Search Documents

By H. Reiss

The zone-melting process in which redistribution of solute in a solid bar is effected by the passage of a molten zone is considered mathematically. Simple approximate techniques are developed for computing the manner in which redistribution occurs as molten zones continue to pass. The introduction of the "zone-melting flux" provides valuable insight into the nature of the phenomenon, as well as a central mathematical theme in terms of which the process can be discussed. Curves are presented for typical and general cases. AN extremely efficient purification technique was described recently by Pfann.1 Known as zone refining, it consisted of the slow passage of a series of molten zones, produced by external heaters, through a long solid ingot of the substance to be purified. Equations were given for the maximum separation attainable, and a numerical computation method was described for obtaining the concentration in the ingot after a given number of zone passes. The present paper offers an interpretation of the physical nature of zone melting in terms of a transport process in which formal diffusive and convec-tive flows occur. This interpretation, in addition to providing insight into the physical nature of the process, also provides a basis for its mathematical treatment. From this basis, useful equations are developed for the solute concentration in the ingot as a function of the number of zone passes. These are applicable particularly where large numbers of passes are necessary and where numerical computational methods might be laborious. All considerations will deal with the limiting form of the process, described by Pfann,' in which: 1—Diffusion in the solid is considered negligible. 2—Mixing in the liquid is supposed, complete. 3—The distribution coefficient, k, measuring the ratio (at equilibrium) of solute concentration in the solid to that in the liquid is supposed, independent of composition. In general, this paper will be concerned with a bar of uniform (actually unit) cross section, ex- tending in the x-direction from x = 0 to x = L, where L may be infinite. Zone melting is a transport process, and as such must admit of interpretation in terms of a flux of transported quantity. However, the progress of operation is not measured in units of time but in terms of the number of completed zone passes. Consequently, the zone-melting flux will be a rate, per unit pass, rather than per unit time. The description of this flux and the examination of its properties is given below. Zone-Melting Flux Fig. 1 represents an intermediate stage of the nth pass. Concentration C is plotted against distance, x. The molten zone with its back at the point x and front at x + I moves in the direction indicated by the arrow. As it moves, it leaves behind the nth

Jan 1, 1955

By Thomas M. Drown

The process for determining phosphorus in iron now in most general use in the laboratories of iron and steel works, is, I think, the one proposed bv Mr. Emmerton." In this process the solution of the iron for precipitation by ammonium molybdate is effected by treating the iron with nitric acid, evaporating to hard dryness in a dish, taking up with hydrochloric acid and driving off the greater portion of the hydrochloric by nitric acid. This procedure accomplishes, first, the destruction of all the carbonaceous matters; and, second; it renders all the silica insoluble. Experience has proved the former—the complete oxidation of the carbon—to be absolutely essential; but the explanation usually given, namely, that unless the carbon compounds are destroyed they will have a solvent action on the yellow precipitate, I am inclined to

Jan 1, 1890

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By M. J. Humenick, K. Garwacka

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia that may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of injecting high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final cleanup process for ammonia removal from the ground water system. This paper details ammonia removal efficiency as a function of chlorine dose, reactant, and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1985

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis- charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed arid built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, anti not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct the grinding and classification test program. It was the author's privilege

Jan 1, 1939

By J. B. Neale

FRom the beginning of its activities, the members of the National Production Committee have felt that the following points were essential to the success of its work: The operators must feel that their operations were not 100 per cent. efficient; that they should be courteous and fair in their treatment of their employees; and that they should set an example of hard work and patriotic interest in increased production. Every move made must appeal to the sense of fairness of all parties concerned. The men must feel that in working more faithfully, and consequently producing more coal, they are rendering a distinct service to their Government in the time of its great need. As the workers feel that greater efficiency on their part results only in greater profits to the operators, the advantage to the operator should be lost sight of, as far as possible, and the advantage to the Government in fighting the war emphasized. Both operators and workers should know that the Government considered increased production an obligation, and opportunity for service, resting on both parties and not on the operators or the workers alone, and that both parties could very much better the efficiency of the pre-war period. Had the committee intimated that it thought the coal shortage was due entirely to the idleness and inefficiency of the workers, its campaign would have failed, for the men would have resented the charge because only too frequently their efforts to produce more coal were thwarted by bad management; besides, the operators would have lacked stimulus to better effort. On the other hand, had the impression been given that the committee thought that the coal shortage was due entirely to bad management, the operators would have resented the charge because only too frequently their efforts to produce more coal were thwarted by the idleness and inefficiency of the workers; and the workers, having been thus indirectly pronounced 100 per cent. efficient and patriotic, would have lacked stimulus to better effort.

Jan 1, 1920

By Larry G. Hayes

Development of the Bowers-Campbell zinc deposit, located in the Shenandoah Valley two miles northwest of Timberville, Va., was commenced in 1956 by the Tri-State Zinc Co. The occurrence of lead-zinc mineralization in this area has been known for many years, but the first serious exploration program was initiated in 1951 by the geologic staff of Tri-State Zinc Co. Ordovician dolomites. The deposit is approximately 700 ft long, 100 ft wide, and 475 ft thick. Its projected plan has an elongated ovoid shape, where- as the profile appears boot-shaped with the upper portion outcropping. Vertical cross sections show the lense as having been thrust-faulted along certain bedding planes. The movement along these bedding thrusts varies greatly and in one case, has offset the deposit so as to divide it into an upper and lower orebody. The breccia lense strikes parallel to the N 34" E strike of enclosing strata.

Jan 9, 1960

By W. M. Rust, W. D. Mounce

THE almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubt- less other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations.

Jan 1, 1944

By W. G. Pfann

Under certain conditions, a molten zone can be made to move through a solid by impressing a stationary temperature gradient across the solid. This phenomenon can be utilized in fabricating semiconductive devices, growing single crystals, joining, boring fine holes in solids, measuring diffusivities in liquids, small scale alloying, and purification. Fundamentals and exemplary applications are outlined. ANEW aspect of the travel of a molten zone through a solid is considered in this paper. Whereas, in previously described zone melting techniques,'-' zones were usually caused to move by changing the position or temperature of a heat source, in the present technique a zone is made to move by impressing a temperature gradient across it. For example, a thin layer of molten A1-Si alloy, sandwiched between two silicon slabs having a temperature gradient normal to the layer, will travel through the hotter slab. One feature of temperature gradient zone melting, as this technique will be called here, is that zones of unusually small dimensions can be maintained. This leads to such diverse uses as have been listed in the abstract. In this paper fundamentals of the movement of a molten zone in a temperature gradient, and some practical applications thereof, are outlined. Assumptions The movement of a molten zone through a solid body of solvent substance in which a temperature gradient exists will be discussed. The length of the zone will be its dimension in the direction of motion. The direction of the temperature gradient will be toward the region of higher temperature. To be considered is a binary or higher order solute-solvent system in which the concentration of solute in the molten zone is sufficient to produce a lowering of the freezing temperature of the solvent which is at least of the order of the temperature range impressed on the charge. While we discuss primarily molten zones in a solid matrix, the principles are applicable to solid or vaporous zones in a solid matrix, a requirement being that the diffusivity in the zone be substantially greater than in the matrix. Diffusion of solute into the surrounding solid will be assumed negligible. In general, its presence will not basically alter the conclusions to be drawn. For illustration, a system represented by the partial constitutional diagram of Fig. la will be discussed, in which k, the distribution coefficient defined in the figure, is constant and less than unity. However, the technique is applicable to any solute- solvent system in which one component lowers the melting point of another component. Movement of a Molten Zone in a Temperature Gradient Consider, in the system AB of Fig. 1, where B is designated the solute and A the solvent, the effect of sandwiching a thin layer of solid B between blocks of solid A and placing the whole in a temperature gradient such that the temperature of the layer is above the lowest melting temperature of the system. Surrounded by an excess of A, the layer will dissolve A, becoming molten, and expand in length." As so- lution of A continues, at both interfaces, the mean solute concentration in the zone will move to the right in Fig. la, until at temperature T, the liquid at the cooler interface reaches the liquidus concentration C,. Solution of A thereupon ceases because the liquid T1 is saturated with A. The liquid at the hotter end of the zone, being at temperature T2, is not saturated with A at concentration C1. Hence solution of A continues there and concentration C2 is approached. A concentration gradient therefore is set up in the zone, causing A to diffuse toward the cool end and B toward the hot end. As a result, the liquid at the cool interface becomes supersaturated and a layer of crystalline A containing concentration kc, of B in solid solution freezes. Since a source of A

Jan 1, 1956

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

By H. Larson, J. Chipman

The ferrous and ferric oxide concentrations of slags, expressed as j = Fe+++/(Fe+++ + Fe++), have been established through gas-slag equilibrium at 1550°C in a range of oxygen pressure of 10-I to 10-9 equilibriumatm. The value of j is increased by basic additions (BaO, CaO, MgO, MnO) and decreased by acidic oxides (SiO2 and TiO2). Oxygen pressure is shown graphically as a function of composition for slags which are analogous to those at the slag-gas interface of the open hearth furnace. THE progress which has been made in recent years in understanding the chemistry of metallurgical slags has been based largely on studies of slag-metal and slag-gas equilibria. There is a considerable body of knowledge which is applicable to reactions occurring at the slag-metal interface in open hearth steelmaking. There is little information concerning reactions of the slag with the furnace atmosphere and hence little basis for an understanding of the transfer of oxygen, sulphur, or hydrogen between gas and slag. The oxygen pressure of the open hearth atmosphere is normally of the order of 10-1 to 10-3 atm which differs by several orders of magnitude from that of about 10" atm at the slag-metal interface. The chemical properties of the slag, for example, the ratio of ferric to ferrous iron and the ability of the slag to hold sulphur in solution, are greatly affected by changes in oxygen pressure. This investigation was undertaken to enlarge our knowledge of the effect of oxygen Pressure on steel-making slags. Using air or controlled mixtures of CO a CO2 a range of oxygen Pressures from 10.' to 10.' was covered. Review of the Literature There are only a few references in the literature which pertain directly to this investigation. The most important is that of Darken and Gurry1,2 on the system iron-oxygen. This work included the determination of the phase diagram of the system and also a study of the field of homogeneous melts and their oxygen pressures. Their apparatus and procedure were very similar to that used in this study. Iron oxide was melted in a platinum crucible under an atmosphere of CO2:CO, CO2:H2, H2O, CO2, air or O2 depending upon the partial pressure of oxygen desired. After equilibrium was reached, the sample was quenched and analyzed for ferrous and ferric oxide. By appropriate calculations these authors were able to determine the oxygen and iron activities in the various slags, heats of formation of the oxides of iron, and heats of solution of iron and oxygen in the liquid slags. In a subsequent paper' the same authors made a less thorough investigation of the effects of additions of lime and manganese oxide on the composition of iron oxide melts. Only a few experiments were made and those in a narrower range of temperature and oxygen pressure. Darken' has investigated the fusion temperature of iron oxide in contact with silica under various atmospheres. He found that the temperature changes from 1120° to 1447°C as the gas composition changes from CO2/CO equal to 20.8 to pure oxygen. A comprehensive paper by White" predates the work of Darken and Gurry. The decomposition of ferric oxide into oxygen and lower oxides of iron was studied from 1000° to 1650°C and under oxygen pressures from 2 to 76 cm of mercury. The effect of

Jan 1, 1954

By Arthur W. Ruff

One of the major challenges to management in the mining industry today is the establishment and maintenance of positive and dynamic programs for cost control and cost reduction. To meet the challenge, management must have a good cost system. There are various types of cost accounting systems in use today: some companies check their, performance by comparing the costs incurred during one period with the costs incurred during previous periods, while others compare the current costs with estimated costs which the company considers desirable. A third type of system is a standard cost system which provides predetermined allowances for the various cost elements and operating activities. Such a system, based on sound standards, can be established to fix responsibility for cost performance in each segment of the operation; recognize the impact of volume or rate of activity by establishing a standard volume and evaluating departures: take into consideration fixed and variable costs and their dissimilar behaviour at varying levels of operations: and provide consistent and equitable yardsticks for measuring performance.

Jan 11, 1962

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg2SiO4) and fayalite (Fe2SiO4) in solid solution. The name olivine was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Olivine is the principal component of the rock dunite, which itself is a member of the peridotite group of ultrabasic igneous rocks. European uses of the terms olivine and dunite are somewhat different than US usage. In commerce European usage defines dunite as containing 36 to 42% MgO, 36 to 39% SiO2, and loss on ignition of approximately 10%. The term olivine is used to designate a material containing approximately 85% forsterite, with a chemical composition of approximately 45 to 50% MgO, 40 to 43% Si02, 5 to 8% Fe2O3, and ignition loss of 1 to 2%. Uses The principal use of olivine is in various applications involving hot metal. Table I shows the best estimate available as to the amount of olivine consumed by various industries worldwide. In excess of 90% of world uses involve hot metal, with approximately 75% as a slag conditioner in the blast furnace production of pig iron. Approximately 15% of total olivine usage is as a special foundry sand in mold making for the brass, aluminum, magnesium, and manganese steel foundries (Schaller, 1957, 1958; Snyder, 1957; Anon., 1977). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as hand-cobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, has found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). The use of olivine as an additive in the blast furnace is relatively new, having been developed during the last decade. J.W. Currier (Private communication, 1978) describes the behavior of olivine in the blast furnace as follows: Olivine (Mg, Fe2, Si04) represents a unique lime-free source of magnesia and silica as a blast furnace charge component. Only recently has the magnesia-rich mineral been recognized as beneficial cleaner for blast furnace experiencing the problems associated with excessive alkali inputs and/or low coke stabilities. For some time it has been known that alkalis tend to recycle and accumulate in blast furnaces. In the high temperature region of volatilization the elemental alkalis formed attack the integrity of the graphite structure. This alkali attachment is enhanced when poor coke is used. Higher in the furnace stack volatile alkali cyanides condense and oxidize. This accumulation of alkalis tends to agglomerate the burden materials, producing scabs and scaffolds. These structures not only inhibit the downward movement of burden materials and the upward passage of wind, but also lead to erratic furnace performance

Jan 1, 1983

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By Paul J. Bennett, James E. Castle

The sillimanite family of minerals, including kyanite, sillimanite, and andalusite, are anhydrous aluminum silicates with the formula A12O3-SiO2. Dumortierite and topaz are also included in this group because they are closely allied in composition and thermal behavior. However, neither are mined commercially today. They are typical metamorphic minerals which are found in metamorphic rocks on every continent. Sillimanite minerals are prized chiefly for their refractoriness and are important components in a broad range of acid refractory products, especially in mortars and castables. World production of sillimanite minerals is currently about 400,000 tpy and has been increasing at the rate of 3 to 8% a year for many years (Anon., 1972). While these minerals have widespread occurrence, the consumption of sillimanite minerals is concentrated in the relatively few highly industrialized areas where refractories are manufactured, and which in turn are typically close to the major iron and steel producing regions of the world. Thus northern Europe,. England, the United States, and Japan are the principal consumers of refractories and sillimanite minerals. Of these countries only the US is a significant producer. Uses of Kyanite The following specifications are typical for the domestic kyanite industry: Raw Kyanite Concentrates Chemical Analysis 56% AI2O3 min 0.1% CaO max 42% SiO2 0.1% MgO max 1% Acid soluble 0.3% combined Fe2O3 alkali max 1.2% TiO2 max Available Sizes 35, 48, 100, 200, and 325 mesh The largest use for domestic kyanite, both raw and calcined, is in the manufacture of refractory mortars, cements, castables, and plastic ramming mixes. In these applications kyanite constitutes from 10 to 40% of the mixture, the balance being refractory clays and coarser grog materials. A certain proportion of raw kyanite is used to offset the shrinking of the clay binder, whereas the calcined kyanite is used in the coarser sizes for body. Certain high grade refractory shapes and kiln furniture are composed chiefly of graded sizes of calcined kyanite bonded with a little ball clay. In most applications, however, kyanite is used only to fortify the mix or as a minor ingredient. Some manufacturers of mullite brick use domestic calcined kyanite for the fine-grained portion of the brick, but seldom in quantities exceeding 10% by weight. Kyanite is used by ceramic manufacturers of wall tile and sanitary ware to offset shrinkage and cracking after firing. Indian kyanite has traditionally been used to make the coarse grog sizes needed for the manufacture of mullite brick, and for the grog portions of mortar, cement, and castable mixes. It has been largely replaced, however, by synthetic mullite, high fired flint, and diaspore clay or calcined bauxite for other applications. Indian kyanite has been available in lump as well as in granules and concentrates, as are sillimanite materials from India and South Africa. Andalusite is available as 8 mesh granules and as fines with chemical analyses not unlike those of domestic kyanites. From time to time and from place to place minor amounts of other aluminum silicate minerals such as dumortierite, topaz, and pyrophyllite have been made available at various prices and specifications, but have not been significant factors in the refractory industry. A mixture of kyanite and sillimanite of relatively fine grain-size and of low iron content was at one time offered to the molding sand industry by the Du Pont Co. as a byproduct from their deposits of heavy

Jan 1, 1983

By Alan Morris

In a previous paper1 the results of cutting tests on free-cutting brass rod were reported. Investigation was made of the effects of variation in lead content, microstructure and cold drawing. The author's reply to the discussion of that paper includes a study of the directional cutting properties of drawn and annealed rod. The present paper records the results of tests made on series of samples in which the tin, iron and copper contents have been varied. The apparatus used and method of testing are described in detail in the previous paper. The machine is of the pendulum-operated milling type used and described by Airey and Oxford.2 Angular readings of the height to which the pendulum rises after falling from a fixed position, both when a cut is made and when the pendulum swings freely, give the basis for calculation of the energy consumed in making a cut. Careful weighing of the sample before and after cutting gives a measure of the amount of metal removed. The results are expressed in footpoiinds per cubic inch of metal removed, and have been called "unit cutting energy." In the course of the discussion of the author's earlier paper, W. B. Price reported large-scale tests involving some 50,000 lb. of material. These tests indicated that the addition of as much as 0.6 per cent of iron and 0.25 per cent of tin had apparently no adverse effect on the highspeed cutting characteristics of the rod. The rod also contained a small amount of nickel. The test results reported here tend to confirm his observations. Effect of Variation in Tin Content The castings for this series were made 2 by 1 by 9 in. and were processed as follows: 1. Castings were annealed at 500" C. for 7 hr. 2. Cold-rolled to 0.700 in.

Jan 1, 1933

By Thomas W. Healy

Particles present in mineral processing systems that are termed ultrafine are those that are small enough to be unaffected by gravity or the flow conditions imposed on the pulp. As such, their interaction with one another and with other larger particles are controlled by specific attractive and repulsive colloidal or surface interactions. Electrostatic repulsion between ultrafines is dominated by surface potential, double layer thickness and specific adsorption potential effects - controlled by pH, salt and complexing ion concentrations. Attraction due to van der Waals interactions must be assessed in terms of bulk and surface coating effects and of particle size and shape. The net effect of attraction and repulsion must finally be related to the average kinetic energy of particles in the real system.

Jan 1, 1979

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) THE tabular statement accompanying this note shows the money cost in each of the three departments of manufacture, of 17 leading items, and also the proportion (expressed in a decimal fraction) which each of these items bears to the total cost. The statement can hardly be taken for more than an average illustration of the clear showing of ratios and of results which may be made by such an arrangement, for not only will these items vary from month to month in any given works, but the methods themselves of manufacture differ widely in different works. It is obvious that such a statement, however useful it may be, must be submitted with but exceedingly little explanation or discussion, or with none at all, for the reason that to enter at any satisfac-

Jan 1, 1878

The Army Reorganization Act, which became effective July 1, 1916, contains a provision authorizing the organization of an Officers' Reserve, in which will be included a Corps of Reserve Engineers. There will also be an Enlisted Reserve of skilled workmen in technical lines. The special provisions of the bill relating to the Engineer Officers' Reserve were formulated with the help of the Joint Committee of the several national engineering societies, which has been at work on the matter for over a year with the War Department and Committees of Congress. Recognizing that engineering science is the basis of success in modern

Jan 8, 1916

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952