platinum electrode the Eh-pH response in aqueous systems follows an empirical relation [Eh = E- 0.059 pH](1) where E usually carries a value between 0.8 and 0.9 v. The same potential (E) is observed with a number of other noble metal electrodes in the absence of surface poisoning and of other well-defined redox couples. Many sulfide mineral electrodes also respond in a similar manner in solutions containing their respective ions over wide pH ranges, especially in the alkaline pH region. Such a parallelism between noble metal and sulfide mineral electrodes points to certain implications of their surface conditions, and the flotation and leaching behaviors of sulfide minerals under aerated conditions may be inferred with respect to the foregoing Eh-pH response. Comparison of Sulfide Mineral and Noble Metal Electrodes [Fig. 1] shows the Eh-pH response of pyrite, galena, chalcocite, and pyrrhotite electrodes, reported by Sato, and some experimental points obtained with a platinum electrode in distilled water. [Eq. 1] is seen to be followed by all these electrodes. It is interesting to note that the response of the pyrite electrode as shown is identical to

Jan 1, 1973

By A. H. Geisler, J. H. Keeler

Preferred orientations in rolled and annealed titanium sheets were determined by the Geiger counter spectrometer X-ray diffraction technique. Five annealing textures dependent upon the temperature range of annealing were found, and in order of increasing annealing temperature pendent upon the temperature range are: 1—a deformation like texture, 2—a rotated inorder a-recrystallization temperature texture, 3-a retained u-recrysraIlization texture, on annealing at lower temperatures of the ß-region, 4—a transformation texture based on recrystallized a and predicted by the Burgers' relationship, and 5—a ,ß-cube texture. These results are examined in terms of current theories of recrystallization textures. UMEROUS investigators have described the tex- ture obtained by cold rolling the hexagonal metals, titanium, zirconium, and beryllium, which have c/a ratios less than that of ideal packing, 1.633. The basal planes are rotated out of the rolling plane, about the rolling direction, so that the basal poles are tilted toward the transverse direction as shown schematically in Fig. la. In all instances but one,' it was also reported that the [1010] direction was parallel to the rolling direction (see Fig. lb). Hot rolling has been reported as causing a similar tilt of the basal poles in the transverse direction (see Fig. la) and causing the [1010] direction also to be parallel to the rolling direction as shown schematically in Fig. lb. Annealing after deformation does not appreciably change the tilt of the basal poles in the transverse direction." Beryllium2-7 continues to have the [1010] direction in the rolling direction after annealing, and similar observations for titanium and zirconium' . have been reported for annealing at fairly low temperatures, again as in Fig. lb. At higher annealing temperatures, however, the recrystallized grains of titanium" and zirconium have an orientation such that the [1120] direction is approximately in the rolling direction, although the basal poles are still inclined in the transverse direction. Figs. la and lc show the resulting orientations schematically. This change in orientation has been described as a nominally ±30° rotation of the hexagonal crystallites about the basal poles of the cold rolled texture and is apparent from the results which are summarized in Table I for investigations with the X-ray diffraction technique employing film. The angles y, , and ß are indicated in Fig. 2 which represents the stereographic projection of (1070) poles for the mean orientation of a pole figure. Texture determinations for titanium using the Geiger counter spectrometer have provided similar results except that in some instances additional components of the texture were proposed, as shown by the summary of data in the upper half of Table 11. On the other hand, the spectrometer technique, when applied to zirconium,* has revealed a splitting Recently completed studies of the textures of annealed zirconium", show zirconium to possess textures very similar to those reported here for titanium. Therefore, much of this discussion will include zirconium by virtue of its close similarity to titanium in pref erred orientations. of the intense areas of the pole figure for samples annealed at 600°C. This splitting could be described by a 7" rotation of the tilt axis about the normal to the rolling plane. Such a splitting for the annealed texture relative to the cold rolled texture was not observed in other determinations for either zirconium or titanium using the less sensitive film X-ray methoe and makes the relationship between the two types of texture more complex than the simple rotation about the (0001) pole based on film work. The more precise investigations on zirconium permit the descriptions in the lower part of Table 11, which show that the texture depends quantitatively on the temperature of annealing. When zirconium is annealed at temperatures up to 400°C, the texture is similar to the cold rolled texture, while annealing in the range 500" to 900°C produces a texture which is only approximately described as [11%] in the rolling direction. More precisely described results for zirconium show that the two types of splitting ( 1—about an axis in the rolling plane through an angle given in the second column in Table II and 2—about the normal to the rolling plane through an angle given in the third column of Table 11) depend on annealing temperature. The [1120 is the rolling direction only when the annealing temperature is in the vicinity of 900°C

Jan 1, 1957