Search Documents

By R. E. Fryxell, E. C. Duderstadt, P. K. Conn

Permeation rates for nitrogen through are-cast tungsten were measured in the temperature range 1800° to 2600°C at nitrogen pressure differentials of 1.0 and 0.1 atm. Gas chromatography was used to measure the quantities of nitrogen which permeated through 0.26-and 0.53-mm-thick membranes. Permeation rates were proportional to the difference between the square roots of the nitrogen pressure on each side of the membrane and inversely proportional to membrane thickness, indicating that atomic nitrogen was the difjusing species and that diffusion was the rate-limiting step of the process. Permeation coefficients calculated from the rates may be represented by the equation: where P is expressed in the units cu cm (stP)-mm per 1/2 sq cm-min-atm"' and 70.0 * 0.8 is the activation energy in kcal per mole of permeating species. In a previous paper' permeation rates were reported for hydrogen and for oxygen through tungsten. The permeation cells used for the hydrogen measurements were suitable for measuring nitrogen permeation under similar conditions, so the study was extended to include nitrogen. Permeation rates of nitrogen through the polycrys-talline arc-cast tungsten membranes were measured in the temperature range 1800" to 2600°C using two membrane thicknesses and two nitrogen pressure differentials. Permeation coefficients were calculated and the activation energy of the process determined. THEORY For diatomic gases which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at an elevated temperature where bulk diffusion is the rate-limiting step of the process is given by the equation: where: q = total amount of gas permeating a membrane, P = temperature-dependent permeation coefficient, A = area of membrane, t = time, p1 = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, and d = thickness of membrane. When bulk diffusion is the rate-controlling step, and the solubility of the gas obeys Henry's law, a further relationship is that, for any given temperature and pressure, the permeation is the product of diffusivity and the amount in solution. The permeation coefficient, P, is temperature-dependent according to the equation: where: Po = permeation constant, Q = activation energy, R = gas constant, and T = absolute temperature. EXPERIMENTAL PROCEDURES Cell Design and Experimental Apparatus. Two of the permeation cells used for the previous measurements of hydrogen permeation are shown in Fig. 1. Each consisted of a cylindrical chamber divided into two parts by a permeation membrane fabricated from high-purity (>99.9 pct W) wrought tungsten sheet made from vacuum arc-cast tungsten. The membrane in one cell was 0.26 mm thick and the other was 0.53 mm. The fabrication of these cells was described previously.' The permeation cells were mounted vertically in a high-temperature tungsten resistance furnace and the membranes and the center portions heated to test temperatures. Temperatures were measured by sighting an optical pyrometer on the edge of the membrane through a small hole in a tungsten plate which was fastened to the side of the cell. This arrangement provided an approximate black-body condition and eliminated the need for emittance corrections. Appropriate corrections were made for the quartz window through which the temperatures were measured. Argon gas flowed through the 10-liter volume of the furnace at the rate of 4.7 liters per min. An impurity

Jan 1, 1969

Jan 1, 1962

By R. S. Goodrich, G. S. Ansell

The microstructure of three Al-Al2O3 SAP-Type alloys (containing 2.0, 3.0, and 5.7 wt pct alumina, respectively) was studied utilizing transmission electron microscopy. These alloys were fabricated from aluminum powders by powder-metallurgical techniques, cold-rolled into thin strips, and recrys -tallized. Thin foils suitable for an electron-transmission study were then prepared from the strip material by electropolishing. The microstructure of these alloys is shown to consist of small (0.1 mean diameter) plate -shaped alumina particles finely distributed in an aluminum matrix. In the higher-oxide content alloys the platelets are somewhat larger and more irregular in shape. The distribution of oxide particles is not uniform and there is an increasing tendency toward clumping SINCE the discovery by Irmann1 that aluminum alloys produced by compacting, hot pressing, and extruding fine aluminum powders possess remarkable high-temperature mechanical properties, the Al-A12O3 SAP-Type alloys have been utilized extensively as model dispersion-strengthened alloys in both experimental and theoretical invest igations.2-8 The use of the SAP-Type alloys as model dispersion-strengthened alloys implicitly assumes that their microstructure has been completely delineated. This is, however, not the case. with increasing oxide content. In all the alloys studied, the mean center-to-center spacing of particles was quite small (0.2 u) due to the very fine oxide debris present. Selected-area diffraction of the specimen identified the oxide as either y Al2O3 or y' Al2o3. The re crystallized MD-5100 alloy exhibited a mean grain diameter of only 0.7u, while the grain size of the other alloys was several hundred microns. Severe pinning of the grain boundaries by oxide particles was rarely observed, and the grain boundary triple points in the small-grained MD-5100 alloy were often particle -free. Diffraction contrasts visible around the particles are attributed to elastic strain fields set up by differential thermal contraction during cooling from the recrystallization anneal. Early investigation demonstrated that optical metallography did not possess sufficient resolution to observe the microstructure of the SAP-Type alloys.' Later, extensive use was made of replication techniques to study the microstructure by means of electron microscopy.7-9 These studies indicated that the SAP-Type alloys consist of a dispertion of irregular Al2O3 platelets, approximately 150A thick 9 and a micron or so on edge,9 distributed in a matrix of commercial-purity aluminum. These oxide platelets tend to be oriented in the aluminum matrix, with their largest dimension parallel to the extrusion direction. 8,9 A study employing polarized-light techniques1' indicated that the grain size of a series of as-extruded SAP-Type alloys was several microns in diameter, while the grain size after re-crystallization was several millimeters in diameter. A more recent study 12 utilizing surface-replication techniques examined the particle morphology,

Jan 1, 1964

APPROXIMATELY 26 percent of the total ore production to date from the largest single deposit of copper-bearing material in the world was mined during the war years, 1942 to 1945, at Chile Exporation Company's great open-pit mine at Chuquicamata, Chile. About 18 percent of the total waste removed during the life of the mine was handled in the same period. The total of ore and waste represents approximately 24 percent of the total material that has been excavated from the pit. This is more than was removed in the first fourteen years of operation from 1914 through 1927. The pit at Chuquicamata is 17/8 miles long, 1/2 mile wide, and has a present vertical extent of 817 ft between the top of the highest bench and the lowest bench being worked. However, when

Jan 1, 1948

By Edward C. Stephens, Robert R. Coats

High-grade copper ore was discovered in 1932 in the long-dormant Mountain City (Cope) mining district, Elko County, Nevada. From 1932 to 1947, the one producing mine in the district, the Mountain City Copper Mine, produced 1,109,878 short dry tons of ore averaging 9.745 per cent copper, 0.274 ounces of silver, and 0.0057 ounces of gold per ton. The Mountain City Copper Mine is developed in eugeosynclinal rocks of Ordovician age, the Valmy Formation, which is part of the upper plate of the Roberts Mountains thrust. On the Valmy were deposited unconformably first, a elastic formation of Devonian or Mississippian age, the Grossman Formation, succeeded unconformably by a ·sequence of three conformable formations, the Banner, the Nelson, and the Mountain City. The Banner Formation probably is early Late Mississippian in age; the ages of the Nelson and Mountain City are not known precisely but are believed to be of Late Mississippian and Carboniferous(?) age, respectively. A thick formation of elastic rocks, limestone, and volcanics, the Reservation Hill Formation, has been thrust over the Mountain City. The age of the Reservation Hill is unknown but is presumed to be Pennsylvanian(?) and Permian(?). Several plutons of Cretaceous quartz monzonite intrude the Paleozoic formations; they and the intruded formations have been laid bare by erosion, and several sequences of volcanic rocks of Miocene and Pliocene age, and perhaps in part older, have been successively deposited on irregular erosion surfaces. The primary mineralization of the Mountain City Copper Mine is believed to postdate the deposition of the Nelson Formation and to predate the intrusion of the quartz monzonite. The primary ore bodies are lenticular in shape and are composed largely of quartz, pyrite, and chalcopyrite. The ore lenses, in general, strike northwestward and dip northward. They occur in the Valmy Formation within a definite stratigraphic sequence composed largely of shales with associated minor quartzite lenses. The ore is epigenetic. The principal ore body, the "200," was completely leached to the 200 level. Abruptly beneath the barren gossan was supergene copper sulfide ore, much of which assayed 50 per cent copper. The secondary copper minerals are sooty and massive chalcocite, bornite, and covellite. The supergene enrichment of the ore may have required a large part of Tertiary time.

Jan 1, 1968

By George B. Langford

ON THE QUESTION of postwar controls there are today three schools of though ; some advocate state control of everything the socialists ; second are those who advocate the removal of all governmental control over industry - the freedom of enterprise ideal ; and third are those who advocate a middle course - sufficient control to stabilize economic and industrial life, and to prevent violent fluctuations such as we saw in the interwar years. I advocate this third course. I firmly believe un free enterprise, but not in freedom of enterprise, or laissez faire, and there is a great and significant difference between these two.

Jan 1, 1944

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By Blandford C. Burgess

Mica is an orchid among minerals. It is formed in pegmatites, one of the most bizarre of igneous formations, and is exceeded by few other minerals in the perfection it may attain as to size, color, and cleavage. First used for window glazing, as an ornament and article of trade, it has become one of the most essential insulators of electricity, heat, and shock. Most internal combustion engines use mica condensers or capacitors and such machines of war as planes, tanks, and submarines are immobile without it. The original manuscript of this guide was written in April 1943 at the peak of war emergency. It was not used because shortly thereafter a decision was made to buy on a one price basis eliminating differentials for both quality and size. This is now presented with the thought that from the standpoint of preparedness we can only consider another war imminent and every effort should be made to set up in usable form the experience gained during the Second Morld War. Colonial Mica Corp. was set up by Metals Reserve Co. as a wholly owned government agency to encourage production of domestic mica and to purchase it. It soon became the exclusive buyimg agency for such mica. The writer as Southern Manager called on all the private agencies buying mica to assist in formulating buying policies, methods, and prices. A meeting was held for that purpose in Asheville, N. C., July 20, 1942. In the general discussion the first two hours of the meeting it was decided that the following factors should be considered in pricing strategic mica: clearness, flatness, trimming, color, classification (size and quality), free splitting, hardness, and air inclusions. Most of the mica miners have been buying strategic mica, according to the mine, as No. 1, No. 2, or Nos. 1 and 2 combined. In addition to these grades of strategic mica they have been buying three lower grades of mica, electric (vegetable-stained), black-spotted and black-stained. A number of mines were named one by one and the buyers present gave their opinions as to the basis they would use in buying the sheet mica from each. It was suggested that in addition to the prices already published, prices be posted up to 10 pct higher for special quality and preparation and prices be posted 25 pct lower than the published prices for the lowest acceptable grades of strategic mica, giving the buyers authority to make intermediate prices according to the quality and preparation. It was thought desirable at the same time to announce prices for nonstra-tegic mica where such quality is being obtained in mines producing strategic mica and where it would be necessary to take the output in order to get the strategic mica. It was also suggested that the price of electric and black-spotted mica be 50 pct below the price of the lowest grade of strategic mica and the price of black-stained mica be 60 pct below the price of lowest grade strategic mica. The few experienced buyers available were employed but they were inadequate for the job and others had to be trained. All needed a guide or primer of some kind to attain systematic procedure and consistent prices in their respective buying areas. The Mica Buyers Guide was formulated for that purpose based on experience gained in the first six months of buying. The Preface to the original guide was as follows: The purpose of this guide is to serve as a text in training beginners and as a handbook for experienced buyers of the instructions which have been issued up to this time. At the meeting of prospective buyers last summer, it developed that the first essential to attain uniformity must be some kind of check sheet. Our "Mica Buyers Report" was developed for this purpose and forms the backbone of this guide. Price is determined according to size, quality and preparation. Size can be measured, but no system of measurement or machine has been devised which can be substituted for the trained eye of the buyer to deterrnine quality and preparation. Although the "One Price" system was instituted and the "Guide" not used, the buyers were required to continue making out a "Mica Buyers Report" (Fig1) with each lot of mica purchased. The form proved its value and there is no doubt that in another such emergency some similar form should be

Jan 1, 1950

By Jay F. Smith

The Alan Wood BOF Shop consists of two 140 ton furnaces with a rated yearly capacity of 1-1/4 million ingot tons, he hot metal for the BOF Shop is supplied by two 18 foot blast furnaces which produce an average of 2000 tons per day, To achieve the rated ingot ton capacity with this limited supply of hot metal, the preheating of scrap is necessary. This is accomplished in the furnace by using an oxygen-natural gas burner. Piping Arrangement The natural gas and oxygen are piped into the Shop through 8-inch lines to their respective valving stations. As can be seen from Figure 1, the flow of natural gas passes through a flow control valve which is common to both furnaces, after which it divides into two 6-inch lines forming two identical and independent gas control lines, one for each furnace.

Jan 1, 1972

By J. R. Linney

THE Eastern Magnetite Industry produced approximately 7,850,000 long tons of crude ore in 1945 from which was obtained approximately 3,650,000 long tons of shipping product or a ratio of 2.10 to 1. Lack of skilled or experienced miners was the greatest handicap. Veterans returning to work improved the underground labor shortage in some localities but as a whole the labor shortage was keenly felt throughout the industry. One cannot now predict what may be accomplished in 1946 but barring major steel strikes a worthwhile improvement can be expected. At the Richard mine of the Richard Ore Co., the shipping product for the year amounted to approximately 124,650 long tons of concentrate and lump ore. Crude-ore production was 160,600 long tons. The average analysis for lump ore was 63 per cent iron and for concentrates 66.05 per cent. The Warren Foundry and Pipe Corp. at their Mt. Hope mine produced 73,000 long tons of lump ore averaging 59.5 per cent and 57,000 long tons of concentrate averaging 67 per cent. The total mine hoist was approximately 209,000 long tons. Operations were commenced through the new Leonard shaft on Jan. 18; the Brown shaft through which operations had been conducted since 1912 caved beyond repair on Sept. 26. No one was injured but pumping facilities were somewhat disrupted. In order to reach designed capacity a total of 400 men will be required with 300 underground. Due to shortage of labor all operations in 1945 were concentrated on the 1700 level. As fast as men can be hired and trained development of the 2100 and 2500 levels will commence. Mt. Hope has a consider-

Jan 1, 1946

"With a total value to date of well over $200,000,000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $ 100,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper.Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade.In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1 924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.The known mineralized area of the district is found in a broad syncline striking north and south. The west limb plunges sharply and extends for a distance on its dip of approximately one and a half miles to the trough. The east limb raises gently through a distance of about two miles to the east limit of known mineralization. This general structure is broken by local faulting throughout the district, the local structural conditions playing an important part in the ore deposition. The north end of the fold is obscured by a rhyolite flow and the south end stops against a monzonite stock."

Jan 1, 1925

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

US 4,132,635 -In the froth flotation beneficiation of low- grade siliceous iron oxide ore, an aqueous pulp of undeslimed ore is conditioned first with a reagent formed by incorporating a water-soluble polyvalent metal salt into an aqueous solution of sodium silicate and then with oleic acid or other anionic collector and optionally pine 011 or other frother. The conditioned pulp is subjected to flotation to concentrate Iron oxide values in the froth D. C. Yang, assigned to Michigan Technological University Jan 2, 1979 7 pp (209-1 66) Filed 1-1 3-77 (759,094) Drawing below.) [ ] US 4,133,038-In the froth flotation beneficiation of copper sulfide ore or other ores, an aqueous suspension of a mineral sample of uniform grain size and composition is conditioned with a strongly adsorbable collector in an amount which is a fraction of the amount sufficient to create a monomolecular layer on the mineral grains, and the conditioning continued until the entire amount of collector is adsorbed The conditioned pulp is subjected to flotation, the floated particles separated at timed intervals, and the flotation rate coefficient determined. By varying the degree of adsorption in repeated treatments, the dependence of the flotation rate coefficient on the degree of adsorption may be determined A Nieml Jan 2, 1979 10 pp (364-502) Filed 12-7-77 (858,353) Priority Finland, 5-26-75 (75/1,525) Same: British 1,533,723, dated Nov 29, 1978 Same Canadian 1,065,066, dated Oct 23, 1979 US 4,133,746System and method for maintaining substantially steady state conditions in the froth flotation beneficiation of copper ore, molybdenum ore, or other metal ores The mass flow of flotation concentrate from the cell is monitored continuously, and the rate of admission of aeration air into the pulp in the cell is varied inversely with respect to variations in the mass flow control of rougher flotation cells is accomplished with a single valve G W Dopson, assigned to Magma Copper Co Jan 9, 1979 6 pp (209-1) Filed 11- 23-76 (744,306

Jan 1, 1980

[L. W. KEMPF, Chairman E. E. SCHUMACHER, Past-Chairman E. A. ANDERSON, Senior Vice-Chairman A. A. SMITH, JR., Vice-Chairman 11. A. MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N. Y. Executive Committee 1947 C. Y. CLAYTON A. B. GRENINGER CURTIS PIGOTT 1948 WALTER BONSACK W. A. DEAN LOUIS JORDAN 1949 J. D. HANAWALT W. A. JOHNSON E. W. PALMER]

Jan 1, 1946

By Paul M. Tyler

ROUGHLY one-half the value of mineral products at mines or quarries must be spent for wages. In view of the steady increase in hourly wages that continued for several decades prior to the onslaught of the recent depression, it is perhaps surprising to discover that labor's share of the gross proceeds of the mining and quarrying industries of the United States declined to 46.8 per cent in 1929, compared with 52.2 per cent in 1919 and 53.2 per cent in 1909. The actual percentages vary in different branches of the industry and in different localities but the downward trend is unmistakable. For the period 1909 to 1919 it was quite marked in every industry and from 1919 to 1929 it was apparent in all but six: namely, gold and silver lode mining, placer gold mining, crude gypsum production, marble quarrying, asbestos production, and fluorspar Tninino mining

Jan 1, 1933