Search Documents

By E. H. Bunce, E. C. Handwerk

The inherent difficulties of zinc smelting arise from the fact that metallic zinc is volatilized at the reducing temperature of zinc oxide and thus is liberated in the form of a vapor. This vapor must be subsequently condensed to obtain metallic zinc, first in molten and eventually in solid form. Zinc vapor is sensitive to oxidation not only by air but by combustion gases containing carbon dioxide. It is, therefore, necessary to carry out both the reduction and the condensation operations in a closed system consisting of an externally heated muffle with attached condenser from which extcrnal oxidizing agencies are excluded. However, the reoxidation of zinc vapor cannot be entirely prevented by excluding external sources of oxidation. Internal sources of oxidation are necessarily present when oxidic zinc ores are reduced by a carbonaceous reducing agent. The reduction reactions themselves involve, first, the production of carbon monoxide in an amount at least equal in volume to the zinc vapor produced in the reaction, and, second, the formation of carbon dioxide. Not all of the carbon dioxide is reduced again to carbon monoxide by the excess carbon in the time available, and the slightly oxidizing condition, which results, seriously affects the efficiency of the condensation of the zinc vapor to the metallic state. In the past the difficulties arising from these causes have limited practical zinc smelting on an industrial scale to the use of small retorts equipped with small condensers. The retorts had to be small, because a closed refractory container capable of excluding oxidizing gases from the heating chamber surrounding the retort could not be built in large dimensions. The size was also limited because ordinary refractories when thin enough to conduct heat readily are not capable of sustaining a heavy load of charge at high temperature. Moreover, a loose charge of zinc ore and carbonaceous reducing material such as fine anthracite coal or coke breeze is a poor conductor of heat, thus limiting the cross section of the retort. The operation of these small retorts requires arduous

Jan 1, 1937

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy's law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy's law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy's law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933

By D. C. Seidel, M. C. Fuerstenau, R. J. Roman

The role of surface charge in soluble salt flotation, which was developed in Part I, is extended to relate the theory to the specific phenomena of KCI-NaC1 separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed. The initial paper in this series developed and presented the hypothesis that one of the mechanisms of soluble salt flotation may involve electrical attraction between the collector and mineral surface. This hypothesis was developed from a combination of experimental data and free energy calculations, and details of the logic are presented in this first paper.* The studies have indicated that KC1 has a positive surface charge and NaCl a negative charge. KC1 can therefore be floated with sulfonate ion (RSO;) or with an aqueous polar species such as the aqueous amine chloride, RNH3C1(,,). The chloride end of the RNH3C1(,,) molecular dipole is probably negative and will be attracted to the positive surface of the KC1 particles and absorb (actually probably fit into a vacant chloride site) on the mineral surface. The amine end of the collector molecule would extend into the solution phase and provide the air avid surface required for flotation. NaCl particles are floated by such collectors as aqueous molecules of fatty acid salt, RCOONa(,,), in which the positive inorganic end of the dipole is attracted to the negatively charged surface of the NaCl and, in this case, adsorb and probably fit into a vacant sodium site on the surface. The aminium cation, RNH~, should also be a collector for NaC1. For certain collectors, actual precipitates of the collector must be formed before a sufficient amount of the polar aqueous molecule is present to effect flotation. In a system of this type there is a three-way equilibrium between: Aqeous Molecular Solid Precipitate - A of the Collector (Not Dissociated) . Ionic Species (Dissociated). The controlling equilibrium is probably between the precipitated form of the reagent and the aqueous

Jan 1, 1969

By Frederic L. Kadey

Perlite, as a volcanic glass, has been recognized since the Third Century, B.C. (Langford, 1978). The precise details of discovery often become lost in antiquity, and the variations among the stories pertaining to the more recent discovery of perlite as a material of commerce are no exception. Credit in the United States is given to a dentist who, while experimenting with tooth enamels about 1941, discovered that perlite-the rock-intumesced when subjected to heat. At about the same time it is reported that the chief geologist of Silver and Barytes Ores Mining Co. attempted to put out a picnic bonfire on the shores of Milos Island, Greece by throwing beach sand on it. The ensuing pyrotechnic display immediately conjured up in that man's mind the possibility of a new use for the volcanic rock that constituted most of the island. Very little was done with this discovery either here or abroad until after World War II. Today the name perlite is applied to both the hydrated volcanic glass, generally of rhyolitic composition, and to the lightweight aggregate that is produced from the expansion of the glass after it has been crushed and sized. Petrologically, it is defined as a glassy rhyolite that has a pearly luster and concentric, onionskin parting. Occurrences of perlite are restricted to several Tertiary to Quaternary age rhyolitic belts that trend in a generally north-south direction around the world. Commercially suitable deposits generally occur as domes of several hundred feet in height, although glassy zones in welded ash-flow tuffs and others associated with dikes and sills also have been reported. Mining is by ripping and blasting from open pits. Because of weight considerations, perlite usually is shipped to the local market area for subsequent expanding. In the United States, New Mexico leads in production with Arizona, California, Nevada, Idaho, and Colorado following in approximately that order. The principal use for expanded perlite is as a lightweight insulating aggregate in cryogenics, in plaster, concrete, and in loose fill insulation. Expanded perlite is also used in horticultural applications, and after subsequent milling and classification, as a filter aid. The United States is the world's largest producer and consumer of perlite. Table 1 shows the world production of perlite and Table 2 shows the perlite mined, processed, expanded, and sold or used by producers in the United States. Geology Composition and Morphology Any discussion of perlite must take into consideration its dual nomenclature, for it is known by the same name as both the naturally occurring rock and, after processing and expansion, as the lightweight aggregate of commercial significance. In its naturally occurring form, perlite is a rhyolitic glass that contains from 2 to 5% combined water. While perlite also can occur as andesitic or dacitic glass, these latter types are of negligible commercial significance. Table 3 lists the chemical composition of a few typical perlites (Anderson, et al., 1956; Langford, 1979). What sets perlite of commercial significance apart from other volcanic glasses is the fact that under the proper conditions of preparation-crushing and sizing-it will, when rapidly introduced into a flame of sufficient temperature, expand or "pop." All of the elements of composition contribute to the expansibility of the rock. The role of the combined water, however, is the most significant because it is believed not only to produce a fluxing effect in the softening of the highly siliceous glass prior to expansion, but it is also responsible for the explosive force of expansion through volatilization during heating. The current theory of the origin of the water in perlite is now less con-

Jan 1, 1983

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

Jan 8, 1951

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By W. M. Albrecht, M. W. Mallett

The solubilities of hydrogen in titanium and several of its alloys were determined at 600 to 1000°C and pressures of 0.05 to 10µ of mercury. Solubility increases with increasing beta phase in the alloys. Factors found to affect degassing rates are specimen size and presence of thick surficial oxide. Removal of hydrogen by heating in vacuum and in flowing inert atmospheres was studied. Practical curves predicting minimum degassing times are presented. THE presence of hydrogen in titanium and titanium alloys has detrimental effects on the mechanical properties of the metal.'"," The hydrogen content of commercial titanium is sometimes of the order of 200 ppm by weight' and varies with alloy composition. As a consequence, titanium and some titanium alloys as normally processed are sometimes not ductile unless treated to lower the hydrogen content. The best known hydrogen-removal treatment is heating the material in a vacuum. The rate of removal (degassing) at a give temperature determines the duration of the treatment required to attain a satisfactory low hydrogen level.

Jan 1, 1959

By K. I. Savage, S. C. Sun

This paper describes a process developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal and pyrite flotation which leaves the clays in the flotation pulp. A bituminous coal refuse containing 10% sulfur and 30% carbonaceous material was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material; and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocycloning) may be used to increase the pyrite : coal ratio in the flotation feed. Cost estimates for the process show a profit of $2.28 per ton of low pyrite grade refuse, but these do not include labor, maintenance, overhead and plant depreciation. The development of this process consisted of three parts: (1) exploratory tests, (2) op-timazation tests and (3) confirmatory tests. The objectionable qualities that sulfur imparts to coal have been commented upon from early times, and they have become more objectionable as the uses of coal have grown. In whatever form coal takes — raw, carbonized or gasified —the sulfur content remains objectionable, and therefore its compounds are removed as completely as possible. It has long been known that sulfur occurs in coal in different forms. In 1861, sulfur was said to exist in the state of sulfuric acid in combination with a base; in combination with iron as iron pyrites; as bisulfides of iron; and in combination with the organic elements of coal.' Pyritic sulfur is a term loosely used to cover the sulfur associated with iron in its various forms. The mineralogically recognized forms are pyrite (FeS2), pyrrhotite (Fe 1-x S) and marcasite (FeS2). The particle sizes of pyrites vary widely. Isolated grains of marcasite smaller than 15 microns have been found disseminated through coal.2 Hair-like "veins" of pyrite filling cracks in vitrain have been found. At the other extreme, lumps or nodules of pyrites large enough for removal by hand picking have been encountered. Organic sulfur, unlike pyritic sulfur, does not exist as discrete particles, but is instead intimately associated with the coal structure and thus it is impossible to remove it or reduce its concentration by physical or mechanical means.2 In the preparation of coal for its various markets, the pyrite minerals (pyrites) are separated from the raw coal feed. This separation process concentrates the pyrites in the tailings or other waste products. It would be desirable to recover these pyrites for three reasons: (1) Pyrites are potential sources of sulfur and iron. In 1967, for the fifth consecutive year, Free World consumption of sulfur exceeded production.3 Propelled by the shortage, the domestic price of sulfur has risen from $24 to $38 per long ton (bright). (2) The refuse, when placed in piles, becomes ignited. The pyrites (FeS2) bum, giving off SO,. Thus, the pyrites are a cause of air pollution. (3) Also, the pyrites undergo chemical reaction when exposed to air. The refuse is leached by waters which result in stream pollution due to the water-soluble iron and acidic reaction products. Coal refuse also contains coal minerals and clay minerals. Therefore, any process for recovering the pyrites must successfully separate them from the coal and clay minerals. In the study discussed here, ten different bituminous coal refuse samples were successfully upgraded in pyrite content. These samples represented a wide variety of coal waste materials from Pennsylvania and other states. The variabilities of the sulfur and coal contents are shown in Table I. The extremes are Sample J, a high sulfur-low coal, and Sample B, a low sulfur-high coal. Definitions of some of the symbols or terms used in this report are given below: Mesh size—Tyler standard mesh screen sieves with an opening based on the square root of two. Fe —Indicates iron, as determined by a stannous reduction-dichromatic oxidation method. S—Indicates sulfur, as determined by the ASTM "Eschka" method for sulfur in coal.

Jan 1, 1969

By A. M. Abouzeid, S. Chander, D. W. Fuerstenau

Today numerous ores contain valuable minerals in finely disseminated form; and although the recovery of these fine mineral particles is generally exceedingly difficult, diminishing raw material resources necessitates the recovery of such mineral values. In many systems, the efficiency of recovering fine particles is still extremely low and often fine particles must be discarded as slimes. However, in recent years, various advances have taken place in the recovery of mineral particles in the very fine size range. In this paper, the background and performance of a number of processes for fine particle processing and separation are reviewed and discussed, particularly from the point of view of how fine particle recovery might be improved.

Jan 1, 1979

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

ALABAMA Altoona -Cain, J Anniston-Cowie, L K Hermrod, A A White, H E Bessemer -Abbott, C E Ball, E M Mitchell, F R Thompson, N E Birmingham -Adler, J E Aldrich, T H Aldrich, T H, Jr Blackburn, A R Bush, M W Clark, G H Cowrn, P G Crane, W R Crawford, G G Crockard. F H

Jan 1, 1923

By Georg Masing

Jan 1, 1933

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

By C. E. Lawall

WHEN this study was started very little information was available, regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to properly classify West Virginia coals.

Jan 1, 1932

By Samuel L. Hoyt

The present report represents that part of the work that has been done by the War Minerals Investigation, Manganese Section, of the Bureau of Mines, on the use of manganese alloys in open-hearth practice. The magnitude of the work and the number of people participating in one way or another make it difficult to acknowledge adequately the services of all who have contributed to the success of the work. It would be amiss, however, to pass to the body of the report without mentioning the hearty cooperation and willingness to assist of the various manufacturing interests. With such a sympathetic attitude toward this investigation, our work was assured of success. Inasmuch as the unhappy circumstances that rendered this investigation necessary have now passed, this report is made in the hope that the results may prove of some permanent value to the peace-time operation of our open-hearth industry. Broadly speaking, the purpose of the manganese investigation was to consider the most suitable means of utilizing our domestic supply of manganese and thus relieve, to the maximum extent possible, our shipping of the burden of importing manganese ores. It was not held that any decided shortage of manganese was imminent but rather that every legitimate means should be utilized for making our ship tonnage available to European service. While we have considerable metallic manganese in this country, it occurs largely as a low-grade mixture with iron or silica or with both. The open-hearth investigations, therefore, were carried on to determine the extent to which domestic or low-grade alloys could properly be substituted for high-grade alloys without materially impairing the steel production as to either quality or quantity. Also, it was held that such an investigation would yield valuable results to the steel industry as well as contribute, in no small way, toward directing future investigations in the same field. To the practical steel manufacturer, especially to him who felt no immediate concern about

Jan 1, 1920

By W. M. Weigal

ECONOMIC deposits of barite occur in Missouri in two main districts. The most important, the Southeastern or Washington County district, is in the southeastern part of the state, mostly in Washington County with a small extension into the northeastern part of St. Francois County. Roughly, it embraces nine townships or about 200,000 acres and accounts for from 80 to 90 per cent. of the state production. The Central district, in the central part of the state, includes most of Morgan and Miller counties, and parts of Camden, Benton, Moniteau and Cole counties. The area embraced is much larger than the Washington County district, but the deposits are more infrequent. The location and general area covered by the two districts is shown in Fig. 1. There is another small area in southern Franklin County but so far its production has been of small consequence. It might be considered as a northward extension of the Washington County field. An area in the central part of Hickory County has also produced a small amount. The outline of the districts as shown indicates the general area in which deposits have been found. The total area covered by deposits of barite is only a small part of this, as, in the Central district especially, there may be miles of supposedly barren areas between ore-bearing areas of an acre or two in extent. The date when barite was first mined in Missouri cannot be definitely stated, but the industry probably dates back to about 1860. The occurrence of barite was known long before this, as it was encountered in the lead mines in Washington County and mentioned by several earlier writers.' Missouri is reported as producing 8000 tons in 1882 so it is evident the industry was well under way in the seventies in order to have arrived at this substantial production. By 1893 Missouri production had increased so that it ranked with that of Virginia, then the largest producer. It increased until in 1914 Missouri accounted for about 65 per cent. of the total United States output. Recent Production of Barite Table 1, compiled from Mineral Resources, published by the United States Geological Survey and Bureau of Mines, gives the production of

Jan 1, 1929

By J. Halpern, D. R. McKay

SOME of the most important hydrometallurgical developments in recent years relate to processes involving the oxidation of sulfide minerals in aque- ous suspension at elevated temperatures by air or oxygen under pressure. Among these is the acid pressure-leach process which has been developed, particularly for the treatment of pyritic uranium ores.1-5 In this process, an aqueous suspension of the ore is digested in an autoclave, in which an overpressure of air or oxygen is maintained, at temperatures above 100°C. Oxidation of the pyrite (FeS,)

Jan 1, 1959

By J. J. Jakosky

ALL electrical geophysical methods depend for their operation upon the effects produced by the flow of an electric current. By studying these effects it is possible to predict the general axis of current flow. The greater flow of current is in the path of greatest, effective conductivity; and since the effective conductivity of a mineralized zone is different from that of its surrounding envelope (usually much greater), it is possible to locate such a mineralized zone by the distribution of current. Due consideration must be given, of course, to geological structure, to type of mineralization, and to other factors. A number of methods are used to cause this flow of current, and various methods are available for detecting the presence of such current flow and for studying its effects. In a rather detailed way, this paper will discuss the theoretical and practical phases of the inductive methods of geophysical prospecting. ELECTROMAGNETIC GENERATION OF AN ELECTROMOTIVE FORCE The inductive method is so named because the current flowing in the conductor is obtained by electromagnetic induction, instead of by the use of ground electrodes through which a current is passed as in the applied potential systems, or by direct contact with the orebody. An alternating current flowing in a coil will create an electromagnetic field around the coil. This field will have the same frequency as the current and will radiate or travel outward from the coil in closed magnetic or flux circuits: These flux circuits (in air or a homogeneous medium) will be perpendicular to the plane of the coil and will extend or travel outward with uniform velocity in every direction. Maximum field exists in the plane of the coil. Such a coil used for transmitting or as the "energizer" will exhibit similar figure-eight characteristics to those exhibited by the direction-finding coil which will be described in detail later.

Jan 1, 1928