Search Documents

By A. Weiss, W. A. Coster

The search for ore is characterized by a great variety of uncertainties, each of which can be resolved by obtaining information at a cost. Three exploration stages may be distinguished in which information can be obtained, based on inherently different cost structure: 1) the reconnaissance or scanning stage, 2) the examination or screening stage and 3) the project stage. This exploration sequence would roughly coincide with replies to questions as to: where, how, why and how much. As complete information in each stage is too costly to acquire, we must assess the probability that adequate information will be furnished by a limited amount of effort and attempt to maximize the expected value of ore to be found for a given exploration expenditure. Several problems are discussed relative to the mathematical formulation and possible computer procedures for determining the optimum allocation of a total exploration effort. Based on the available literature possible solutions to this problem are indicated. When scanning through published literature on mineral exploration, it seems at first that there is little room for substantial and systematic improvements in the efficiency with which the problem of discovery of new ore deposits is presently being handled by large organizations active in exploration. It appears equally difficult to offer something relevantly new which could generate a break-through in exploration thinking and cause a marked improvement in the ratio of successful undertakings to the total exploration projects started. On the other hand, a number of experts in recent years have urged that the problems in prospecting be analyzed in a more skillful and sophisticated manner than in the past. Their thesis is based mainly on the premise that the cost of finding mineral deposits will increase with increasing technical difficulties. In present large-scale exploration ventures, especially in those regions where outcrops and immediately visible geologic evidence are scarce, older methods of prospecting are increasingly being replaced by more indirect and systematic geophysical and geochemical methods with more emphasis on correct statistical design of exploration patterns. It is perhaps the oil industry which has made the greatest strides in developing statistically, well justified patterns in its search for oil; possibly because oil seepages, as indicators of the presence of oil, left off at an earlier point in time than did outcrops as indicators of base metals. Among the pioneers in the field of statistics and operations research, as applied to mineral exploration, the excellent works of Allais, Slichter, Koop-man, Mickey, de Guhnin, Krumbein, Griffith, Sichel, Krige, de Wijs, and Matheron may be mentioned. It should, however, be pointed out that three subjects of basic importance to the allocation of exploration efforts have so far received only scant attention in published literature, even by the aforementioned authors. In the first place, a more precise definition of the object of the search, i.e., a minimum-size orebody, seems to be outstanding. Secondly, a decision model is not a widely-discussed subject. Thirdly, no concentrated attempt so far seems to have been made to establish probabilities of the occurrence of economic deposits on a regional scale and to arrive at a slightly more accurate knowledge of the probability laws governing the deposition of ore. It is not the purpose of this paper to create new order in the complexity of uncertainties in which our decision processes in exploration necessarily have to be conducted. Rather, we intend to highlight some of the outstanding, hitherto unmapped territory, where diligent compilation and a utilization of present and historic data may statistically improve our chances of success. We hope that the contribution of this paper will lie in bringing allocation problems into better focus and in increasing the mineral industry's realization of the magnitude of the factors involved. THE MINIMUM-SIZE OREBODY The concept of target specifications for what constitute a minimum-size orebody in exploration is a rather variable one and depends to some extent on

Jan 1, 1963

By R. F. Ashton, D. S. Thompson

In reporting results of precipitation hardening experiments, it is customary to include such conditions as solution heat-treatment temperature, specimen size, and quench medium as well as the aging time and temperature. One portion of thermal history that is often overlooked is the effect of the heating rate employed to achieve the aging temperature. It is the intent of this note to demonstrate the importance of the rate of heating to aging temperatures. This work was carried out on the aluminum alloy 7075 aged at 162oC, a temperature commonly used to obtain stress corrosion resistant tempers. A 2 in. thick plate of 7075 was quenched into 24°C water after solution heat-treatment for 2 hr at 470°C. Approximately 13 in. around the periphery of the plate was discarded to minimize quench rate variations, and the remainder was divided into 0.5 by 1.8 by 2.0 in. blocks which were held at room temperature, 24oC, for 4 days. This aging, or incubation period, at room temperature allowed a copious supply of GP-zones to form. Blocks were then heated at various rates to 162oC using the practices shown in Table I. Both single- and two-step aging practices were employed for each heating rate. The single step consisted of heating directly to temperature at the indicated rate while the two-stage practice included an interruption of heating for 7 hr at 107°C. In the case of the two-stage 100°C per min heating rate experiment, the specimens were returned to room temperature after 7 hr at 107°C where they were held for 16 hr be-fore finally heating at this rate to 162°C. This devia-tion in practice is not considered to be significant. Blocks were removed after various times at 162oC, and aging curves were determined from duplicate R. F. ASHTON and D. S. THOMPSON,Member AIME, are Senior Scientists, Metallurgical Research Division, Reynolds Metals Company, Richmond. Va. Manuscript submitted December 2. 1968. IMD Table I. Aging Practices Two-step Single-Step Heating Rate* Aging Aging Heating Method oC per Min A B Programmed Air Oven 0.23 * 0.01 C D Programmed Air Oven 0.93 ? 0.03 E F Air Oven at Temp -10 G H Oil Bath at Temp ˜100 *Heating rate was measured with a thermocouple at the center of a specimen. An average value between the starting temperature and 3°C below the aging temperature is reported for practices E-H. PRACTICES 70 — A B C E and G 50 - 2 4 6 810 20 40 60 HRS.AT 162°C Fig. 1—The influence of processing variables on 7075 aging curves. Fig. 2—7075 aged according to practice H (single-step aged, fast heating rate) for 3 hr. Magnification 100,000 times.

Jan 1, 1970

By Walter P. Jenney

An investigation, conducted by the author, was begun in September, 1889, by the United States Geological Survey, having for its object the study of the questions bearing upon the occurrence and manner of formation of the deposits of lead- and zinc-ores in Missouri and the adjoining States. The field-work was completed in December, 1891. During the first season the State Geological Survey of Missouri furnished an assistant, and in other ways co-operated in the research within the boundaries of that State. In order that the ore-deposits of the southwest might be compared with those of other sections of the Mississippi valley, an examination was made of the lead- and zinc-mining area of Wisconsin-Iowa, and of the argentiferous lead-mines of the region extending westward from Hot Springs, Arkansas, to Indian Territory. In the discussion of the general geology, and in comparisons between the ore-deposits of the Mississippi valley and those of the Rocky Mountains, the writer has drawn largely from his personal experience, having been engaged for many years in professional work as a geologist and mining engineer in that region. The Director of the U. S. Geological Survey and the Scate Geologist of Missouri have kindly consented to the publication of the present paper. While giving the more important economic results, an endeavor has been made to set forth the unity of plan which appears in the formation of the deposits of lead and zinc of the Mississippi basin, and to show their relation to the argentiferous ores of the Rocky Mountains—that the ores of gold, silver, and mercury, and also of copper, antimony, zinc, and lead, have a universal common origin, irrespective of the geological formations in which they occur.

Jan 1, 1894

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

G. M. TAYLOR,* Colorado Springs, Co1o.-I do not think the plan outlined in this paper would work at Cripple Creek. Most of our men have had a pretty good education. The Cripple Creek district is a lessee district-I do not think there is one mine operating in Cripple Creek to-day that does not have the leasing system. We have as many men leasing on our property as we have mining and every plan who is working for wages is looking for n lease-everyman has mined for him- self, he has been his on7n boss on n lease, either on our own property or

Jan 1, 1919

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. Pat Doyle was born in 1849. At the age of fifteen he entered the Civil Engineering College of Madras, India, and left it at seventeen, having achieved special distinction in mathematics, chemistry,. and geology. Before be was eighteen years old he was in charge of two of the most important Sub-Divisions in the Madras Presidency, where he had ample opportunities for acquiring a preliminary knowledge of his profession, which was his chief object in joining the Public Works Department. In 1867, his energetic measures saved the island of Seringham from disastrous inundation. At this period he began contributing to the press ; and after a varied practical experience he came into public notice again in 1876, with an article in the Colliery Guardian on Indian Mines and Mining. In 1877 he became a Fellow of the Statistical Society of London. He was a founder of the Straits Branch of the Royal Asiatic Society and a life member of the parent Society of Great- Britain and- Ireland, as well as a member of the Independent Asiatic Society of Bengal. In 1878-9 he was Chief Superintendent of the Public Works of Perak; was active in having the Associate Member Class added to the Institution of Civil Engineers; and became a member of the Society of Engineers of London and of the North of England Institute of Mining and Mechanical Engineers. In 1880 he went to the Southern Colonies and held several appointments in Australia, where he became a member of the Johnsonian Club, Brisbane, and the Queensland Philo-

Jan 5, 1908

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By W. R. Hibbard

The increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform compatibly regardless of the single crystal crystallo-graphic strain mechanism, complicates this mechanism so as to increase the metal's resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: " Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of dcformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.zl Previous Investigations Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip werc reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elarn4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable yi in. from the boundary. Adcock,6 Yamaguchi,' Seumel, Hirstg and others have also reported this phenomenon as a qualitative trend. Yet attempts by O'Neill'o and Ljunggrenll to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface thc distribution of stresses was so altered

Jan 1, 1949

APRIL 10-Officially, spring comes to the Great Lakes on March 21 as it does elsewhere in the country but in the Superior district continued snow and freezing until late in March have caused citizens in Duluth to place their bets on April 15 for the first ore vessels if the ice breakup is left to Mother Nature. North and west of Duluth and near the eastern end of the Mesabilies the little town of Aurora, population 1100. As the little v-nosed snowplow, pride of the community, shuttled back and forth clearing Aurora's few sidewalks, the crowd in Bradich's Cafe were more interested in the impending high school state championship basketball tournament in Minneapolis than in the outcome of Erie Mining Company's petition for water rights for their proposed 10 million ton taconite concentrating plant. Such a plant would employ 4500 workmen, and at the prevailing ratio of 10 people for every mine worker in Minnesota, this would mean a 45,000 increase in population for Aurora and the vicinity in the next few years. Downstate fishermen are alarmed at the flurry of activity by the mining companies in pushing plans for large scale recovery of iron from taconite. Inconvenience to these gentlemen will be inconsequential when compared with the vast increase in payrolls for range communities. Oliver is pushing the construction of a fine ore agglomeration plant at Virginia which will give them valuable experience for projected taconite processing. Oglebay, Norton & Co. is ready to go at Beaver Bay, north of Duluth, as the right of way for a railroad from Babitt to Beaver Bay is secured as well as permission to dispose of tailing into Lake Superior at the site of the proposed concentrating plant. This company is also doing research in agglomeration at Ashland, Ky., in cooperation with other interests. The financing is yet to be worked out. Of the four possibilities for agglomerating taconite concentrate-sintering, pellitizing, nodulizing and briquetting-the prospects for pelletizing appear the most favorable., It seems likely that 60 cents per ton can be saved by this process over sintering because only 1 to 2 pct of coal is required as compared with 7 pct for sintering. One reason for the lower coal consumption is that the chemical transition of magnetite to hematite which transpires in the pelletizing process is exothermic.

Jan 5, 1950

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By B. DE MARE

THE No. 6 open-hearth furnace at the plant of the Worth Steel Co., Claymont, Del., is the first to be rebuilt according to the Kuehn system. This as well as the other five furnaces at Claymont, has a nominal capacity of 75 tons, but the actual charge is about 242,000 lb. No hot metal being available, the pig-iron is charged cold. Oil of low grade with an asphalt base is used as fuel. These two items have to be kept in mind when discussing the actual fuel consumption. Careful records have been kept covering a five weeks run and the following is a brief summary of them The time required to heat the furnace preparatory to charging from the time a wood fire was started until charging commenced was 36 hours. This, I understand, is much less than with furnaces of standard design. The draft of the furnace, as shown by a gage in the stack-flue, is 1.25 in. The maximum draft with new checkers on former runs was 1.50 in., this draft gradu¬ally decreasing as the checkers closed up. Both of the first helpers claim the present draft is all they need for the proper working of the furnace, and, as with the Kuehn regenerators the draft remains practically the same from beginning to end of a run, this is satisfactory.

Jan 1, 1929

By R. W. Rausch

BELT-CONVEYOR 'history in this country dates back to the end of the eighteenth century. Up to 1896 they were crude in design and application. The second era, dating from 1896 to about 1920, saw special study given to belt construction and idler design. The latter part of this era saw the beginning of the present-day antifriction idler. The third era followed World War I, when industry began to expand rapidly. Mines and quarries, steel mills, and power-generating plants became larger and greater quantities of ore, stone, and coal were being handled. It became vital that belts handle larger capacities, that they be longer, and that they be dependable for 24 hours per day. In this third era a radical change in belt conveyor design and application occurred. The design has became more scientific. Studies have been made to find out what factors influenced the power required for a belt conveyor and it was found that the sag of the belt between idlers and the flattening of the load between idlers had considerable effect on power requirements. So definite initial tension was put into the belt at the loading end and idler spacing was reduced at the foot end to limit this sag. Belt manufacturers made tougher and stronger belts.

Jan 1, 1947

NORTH AMERICA Number Members Alaska 36 Canada 323 Mexico 184 Newfoundland 3 United States Alabama 40 Arizona 111 Arkansas 8 California 646 Colorado 171 Connecticut 90 Delaware 21 District of Columbia 136 Florida 16 Georgia 7 Idaho 66 Illinois 208 Indiana 66 Iowa 11 Kansas 24 Kentucky 32

Jan 1, 1934

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By J. W. Schroeder

SEAMLESS pipe, the product produced from piercing a solid round billet of steel by the Mannesmann process, was first produced in the latter half of the 19th century, the Mannesmann machine having been patented in 1885. The products of other processes also have been termed seamless pipe; for example, the cylindrical section produced by "cupping," which consists of forming a cup from a flat plate or disk and further elongating the cup into a tube by passing it through a set of reducing dies. The purpose of this paper is to discuss some of the more important metallurgical factors and their relationship to the economical production of seamless pipe produced by the Mannesmann piercing process. The first seamless tube plant in America was established at Shelby, Ohio, in 1891, and was employed in the manufacture of bicycle tubing. For a number of years the bicycle industry was the only user of seamless tubing, and this tubing was produced by hot-rolling pierced billets imported from Europe and finishing on the cold drawbench. At the turn of the century, the automotive industry was responsible for an increase in the demand for seamless tubing. The growth of this industry was the dominant factor leading to the phenomenal growth of the petroleum industry, which in turn created a tremendous demand for seamless pipe. In addition; the old lapweld iron boiler tubes for stationary and locomotive boilers were replaced gradually by seamless tubes. Since 1929, the production of seamless steel pipe and tubes has increased over loo pct. In 1929, 1,459,9031 net tons of seamless pipe was produced, including both hot-finished and cold-drawn material, as compared with 3,087,3122 net [ ] tons in 1948. Table I gives the distribution of seamless pipe by classes for 1948. METALLURGICAL PROBLEMS From a metallurgical standpoint, the production of seamless pipe has presented many problems. Practically every type of steel, carbon and alloy, with the exception of the superalloys developed during World War II, has been pierced and rolled successfully into tubing. This includes bessemer, open hearth, by the stationary and duplex processes, and electric steels. The range of sizes produced is no less staggering to the imagination, when it is considered that the hypodermic needle, which is 0.016 in. diam with a wall thickness of 0.004 in., and pipe for gas or oil transmission lines, with a 26 in. OD, are both seamless tubes. Between these extremes, the range of diameters and wall thicknesses meets most present-day demands for seam-

Jan 1, 1951

By J. Rogers, K. L. Sutherland

THE relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. EXPERIMENTAL PROCEDURE The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testing18 have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.25 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948