Search Documents

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Donald H. McLaughlin

MINERAL industry activities have not been seriously hampered by a lack of men with higher training. The balance between opportunities for employment and advancement and available personnel has been a happy one, with enough competition to stimulate effort but not the unfortunate conditions arising from an overabundance. of employment seekers. Nearly all mineral industry educational institutions have been concerned about the falling enrollment in mining and metallurgical courses of study during the past decade. But industry has drawn upon a supply of many types of technically trained men apart from those who prepared their careers specifically in the mineral industry. Some schools have made this possible by uniting geologists, mineralogists, and others with students in mining and engineering. On the other hand, some schools have combined their department of mining engineering with an over-all engineering department and continue to send their graduates into the mineral industry by another route. On the whole, this seems to be a good trend and is likely to result in men better trained for current problems than would have been possible under the older rigid curricula.

Jan 1, 1947

By G. Das, S. V. Radcliffe

The substructural features developed in tungsten as a function of annealing temperature (up to 2200°C) and type of material [undoped and doped powder metallurgy (PM) tungsten and electron beam melted tungsten] have been investigated by transmission electron microscopy. For doped PM tungsten wires, characteristic "par-ticulate" substructural features developed rapidly with increase in annealing temperature above 700°C. The features consisted of parallel rows of elongated or circular shapes (500 to 1000A diam) lying along the direction of the wire axis and were identified as internal voids by diffraction contrast experiments. In recrystallized doped PM rod, larger voids were observed and were identified by precision dark field analysis to be cubic in shape and bounded by (100) planes. In marked contrast with both the doped PM materials, recrystallized undoped PM rod exhibited only very occasional and randomly arranged voids. Furthermore, no voids were observed in either material after electron beam melting. The high concentration of voids in the doped PM materials is attributed primarily to vaporization of doping additions or their pvoducts situated at the original grain boundaries , whereas the few voids in undoped material are considered to be traces of microporosity which were not eliminated during sintering. A tentative mechanism is suggested for the dezlelopment of the voids in relation to the processing sequences (sintering and working) and to the subsequent annealing. In recent years, a characteristic substructural feature consisting of rows of small elongated or circular regions of light contrast lying along the direction of working has been seen in thin foil electron microscopy studies of annealed sheet, wire, and rod tungsten. These features were present in the published micrographs of sheet by Weissmann et al.1 and of wire by Meieran and Thomas2, although the authors did not draw attention to them. Wronski and Fourdeux3 observed similar features in sintered rod tungsten (it was not specified whether or not the material was doped*) and interpreted them on the basis of their ap- particles, based on extraction replica evidence from the fracture surface of the initial hot-rolled slab material from which the sheet was prepared. No diffraction contrast experiments on the features were reported in any of these studies. The present investigation was undertaken with the primary objectives of: a) identifying the nature of these substructural features in tungsten by electron diffraction contrast experiments, since the contrast for voids can be expected to differ from that for crystalline or glassy particles, and b) elucidating the origin of the features and their development. For the latter purpose, doped and undoped powder metallurgy tungsten was obtained as rod and wire to represent different stages of reduction during final processing. These materials were examined both in the as-processed condition and after annealing to successively higher temperatures. In addition, the same doped and undoped materials were examined after vacuum melting in rod form. I) MATERIALS AND PROCEDURE Doped powder metallurgy (PM) tungsten wire (commercial purity 99.9 pct W) was obtained in the as-drawn and surface ground condition (0.030 in. diam "ground seal rod"). Doped and undoped tungsten rod (0.075 in. diam) representing an earlier stage of final processing was obtained from the same commercial source (Refractory Metals Division, General Electric Co.). Lengths of both the doped and undoped rod materials were single-pass melted in an electron-beam zone refiner to examine the effect of vacuum melting on the substructure. Annealing was carried out in a tungsten crucible in a tantalum strip resistance furnace under a vacuum of l0-15 mm Hg. Longitudinal sections of the wire and rod materials were examined by light and electron microscopy. The preparation of thin foils suitable for electron transmission from 0.030 in. diam tungsten wire and the rod specimens was carried out by means of a high-precision microjet technique developed to provide lack of jet stability and precise control of the area thinned. The method is described in detail elsewhere.' The foils were examined in a JEM 6A electron microscope using a goniometer stage (±20 deg tilt, 360 deg rotation) and operated at 100 kV. To minimize contamination problems a 200 µ condenser aperture was used in conjunction with a useful beam current of 50 µA. II) RESULTS AND DISCUSSION A) Diffraction Contrast Analysis. In order to determine the optimum conditions for the development of the substructural feature, a series of isochronal 30 min annealing experiments were carried out on specimens of the doped PM tungsten wire. The transmission electron microscopy analysis showed that the as-drawn wire, Fig. 1(a), consists of 'fibers' whose long axis is closely parallel to the wire axis of (110). The fiber width averages some 0.5 µ. Dense disloca-

Jan 1, 1969

By R. G. Lazzell

THE British are worried about the postwar possibilities of their coal mining industry. Indeed, there are causes for this worry, with the aver- age 1943 cost of production at about $5.40 per long ton, compared to $3.20 in 1938. Average production per man day has dropped from 1.12 in 1938 to 1.03 long tons in 1943. As a comparison, production per man day in the United States is approximately 5 long tons. The average day wage in the British mines is now a little aver $4; in 1938 the average day wage was about $2.25. Great Britain produced 227 million long tons in 1938 from their deep mines, and in 1943 production was 194.5 million, with an additional 4.5 million from strip mines. To meet present wartime needs, output is being supplemented by the production of strip- mined coal, an industry that did not exist prior to the war. Strip mining is now producing at the rate of 15 million long tons per year.

Jan 1, 1944

By John W. Lane, Richard A. Ronzio, Frederick N. Bender

Climax Molybdenum Co. operated a hydrometallurgical plant at Climax, Colo., from August 1966 to August 1968 to recover molybdenum from an oxidized ore. The feed, tailings from sulfide flotation, was first upgraded by cycloning. The concentration plant handled 6000 tpd of feed and produced 2000 tpd of slime concentrate. The concentrate was leached by a sulfuric-sulfurous acid solution at 65°C. The molybdenum was solubilized in the form of "molybdenum blue." Activated charcoal was added to the leach tailings in a resin-in-pulp type circuit. Molybdenum was adsorbed on the charcoal. The charcoal was screened from the pulp and washed. The washed charcoal was pumped to columns where it was ammoniated and air-blown. The oxidized molybdate then was washed from the charcoal. The eluate was evaporated until ammonium dimolybdate crystallized out. The ammonium dimolybdate was calcined to molybdenum trioxide.

Jan 1, 1973

By Theodore W. Robinson

WHEREVER the amount of work renders it practicable the plan of using permanent standard solutions, in connection with the colorimetric carbon test, affords such manifold advantages that it is to be strongly recommended. That it has not attained a wider and more general application, is mainly due to the fact that, as the method is generally employed, the difficulty attending the production of the colors, and their doubtful stability when produced, have been only too evident to those who have undertaken their composition. The old method of using standard solutions made from sugar, coffee, etc., has always been hampered by the tendency of the colors to change upon exposure to the light, and the consequent liability to serious error, unless they are closely watched. Appreciating these difficulties, while recognizing the desirability of permanent colors, Mr. Magnus Troilius, at the suggestion of Prof. F. L. Erkmann, investigated the properties of cobalt, copper and ferric chlorides, with the view of determining their efficacy in the production of standard solutions. His results, as obtained, seem to have been satisfactory, but his treatment failed to eliminate many of the objections that have rendered the use of organic colors undesirable. The

Jan 1, 1888

By Robert Forsyth

IN working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remark- able when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense

Jan 1, 1876

By John W. Padan, John E. Crawford

Beginning with a small but positive participation in undersea mining, the Bureau of Mines continues its active investigations into this potentially tremendous field. The Bureau began its active role in undersea mining in September 1963, with a small task force of three dedicated scientists and a secretary, establishing headquarters at the old Tiburon Naval Net Depot about seven miles up the coast from San Francisco. The past months have been both busy and productive. With 22 Federal agencies involved in oceanography, it logically was the intent of Congress that the Bureau of Mines undertake research concerned only with the technology of marine mineral production and utilization. The Bureau has maintained this purpose in its activities at Tiburon, for while institutes, universities, the Navy and other Government agencies have developed exceptional programs in the fundamental science of the oceans, commonly called oceanographic research, little has been done toward advancing man's ability to exploit the ocean floors other than by drilling for oil and gas and sulfur.

Jan 3, 1965

By Edward Judd

THE old Cerro de Pasco smelter at La Fundicion, near Tinahuarea, 9 miles. from the Cerro de Pasco. mines and at an elevation of 14,300 ft., has now been replaced by a thoroughly modern smelting plant at Oroya, the junction point of the company's private railroad with the Central Railway, of Peru. This site has the advantages of being closer to the Morochoca mines, as well as nearer to the port of Callao, and at the same time is 2000 ft. lower in elevation, which benefits not only the cost of transportation but also the tech-nical operation of blast furnaces , and converters. The Oroya smelter was designed with the idea of .smelting about 2500 tons of. ore per day, but having in mind the possibility of increasing its capacity, all departments of the plant can be extended within reasonable -limits; for instance, if it is found that reverber-atory smelting is cheapest, taking into consideration the cost of fine crushing and fuel, it is possible to extend the roaster and reverberatory plants accordingly. The ore handling system is modern, consisting of belt conveyors, reclaiming machines, and electrically driven calcine cars, all requiring the minimum of labor. Waste heat from the reverberatory furnaces is utilized in boilers for the production of power to operate the plant, and the power house is equipped with condensing units to obtain the highest economy. Shop installations for the making of all repairs required for the smelter are unusually complete, includ-ing iron foundry, steel foundry, forging and machine shops, carpenter and pattern shops, and an electrical shop. There is also a plant for the production of all clay and silica refractory brick used in the furnaces; this is situated on the smelter site and is conveniently arranged for receiving raw materials and delivering finished brick to the several departments of the smelter. The laboratory is in a wing. of the general office, which is a two-story brick structure, situated on the smel-ter site.

Jan 10, 1923

By Robert Sisselman

Dramatic changes have been effected since 1955 in the mode of iron ore shipments within the U.S. In 1955, less than one percent of ore consumed in domestic blast furnaces-approximately 125 million long tons-consisted of pellets. Five years later, in 1960, some 94.8 million tons of ore were consumed, 14% in the form of pellets. Projections for 1980 reinforce confidence in this most economic of blast furnace feeds, and set U.S. pellet consumption at 151.2 million tons. In the last decade, pellets caught fire in other countries. By 1969, world production reached 96 million tons. This compares strikingly with present world output of 154 million tons.

Jan 9, 1973

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By Ralph K. Foster

During five underground mine fires which occurred in Arizona during 1980 and 1981, sealing the fire area became necessary. To minimize leakage into the fire area, ventilation control measures were instituted to balance pressure across the bulkheads. Problems en- countered in sealing the fire areas and measures taken to improve these conditions are discussed. The routing of the ventilation and ventilation control to en- sure the workers' safety were also important considerations in reopening the mines. The use of continuous CO monitors is discussed. One important consideration was the condition of the fire, and chromatographic analysis was used to establish this. Graphs comparing the Trickett ratio, carbon monoxide, carbon dioxide, and oxygen concentrations are given. The Trickett ratio was useful but needed to be augmented by the comparison of CO, C02, and 02. Problems with getting good samples from sealed areas and recommended procedures that were developed during these fires are discussed.

Jan 1, 1982

By Frank T. Sisco

DURING the past year the iron and steel industry of the world as a whole operated on a satisfactory basis. No discoveries nor new processes of outstanding importance were announced either here or abroad, although rumors of such were persistent. In general, the efforts of operating and research men in the iron and steel industry seemed to be confined to improving quality and reducing cost, not a new aim, for the same efforts have been noted in nearly all of the annual reviews of the industry for at least fifty years. Most published papers on blast furnace or steel-making practice were of minor importance, at least when judged by the criterion of radical change in process or product. If the number of reports in the technical journals, or articles in the trade press, is used as a basis for comparison, continuous-mill sheet is still the most important single product of the industry; papers were published detailing the results of the investigation of various phases of the

Jan 1, 1938

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By ERLE VICTOR DAVELER

ERLE VICTOR DAVELER, who in his application for membership in the Institute in 1909 modestly described himself as "millman," was born at Denver in 1885 and graduated from the University of California in 1907. After a few months' work at gold mills in California he went to Tonopah, where for the next two years he had a varied experience working on pumps, convey- ors, tube-mills and filters. For the following two years he was experimental foreman and metallurgical engineer for the Utah Copper Co. at Garfield. He was sent in 1911 to be assistant superintendent of mills at the Ray. From 1913 to 1917 he was mill superintendent at the striking but unsuccessful experiment in large-scale low-grade gold mining of the Alaska Gold Mines Co.

Jan 1, 1929

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By Basil Prescott

A thorough knowledge of the peculiarities of this type of orebody is necessary in sampling these limestone replacement deposits. Oxidized ores are often overestimated because of error in determining specific gravity and actual cross-section of the orebody, and sulfide ores are often underestimated because it is difficult to scatter the samples so that they will accurately represent the area under consideration. This paper describes various methods of sampling and cites factors that enter into the estimation of these deposits. IN THE science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each successful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation.

Jan 3, 1924

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956