Search Documents

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

Henry LOUIS, London, England (communication to the Secretary) : Prof. Richards's paper has impressed me as highly valuable. Without entering upon any discussion of it as careful and thorough as it deserves, I venture to mention one or two points which a perusal of it has recalled to my mind in connection with my own study and practice of ore-dressing. I always mentally divide jigging into two phases: 1. A particle at rest on the jig-bed is lifted and carried upwards by the rising current of water, at an increasing velocity, which tends to a maximum. When the upward current is stopped, the particle continues to rise with rapidly diminishing velocity until it comes to rest. This completes the first phase. 2. In the second phase, the particle falls from its position of rest with an increasing velocity which tends again to a maximum, and continues to fall until the rising current of water has reduced its velocity to zero. This completes the second phase. The second phase will evidently be greatly modified by the effect of suction, as Prof. Richards shows; but I do not see that his experiments very clearly imitate the action of the second phase. And the brief intervals at the end of each phase, when the mineral particle, by reason of its acquired velocity, is still moving, though in opposition to the water-current, yet remain to be investigated. I feel especially, in Prof. Richards's paper, a difficulty which I have felt with regard to all similar previous investigations, namely, that the experiments deal with particles falling a long distance, when the velocity becomes uniform. I question whether this uniform maximum velocity is attained in actual jigging-practice. If so, it is certainly for a comparatively very small proportion only of each stroke. It seems to me that an investigation like that of Prof. Richards, but confined to the first 6 or 8 inches of fall only, and carried out with suitably delicate recording-apparatus, is what we

Jan 1, 1895

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.'s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. However, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By Arthur Notman

SacRamento Hill is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the masa of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chal-cocite with associated carbonates as stringers in a mass of strongly brccciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or SO places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface obscrved in the other disseminated deposits of the Southwest.

Jan 1, 1916

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By M. C. Udy, P. C. Rosenthal

THE use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace, The present study presents the results of a systematic survey of. the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels, Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. EXPERIMENTAL WORK Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. [ ] Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions . was prepared with boron additions in amounts of 0.0015, 0.003, and o,006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two com¬mercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120, Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel scrap were used for melting stock. Deoxidation was carried out in the furnace with o.10 per cent aluminum. The aluminum addition was

Jan 1, 1946

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By Fuller, T. S.

THE number of rare or uncommon elements in use in the electrical industry nowadays is large, their application having come about through investigational work in industrial search laboratories and ' educational institutions. Such elements, together with those whose properties are more generally known, constitute Nature's gift to mankind and make possible the intricate devices which further our modern civilization. The' quality of raiaity is one of degree, and obviously depends largely on one's point of view. From the standpoint of quantity measured in the customary units of weight and volume, the amounts of many of the elements required are extremely small, but from the of view of performing some particular function or .other in a manner more satisfactory or cheaply than can be accomplished by any other sub- stance, the use in question may be extremely important.

Jan 1, 1928

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By S. J. Swainson

"It appears to me that the chief progress in milling operations in America have been made in the steady improvement of existing practice through both higher extractions and increased efficiencies of operations rather than by the development of new processes. The recent rapid development of sink-float, or heavy-medium separation, however, is an exception, and is becoming increasingly used to permit the economic treatment of certain low-grade ores that otherwise could not profitably be mined. The use of spirals and of small cyclones, both of which employ the principle of centrifugal force, show promise of increasing adoption through their application and efficiency in special cases." So did our distinguished colleague, O. A. E. Jackson, consulting metallurgist for the Union Corporation and president of the Chemical, Metallurgical and Mining Society of South Africa, summarize his impressions of a recent tour which he made of various metallurgical and milling plants in North America. I believe that all mineral dressers will agree with Dr. Jackson's concise conclusions.

Jan 1, 1950

By Orville R. Lyons

THE Russellton preparation plant of Republic Steel Corp., located north of Pittsburgh, Pa., prepares 3 1/2x0-in. Thick-Freeport coal by means of a 13-ft 6-in. diam Chance cone and 16 No. 7 Deister tables. The plant feed ranges between 370 and 410 tons per hr, of which approximately 31 pct is ¼x0-in. size, and the plant reject ranges between 14 and 16 pct of the feed. The 3½xY4-in. washed coal, the cone product, is dewatered and desanded by a double-deck Parrish-type shaking screen 46 ft long and 7 ft wide. The 1¼x¼-in. portion is further dewatered by two 4x12-ft single-deck vibrating screens. The ¼x0-in. washed coal from the tables is distributed to three 54x70 in. Bird centrifuges. The dewatered centrifuge product is combined with the product of the de-watering screens prior to loading into railroad cars. During the early part of 1951 complaints were received from officials at Republic's coke ovens concerning the moisture content of Russellton washed coal. The records revealed that during the first half of 1951 the shipped washed coal moisture averaged

Jan 1, 1954

H. H. Bleakney (Dept. of Mines and Technical Surveys, Ottawa, Canada)— The work of Dr. Machlin and his colleagues at Columbia University is so scholarly that one hesitates to take issue with them. Nevertheless the writer feels compelled to enter a demurrer to the mechanism of intercrystalline cracking proposed in this paper. The principal obstacle to its acceptance is found in its preoccupation with purely mechanical influences and its disregard for the chemical effect of impurities. The writer believes that the destruction of metallic cohesion by concentration of impurities at the grain boundaries is a necessary and sufficient condition for the development of intercrystalline cracking; and he believes that discussion of the numerous mechanical explanations proposed should wait until some valid objection to the chemical hypothesis has been advanced. It is nearly twenty years since Gillett" drew attention to the possibility that the chemical influence of precipitation might be the cause of intercrystalline cracking. As early as 1935, Greenwood'" remarked that grain-boundary precipitation of impurities in lead appeared to promote intercrystalline cracking. Again in 1939, Scott commented as follows on a paper by Thielemann and Parker:'" "There are at least two familiar phenomena that can influence grain-boundary cohesion: 1) intergranular oxidation; and 2) grain boundary precipitation. An important consideration in this work, therefore, is to determine which, if either, of these factors is responsible for the low values of cohesive strength observed." In 1952. the writer presented evidence," some original and some abstracted, which indicated that in copper, silver, aluminum, lead and iron, intergranular cohesion was a function of the purity of the metal. In 1954 Glen, discussing a paper by Ridley and Tapsell14 indicated his belief in a precipitation mechanism for the intercrystalline embrit-tlement of molybdenum steel and suggested that with an absolutely pure metal it would be almost impossible to obtain an intercrystalline crack. This suggestion has

Jan 1, 1959

By Charles Y. Clayton

THE general public does not know that there is such a thing as metallurgy and it is very seldom that you see the word metallurgy in print except in technical magazines. Perhaps it is more to the front now than in former years; the Dee. 30, 1929, issue of Time mentioned under the heading of "Science7' certain new achievements in metallurgy, which may be cited as a rare instance of the use of the word in anything but the technical press. Too often the part the metallurgist plays in the advancement of the different branches of engineering is overlooked. To say that the public does not know there is such a profession as metallurgical engineering seems to be a bold statement, but had there beep time a questionnaire could have proved this beyond doubt. Suppose a carefully-planned questionnaire had been sent to all high school students asking them, among other questions, to list the different branches of engineering, I believe that the several professions would have been listed in this manner: (1) Electrical engineering; (2) mechanical; (3) civil, and (4)' mining. One in each hundred might have listed metallurgy as an engineering profession. Even the Society for the Promotion of Engineering Education in its Bulletin No. 10-"Investigation of Engineering Education" lists Civil, Mining, Mechanical, Electrical, and Chemical, leaving out Metallurgical Engineering.

Jan 1, 1930

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

INTRODUCTION Conditions for formation of porphyry copper deposits appear to have been propitious in the Appalachian orogen from the end of Precambrian into Middle Ordovician, and again from Middle Devonian into Mississippian. In the Appalachians we can now record the evolution of a porphyry copper province within a developing orogen, one that reached metamorphic and structural maturity by the end of Devonian. Fig. 15, after Irwin and Coleman (1972), locates that portion of the Appalachian orogen included in this study, and Fig. 16 illustrates general geology of the area. Deposits mentioned in Table 3 and in the text are shown in Fig. 16. Data presented summarize personal observations by the author, published descriptions of specific areas noted in the bibliography, and abstracts from Provincial assessment files. Sources of previously published data are acknowledged. Few comprehensive descriptions of individual porphyry copper deposits in this area exist, so much of the data presented is new to the literature. Porphyry mineralization has, for this chapter, been restricted to porphyry copper de- posits, although porphyry molybdenum de- posits (Clark, 1972) are also shown in Fig. 16 (Hollister, et al., 1974). Copper- molybdenum and tungsten-molybdenum skarns are also omitted to simplify discu sion, though each is known in the area studied. Gaspe Copper is included, however; min- eralization in this deposit is present in the intrusion as well as in the skarn adjacent (Bell and Scott, 1954). Porphyry deposits listed in Table 3 are included because of some important feature, although other deposits have been reported (e.g., Kirkham and Soregaroli, 1975 ) . Clearly, no table now compiled could be complete. The pace of exploration insures that new occurrences will probably be found. Summaries of features exhibited by intrusions shown in Table 3 should remain valid, however, since they appear representative and are based on an adequate number of deposits in the area studied. Paleozoic porphyry copper prospects (shown in Fig. 16) are more common, apparently, in the northeastern part of the orogen, rarely having been found south of Catheart or west of the Logan Line. Occurrences of molybdenum and other associated lithophile elements are, however, known to the south and west as well as further north. Killeen and Newman (1965), King (1970),

Jan 1, 1978

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Robert S. Archer, L. W. Kempf

It is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a salt flux of which the active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification" and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Co. of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible value. It was necessary to learn how to control the modifying process

Jan 1, 1926