Search Documents

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By Francis T. Christy

One aspect of ocean mining that is frequently overlooked in discussions is the problem of establishing some form of legal control over the seas. Much of the discussion centers on mining in territorial waters, which are controlled by the various countries according to the Geneva Convention on the Continental Shelf, and perhaps by political subdivisions of countries such as the individual states of the U.S. But as technology improves and the mining of deeper waters becomes feasible, the problem of rights outside the continental shelf and territorial waters becomes a significant factor for anyone expending the time and capital for development. Several schemes are possible for regulating ocean mining but as yet none have been instituted, except what might be termed the "wait and see" approach. Even some of the coastal states in the U.S. have no regulations governing mining in the territorial waters under their jurisdiction. Until some regulation is formulated, there may well be little development in ocean mining due to the high risk of capital involved, both with respect to companies wishing to invest their own funds and financial institutions funding a venture to develop offshore mineral deposits.

Jan 7, 1968

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By Paul E. Dorr, Kenneth P. Pavlich

This paper covers the practical aspects of economic analysis of mineral ventures and the application of a publicly available computer program. The paper touches briefly on the time value of money concepts and the phases of project evaluation. The most comprehensive port ion of the paper deal s with the requirements for economic evaluation, including capital expenditure categories, operating expenses, required geological and engineering data, and tax considerations. Highlights of the 1981 and 1982 tax laws are covered. A case study using the MINECO computer program will be used to illustrate the economic evaluation concepts developed. Guidelines and goals of sensitivity analysis and Monte Carlo simulation will be discussed and demonstrated on the MINECO example. The MINECO software system will be displayed as an example of a "user-friendly", interactive, and flexible computer tool available to the mining professional today.

Jan 1, 1983

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neu-mann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempts to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2. was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form 12111. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

Jan 1, 1928

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee ' These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements' outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.' It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker' found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence' conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By G. Sachs

THE iron-rich iron-nickel alloys have at-tracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are Atomic per cent nickel FIG. I. FIG. 2. FIG, I.-HONDA'S AND MERICA's IRON-NICKEL DIAGRAM, FIG. 2.-MARSH'S IRON-NICKEL CONSTITU-TIONAL DIAGRAM. the base of many alloys with various out-standing properties. The iron-nickel alloys, therefore, have been investigated exten-sively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,1 and will be discussed in some detail in the sec-tions of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis,2 which is not dependent upon

Jan 1, 1940

By J. Parke Channing

These days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," " safety," '(industrial education," " efficiency," and the many other things which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the human and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved—not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them. How can it be done? For seven years a movement has been making

Jan 1, 1915

By C. A. Czako

INTRODUCTION In recent decades sintering and pelletizing of finely divided materials have become the primary tonnage producing modes of agglomeration. This statement is especially true in the iron and steel industry and, to a lesser degree, in the nonferrous, chemical and non-metallic minerals processing industries. In every industry the main objectives in agglomerating fines are essentially the same, namely to convert ores, minerals and chemicals of undesirable fineness into agglomerates characterized by a size consistency desirable for subsequent use or processing. Depending on the type of agglomeration process selected and the conditions maintained during agglomeration, the physical process of increasing size is complemented by a number of other unit processes. These processes can occur simultaneously, consecutively or in an overlapping manner. Some of these additional unit processes are incidental to the agglomeration operation, but at the same time can be critical, depending upon the subsequent use of the product. Accordingly, during processing, conditions have to be controlled to either suppress or enhance the extent of completion of these unit processes. The purpose of this report is to review laboratory testing as the basis for engineering modern sintering and pelletizing plants. Considering that most typical applications are for the iron and steel industry, agglomeration of ferrous materials is reviewed and discussed. When these total processes are adapted to suit non- ferrous materials, chemicals, or non-metallic substances, the over- all approach remains the same; only the processing parameters are affected as necessitated by the different nature of the materials.

Jan 1, 1977

By B. M. Larsen

Jan 1, 1965

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

Jan 1, 1916

Jan 1, 1898

By J. A. Jr. Church

I. EARLY FURNACES. COPPER blast-furnace construction in America has long recognized a general standard in the rectangular mater jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few mouths by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962