Search Documents

By J. Szekely, V. Stanek

Steady state heat transfer and fluid flow rates are predicted for the counter-current contacting of gas and solid streams. For a .fixed pressure drop across the bed the convective heat transfer rate is affected by the gas flow rate, which in turn is affected by the temperature distribution in the system. Variations in bed voidage and in particle size were found to change the predicted temperature profiles quite markedly, in particular when the thermal capacities of the gas and solid streams were equal. IN Part I we examined the effect of step and pulse changes in the inlet gas temperature on transients in the flow of gases through fixed packed beds. Here we shall discuss heat flow and fluid flow interactions in the counter-current heat exchange between packed solids and a gas stream. Counter-current heat exchange in packed beds has been extensively studied. In his now classical paper, Furnas' assumed constant property values and developed a simple analytical. expression for the temperature profiles in the gas and in the solid stream. A highly sophisticated analysis of counterflow systems, allowing for transients and interparticle conduction was developed by Amundsen. In preparing a very readable review of this topic Elliott' also presented a number of elegant solutions, including the case involving heat generation. A great deal of work has been done on the application of these concepts to the modelling of the blast furnace. However, in all this previous work the mass flow of the gas was regarded as a quantity independent of the gas-solid heat exchange process. In the following we shall consider counter-current heat exchange between a gas stream and a packed bed of solids, under conditions where the pressure drop across the bed is specified, rather than the mass flow of the gas. FORMULATION Consider a packed bed, extending from y' = 0 to y' = L, in which moving solids and a moving gas are contacted in a counterflow arrangement. Let cold solids, with an initial temperature Tsi and mass flow GA, enter at y' = L, and hot gas with an initial temperature of Tgi and mass flow Gg enter at y' = 0. In contrast to the problems considered in Part I this system has a nontrivial steady state and we shall restrict our attention to the study of the pressure drop flow relationships and the resultant temperature distributions for steady state conditions. Under these conditions the formulation of the problem requires the statement of the following: 1) heat balance on the gas 2) heat balance on the solids 3) the mechanical energy balance equation and in addition the knowledge of the equation of state, and a functional relationship between viscosity and temperature and an expression for the heat transfer coefficient in terms of the other parameters. On neglecting temperature gradients within the solids and for a constant mass flow of the gas, the solution to this problem is well known.'" The expressions for the temperature profiles of the gas and solid streams may be put in the following form: where Tg and T, denote the dimensionless gas and solid temperatures respectively, y is a dimensionless distance, and R is the ratio of the thermal masses. These quantities are defined as follows: For the particular case of equal thermal mass capacities by the gas and the solid, that is R = 1, the Eqs. [1]and[2] simplify to Eqs. (71 and[8], respectively: i.e., the resultant profiles are linear. As for most practical cases , solutions given by Eqs. [7] and [8] will contain only the inlet temperatures as parameters. For a fixed, predetermined value of C;b the above

Jan 1, 1970

By S. S. Marsden, S. H. Raza

An experimental study of the flow of line-textured. aqueous foams through Pyrex tubes is described. The foams range in quality F (ratio of gas volume to total volume) from 0.70 to 0.96 and behave like pseudoplastic fluids. At lower flow rates they exhibit laminar flow ad have apparent viscosities which increase with quality, and which cover a range of 15 cp to 255 poise for tubes of 0.25- to 1.50-mm radius rj. At higher flow rates a plug-like type of flow is developed, the extent of which increases with both T and ri. When the same foams flow through either open or packed Pyrex tubes, remarkably high streaming potentials ?E are often generated. These can easily reach 50v if nonionic foaming agents are used, but are at least an order of magnitude less for ionic foaming agents. A linear relationship between ?E and the pressure differential ?p is observed; this usually extrapolates to positive values of ?p at ?E of zero. The slope of the line increases with both F and ri. An equation was derived to describe the streaming potential of non- Newtonian fluids in circular tubes and was used to correlate experimental results. The calculated < potentials are of the right order of magnitude. INTRODUCTION Foams are both unusual and inniguing in their physical properties, and have been the subject of many scientific studies. However, present knowledge of foams is still fragmentary, specific and often contradictory. Apparent viscosity of foam is the physical property of greatest interest to both rheo1ogists and engineers. sibreel reported that the apparent viscosity decreased with increasing shear rate in a manner similar to some non-Newtonian fluids. Penny and Blackman2 reported that fire-fighting foams had both a limiting shear stress and a tensile yield stress. There is little doubt that some foams at least behave like non-Newtonian fluids, and have apparent viscosities considerably higher than those of either constituent phase. The high apparent viscosity of foam with its concomittant effect on mobility ratio and sweep efficiency no doubt prompted several attempts by research groups to use foam as a displacing agent in porous media. Based on recent experience, most of these groups probably succeeded in completely blocking fluid flow in the porous media and then abandoned their efforts. Two groups apparently found the successful combination of experimental parameters at about the same time.3,7 Others have recently added to our knowledge of foam flow in porous media and its use as a displacing agent.8-13 An experimental problem encountered by Fried3 was a transient blockage of foam flow in porous media when distilled water was used to prepare the foam-producing solution. Fried surmised that this was due to an electrokinetic effect and he eliminated it by using electrolytes in preparing foaming solutions. He also measured the streaming potential of a number of foams in capillary tubes which he found to be appreciably higher than those obtained when the constituent liquid flowed under comparable conditions. This paper presents results of a more comprehensive study of the streaming potential generated by aqueous foam flowing in both open and packed Pyrex tubes. It also adds to knowledge of the rheology of these foams as deduced from their flow behavior in open tubes. APPARATUS AND PROCEDURE A diagram of the apparatus used is shown in Fig. 1. Details of its construction, testing and use are described elsewhere.14 Careful selection of materials, extreme cleanliness and rather elaborate electrical insulation and shielding were necessary to obtain reproducible results (±5 percent). Both streaming potential and streaming current were measured with an electrometer. The design of the foam generator developed for this work is novel (Fig. 2). It will produce uniform fine-textured foams at pressures sufficiently

By J. Geertsma

The relationship between porosity and the speed of propagation of acoustic waves in fluid-saturated porous rocks as measured by the Sonic log and by ultrasonic tecbniques is analyzed. Biot&apos;s continuum theory 1 is used to explain the difference in acoustic wave propagation between a dry and a liquid-saturated porous material. The porosity is a variable in this theory. However, the acoustic wave propagation in the dry rock depends too on porosity, and this dependence is not predicted by the theory. Frequently in dry sandstones, a nearly linear relationship between reciprocal acoustic wave velocity and porosity is observed in the low-porosity range. The physics behind this behavior is outlined. An empirical relationship of the form, 1/v = A + F, applies accordingly for many porous dry rocks, provided the porosity is the only variable. The presence of a liquid in the pores changes the value of B, and this change is found to be in agreement with the Biot theory. The time-average relation introduced some years ago2 results in an equation of the same type — 1/V = F/Vf + (1 - F)/Vr — but is not based on a sound physical picture. Still, this relation sometimes predicts approximately correct A and B values. Carbonate rocks with their complicated pore structures sometimes show a different relationship between wave velocity and porosity, unfavorable for log interpretation. Examples are presented. The simultaneous presence of calcite, dolomite and anhydrite, with their different grain densities and matrix compressibilities, complicates acoustic-log interpretation in carbonate rocks still further. Other complicating effects of acoustic-log interpretation are discussed. They are related to the influence of shale streaks and natural fractures on the average wave velocity observed by the logging tool and to the effect of adsorption phenomena on wave propagation in unstressed rocks particularly in sandstones. INTRODUCTION The velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity loggers of various d-sign may be used, for which velocity is defined as the. distance between a wave generator and a wave detector (one-receiver system) or the distance between two wave detectors (two-receiver system), divided by the shortest time required for a vibrational pulse to cross this distance. Velocity loggers ale used to assist in seismic prospecting, to differentiate between the various types of sedimentary rock layers, and also to determine rock porosity and pore fluid content. This paper is especially concerned with the relation between velocity and porosity and the effect of the pore fluid. Most velocity-log interpretation in terms of porosity is based on a formula advocated by Wyllie, et al,2 suggested earlier by Hughes and Jones,3 and known as the "time-average relation". This formula app1ies for a model consisting of a layered system of parallel alternating slices of a solid and a liquid, crossed by the wave path perpendicular to the interfacrbs. This must be an unsuitable model for the derivation of wave propagation properties of liquid-saturated porous media. It suggests that only rock matrix and fluid properties influence the wave velocity. The surprising fact, nevertheless, is that applications of this formula to clean sandstones under specific conditions (sufficient effective stress) results in porosity predictions which are close to reality. Other authors, such as Gassmann,4 White and Sengbush,5 Brandt,6 and Hicks and Berry,7 make use of more realistic models to arrive at a wave velocity formula for porous sediments. Their models consist of various liquid-saturated packings of frictionless spherical grains and are, therefore, also highly idealized. A number of experimental results obtained in the laboratory can be better explained with these model theories than by the time-average relation. A study of a general character, not depending a priori on a special model of the porous structure, was still lacking.

By A. W. D. Hills, M. R. Moore

An apparatus has been developed in which metals can bc solidified under closely controlled unidirectional heat flow conditions. The metals are cooled by a multiple-air jet system, designed so that the heat transfer coefficient is uniformly distributed over the cooled surface. They are contained in a special furnace system of low thermal mass which enables unidirectional heat flow conditions to be rigorously maintained for certain specific cooling rates. This apparatus has been used to study the solidijication of pure lead and pure tin at zero superheat, solid metal thicknesses being determined by thermal analysis, and by dipstick readings. Detailed thermal balances have been drawn up on the experiments in order to determzne the cooling conditions that most rigorously correspond to unidirectional heat flow. Solid metal thicknesses, measured experimentally for these conditions, have beetz shown to agree closely with the theoretical wedictzons of different integml-profile methods. lt is concluded that any errors inherent in the integval-profile method are no greater than the errors inherent in experimental investigations of solidification. A knowledge of the influence of heat transfer rates on the solidification of metals is essential to the understanding and control of industrial casting processes. Since very few formal methods are available for solving the heat conduction equation under solidification conditions several authors have developed approximate techniques for doing so. One of the most promising is the integral-profile technique that has been used by Goodman,1 Hills,2,3 Tien4 and Hills and ~oore&apos; to predict solidification rates under certain specific heat transfer coniditions. In the first of this present series of papers6 Hills has further generalized the method and developed a universal integral-profile technique that can be used to predict solidification rates under a wide variety of unidirectional heat flow conditions. Since the method is approximate it is necessary to investigate the accuracy with which it predicts actual solidification rates. A review of the literature7 shows that solidification rates have seldom been measured under accurately known heat transfer conditions and it was therefore decided to develop experimental techniques that would enable this to be done. Results obtained would then be available as a check on the approximate solutions already developed, and in the development of further solutions that would be applicable under more complicated conditions. The initial work in this experimental program which is described here, is concerned with the solidification of pure metals at zero superheat under unidirectional heat flow conditions. Subsequent experiments have been concerned with the solidification of pure metals at appreciable superheats, under varying unidirectional heat flow conditions and under two dimensional heat flow conditions. In a series of experiments recently initiated, the solidification of binary alloys is also being investigated. The results of these subsequent experiments, together with relevant theory, will be described in later papers. The solidifying metal has been cooled in all the experiments, by a multiple air jet system designed so that the heat transfer coefficient to the cooled surface is constant and is uniformly distributed over the surface. This type of system has been chosen since only one parameter is needed to specify the heat transfer conditions and since these conditions are analogous to those met in certain continuous casting processes.&apos; Air cooling was chosen in preference to water cooling, however, since it offers a wider range of heat transfer conditions, and since it can be investigated by analogous mass transfer techniques. The first part of this paper discusses the existing integral-profile solutions that correspond to the heat transfer conditions used in the experiments, and describes the development and use of the experimental apparatus. In subsequent sections the heat transfer and solidification results are presented, and the various theoretical predictions are compared with them, and with one another.

Jan 1, 1970

By David E. Nicholas

INTRODUCTION In this paper, a numerical process for selecting a mining method, with the emphasis on underground mass mining techniques, such as caving, induced caving, and stoping, is proposed. In the past, selection of a mining method for a new property was based primarily on operating experience at similar type deposits and on methods already in use in the district of the deposit. Then, the chosen method was modified during the early years of mining as ground conditions and ore character were bet- ter understood. Today, however, the large capital investment required to open a new mine or change an existing mining system make it imperative that the mining methods examined during the feasibility studies and the method actually selected have a high probability of attaining the projected production rates. Although experience and engineering judgment still provide major input into the selection of a mining method, subtle differences in the characteristics of each deposit, which may affect the method chosen or the mine design, can usually be perceived only through analysis of measured characteristics. The parameters that must be examined when choosing a mining method include: 1) geometry and grade distribution of the deposit; 2) rock mass strength for the ore zone, the hanging wall, and the footwall; 3) mining costs and capitalization requirements; 4) mining rate; 5) type and availability of labor; 6) environmental concerns; and 7) other site-specific considerations. This paper encompasses a detailed look at the first two parameters since they, plus mining costs, have the greatest impact on the selection of a mining method. The proposed method selection process is for a project where drilling has defined sufficient geologic reserves, but little or no underground development has been done. Since each deposit has its own characteristic geanetry/grade distribution, and rock mechanics properties, mining method selection should be at least a two-stage process. In Stage 1, the deposit is described in terms of geometry, grade distribution, and rock mechanics properties. Using these parameters, the mining methods can be ranked to determine which are most applicable; they can then be considered in general terms of mining and capitalization cost, mining rate, type and availability of personnel, environmental concerns, and other site-specific considerations. In Stage 2, the most likely mining methods are costed out, based on a general mine plan. Mining and capitalization costs are used to determine a cut-off grade fran which a minable reserve can be calculated; economic comparisons can then be made to determine the optimum mining method and economic feasibility. During the mine planning phase of Stage 2, rock mechanics information would be used to provide realistic estimates of underground opening size, amount of support, orientation of openings, and caving characteristics, and open pit slope angles. If ground control or operational problems should be encountered with the methods being considered, modifications could be made. Although planning on paper extends start-up time, it is cheaper to err on paper than to find the error after mining has begun. METHOD SELECTION - STAGE 1 The main purpose of Stage 1 is to select those mining methods which should be considered in greater detail. The simplest way to do this is by defining those characteristics required for each mining method and then determining whether the characteristics of the deposit are suitable. However, no one mining method is so restrictive that it can be used for only one set of characteristics, as indicated by the classification system proposed by Boshkov and Wright (1973). In the mining method selection proposed, geometry, grade distribution, and rock mechanics characteristics are ranked according to their acceptability for ten general mining methods.

Jan 1, 1981

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

By H. Biloni, B. Chalmers

Metallographic studies of the segregation of solute in and near the surfaces of chill-cast alloys have shown that, under sufficiently severe conditions, nucleation on the cold mold surface is followed by the formation of a disc of solid of the same composition as the liquid. This disc is surrounded by two concentric rings in which the concentration first decreases and then increases. The discs and rings are surrounded by a region in which arms of low solute concentration separate regions of high concentration. These arms start at the periphery of the outer ring and are initially radial; they make a gradual curved transition from the radial direction to a crystallographic direction. A normal dendritic substrcture is established beyond the position at which the arms have become crystallographically aligned. When the cooling is less severe, the disc becomes less irregular in shape and has a concentration minimum at the center. The term "Predendritic" is proposed for these transitions. A qualitative explanation is outlined for the phenomena observed at the surface and in the equiaxed region of the ingots. It is well-established1-&apos; that the normal mode of solidification for alloys under most conditions is dendritic. A characteristic of dendritic solidification is the growth of rods or plates in specific crys-tallographic directions. The remaining liquid solidifies later, usually with a higher concentration of solute than the original liquid. Very little is known, however, about the transition from a crystal nucleus until the dendritic pattern is established. It is clear that there must be a transition because the nucleus is much smaller than the characteristic spacings found in the "steady-state" structure. And it also seems clear that the initial conditions must be important since the undercooling existing during the nucleation of the grains has a remarkable influence upon the grain size4 and the segregation pattern. The present paper reports a study of the micro-segregation in regions where crystals have nucleated, and the conclusions that can be drawn regarding the early stages of growth, in connection with the details of the solidification process. Aluminum of 99.993 purity, A1-Cu alloys containing 0.5 to 20 wt pct Cu, and Pb-Sn alloys with 5 wt pct Sn were cast and examined metallographically at the as-cast surface, close to the surface, and in the interior after casting. The alloys were cast from controlled temperatures against surfaces at different temperatures ranging from room temperature to approximately the liquidus temperature of the alloy. The surfaces were, in various experiments, graphite, stainless steel, copper, and aluminum. The methods used for metallographic examination were as follows. 1) The Nomarski phase contrast interferometer6 was used to obtain information on the topography of the as-cast surface. 2) The distribution of any solute present in A1 99.993 pct and copper in the A1-Cu alloys was studied by the anodic film technique originated by Lacombe and Mouflard7 and previously applied in the study of the solidification of aluminum by Biloni.8 The electropolished surface of the specimen is anodized under controlled conditions so that the thickness of the oxide film and therefore the interference colors under white light are sensitive to the local composition. This technique was applied to the as-cast surfaces and to metallographically prepared surfaces from the interior. 3) If in Al-Cu alloys, the surface is anodically oxidized for several minutes, instead of seconds as in the color-film technique, the copper segregation is outlined by a different level with respect to the matrix. This method is less sensitive but complementary to that for the color films. 4) The distribution of copper revealed and mapped by the metallographic techniques was confirmed by electron probe. 5) In samples with high concentration of copper, evidence for the copper distribution could be seen optically after electropolishing.

Jan 1, 1965

By A. W. Schlechten, C. M. Hsiao

The apparent vapor pressures of a number of metal sulphides were determined by measuring their rate of weight loss when they were heated under vacuum. The calculated pressures are due in some instances to the volatility of the sulphide and in others to the decomposition pressure. FIE direct reduction of metallic sulphides, as in the precipitation method for lead or antimony, is not a widely used process today. However, it might be employed for the production of a number of metals if the operation were carried out under reduced pressures. Two general procedures are possible; the reducing agent could form a stable nonvolatile sulphide from which the valuable metal could be removed by volatilization or liquation. The other approach would be to choose a reducing agent which would form a sulphide that could be volatilized away from the valuable metal. A vacuum operation would serve to protect the sulphides and metals from oxidation and would increase the evaporation rates. A related process is the separation of metallic sulphides by selective volatilization either at atmospheric pressure or under vacuum. This procedure is already used commercially for the elimination of lead and cadmium as PbS and CdS from zinc calcines; it might well have other applications. To predict such processes it is necessary to know the relative volatilities of the metallic sulphides and to know whether they volatilize as sulphides or whether the predominant weight loss is due to decomposition. Such data would also be of value in studying problems such as the use of sulphides for refractories, as described by Brewer,] or in the evaluation of the theory of ore deposition from the vapor state, as proposed by Brown.&apos; Qualitative statements concerning the volatility of metallic sulphides can be found frequently in the literature and are well summarized by Mellor, but accurate determinations of rates of evaporation or vapor pressures are very scarce. Kelly" lists vapor pressure data only for PbS; his reference being to the work of Schenck and Albers,4 who measured the vapor pressure of PbS by a dynamic method between 850" and 995°C. More recently Veselovskii5 has determined the vapor pressures of the sulphides of antimony, lead, cadmium, and zinc at temperatures ranging from 360" to 1000°C using Knudsen&apos;s method. A second Russian worker, Pogorelyi,6 determined the vapor pressures of CdS and ZnS at temperatures from 900" to 1250°C. The results obtained by these workers are shown in subsequent graphs in comparison with the data of this paper. Brewer and coworkers1 have studied some of the metallic sulphides to determine their suitability as refractories in vacuum. Veselovskii&apos;s determinations on PbS checked well with those of Schenck and Albers, and his determinations of CdS check almost exactly with Pogo-relyi. For the vapor pressure of ZnS the data of Veselovskii and that of Pogorelyi are in fair agreement, as shown in Fig. 1, but it should be pointed out that Lumsden7 has discovered that the equation given by Veselovskii for the vapor pressure of ZnS: - 14,200 log P9.495 is in error by a factor of ten when compared to the experimental data. In contrast with the scarcity of data on vapor pressures, the decomposition pressures of many metal sulphides have been determined and are summarized by Smithells.8 Theoretical Considerations The experiments described in this paper consisted of determinations of the rate of weight loss of certain metallic sulphides under very low pressures at different temperatures. These data plus observation and analyses of the products reveal the mechanism of the weight loss and also provide a basis for the calculation of the vapor pressure or apparent vapor pressures of the sulphides.

Jan 1, 1953

By J. C. Wilhoit, E. M. Galle

A three-dimensional photoelastic study was made to determine the stress state around the wall and bottom of a wellbore due to fluid pressure within the wellbore and unequal principal geostatic stresses. Models simulating the wellbore were made from a phthalic anhydride-cured epoxy resin. The frozen stress technique of three-dimensional photoelastic-ity was used to determine the stresses within the model. Two separate problems were solved: (1) hydrostatic pressure on all sides of the model with the exception of the inside of the hole, and (2) uniaxial compression perpendicular to the center line of the hole. The results are presented in the form of contour curves for each stress component. The curves cover a region which extends several hole radii from the bottom and wall of the hole. By proper use of these results, the state of stress may be calculated for any point on the wall or bottom of the hole, as well as for any point within the material that surrounds the hole. A systematic method is given for calculating these stress components for any combination of fluid pressure within the wellbore and system of unequal principal geostatic stresses, provided one of the principal geostatic stresses is parallel with the wellbore. The results show that stresses around the wall and bottom of a wellbore, induced by an uneyual system of principal geostatic stresses, are appreciably different from those induced by geostatic stresses that are hydrostatic. For uneyual principal geostatic stresses, the experimentally determined stresses on the wall of the hole several radii from the bottom are in good agreement with the stresses calculated by elastic theory. INTRODUCTION Interest in the problem of determining the stresses around and near the bottom of a wellbore, due to geostatic loading and fluid pressure within the wellbore, originated in the petroleum industry. The stresses on the wall of the wellbore are of interest due to their relation to lost circulation during drilling, the fracturing of formations during squeeze cementing and hydraulic fracturing of producing formations. The stresses on the bottom of the hole are of interest to the drilling segment of the industry because to produce a hole in the earth it is necessary to remove material from the bottom of the hole. This removal of material is produced by structural failure of the rock, whatever the criterion for failure may be. Cunningham and Eeninkl have shown that for certain conditions the effect on drilling rate of the bottom-hole stresses caused by a hydrostatic overburden pressure is small compared to other effects. This question, however, needs further experimental and analytical investigation. Much information concerning the stresses on the walls of wellbores has been published considering both equal and unequal principal geostatic stresses. The problem of determining the stresses around the bottom of the wellbore is considerably more complicated. However, previous investigators have obtained numerical and experimental solutions to the problem for equal principal geostatic stresses. whitworth2 and woods3 have obtained numerical solutions. word415 obtained a three-dimensional photoelastic solution, Durelli and Deily 6 obtained surface stresses only by photoelastic means, and Cheatham and Wilhoit7 determined the stresses around the bottom of a short cylindrical cavity. While Miles and McGuire, Harrison and Kieschnick and Hubbert and Willis 10 obtained the stresses on the wall of a wellbore for unequal principal geostatic stresses, they did not concern themselves with the stresses near the bottom of the hole. The estimates made by Hubbert and Willis of the differences between the principal geostatic stresses indicate that, to obtain a satisfactory solution for the stresses around the bottom of a wellbore, unequal principal geostatic stresses should be considered. This work is directed toward obtaining such a solution. The materials in the earth&apos;s crust are nonhomo-geneous, permeable and anisotropic. Previous

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.&apos; Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By A. R. Gregory

A shear wave velocity laboratory apparatus and techniques for testing rock samples under simulated subsurface conditions have been developed. In the apparatus, two electromechanical transducers operating in the frequency range 0.5 to 5.0 megahertz (MHz: megacycles per second) are mounted in contact with each end of the sample. Liquid-solid interfaces of Drakeol-aluminum are used as mode converters. In the generator transducer, there is total mode conversion from P-wave energy to plain S-wave energy. S-wave energy is converted back to P-wave energy in the motor transducer. Similar transducers without mode converters are used to measure P-wave velocities. The apparatus is designed for testing rock samples under axial or uniform loading in the pressure range 0 to 12,000 psi. The transducers have certain advantages over those used by King, 1 and the measurement techniques are influenced less by subjective elements than other methods previously reported. An electronic counter-timer having a resolution of 10 nanoseconds measures the transit time of ultrasonic pulses through the sample; elastic wave velocities of most homogeneous materials can be measured with errors of less than 1 percent. 5- and P-wave velocity measurements on Bandera sandstone and Solenholen limestone are reported for the axial pressure range 0 to 6,000 psi and for the uniform pressure range 0 to 10,000 psi. The influence of liquid pore saturants on P- and S-wave velocity is investigated and found to be in broad agreement with Biot&apos;s theory. In specific areas, the measurements do not conform to theory. Velocities of samples measured under axial and uniform loading are compared and, in general, velocities measured under uniform stress are higher than those measured under axial stress. Liquid pore fluids cause increases in Poisson&apos;s ratio and the bulk modulus but reduce the rigidity modulus, Young&apos;s modulus and the bulk compressibility. INTRODUCTION Ultrasonic pulse methods for measuring the shear wave velocity of rock samples in the laboratory have been gradually improved during the last few years. Early experimental pulse techniques reported by Hughes et al.2 and by Gregory 3 were beset by uncertainties in determining the first arrival of the shear wave (S-wave) energy. Much of this ambiguity was caused by the multiple modes propagated by piezoelectric crystals and by boundary conversions in the rock specimens. Shear wave velocity data obtained from the critical angle method, described by Schneider and Burton4 and used later by King and Fate sand by Gregory, 3,6 are of limited accuracy, and interpreting results is too complicated for routine laboratory work. The mode conversion method described by Jamieson and Hoskins7 was recently used by King 1 for measuring the S-wave velocities of dry and liquid-saturated rock samples. Glass-air interfaces acted as mode converters in the apparatus, and much of the compressional (P-wave) energy apparently was eliminated from the desired pure shear mode. A more detailed discussion of the current status of laboratory pulse methods applied to geological specimens is given in a review by Simmons.8 A new shear wave velocity laboratory apparatus has been developed for testing rock samples under elevated pressures. This apparatus employs liquid-solid interfaces as mode converters. The technique for generating pure shear waves at liquid-solid interfaces was developed from studies of critical angle methods.6 Two identical transducers are placed in contact with opposite ends of the rock sample, one transducer acting as an ultrasonic energy emitter or generator and the other acting as an ultrasonic energy receiver or motor. The P-wave energy emitted from the piezoelectric crystal in the generator transducer is converted into pure S-wave energy at the Drakeol-aluminum

By H. Schwartzbart, J. R. Low

Annealed, .Poly crystalline, low carbon steel exhibits a phenomenon known as the "yield point." If such a steel is loaded in tension, the load increases steadily with elastic strain, drops suddenly, fluctuates about some constant load value for a time and then rises with further strain. The load at which the sudden drop occurs is called the "upper yield point"; the load at which deformation proceeds at constant load is known as the "lower yield point"; the amount of elongation at constant load is termed the "yield point elongation." Deformation which occurs during the yield point elongation is heterogeneous in nature, deformed metal existing next to undeformed metal. The drop in load from the upper yield point is concurrent with the formation of a band of deformed metal which usually appears at a stress concentration such as a fillet and at an angle of approximately 45" with the direction of pull. As deformation proceeds during the yield point elongation, the deformed region grows until the entire specimen has been strained an amount equal to the strain in the first band. A phenomenon very often associated with the yield point is that of strain aging. Aging in steels may be of two types: quench aging, or precipitation hardening, and strain-aging. Strain aging differs from precipitation hardening in that if the metal is merely strained instead of given a solution anneal and quenched, it then undergoes changes in properties similar to those observed in quench aging. The yield point effect and strain aging are most markedly exhibited by low carbon steel, but have been observed in other alloys. Numerous explanations for the mechanisms of both phenomena have been advanced, but the evidence for the acceptance of any of the hypotheses is incomplete. One of the explanations of the yield point phenomenon frequently proposed is that there exists a honeycomb of grain boundary material that supports the load above the yield strength of the ferrite and that when this network ruptures, the ferrite flows with no increase in load. This notion was first advanced by Dalbyl in 1913 and has been since put forward in more concrete form by many investigators. The testing of this hypothesis was, in part, the object of the present investigation. Similarly, the mechanism by which strain aging occurs remains to be explained. Presumably, it is a precipitation hardening phenomenon similar to quench aging, the precipitation being initiated by strain. However, it is not known whether the process is a solution and precipitation effect or a change in solubility due to strain. One obvious method of determining whether or not the yield point is a grain boundary phenomenon is to determine if single crystals exhibit a yield point. Low and Gensamer2 have shown that carbon and nitrogen are responsible for the yield point and aging in steel and that these effects can be eliminated by the removal of these elements through wet hydrogen purification. Single crystals that have been grown in wet hydrogen treated material must then be recarburized or re-nitrided in order to evaluate the effect of grain boundaries. In the present investigation, single crystals of iron which had been annealed in wet hydrogen to remove the carbon and nitrogen were cut into two specimens having the same orientation with respect to the tension axis. Of these, one specimen was pulled in tension in the wet hydrogen treated state and the other was carburized or nitrided and tested similarly. All the crystals were examined for a yield-point and strain aging. The grain boundary hypothesis for the explanation of the yield point in steel has been tested only indirectly previously. Arrowsmith,3 Andrew and Lee,4 Edwards and Pfeil,5 Fell,6 Ludwik and Scheu,7 Winlock and Leiter8 and others found a decrease in proportional limit and yield point effect with an in-

Jan 1, 1950

By P. L. Raffo, T. E. Mitchell

Single crystals of Ta-Re alloys have been deformed in tension and compression as a function of solute concentration and temperature. The temperature dependence of the yield stress is decreased by alloying. At low temperatures there is a minimum in the yield stress (at about 2 at. pct) as a function of concentration. Three-stage hardening was not observed in the alloys. Linear hardening rates, where observed, were characteristic of stage II in pure tantalum. At low temperatures and high concentrations, work softening was often prominent at high strains. Electron microscopy revealed that dislocations are mostly of screw orientation, although heavily jogged and cusped, and often occurring in dipole pairs. The alloys become more prone to cleavage with increasing rhenium content, due mostly to an increasing yield stress rather than a change in cleavage strength. Alloying apparently decreases the Peierls stress of bcc metals at low temperatures by facilitating kink nucleation at solule atoms on screw dislocations. Higher solute concentrations further increase the yield stress. Quantitative calculations and comparisons with other bcc alloy systems are made to show that the predominant hardening mechanism is due to the interaction of dislocations with misfitting solute atoms close to their slip planes. The interaction is so localized that the core dilatation of dislocations could be important. CONSIDERABLE interest has arisen in recent years concerning the mechanical properties of unalloyed bcc metal single crystals.&apos;-7 These and similar studies on polycrystalline materials have resulted in a considerable understanding of the macroscopic yielding characteristics8, 9 and the process of work hardening.&apos;&apos; This latter advance is due in a large part to the increased use of transmission electron microscopy in P I RAFFO junior Membar AlMF is Metallyureist Iewis such studies and the general observance of three stages of work hardening in the shear stress-shear strain curves. The properties of substitutional alloy single crystals of bcc metals have not been determined in as much detail as in the pure metals. Insufficient systematic studies have been made on the effect of alloying on the magnitude and temperature dependence of the yield stress or the stress-strain curves. The alloy systems which have been studied to some extent have been Ta-W,11, 12 Ta-Mo," Ta-Nb,12&apos;14 Mo-Re,15 W-Re,16 and alloys of iron with nickel,17 platinum,17 vanadium,18 and aluminum.18 A large body of data exists on Fe-Si alloys, but these have mainly been a result of the experimental convenience of using this material in place of unalloyed iron, rather than a comprehensive study of the mechanical properties of the alloy system per se. The present authors have previously reported additional data on the properties of Ta-Re, Ta-W, and Ta-Mo alloy single crystals.1g Some of the data on Ta-Re alloys will be described later in this paper. Briefly, single crystals of Ta-Re (1.2 to 10.6 pct), Ta-W (6.2 and 10.2 pct), and Ta-Mo (2.9 and 9.0 pct) were grown by the floating zone method in vacuum. Compression tests were performed in the temperature range 77" to 623°K. Slip was found to occur in Ta-Re alloys at 77&apos; and 298°K on the (~ll)[lil] system and slip lines were coarser and straighter than in unalloyed tantalum. No three-stage hardening was observed in any of the alloy systems and the curves were nearly parabolic. At temperatures above 175°K the yield stress* increased monotonically with in- creasing composition while at 77" and 175°K the yield stress initially passed through a minimum after which it began to increase again for concentrations greater than about 2 pct Re. Similar minima were observed in Ta-Mo alloys and to a lesser extent in Ta-W alloys. The minimum was interpreted as being a result of a

Jan 1, 1969

By R. V. Smith

The theory for unsteady radial flow of gas, as simplified by Aronofsky and Jenkins, has been reviewed and compared with actual well performance. This study indicated that the theory should be modified by the introduction of an empirical "rate of flow" function "Y(q)". The expansion of the theory on the flow of gas to include a Y(q) term bridges the gap between the theory of unsteady-state flow of gas and actual gas-well behavior. Apparently, the Y(q) term is a function only of the rate of flow for a given well. The completion factor or skin effect is associated with the Y(q) function in such a manner that at least two or more sets of drawdown or pressure build-up tests are needed to separate the Y(q) function and the completion factor. Since the Y(q) function used in this report represents an energy loss dependent on rate of flow near the well-bore of a gas well which is in addition to the loss required by Darcy&apos;s law, the Y(q) function is related to the exponent of the back-pressure curve for a gas well. Techniques and equations are presented which permit the estimation of stabilized and "short-time" deliver-abilities. INTRODUCTION The published theory of radial unsteady-state flow of gas through porous media may be divided into papers1-" which use Darcy&apos;s law as a premise and other papers4-7,16-10 which recognize that Darcy&apos;s law may not hold for flow into gas wells. Miller8 compared theory based on Darcy&apos;s law with actual gas-well behavior and concluded that flow into gas wells deviates from Darcy&apos;s law. Houpeurt4,5 in a thorough investigation of flow into gas wells concluded that the flow rate into a gas well is proportional to the difference between the squares of upstream and downstream pressures elevated to a power between 1.0 and 0.5. Houpeurt also concluded that the deviation from Darcy&apos;s law is caused by irreversible, kinetic energy exchange between the flowing gas and the porous media. Tek9 presented a complete evaluation of the flow problem in gas wells. Several investigators state that the inclusion of gas compressibility into flow equations based on Darcy&apos;s law does not begin to explain the flow problems suggested by gas-well behavior. For many years, natural-gas engineers have realized that gas wells by actual test exhibit behavior which cannot be explained entirely by Darcy&apos;s law. Many tests on gas wells have indicated that a value of 0.85 for the exponent in the back-pressure equation is a fair average for many wells. However, Darcy&apos;s law either for steady or unsteady-state conditions indicates that the exponent should be 1.0. The purpose of this paper has been to examine this deviation from Darcy&apos;s law and to present a reasonable mathematical means of evaluating the deviation. The method presented in this paper combines previous theory with an empirical function to provide a description of gas-well behavior. All equations in this report are for constant terminal-rate-of-flow conditions. While present methods of testing wells usually are not based on this concept, they are believed to approach the constant terminal-rate conditions closely in many tests. However, several gas wells were tested by holding the rates of flow constant in order to approach more closely the constant terminal rate of flow; the results confirm the concepts presented in this paper. REVIEW OF THEORY FOR UNSTEADY-STATE FLOW OF GAS The basic partial differential equation for the flow of natural gas has been given in technical literature; the equation for a cylindrical reservoir with the well in the center is

By R. F. Blakely, P. E. Potter

Any stratigraphic section or bedding sequence can be synthesized if there is a transition procedure from one lithology or bedding type to another, and if thickness distributions of the different lithologies are known. Stratigraphic sections of a fluvial sandstone body were synthesized with five bedding types: cross-bedding, massive beds, parting lineation, ripple mark and mudstone. The transition procedure from one bedding type to another used dependent, Markovian random processes which have a memory that extends one step backward in the depositional process. As observed in nature, median grain size and sand wave thickness (cross-bedding and ripple mark) decline upward in the synthesized sections as proportions of the different bedding types change. Grain size and permeability were also incorporated into the sections. By changing the transition procedures, bed thickness distributions, rate of upward decline or sand wave height and length, different types of sections can be synthesized, thus making it possible to model many different sedimentation problems. INTRODUCTION This paper describes a general method for synthesizing stratigraphic sections and bedding sequences of sedimentary, metamorphic or igneous origin. Synthetic generation is of interest for several reasons. Close correspondence between real and synthetic sections suggests that the factors used in the synthesizing model may indeed be the correct ones, thus giving the investigator a check on his assumptions. Rapid, inexpensive simulation of many stratigraphic sections permits one to synthesize a rock body (sandstone or carbonate reservoir) or, on a larger scale, the fill of a sedimentary basin. Harbaughl gives an example of mathematical simulation of a carbonate basin. He simulated the basin in the hope that improved prediction would follow better understanding of the depositional processes. From the petroleum engineer&apos;s viewpoint it seems reasonable to believe that the synthetic generation of rock properties and their distribution in a reservoir should be relevant in the study of reservoirs. Any stratigraphic section or bedding sequence can be generated provided there is a transition procedure from one lithology or bedding type to another, and provided the thickness distributions of the different units are known. The transition procedure involves random processes that are either independent or dependent. If the depositional process is independent, previous deposition will have no influence on present deposition. However, if it is dependent, past deposition will influence either present or future deposition. Such a dependent depositional process can be thought of as having a memory that extends backward in time through one or more pulses of deposition. A process with a memory can be described by a Markov process. Because the concept of memory or dependence appears to be in accord with our understanding of many depositional processes, Markov processes were used to synthesize the bedding sequences of this study (see Appendix). The above methods are perfectly general and are appropriate for any stratigraphic section or bedding sequence: bedding types in a beach deposit, an evolving carbonate bank or the changing lithologic fill of a thick geosyncline sequence. We chose to synthesize a vertical profile of a fluvial sandstone body because its characteristics were well documented, much was known about fluvial processes and fluvial-deltaic sandstone bodies constitute an important class of petroleum reservoirs. CHARACTERISTICS AND ORIGIN OF FLUVIAL CYCLE The fluvial cycle has been well documented in recent years by Bersier,2 Allen3-5and Visher.6,7 Deposits from fluvial cycles range from 10 to 150 ft or more in thickness and are characterized by a "fining upwards": coarse sandstones with occasional conglomerates grade upward into medium- to fine-grained sandstone, and hence into siltstone and mudstone. The dominant sedimentary structure is inclined bedding: thick cross-beds in the lower half

By Matti J. Saarivirta

The relative machinabilities of the precipitation-hardenable Cu-0.9 pct Cr, Cu-0.25 pct Zr, and Cu-0.9 pct Cr-0.25 pct Zr alloys are improved from 18 to 80 pct by 0.75 to 1.25 pct Pb. The Lead also improves the tensile strength, hardness, ad resistance to softening of the Cu-Cr and Cu-Cr-Zr alloys. When the alloy containing 0.7 to 2.2 pct Cr, 0.10 to 0.25 pct Zr, 0.75 to 1.25 pct Pb, and balance copper is solution-annealed at 1000°C (1830°F) and then aged at 525°C (Y75°F), tensile strength of 65,000 psi, 16 pct elongation, 62Rb hardness, and 84 to 87pct IACS electrical conductivity are obtained. The copper base Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys have high electrical and thermal conductivities, high strength and resistance to softening at elevated temperatures, but their machinability is poor, i.e., close to that of the pure copper. In the manufacture of various components such as welding electrodes or electrical and thermal conductors it is ofter desirable that the alloy have good machinability for high production rates and long tool life. Thus, alloys that combine these properties may be used not only for existing applications, but for new ones where good machinability is a requirement. This investigation was undertaken to improve machinability without impairing other desirable characteristics of the Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys. These commercial alloys contain about 0.4 to 1.2 pct Cr, 0.10 to 0.25 pct Zr, and balance copper. Lead was selected as an element that should improve the machinability and possibly other characteristics of the alloy. WORK PROCEDURE This investigation began with a study of the effect of lead on the hardness, tensile strength, electrical conductivity, and machinability of the binary alloy containing 0.10 to 1.30 pct Cr and balance copper. This was followed by an investigation of the effect of lead on the Cu-0.1 to 0.4 pct Zr and Cu-Cr-Zr alloys. The alloys were made from initially oxygen-free copper and for comparison some castings were made from phosphorus-deoxidized Lake Copper. Commercially pure chromium, zirconium, and lead were used for alloying. In melting the chromium was added to molten copper at 1400°C (2550°F), the heat held for 15 min at temperature, and the temperature then lowered to 1350°C (2460°F) when the other elements were added. The alloys were held for 15 min at this temperature and cast into a cast-iron mold. One-kilogram, 3-in.-diam castings were made. An argon cover was maintained during melting and casting to prevent oxidation. The chemical compositions of the alloys are shown in Table I. The micro structure and properties of the alloys were studied in the cast and wrought conditions prior to and after various solution-annealing and heat-treating cycles. The relative machinability was determined as a function of the lead content and compared with the free-machining Cu-lpct Pb alloy. To determine the machinability, 13/16-in.-diam cast specimens were cut by a machine hack saw using a constant cutting speed of 50 fpm, a fixed feed force, and a new blade for each alloy specimen. Molybdenum highspeed steel saw blades, 0.032 in. thick with 14 teeth per in., were used in all tests. No cutting fluid was used. Five tests were made on each specimen and the average elapsed time per test was taken as a measure of the relative machinability for that alloy. The variation of cutting time for each alloy was less than 110 pct.

Jan 1, 1969

By W. A. Backofen, D. H. Avery, W. F. Hosford

Sheets of the magnesium alloys AZ31B, HK31A, and ZE10A in several different tempers were tested in tension and determinations were made of the ratio of width-to-thickness strain. A marked increase in the ratio with tensile straining and a dependence upon alloy and test direction are rationalized in terms of a balance between the amounts of basal and prism-plane slip. All such variations are related, in turn, to the prevailing crystallographic texture. Fracture appearance is explained on the basis of anisotropy in plastic flow, and implications for developing texture -hardening effects in these alloys are discussed. ThE crystallographic texture or preferred orientation of a given material is determined by details of processing history. Such texture is known to influence many aspects of material behavior, in particular both the yielding and strain-hardening characteristics which are of special interest in the present work. Traditionally, the resulting plastic anisotropy has not been regarded as especially desirable. Earing in drawn sheet is perhaps the most common example of an unwanted effect of texture. However, it has also been recognized that suitable textures may be usefully employed to improve drawability,1,2 as a specific example, and generally to control yielding resistance under combined-stress loading.374 Texture would seem to be a detail of structure not yet exploited to nearly the fullest extent. A convenient basis for characterizing anisotropy in plastic behavior is the ratio of width-to-thickness strains obtained in a tension test;5&apos;6 the parameter is frequently labeled "R" and its value is revealing with respect to the nature of the prevailing texture. R gives a useful measure of a material&apos;s "thinning resistance". For an isotropic material, R = 1. With R > 1 the increased through-thickness strength in a sheet means greater resistance to yielding under biaxial tension, or "texture hardening";3&apos;4 if R < 1 the result may be a "texture softening" under the same loading conditions.4 Most R data relate to steel sheets for deep-drawing applications. Values for steel and other materials of cubic structures are not often much greater than 1 and nearly constant with strain in testing.1,2,7,8 To explore the implications of plastic anisotropy further, it was felt that experiments with much more strongly textured materials would be useful, and this led to the choice of magnesium alloys. The "ideal" sheet texture for magnesium contains the (0001) plane in the rolling plane, which ought to lead to R values approaching infinity. However, departures from the ideal texture, the possibility of slip in non-close-packed directions, and deformation by twinning would all be expected to introduce some range of R. Accordingly, studies on these materials were undertaken. EXPERIMENTAL Alloys in sheet form, Table I, were selected to obtain a variation in crystallographic texture, in the expectation that this would be reflected in differences in plastic anisotropy. Pole figures constructed by the Schulz surface-reflection technique9 were provided with the experimental materials by the Dow Metal Products Co. Profiles of pole density along great circles through the rolling (0 deg) and transverse (90 deg) directions were prepared from the pole figures and are collected in Figs. 1 and 2; considerable departure from the "ideal" (0001) alignment in the rolling plane is evident, with the largest angular spread in both directions being found in the ZEl0 alloy. Results of tensile tests on full-thickness specimens of 6-in. gage length by 1/2-in. width are given in Fig. 3 as engineering stress-strain curves* in rolling and transverse directions. All tests but one were made at a constant drive rate of 0.02 in. per min, and the final values of percent elongation at fracture, over the initial 6-in. gage length, are noted at the ends of the curves; one test on ZE10A-

Jan 1, 1965

By Michael A. Gustafson, Fernando B. Sotelino

INTRODUCTION The degree of success of any new project will ultimately depend on two factors: (i) the underlying economic strength of the project; and (ii) how successfully the parties involved can coordinate their interests to establish a financing structure which indeed capitalizes on the project&apos;s inherent economic attractiveness. A project&apos;s underlying economic attractiveness is determined by its inherent comparative advantage in accessing the factors of production, combining these factors of production to create a product and marketing this product. Initially, the decision regarding whether to go ahead with the project - the go/no go decision - has to be based on its total ability to generate cash flow returns to project participants to compensate them for resources committed and risks undertaken. The extent to which project sponsors will actually benefit from the project&apos;s inherent economic attractiveness is fundamentally dependent on their ability to establish the long-term financing arrangement which best meets the objectives and constraints of each project participant and sources the most advantageous funding. The decision regarding the financing of the project, the "how-to-go" decision, is then an attempt to find the capital structure, consistent with market terms and conditions and sound financial management policies which will best: (i) match planned outflows with cash inflows; and (ii) maximize the return for project sponsors. This article makes use of a case study to illustrate the analytical process involved in dealing with the go/no go and the how-to-go decisions on a project. Though most commonly applied to project finance situations, the guideline described herein is equally applicable to other financing situations, such as leveraged buyouts and debt restructurings, where timely repayment of debt depends largely on the future cash flows to be generated by the entity being financed. Our case study is of a hypothetical expansion of an existing copper mining operation in Latin America. The company, Latin American Copper (LAC) currently has 147 million metric tons of proven sulphide ore reserves. The existing mine complex consists of an open pit mining operation and a conventional flotation plant with a processing capacity of 20,000 metric tons of ore per day. LAC sells copper concentrates primarily to Japanese custom smelters. The mine has been in operation for 5 years, fine copper production last year was 108,240 metric tons, and LAC currently has assets of $175 million and net worth of $135 million. Due to a recent increase in proven reserves, LAC is considering doubling the treatment capacity of its flotation plant to 40,000 tons per day, and expanding its mining capacity to meet the additional concentrator capacity (the "Project"). Project capital expenditures and incremental working capital have been estimated at approximately $210 million. The construction period is expected to cover one year, including a three-month start-up phase. The Project is to be funded by a combination of equity, senior debt, including both supplier credits and/or commercial bank term loans, and subordinated debt. LAC&apos;s shareholders are willing to commit a maximum of $50 million to the Project. A government development agency, which is also a minority shareholder, might be willing to lend approximately $40 million to LAC in the form of subordinated notes, depending on the ability of the Project to generate foreign exchange reserves. Commercial banks cannot be expected to offer loans with maturities longer than ten years. The Project is expected to increase the value of the firm because: (i) It will solidify the Company&apos;s position as a low-cost copper producer by taking advantage of economies of scale. As a result of the expansion, cash production costs are expected to decrease 7.0[c]/lb. and all-in costs 11.0[c]/lb; (ii) The potential earnings stream from the sulphide ore reserves will be realized

Jan 1, 1985

By A. M. Gaudin

Activation of sphalerite with silver ions results from the exchange of two Ag ions for one Zn ion in the sphalerite lattice. The exchange is proportional to the logarithm of time and proceeds until either of the reactants is consumed. Sodium cyanide prevents the activation of sphalerite by controlling the ratio [Zn++]/[Ag+]&apos; in solution. If sphalerite has already been activated with excess silver, cyanide ions can deactivate sphalerite provided oxygen is present. SOLUBLE: silver salts are effective activators for flotation of sphalerite with potassium ethyl xan-thate as collector.* Since sphalerite takes up large quantities of silver ions rapidly,2-4 investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hy-drosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Ii&apos;inally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure. The specific surface of two samples from the 65/100-mesh sphalerite stock, measured by krypton gas adsorption," was 420 cm2 per g. Compared with spheres of the same size and specific gravity, the prepared mineral had five times as much surface. Results of a wet chemical analysis and of a spectro-graphic study are given in Table I. Manganese, nickel, tin, indium, thallium, cobalt, and magnesium were not detected spectrographically. All solutions were preparid by -adding reagent-grade chemicals to conductivitv water. which had been previously saturated with the desired gases. Nitrogen and oxygen were purified, but no attempt was made to purify the laboratory air. Radioanalysis was carried out with prepurified Ag110 tracer obtained from the Oak Ridge National Laboratory. The complete decay scheme for Ae is complex. Its primary emissions are 0.09 and 0.55 mev ß rays and 1.48 mev y raysB and its half-life is believed to be 270 days. In preparation of solutions of AgNO3, the amount of Ag110 added was negligible compared to that of the inert silver. Abstraction of silver from solution by sphalerite was measured after agitation of 1.5 g sphalerite with 20 ml of solution in 50-ml pyrex flasks. All sample preparations were carried out in a dry box so that the proper atmosphere could be maintained. After the mineral had been agitated in the silver nitrate solution, an aliquot of the solution and a sample of the wet mineral were transferred to separate counting vials and weighed. The solid sample was dried and re-weighed and the activity in both vials measured by means of a scintillation counter. With scintillation counting it is possible to count y radiation from the solid and liquid, a distinct advantage over the older ß-ray counting techdiques.4 All measurements of silver activity were made using a sodium-iodide well-type scintillation counter. The amount of zinc in solution was measured colorimet-rically by the monocolor method of Sandell.7 Activation Studies Exchange Between Zinc Ions and Silver Ions During Activation: The increase of Zn++ in solution during activation with Ag+ is shown in Table 11. These data indicate a replacement of one Zn++ by two Ag+. Analysis of a separate two-month agitation test indicated that the replacement of Zn++ by Ag+ was, as expected, in the molar ratio of 2.0.

Jan 1, 1958

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962