Search Documents

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By R. S. Dean

BLUE HEAT PHENOMENA IN constructing a theory of the flow and hardening of metals, we necessarily make use of such phenomena as seem to be, universally observed in metals. It is, therefore, a matter of. concern to the constructors of such mnemonic systems if one or two of the group classified as metals show anomalous behavior. Such egregious phenomena are observed in pure or nearly-pure iron in the reaction of its mechanical properties to low-temperature annealing after cold work and to increased temperature of testing. In short it has been generally observed that iron," as an outstanding exception among metals, increases its hardness and strength by low-temperature annealing. after cold work,1 and also by increase of testing temperature to the range of 150° to 300° C. The investigation here recorded was made then with the object of ascertaining if similar phenomena were observed in high purity iron and, if not, to the presence of which impurities these phenomena could be traced.

Jan 1, 1929

By R. P. Alger, M. P. Tixier, D. R. Tanguy

In the combination induction-electrical log used at present in the field, the induction logging tool is appropriate for the investigation of moderately invaded formations. A new induction sonde with a radius and investigation about twice as large has been developed recently for the case of deep invasion. It has very nearly the same vertical resolution as the present sonde so that thin beds are defined as accurately as before. The characteristics of the new tool are described, the corresponding interpretation charts are given and field examples are discussed. The design of the sonic logging tool has been modified to improve the calibration and the reliability. The fact that porosity can be accurately recorded by means of the sonic log has prompted new interpretation procedures for saturation estimation, wherein the data concerning the various permeable beds in a given well are correlated. One approach consists of plotting transit time vs true resistivity, with an appropriate scale. With this approach, saturations can be estimated conveniently even in cases where formation water resistivity is not well known. In another approach, a comparison is made of the values of the formation waters computed from the re- sistivity and sonic logs. Using the concept of continuity, this procedure makes possible a quick determination of zones of saturation in shaly sands and/or in case of appreciable variations of formation salinities with depth. It has been found that the comparison of porosity from the sonic log with the apparent porosity computed from a short-investigation resistivity log may reveal, in many cases, the presence of residual oil and thus detect potentially productive formations; this procedure is valuable when the true formation resistivity and the resistivity of the formation water are in doubt. INTRODUCTION During the past year, the efficiency of log interpretation has been vastly improved. The improvements have largely resulted from the introduction of a deep-investigation induction device and from the application of new interpretation techniques that utilize sonic vs resistivity readings. Since the new interpretation techniques depend, in part, upon good values of true formation resistivity, the new induction log will be discussed under Part I. The sonic interpretation techniques will be studied under Part 11. Early in 1959, the 6FF40 induction equipment was introduced in the field. This device was designed for a better approach to true formation resistivities in deeply invaded zones. The greatly improved radial investigation of the 6FF40 equipment has been achieved without sacrificing vertical resolution. The first combination induction-electrical log, the 5FF40, was introduced as a standard tool in 1956 for the logging of wells drilled with fresh muds. The tool has received wide industry acceptance in the United States. 'The 5FF40 induction log has a radial investigation sufficient to overcome average depths of mud filtrate invasion. At 5d invasion, for example, the 5FF40 induction log will read about 1.4 R. in a water sand where R., = 10R,. At 10d invasion, such induction log would read 2.45 R. in the same water sand. In either case, the effects of invasion would not be sufficiently great to cause a water sand to be mistaken for a shale-free oil- or gas-producing zone. Some formations, however, invade deeply — in excess of 10d. Such water zones could be mistaken for oil-or gas-saturated sands unless the porosity balance' can clearly make the distinction. It is for these deeply invaded formations that the 6FF40 was developed. CHARACTERISTICS OF THE 6FF40 Radial Investigation Characteristics To describe the comparative responses of the 5FF40

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal-dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so that the terms which are defined in this chapter should be regarded mainly as working terms intended to facilitate communication. A coal slurry ' might be defined as a watery suspension carrying particles of fine coal and other assorted material ranging upward in size from the finest clay particles. Some particles may be in the colloidal sue range and exhibit characteristics of suspended colloids. The dilution of the system generally is such that it is in a condition of independent particle subsidence. In some coal mining areas a slurry is regarded as a suspension of fine coal and other materials having a dilution that cannot be economically dewatered by filtration. A coal slime may be regarded as a slurry containing particles of such size range that 50 per cent or more (by weight) will pass a 200-mesh sieve. Slime suspensions generally are difficult to handle without special treatment in conventional sedimentation equipment. A coal sludge is defined as a slurry that has been partly dewatered by sedimentation usually to a thick or viscous consistency where further dewatering can be most readily facilitated by filtration. Culm and silt are terms characteristic of coal-preparation practice which should be defined. In anthracite terminology, culm is the generally coarse residue or waste accumulation of coal, bone and rock from preparation plants most of which are no longer functional. Culm has a wide range of sizes, some rather coarse, and except to differentiate it from silt, the term is of limited interest in this discussion. In anthracite terminology, silt is the accumulation of waste fine coal, bone and slate settled out from preparation plant water in excavated basins. Silt is generally made up of particles ranging in size from 3/32-in. round-opening screen to the very finest sues. Silt is also referred to at times as sludge, fines, slush, and mud and is the partly dewatered derivative of what has been previously defined as slurry. In the terminology of the bituminous coal producing areas, the word culm commonly corresponds to slurry or slime, depending upon the size distribution of the suspended solids. Editor's Note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections authored by each individual as is the case in most chapters of this book.

Jan 1, 1968

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

By S. J. Burns, W. W. Webb

The dislocation arrangements formed during unsteady propagation of cleavage fractures on (010) planes in LiF have been investigated by high-resolution etch-pit techniques and by X-ray diffraction topogvaphy. In impurity-hardened crystals, cracks propagating in any direction on (010) planes at velocities of about 103 cm per sec are usually accompanied by light plastic deformation which is enhanced wherever the crack is allowed to hesitate. Dislocations with [011] type Burger's vectors are often formed looped around the crack tip. They are dragged along with the crack tips leaving edge dislocations lying nearly parallel with the clearage surface about 5µ from it. These dislocations are easily overlooked since they may initially intersect with the cleavage surface infrequently and later may disappear from the crystals due to image forces during aging at room temperature. Although the plastic work associated with these dislocations is only comparable with the reversible (010) surface energy, an instability in crack propagation appears due to a limit of the velocity with which dislocations can be dragged along with the crack. Transition to a fully brittle nonplastic fracture mode occurs when the crack velocity exceeds the velocity with which dislocations can be moved by the stress field of the crack. TRANSITIONS between brittle and ductile modes of fracture appear to be common processes in the behavior of materials in which the flow stress is close to the stress at which brittle cracks can propagate. High-strength engineering alloys fit into this category and the transition from ductile to brittle modes of crack propagation may be associated with catastrophic failures in these important materials. The methods of theoretical mechanics indicate the geometrical conditions in which these processes may occur but the detailed mechanisms controlling the generation of dislocations in the initiation of the plastic mode and the process by which the loss of plasticity occurs on transition to the brittle mode are not yet clear. Since these mechanisms are not amenable to direct observation in engineering alloys we have chosen a semi-ductile alkali halide LiF as a model system in which to observe transition mechanisms between plastic and brittle modes of crack propagation. Cleavage cracks in this system are known to undergo a plastic-elastic transition at velocities between 103 to 104 cm per secl and dislocation configurations in LiF are amenable to study by optical-microscopic observation of dislocation etch pits2 and by X-ray diffraction topography.3 We have been able to identify a dislocation mechanism responsible for the transition from brittle to slightly plastic modes of crack propagation in LiF. A model based on this mechanism permits calculation of the critical crack-propagation velocity for this transition and indicates the importance of the stress dependence of dislocation velocity in determining the critical crack velocity. Of course, this model cannot be carried directly over to more complex materials but it is quite possible that its qualitative features are generally applicable. Dislocations intersecting fresh cleavage surfaces in LiF were reported by Gilman,4 by Forty,5 and by Wash-burn et a1.6 Such dislocations were construed to have been nucleated where the cleavage crack hesitated or stopped, near stress concentrators, such as cleavage steps, on the crystal face. The loci of such dislocations deposited On the cleavage plane in bands were called "stop lines" or "deformation zones". Gilman, Knudsen, and walshl measured the velocity of cleavage cracks in lithium fluoride by evaporating thin resistive strips on the crystal side and recording

Jan 1, 1967

ALTHOUGH the refining period of the heat is generally defined A as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1964

By W. T. Lundy

THE forms in which sulphur is commonly found-native sulphur, sulphides of many metals and sulphates-are widely distributed throughout the world. The two first mentioned are the principal sources of sulphur. Substantial amounts of sulphur in some form are recovered from gases from industrial plants and from gases from smelters treating other minerals. In recent years, plants have been installed in the United States to recover sulphur in elemental form from sour gases."' The amount of sulphur so produced is small at the present time but undoubtedly will increase in the future. The recovery of sulphur from gases is not covered in this chapter, which is confined to: (1) native sulphur deposits of Texas and Louisiana; (2) those of Italy; (3) other scattered deposits of native sulphur; and (4) pyrites deposits found in many countries of the world.30 Sulphur, a nonmetallic element, occurs normally in well developed bipyramidal or tabular crystals of the orthorhombic system, as well as in stalactitic and earthy masses. The mineral has a distinctive yellow color, which may be dark and discolored by impurities; the streak is white; the luster is resinous; and the fracture is conchoidal to uneven. Sulphur is translucent to opaque; has a hardness of 1.5 to 2.5, a specific gravity of 2.05, and an atomic weight of 32.06.16 The molecular weight of the solid is expressed by the symbol SS and that of the liquid and vapor ranges from S2 to S8, depending on the temperature. Sulphur melts at a temperature between 2340 and 248°F, depending on its crystalline state, to a liquid of dark amber color, the boiling point of which is 832°F. The viscosity near the melting point is about that of water and increases to 50,000 times that of water at a temperature of 380°F, subsequently falling rapidly to a low figure at the boiling point. Crystallization changes slowly from rhombic to monoclinic above 205 °F and in cooling the transformation is reversed. The mineral is a very poor conductor of heat and electricity; it is insoluble in water and nearly all acids and is soluble in cold carbon bisulphide and carbon tetrachloride. It ignites in air at a temperature of 478°F, burning with a distinctive blue flame with evolution of sulphur dioxide.47

Jan 1, 1949

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932

By Eugene Stebinger

INTRODUCTION. A LARGE number of papers and reports dealing with the coalfields of Montana have been published + during the last 30 years, but the information is much scattered, appearing in many technical and scientific journals and in government reports, in many cases inaccessible to those most interested. In recent years, especially since 1905, ,our knowledge of the geology and coal contents of the important fields of the State has been much increased. Fairly specific and detailed information is. at hand on all of the principal coal-bearing areas. The fields for which data are not at hand are small and inaccessible, and their omission will not materially affect an estimate of the coal resources of the State, viewed as a whole. The paper here presented is a summary of existing information, all sources having been freely utilized in its preparation. The viewpoint adopted is that of the geologist, rather than that of the engineer or colliery operator, because by far the greater portion of the coal areas present have had only the most meager development, making information that, will aid in prospecting and opening the at present little used coal lands of paramount importance to those interested in the coal fields of the State.

Jan 9, 1913

By I. M. Roberts

THE war emergency has affected every phase of industry. The gas and coke-oven companies have sought faithfully to discharge their responsibility in this critical period and have willingly modified their operations where possible to meet the ever increasing demands made upon them. Our company made commitments for blast-furnace coke for war purposes which necessitated a reduction in coking time in order to produce the amount required to. meet the new demands. At the same time there were certain customers of long standing, who had been supplied with foundry and egg-sized coke produced on fairly long coking periods, who also were engaged in war work and whose patronage we desired to retain. Coke produced on short coking rates from the coal mixture we were then using would not have been satisfactory for these customers. The average width of our ovens is 19 ¾ in., which is a little wider than the more modern ovens of the present day. They were originally designed to give somewhat cool tops in order to produce a rich gas. This necessitates carrying the heats a little on the warm side so that the tops will be fully carbonized. A reduction in coking time, as is generally known, is accompanied by a reduction in the average size of the coke produced. This is due to the greater shrinkage that takes place at the higher temperatures required to carbonize the charges in a shorter time. The net result is that the coke is more cross fractured and longitudinally fractured and breaks up into small sizes on handling. The cokes produced from the better coking coals seem to be more susceptible to fracture at high temperatures than those from poorer coking coals. A coal mixture that produces a beautiful foundry-sized coke at 30 to 36 hr. may yield a product at 18 hr. that would be so badly fractured as to be unsatisfactory for foundry practice. COKING CHARACTERISTICS OF COALS Our problem was to find some economical innovation and develop a method that would enable us to reduce the coking time and still produce a coke satisfactory to our foundry trade. However, before discussing the results of our present operations, it might be well to present a few observations on the coking characteristics of coals in general. Most coke-oven operators carbonize a blended mixture of coals. It may consist of a single high-volatile coal with a single low-volatile coal, or of a combination of several high-volatile and low-volatile coals. Medium-volatile coals of the Eagle seam are used for the production of high-grade foundry coke. Medium and high-volatile coals are often blended with one or more low-volatile coals. The possibilities are almost infinite, but the combinations are limited by such factors as cost and facilities for handling multicoal mixtures, and by other practical considerations. Every coal has characteristics that make it blend better with a particular coal or coals in preference to others. This property has

Jan 1, 1944

By O. B. Ellis

Although thousands of tons of stainless steel have been used successfully for many types of equipment, there have been few cases of failures due to the phenomenon described as stress corrosion cracking. During the past seven years only six cases of such failures have been drawn to our attention and investigated in the Research Laboratories with which the author is associated. These failures oc¬curred in two coffee urns, two wool con¬ditioning units, one dyeing machine, and another in a part of a steam-jacketed stock pot. In each case the equipment failed in a comparatively short time after exposure to conditions of high humidity at tempera¬tures in the range of 100 to 200 F. The failures in all cases were characterized by general embrittlement and cracking of the stainless steel, with only slight indications of general corrosion except at the cracks. The first failure of this type was a coffee urn returned for investigation in 1937. The top and bottom sections showed a general corrosive attack and embrittlement and cracking of the stainless steel. The chemical analyses of these sections were as follows:

Jan 1, 1945

By C. H. Mathewson, Kent R. Van Horn

Copper and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.' It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962

By F. P. Dewey

The first systematic attempt of the National Museum to gather material representing the economic geology and metallurgy of the country was made in connection with the Centennial Exhibition. The department may be considered as having originated then, althongh it was not formally inaugurated until December, 1882. Previous to the Centennial, all the illustrations of economic geology had been included in the mineral collection, and the illustrations of metallurgy were so very few that they had also been included with the minerals. When the museum began its collections for the Centennial, the subject of the mineral resources of tile United States was placed in the hands of Professor Wm. P. Blake, who was eminently fitted to undertake the work by his experience at various international exhibitions and his extensive acquaintance with the mining industry of the country. Professor Blake prepared a broad and exhaustive plan for this purpose, and the very large collection shown at Philadelphia was well calculated to set forth the vast mineral wealth of the country. The history of the department proper may conveniently be divided into three periods : first, the formative period, during which the Centennial material was mainly administered upon, ending Jnly 1, 1884, with the beginning of the preparation for the New Orleans Exposition; second, the New Orleans Exposition period, from July 1, 1884, to June 30, 1887, during which the collections for the New Orleans Exposition were made, exhibited at New Orleans, returned to Washington, and installed permanently in the museum; third, the southwest-court period, from July 1, 1887, to October 1, 1889, during which the collections were arranged in the southwest court of the museum.

Jan 1, 1891

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By E. Houdremont, H. Schrader, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By H. Schrader, E. Houdremont, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By Michel T. Halbouty

The area for which oil and gas development is reported for 1938 in this paper is larger than that covered by the report for 1937, in that besides Duval, Jim Hogg, McMullen, Starr, Webb and Zapata Counties, comprising the Laredo district, this paper also includes the South Corpus Christi district, which is composed of the following counties: San Patricio, Nueces, Jim Wells, Kleberg, Kenedy, Brooks, Willacy, Hidalgo and Cameron, all heretofore included in A.I.M.E. Gulf Coast reports. In the map, Fig. 1, the area known as South Texas is represented by the counties south of the heavy black line. Production in the South Corpus Christi district, which covers an area that extends inland for 50 miles and follows the coast line, is primarily in zones ranging from the Catahoula, through the Frio sands, into the Vicksburg horizon. General exploration is done mainly with geophysics because in this district production is directly dependent upon structural conditions. In the Laredo district most of the production is from sand lenses; therefore, because these shallow sand lenses represent old shore lines which are monoclinic in character, the most satisfactory method of exploration in the Laredo district is drilling. This type of production centers around Duval County and follows a northeast-southwest trend along the Mirando district. Although drilling operations showed a decline from the preceding year, 1938 was highly successful as far as new discoveries and developments were concerned, and results of the year's operations should have an important effect on the near future trend of exploration and drilling. Besides the discovery of several new fields and many new sands in established fields, 1938 saw the discovery of a new Vicksburg sand trend and the first marine drilling off the South Texas Gulf Coast. Many new fields were discovered during the year, but only a few were subjected to an extensive drilling program. Several already established fields, especially in the Laredo district, received a large amount of drilling as new sands and extensions enlarged the producing areas, a

Jan 1, 1939

By Michel T. Halbouty

The area for which oil and gas development is reported for 1938 in this paper is larger than that covered by the report for 1937, in that besides Duval, Jim Hogg, McMullen, Starr, Webb and Zapata Counties, comprising the Laredo district, this paper also includes the South Corpus Christi district, which is composed of the following counties: San Patricio, Nueces, Jim Wells, Kleberg, Kenedy, Brooks, Willacy, Hidalgo and Cameron, all heretofore included in A.I.M.E. Gulf Coast reports. In the map, Fig. 1, the area known as South Texas is represented by the counties south of the heavy black line. Production in the South Corpus Christi district, which covers an area that extends inland for 50 miles and follows the coast line, is primarily in zones ranging from the Catahoula, through the Frio sands, into the Vicksburg horizon. General exploration is done mainly with geophysics because in this district production is directly dependent upon structural conditions. In the Laredo district most of the production is from sand lenses; therefore, because these shallow sand lenses represent old shore lines which are monoclinic in character, the most satisfactory method of exploration in the Laredo district is drilling. This type of production centers around Duval County and follows a northeast-southwest trend along the Mirando district. Although drilling operations showed a decline from the preceding year, 1938 was highly successful as far as new discoveries and developments were concerned, and results of the year's operations should have an important effect on the near future trend of exploration and drilling. Besides the discovery of several new fields and many new sands in established fields, 1938 saw the discovery of a new Vicksburg sand trend and the first marine drilling off the South Texas Gulf Coast. Many new fields were discovered during the year, but only a few were subjected to an extensive drilling program. Several already established fields, especially in the Laredo district, received a large amount of drilling as new sands and extensions enlarged the producing areas, a

Jan 1, 1939