Search Documents

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By Cyril Smith

A COMPLETE discussion of the literature on the subject of the influence of copper on iron and steel will be published elsewhere.1 The present paper is concerned especially with the precipitation-hardening of copper steels, and brief mention will be made here only of the work of Kin-near,2,3 Nehl4 and Buchholtz and Koster,5 who alone have studied this phase of the subject. Kinnear found that normalized low-carbon steel castings containing about 1.0 per cent copper on drawing at temperatures in the neighbor-hood of 530° C. (1000° F.) increased in tensile strength and yield point, with little decrease in ductility. The maximum effect was obtained with about 0.9 to 1.0 per cent copper, and when the copper exceeded 3 per. cent no improvement occurred on reheating. Kinnear did not study the effect of time of reheating-an all important factor where precipitation is concerned. Nehl,6 who apparently was unaware of Kinnear's work, recognized the change as due to precipitation and studied the interdependence of time and temperature of reheating, the temperature of the initial solution heat treatment, and the speed of cooling necessary to retain the bulk of the copper in supersaturated solu-tion and to give an increase in hardness and tensile strength on reheating. Nehl found that if the final rolling or forging temperatures exceeded 700° C. (1300° F.) it was not necessary even to normalize the steel, but full precipitation occurred on merely reheating the forged or rolled shapes at 500° C. (930° F.).

Jan 1, 1933

By F. J. Fayers, R. L. Perrine

For many years the problem of increasing ultimate recovery of oil from a reservoir has been a subject of interest to the oil industry. At present, a standard secondary recovery technique is to flood the reservoir with water once natural forces of the system are depleted. The permeability characteristics of the rock, together with interfacial forces which exist between the two fluids and the porous material. allow only part of the oil in the rock formation to be recovered by the water-flooding process. Laboratory experiments have shown that when detergents are added to the flooding water, the flow properties of oil in a porous rock arc improved. This improvement results in greater oil recovery. Even though higher recoveries are obtained using detergents, the extra cost associated with the method may make it economically unsatisfactory. To establish economic feasibility requires experimental laboratory measurement of fluid and rock properties together with a calculational procedure to predict field results. Pilot tests in the field may also be required. This paper presents a mathematical procedure for predicting detergent flood behavior. A number of reasonable simplifying assumptions are made to obtain a tractable system of equations. The resulting method may be regarded as a generalization of Buckley-Lev-crett' theory to solve simultaneously for water saturation and detergent concentration profiles. Consequently this type of calculation can be used in much the same manner as Buckley-Leverett theory is used to evaluate a water flood. The mathematical method employed is the so-called method of characteristics for solving hyperbolic partial differential equations. This application of the method is instructive because several other problems in reservoir analysis may be analyzed in a similar manner. FLUID FLOW EQUATIONS The flow behavior of oil and water without detergent through porous reservoir rock is usually expressed by Darcy's law and a continuity equation for each phase. If gravitational forces are neglected, vrg = kr (s)µr v p rg.........(1) vrg = kr (s)µr v p rg.........(1) ? pa va = F ?/?t (sd) where v is the volumetric flux, k represents permeability, S is saturation, and P the pressure. Fluid viscosity is denoted by 11, p is the density, 4 is porosity, and I the time. The subscripts w and o refer to water and oil. The capillary forces in the system lead to a difference in pressure between phases. This may be expressed by the relation: Pm -P0 =Pc(S).........(5) The capillary pressure? P,, is determined experimentally as a function of saturation. DETERGENT BALANCE EQUATION Addition of detergent to the water phase affects the flow properties of the system. Capillary pressure and relative permeability become functions of detergent concentration, c, as well as fluid saturation. That is: P--P (S,c) and k,,,.- - -- k,,,. At low oil saturation values, the presence of detergent reduces capillary pressure and reduces the relative permeability ratio. Detergents are surface-active and adsorb on rock surfaces. The quantity adsorbed, a, will depend on the concentration c of detergent solution and may also depend on the saturation; thus, a = a(S,c). In this analysis we have assumed that the detergents used are water soluble but not oil soluble, and their movement is therefore restricted to the water phase. The dispersion of detergent in water is neglected by comparison with transfer by flow within the system. Detergent movement is determined by the water flux and adsorption: ? cv m = -F ?/?t (cs + a) We will assume that the quantity of detergent in solution is too small to significantly change water density or viscosity. When the permeability and capillary pres-

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By J. Blodget Britton

To the question, " Do the Pennsylvania anthracites contain phosphorus?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Ironmasters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows : Ash. Phosphorus. No. 1, . 4.10 .0063 2, . . . . 7.97 .0209 113, . 5.53 .0049 114, . . . . . . . 6.55 .0056 . 5, . 5.39 .0761 . . . . . . . 11 6, 14.15 .0593 7, . 10 43 ,0049 rl 8, . . . . . . . 5.29 .0354 9, . . . . . . . 3.01 .0042 6L10, . . . . . . 3.03 .0042 1 1 . 275 .0014 12, . 2.82 ,0111 l'13, . .3.69 trace L1 14, . . .2.35 trace 15, . . . . . . . 7.22 .0014 16, . . . . . . . 3.49 .0167 17, . 4.63 trace

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.',' Initial work by Pye' indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By J. C. Yannopoulos, N. J. Themelis

Ah electronic thermogravirnetric balance was used to measure the veductioiz rule o single cirpric oxide particles suspended in a stream of hydrogen. Very jzne thermocouples embedded in lie center and at the surface of the sphere recorded the variation of terw perature during reduction. In contrast to iron oxide reduction, where in most instances the rate of interface reactiokl is controlling, the heat- and mass-transfer phenotnena play a predolrinant role in the reduction of cupric oxide. The correlation of experitnental data or tnass lransfev lhrough the boundary layer at Reynolds nunlber 0-4 50 was as jollocs: ThE reduction of cupric oxide by hydrogen is represented by the equation: It is a highly exothermic reaction and the amount of heat released varies only slightly with temperature (-21,430 cal per g-mole at 400°C). Most of the published studies on this system have been conducted at temperatures in the range of 34 to 280c.l-&apos; The concensus of opinion has been that at temperatures below 200°C the reaction is preceded by an induction period during which there is very little or no reduction. The length of this period diminishes as the temperature of the reaction is increased1l5 and aseawa found that at 280°C reduction starts practically immediately when the oxide is exposed to hydrogen gas. The existence of an induction, or incubation, period has led experimenters to believe that the reduction of CuO by hydrogen is catalyzed by metallic copper.&apos; Boldurev and rmolaev found that mechanical additions of powdered copper to oxide did not affect its reduction, although metallic copper produced during the reduction seemed to have a catalytic effect. At least three other authors2&apos;5&apos;7 have reported that addition of copper had no effect on the rate of reduction. Pease and alor&apos; observed that water vapor had a strong inhibiting effect on the reduction at 1503C, but its effect was greatly diminished at 200 C. Pavlychenko and Rubinchik5 studied this reaction at 159 to 235 C and found that, once the reaction had been initiated, there was no inhibiting effect due to the introduction of water in the hydrogen stream; at temperatures above 183°C there was no inhibiting effect due to water vapor, either before or during reaction. The same authors noted that the rate of reduction was independent of pressure in the range of 200 to 700 mm Hg. aseawa investigated the kinetics of the CuO-Hz system at 160 to 280°C and estimated the apparent activation energy at 14,000 cal per g-mole. A similar value (13,500 1200 cal per g-mole) was reported by ond&apos; in the temperature range 148 to 216°C. Bond also reported that there was no incubation period and that water vapor had no inhibiting effect on reduction at temperatures above 190 C. The above studies have been conducted at temperatures below 280°C and the physical configuration of the system under investigation has not been defined adequately. However, it is well-known that the mechanism of gas-solid reactions depends on a number of in series physical and chemical rate prcesses.&apos;&apos; It is, therefore, essential to include among the experimental factors the geometry of the solid system and the mass-transport characteristics of the reducing gas. Scott studied the reduction of packed beds of cupric oxide cylinders by Hz-He streams of very low hydrogen concentrations at temperatures 400 to 600 C, pressure of 10 to 30 atm, and gas velocity from 0.18 to 5.8 ft per sec (3 < Rep < 30). The reduction rate was found to be mainly controlled by diffusion through the boundary layer and through the pores of the reduced copper phase. The following correlation was proposed: Scott in an earlier work studied the reduction of fixed beds of cupric oxide wire and found that the rate of flow of the gas stream through the bed had a controlling effect on the rate of reduction. The same mass-transfer phenomenon was observed by Bond and clark13 on a similar reduction system. The analogy between mass and heat transfer through the boundary layer which exists between a solid surface and the bulk stream stems from the similarity of the differential equations representing these phenomena

Jan 1, 1967

By Donald F. Kennedy

During the past several years Climax Molybdenum Co. has been engaged in testing various types and sizes of hollow drill steel. The majority of tests have been on 7/8-in. hexagon st.ee1, inasmuch as it represents approximately 70% of total drill steel consumption at the Climax operation. Prior to December 1960, tests on 7/8-in. hexagon drill steel were conducted on steel with a forged collar and, in most cases, with a threaded bit connection. Through these tests and research, some improvement in steel life was achieved by making changes in heat treatment, design and alloying constituents. However, during that month, research and testing commenced on a rubber collar which was designed to replace the forged collar on 7/8-in. hexagon drill steel. Manufactured by the LeRoi Div. of Westinghouse Air Brake Co.. the collar. is very simple in design, consisting of a 1 ½ -in. diam steel cylindrical sleeve 2 in. long, containing a bonded rubber insert and attached to the steel with an epoxy cement

Jan 8, 1962

With a mine output as high as 5000 tpd and mill capacity of 7000 tpd, the uranium mining and milling complex owned and operated by Kerr-McGee Nuclear Corp. in the Ambrosia Lake area is the largest in the U.S. and is likely to remain so for some time. Next year, Kerr- McGee expects to have in production another mine in Section 19 of the Ambrosia area-and will begin ore production in 1976 at its new $15-million mine at Church Rock, located northeast of Gallup, N. M., where the company has already completed the shaft work and is in the early stages of project development. Ore from Church Rock will be transported to the company&apos;s facilities at Ambrosia Lake for processing. Kerr-McGee&apos;s existing eight mines in Ambrosia Lake go to depths of about 800 to 1500 ft to tap the various horizons of uranium-bearing sands in the Westwater Canyon of the Morrison formation.

Jan 8, 1974

By Rudolph G. Wuerker

MUCH descriptive matter[ ] has appeared on the subject of suspension roof supports, or roof bolting, as it is more commonly called. The wide- spread introduction of roof bolting into coal mines and metal mines is truly phenomenal. Mine operators were quick to recognize the advantages of supporting wide openings without hindrance to machine maneuverability and ventilation.

Jan 6, 1953

By F. R. Brotzen, D. L. Davidson

ALTHOUGH much effort has been devoted to the problem, the nature of plastic flow in bcc metals is still not fully understood. Some of the difficulties encountered stem from the scarcity of information on orientation effects and the uncertainty as to the glide system in these metals. In an attempt to provide some of this information, the present investigation was carried out, using zone-refined molybdenum single crystals deformed in tension and in direct shear. Considerable evidence exists to indicate that the primary slip system for molybdenum is (110) <111>.1,2 Figs. 1 and 2 indicate that this is, indeed, the case for direct shear at room temperature (see Ref. 3 for a description of the shear-testing equipment and procedure). Moreover, from Fig. 2, the shear stress on the (123) is lower than that on the (112). This would be the case if, as has been suggested,4,5 slip on these two planes is in reality com-

Jan 1, 1965

THE CHAIRMAN (F. K. COPELAND,* Chicago, Ill.).-At this particular time conditions existing in this, country, and elsewhere, make all questions of milling or smelting or mining, or anything else, absolutely secondary to the one question of labor. We have always devoted our attention largely to the efficiency of machinery, and to reductions in costs, etc., and have let this tremendous problem of our relation to labor more or less take its own chances. There has never been a time when those who are responsible for the operation of business of different kinds were as com-pletely at a loss as they are now, so that anything that can be brought out that relates to labor is, to my mind, of utmost importance. T. T. READ, Washington, D. C.-This formulation of a method of curtailing forces at the Copper Queen is a notable step in advance of our treatment of personnel in the mining industry. So far as I know, it is the

Jan 12, 1919

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

Jan 1, 1894

By J. Burns Read, Charles H. Fulton

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920