Search Documents

By D. H. Baldwin, R. E. Reed-Hill

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By W.M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By W. M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By Gardner F. Williams

These mines are situated in Griqualand West, which is now a part of the Cape Colony. The town of Kimberley is in latitude 28o40' South, longitude 25o10' East, about 640 miles northeast of Cape Town and 450 miles from Port Elizabeth on the east coast. It is connected with these towns by a railroad, which has been completed during the present year. The mines are located in a desert country, resembling the desert portion of Arizona. The elevation above sea-level is about 4000 feet. The climate is exceedingly hot during the summer months. Diamond Deposits.—There are four large diamond-bearing deposits at Kimberley, all lying within a radius of one and one-half miles, having the De Beers mine as the center. These are named the " Kimberley," " De Beers," " Du Toit's Pan," and " Bultfontein " mines. There is, also, directly west of the Kimberley mine, a small deposit, called " St. Augustiue," which has been prospected only, and

Jan 1, 1887

||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Science Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbott, A N , Mines Supt , Mazapel Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexico '23 Abbott, Clarence E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave, Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div 'Jenkins, Ky '15 Abbott, Robert R , Met Engr, Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 ?Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburgh, Kans '20 Abey, Hiroshi, Min & Met Engr, Takata & Co, 2 Yeirakucho, Nechome, Kojimachi-ku,

Jan 1, 1923

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.' It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this' paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By Colin G. ink

OUTSTANDI'NG in progress among the less familiar 'metals during 1936 is the electrolytic production of 99.9 per cent manganese meta1 readily and many quantity. Strictly speaking, manganese should not' be classed as 'a rare metal, since there is 800 times as much manganese in the earth's crust as there is zinc or lead. But manganese' as a metal is rare, just as titanium metal is rare though titanium is five times as abundant in the earth's crust as manganese.

Jan 1, 1937

By Henry D. Hibbard

A NOTED ordnance engineer once said to a friend, in speaking of the production of great steel guns, "How is it? We design our guns with a factor of safety of eight, and the guns burst." The vague way in which internal stresses and strains in iron and steel are often considered and spoken of makes it worth-while to examine them, as to their nature, their causes and results, how they may, for useful purposes, be advantageously dealt with, and how, when detrimental or dangerous, they may be reduced or kept within harmless proportions. Rankine defines ?strain " as a change of form or dimensions of a solid or liquid mass produced by a stress. This definition seems not intended to cover strains due to internal stresses, and it will help us in the present inquiry to consider strain as a tendency to change as well as an actual change of form. Internal strains in iron and steel are the result of stresses within the mass of the piece, some parts pulling and others pushing in resistance to them; or, in other words, some parts are in tension and some in compression, each part striving to relieve itself from strain and make the piece assume a form in which all parts are at rest. Subdivision, so that each part could relieve its strain by motion relative to the other parts, would, if carried out far enough, practically obliterate strain. The internal strains we are now to consider are not those due to the stresses of the service which the piece is rendering, either alone or as, a part of a structure, which may be termed service-strains, but those which originate or at least are contained in the piece itself. Internal stresses in a piece of metal are, like action and reaction, always equal and in opposite directions. The stresses

Sep 1, 1906

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be compared with field work. The same applies to geological contacts. Once these have been 3stablished at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By Guy Bjorge

IN recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No; 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B: & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and-Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Further-more, assurance of safety and uninterrupted operation required- two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent.

Jan 1, 1935

THE John Fritz Medal Board of Award, at its regu¬lar annual meeting Oct. 19, awarded its gold medal to Herbert Clark Hoover. Thus ended a process of selection begun a few years ago. The award was tentatively made a year ago by the Board, which is composed of sixteen recent past-presidents of the four national societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers, having together a membership of nearly 60,000. The sixteen members of the Board are: American Society of Civil Engineers : C. E. Grunsky, Robert Ridgway, George S. Davison and John F. Stevens ; American Institute of Mining and Metallurgical Engineers: William Kelly, J. V. W. Reynders, Samuel A. Taylor and E. DeGolyer; American Society of Mechanical Engineers: Fred R. Low, D. S. Jacobus, Dexter S. Kimball and Charles M. Schwab; American Institute of Electrical Engineers: Farley Osgood, M. I. Pupin, C. C. Chesney and Bancroft Gherardi.

Jan 1, 1928

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By AIME AIME

THE convention which met in Washington at the call of the Joint Conference Committee was called to order at ten o'clock on Thursday morning; June 3, by Richard L. Humphrey, temporary chairman, member of the American Society of Civil Engineers, who made a brief statement of the reason for the meeting. Lieut. Col. Charles W. Kutz, Corps of Engineers, U. S. A., and Engineer Commissioner of the District of Columbia, then welcomed .the engineers composing the convention on behalf of the District of Columbia and, the Washington engineers. Although an elaborate program had been prepared on which were many well-known speakers on interesting and important topics, , it was voted to intersperse this to fill in the usual and unavoidable hiatuses in the business program of such a convention[ Calvert Townley, president of the American Institute of Electrical Engineers, was elected permanent chairman, and J. C. Hoyt, of Washington, was elected secretary of the convention. The following committees were appointed: Consti¬tution and by-laws, Richard L. Humphrey, chairman; resolutions, Philip N. Moore, chairman; and program, F. H. Newell, chairman. Then, Gardner S. Williams, member of the, A. S. C. E. and the Grand Rapids Engineering Society of. Grand Rapids, Mich., and one-time member of the American Association of Engineers, offered the following resolutions:

Jan 1, 1920

By Holt, Grover J.

PRIOR to :1937 any discussion of mining and transportation in the iron mines of Minnesota would have been limited largely to conventional methods which have been used for years in the iron ore industry. Today, however, an inspection trip to the crest of almost any open pit on the ranges will re- veal great progress underground mining and the transportation of underground ore have also developed rapidly and if and when underground mining of iron ore again becomes generally economically feasible; these mining methods will probably witness a transformation equal to that which has taken place in the open pits.

Jan 1, 1941

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By Howard N. Eavenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few ears after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained. but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested. but without any illusions that it will be followed or that much attention will be paid to it.

Jan 1, 1946