Search Documents

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By Bunting S. Crocker

Bunting S. Crocker (Executive Vice President, Kilborn Engineering Ltd., Toronto, Ont., Canada)-This is an interesting report on laboratory-scale testing with pebble charges in 12-in.-diam mills, and the author correctly concludes that useful laboratory testing can be done. In the opening paragraphs he states, "laboratory pebble-milling tests have been considered too difficult to perform and not relevant enough to the actual grinding situation"!! This is definitely not so! The writer published detailed tests done in a 12-in.-diam mill comparing pebble and steel balls in 1952 6 and again in 1954 7. We note that our review paper in 1963 was the only one mentioned in the References. The author states that "a smooth lining is more frequently used in commercial-scale pebble grinding." The writer has designed some 22 plants treating 134,000 tpd in North America and Australia. He has also visited pebble installations in Norway, Sweden, Finland, and South Africa. All these plants correctly use heavier lifters than would be considered standard for ball mills of a similar size. Smooth liners are not recommended in wet ore treating plants. In the 1952 paper6 it was clearly demonstrated in the test work that the individual ore pebbles had to be the same weight-not the same diameter or size-as the steel balls if comparable grinding results were to be obtained. In the tests performed in this study most of the pebbles "passed 50-mm round hole screen openings and remained on a 40-mm round hole sieve. Correspondingly most of the ball mill experiments were performed with 50 or 40-mm steel balls". Thus, the balls and pebbles were essentially the same size or diameter. This means we are comparing apples and oranges. When the feed being ground is fine enough the pebbles will be superior. When the feed is coarse the steel balls will be the better. This is similar to grinding tests in which two sizes of steel balls are compared. In the middle of the article, "Crocker5 has reported that equal weights of pebbles and steel balls achieve the same grinding capacities under similar conditions …", then he proceeds to question this postulate. In the eight reports that I have published, I have never made this statement. What I have said is "for comparable grinding, the individual pebbles in the mill charge should be the same weight as the individual steel balls." This is not the first time that I have been misquoted on this point! It is most unfortunate that this test work has been done with a ball and pebble of the same diameter and not the same weight. It is impossible to properly evaluate the results. I also regret the fact that the screen analyses of the tests were not shown. Many of us who have been 40 years or less in the grinding game can easily read screen analyses at a glance. We can tell whether the top meshes are being ground by the ball charge, etc., etc. The graphs are fine for the summary or to illustrate conclusions but are often misleading in the report itself. However, we do agree that useful pebble grinding tests can be done in a 12-in. mill.

Jan 1, 1973

By R. L. Perrine

The rise of drain holes drilled from a well to improve productivity is becoming increasingly common. This paper presents data on the productivity increase that may he expected. The data were obtained by use of an electrolytic tank mode1 of a reservoir. Parameter varied in the study to show their effect on productivity include the length, number, and arrangement of drain holes, formation thickness, and damage near the well-hore. The most important results are that very large increases in productivity can be expected only ill damaged wells. The distance, to which drain holes penetrate is of primary importance. Additional length is more effective than increasing the number of drain holes. INTRODUCTI O N In planning the use of drain holes to improve productivity, it is important to he able to estimate the increase in production that can be obtained for a given expenditure. It is also important to know what combination of parameters related to the use of drain holes can he chosen to give the largest production increase. This paper presents data on the productivity increase that may be expected, as obtained by use of an electrolytic tank model of the reservoir. In this study, :! number of parameters were varied to show their effect on productivity. These included the length, number, and arrangement of the drain holes. The presence or absence of a damaged zone of low permeability around the well-bore and the thickness of the producing formation were also considered. The productivity increase that might be expected due to drain holes is presented as the ratio: productivity of a well after drain holes are drilled and completed to the productivity of the same well in an undamaged state without drain holes. The symbol Q/Qo is used to represent this productivity ratio. Thus, the comparison in each case is with a formation of uniform and undamaged permeability. Additional notation includes I;, for the radial extent of the damaged zone, which is assumed to be cylindrical and concentric with the wellbore. Thus the effect of an actual block is approximated by a discontinuous varia-tion in permeability. For purposes of this paper, the permeability within the damaged zone, denoted by kb, is assumed to be 1/25 that in the remainder of the formation, or k. A necessary assumption in making comparative tests using an electrolytic model is that reservoir flow behavior can be approximated by single-phase, steady-\tate flow according to Darey's Law. In addition, the formation must be assumed to be homogeneous with equal horizontal and vertical permeability. The well-hore diameter in this study is assumed to be 11¾ in. and the drainage radius of the well equal to 500 ft. The drain holes are considered to have been completed without damage. THE ELECTROLYTlC MODEL 'She producing formation was modeled by forming a sheet of phosphor-bronze into a cylinder 40% in, in diameter to represent the boundary of the drainage area. This was enclosed in a waterproofed plywood box, and the box filled to an appropriate level with a dilute sodium chloride solution. Solution concentration was adjusted to give a total resistance from

Jan 1, 1956

By M. M. Slotnick

It was once aptly said that a sign of approaching senility is ceasing work on a subject and beginning to talk about it. Perhaps that explains why, after many Years in which Part of my duties has been the training of college men in various branches of petroleum exploration geophysics, I have now begun to talk about it. In making an outline of what I believe ought to be discussed under the general heading of the title, I found it almost impossible to subdivide the ideas into an ordered set of discrete subjects. Rather, the pertinent remarks seemed to interlock almost everywhere. The consequence is that it will be necessary to start with the conclusions and then try to justify them by jumping back and forth. However, based on the types of men with whom I have had to deal, the subject naturally divides itself into two parts. In the first part, I should like to deal with the case of those undergraduates whose natural bent is toward the physical sciences and who may decide to enter the geophysical fold as a career. The other part will deal with those many men, geologists and engineers for the most part, who have drifted into exploration geophysics by one means or another, and whom it is necessary to train for geophysical work while they are occupied in their routine jobs. Here it may be in point to remark that most men in exploration geophysics at Present have been developed from precisely the latter group, and that the problem of training here is of great importance even though, in this paper, it will perforce occupy the secondary place. Training oF a Geophysicist The outstanding reason for the perplexing problem on the training of a geophysi-cist is that ideas differ on the answer to the question: "what is a geophysicistp" ln any of the scientific "specialties," like physics, for example, it is relatively simple to pigeonhole a man as being qualified to call himself a physicist. That appellation applied to an individual does not mean that he has mastered only the branches of intellectual endeavor usually associated under the broad name of "physics." we expect him also to have a more than mere acquaintance with mathematics and chemist~ and some understanding of most of the other sciences. But note this important point—we expect our physicist, whom we have chosen as an example, to be intelligently trained so that, if necessary, he can and will know how and where he can get the proper information on a subject in which he is not a specialist; he will know how to absorb that information and turn it to his uses. It seems to me that this is the outstanding characteristic of a man who can truly call himself a scientist: that he is a specialist in one of the broad branches of science in that he has enough training and discipline in the scientific approach so that, when called upon to do so, he can inteugently absorb knowledge from another bordering science (and all sciences not only border upon one another to some extent, but more often, overlap One another), and

Jan 1, 1946

By M. M. Slotnick

It was once aptly said that a sign of approaching senility is ceasing work on a subject and beginning to talk about it. Perhaps that explains why, after many Years in which Part of my duties has been the training of college men in various branches of petroleum exploration geophysics, I have now begun to talk about it. In making an outline of what I believe ought to be discussed under the general heading of the title, I found it almost impossible to subdivide the ideas into an ordered set of discrete subjects. Rather, the pertinent remarks seemed to interlock almost everywhere. The consequence is that it will be necessary to start with the conclusions and then try to justify them by jumping back and forth. However, based on the types of men with whom I have had to deal, the subject naturally divides itself into two parts. In the first part, I should like to deal with the case of those undergraduates whose natural bent is toward the physical sciences and who may decide to enter the geophysical fold as a career. The other part will deal with those many men, geologists and engineers for the most part, who have drifted into exploration geophysics by one means or another, and whom it is necessary to train for geophysical work while they are occupied in their routine jobs. Here it may be in point to remark that most men in exploration geophysics at Present have been developed from precisely the latter group, and that the problem of training here is of great importance even though, in this paper, it will perforce occupy the secondary place. Training oF a Geophysicist The outstanding reason for the perplexing problem on the training of a geophysi-cist is that ideas differ on the answer to the question: "what is a geophysicistp" ln any of the scientific "specialties," like physics, for example, it is relatively simple to pigeonhole a man as being qualified to call himself a physicist. That appellation applied to an individual does not mean that he has mastered only the branches of intellectual endeavor usually associated under the broad name of "physics." we expect him also to have a more than mere acquaintance with mathematics and chemist~ and some understanding of most of the other sciences. But note this important point—we expect our physicist, whom we have chosen as an example, to be intelligently trained so that, if necessary, he can and will know how and where he can get the proper information on a subject in which he is not a specialist; he will know how to absorb that information and turn it to his uses. It seems to me that this is the outstanding characteristic of a man who can truly call himself a scientist: that he is a specialist in one of the broad branches of science in that he has enough training and discipline in the scientific approach so that, when called upon to do so, he can inteugently absorb knowledge from another bordering science (and all sciences not only border upon one another to some extent, but more often, overlap One another), and

Jan 1, 1946

By E. T. Clymer

It has been the custom, from the earliest time, to grade pig-iron by the appearance of the fracture; and although, since the pneumatic and open-hearth methods of steel-making have come into existence, chemistry has been called to the assistance of the steelmaker in selecting material for his use, the consumers of forge- and more especially of foundry-iron, still rely almost entirely, as they did a hundred years ago, on the appearance of the fracture of the pig to guide them in the choice of iron. To this rule, however, each year sees more exceptions; and there are now many foundry-men

Jan 1, 1893

(There are 70 Student Chapters in the United States, 2 in Canada) University of Alabama-University, Alabama, Mining and Metallurgical Society, Win L Mason University of Alaska-College, Alaska, Mining Society of the University of Alaska, E H Beistline University of Arizona-Tucson, Arizona, Miners Society Birmingham-Southern College-Birmingham, Alabama, Pick and Hammer Club, Daniel D Arden University of British Columbia-Vancouver, British Columbia, G M Dawson Club, H C Gunning University of California-Berkeley, California, Mineral Technology Association, W H Somerton Carnegie Institute of Teehnology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of -Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann

Jan 1, 1956

By George G. Binder Jr., James W. Lacey, Arthur L. Draper

An experimental investigation of miscible fluid displacement has been made in linear porous media under highly adverse mobility ratio conditions. Various refined oils were displaced at field rates by liquid propane in both horizontal and vertical models 9 to 36 ft in length. In horizontal tests, mixed zones or transition zones form between the two liquids early in the displace-lents. Initially, the zones grow rapidly. III 2-in. diameter models, the mixed regions become nearly stable zones from 6- to 20-ft long. From then on these quasi-stable zones apparently grow only by molecular diffusion. The lenghts of the quasi-stable zones appear to be almost independent of the core material in which displacement;; are made and increase with increasing rates of injection and oil/solvent viscosity ratios. The lengths of the quasi-stable zones. measured in 2-in. diameter models at viscosity ratios and injection rates anticipated in the field indicate that essentially piston-like displacements of oil by solvent would occur. However, the mixed zone lengths increase markedly as the model diameter increases. In vertical displacements controlled by gravity drainage, only short trans-sition zones form. The entire lenghts of these zones can be accounted for by molecular diffusion. Therefore, in reservoirs having characteristics allowing a high degree of gravity drainage, nearly complete oil recovery should be attainable by miscible fluid displacement. INTRODUCTION The oil industry is faced with an ever increasing cost for finding new oil reservoirs. This, coupled with the fact that conventional methods of oil recovery usually leave from 1 to 3 bbl of oil in the ground for every barrel produced, has aroused considerable interest in developing more efficient methods. An integral part of the mechanism of many of these new methods of recovery is a miscible fluid displacement in which oil is displaced by a much less viscous materiai such as liquid propane. A numher of irlvestigators have explored the mechanics of miscible fluid displace-ment,'.2.1.'."." but in the experiments reported many of the important factors have been varied only over a limited range far removed from norma1 oilfield values. This paper presents the results of an experimental study of oil displacement by liquid propane at field rates from linear, natural-sandstone models of various sizes. Both horizontal and vertical flow tests were made. EXPERIMENTAL APPARATUS AND PROCEDURE Refined oils with viscosities varying over a wide range were displaced at several rates by liquid Propane from both horizontal and vertical flow systems. The behavior of the displacement was observed by propane-oil analyses of the effluent and, when possible, by differential pressure measurements along the cores. A schematic flow diagram of the apParatus used to conduct the experirents is shown in Fig. 1. The cores used in the tests were 9-ft lengths cut from natural consolidated sandstone and turned to the desired diameter. These were cast in steel tubing with a low melting point (160°F) alloy which expands on solidification. Flanges welded to the ends of the steel pipes permitted sealing the ends or butting one core to another. Pressure seals were maintained with O-rings. The cores were cleaned by flushing

By Samuel Storchheim

IT was noted that variations existed in the magnetic properties, namely, coercive force, He, and rema-nence, Br, of 18/8 stainless steel wires of the same analysis when these wires were given the same percentage of reductiori of area at different rates of reduction. In order to determine the extent of these variations, a program was initiated whereby commercial 302 and 304 stainless steels were drawn with a wide variation of speeds. Ultimate tensile strengths and specific resistances, as well as the Hc-BT measurements, were determined. If variations of considerable magnitude were found, it was thought that the knowledge accrued from the investigation could probably aid in determining the particular drawing speed required to obtain desired properties for a given specification for a particular analysis of wire. Drawing Procedure Two specimens (set I, No. 302 and No. 304), the chemical analyses of which are given in Table I, were drawn at different speeds, namely, 45 to 3900 ft per min, directly from 0.016 in. diam wire to 0.004 in. diam wire, a 93.7 pct reduction of area. To obtain this high percentage of reduction, the wire at 0.016 in. was softened by annealing at 1150°C. It was then strung in a No. 16CF variable speed Vaughn drawing unit and passed through 13 B.&S. gage dies of successively smaller diameter, as shown in the accompanying table. Following this step, several hundred feet of the wire was drawn, at a particular speed, through the dies and wound upon a spool. Once the sample of wire was drawn at the desired speed, the spool with the finished sample was removed, tagged for later identification, and an empty spool was placed in the machine. Another wire sample was drawn at a different speed, after making the necessary adjustments upon the Vaughn unit. At the greater speeds, several thousand feet of sample were drawn to insure that the wire to be used for testing would be uniform. This was done because the desired speed was not reached instantly; the wire taking a short while to attain the required drawing rate. All speed measurements were made by placing a tachometer against one of the machine's pulleys during the actual drawing of the specimens. 84.4 pct reduction of area. The 0.072 in. diameter wire was also annealed at 1150°C. The process of obtaining samples was the same as described above. The only difference between the two was that the rates involved were not as extensive, set II covering a range of 625 to 1150 ft per min. Tensile tests were carried out for the 0.004 in. diam wires on a horizontal Scott Tensile Tester, while tensile tests for the 0.028 in. diam wires were made on a vertical Scott Tensile Tester. Each value listed in the tables represented the average of five samples with a maximum deviation of approximately 3 pct among the samples. Resistance per foot of the wires was determined by use of standard bridges accurate to the nearest hundreth of an ohm for the 0.004 in. wire, and to the nearest thousandth of an ohm for the 0.028 in. wire. The resistances per foot were then converted to resistivities by use of the following equation: P = RxCM where R is the resistance per ft in ohms per ft; CM, the area in circular mils; and P, the resistivity in ohms—CM. The values listed in the tables likewise

Jan 1, 1952

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent papers on interface energies in metals¹,² the concept of an equilibrium of forces has been used in the measurement of interfacial tensions. Mathematically the equilibrium of three forces is given by the relations: where the 2&apos;s are the interfacial tensions (interface energies per unit area of interface) of three phases or grains meeting at angles 21 22 and 23 (212 relates to the 1-2 boundary formed by grains 1 and 2;223 to the 2-3 boundary, etc.). If these relationships are valid, one can calculate relative values of the interface energies from measured boundary angles on specimens which have been brought to equilibrium. Since Eq 1 may be derived through a mathematical process of minimizing the grain boundary energy under the restriction that the ?&apos;s be independent of boundary orientation: the concepts of surface tensions and equilibrium of forces are not particularly essential. To deal with the general case involving dependence of boundary energy on boundary orientation, it becomes desirable to drop certain concepts formerly held (namely that energy per unit area is identical with force per unit length or surface tension) and to use the energy concept alone. It is appropriate, therefore, to use E in place of ? in deriving and using the more general equations that express the anisotropic nature of the grain boundary energy. Herring3# &apos; recently has derived the required general equations using the principle of minimization of energy. Specifying the boundary orientations in terms of angles (4) measured with reference to crystal axes within the grains, Herring&apos;s equations take the form E23 + E21 cos?8 + E12 cos?2 — sin ?12 + sin?2-?E12/?12 =O [2] where the partial derivatives are measured in the direction of counterclockwise rotation of the boundaries. Eq 2 implies that an infinitesimal displacement of the triple point along the 2-3 boundary produces no change in the boundary energy. Similar equations apply for infinitesimal displacements along each of the other two boundaries. From such equations Herring obtains the following general relationship (1 + E1 E2) sin?8 + (E2 — E1) cos?3 ________ E38______________ = (1+ E2 E8) sin ?1+ (E3— E2) cos ?1 __________^5____________[3] (1 + E sin ?2, + (E1 — E8,) COS ?2 1 E28 where E1 = 1/E23- E25 and PC and c8 have similar expressions. It is apparent that Eq 3 reduces to Eq 1 when the c&apos;s vanish. Eq 3 also reduces to Eq 1 when the E&apos;S are all equal. Shockley and Read&apos; have pointed out one limitation to these equations. When E plotted versus 4 appears as an energy cusp, as their theory requires, for example, for the energy near a twin boundary position, then Eq 3 (and therefore Eq 1 also) no longer applies if one boundary is in the minimum energy position. One of the equations of form Eq 2, however, applies if the infinitesimal displacement is along the boundary associated with the energy cusp. From the foregoing treatment it will be apparent that equilibrium angles alone are not sufficient in general for calculating relative interface energies.

Jan 1, 1951

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.&apos; As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.&apos; Other investigators have also studied the binary systems Ti-Cr,3-7&apos; Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a&apos;. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By F. H. Ellinger

TI HE crystal structure of neodymium has been re-A ported by Quill1 and by Klemm and Bommer"s to be hexagonal-close-packed, Strukturbericht-type A3, with a, = 3.650.4, c, = 5.890.4, c/a = 1.614. Klemm and Bommer,% owever, pointed out that the observed intensities of the lines of the neodymium powder pattern agreed only in part with the intensities calculated for the type A3 structure, and that the neodymium powder pattern showed extra lines which could not be traced to impurities. They found that these extra lines could be accounted for by doubling the c-axis, but apparently they did not consider their evidence to be sufficiently conclusive to justify reporting the doubled c-axis. In the present work, the structure of neodymium was found to be double hexagonal-close-packed. The neodymium metal used in the present investigation was obtained through the courtesy of F. H. Spedding of the Ames Laboratory. Its major impurity was stated to be 0.03 pct Ca. The author&apos;s spectrographic analysis indicated high purity and carbon was determined to be less than 30 ppm. X-ray powder specimens were prepared from filings stress relieved in vacuum at 200°C for 50 hr. Powder photographs were taken in an 114.6 mm diam camera (Straumanis film mounting) at room temperature and in a 19 cm diam Unicam high temperature camera at elevated temperatures. Copper x-radia-tion was used for all the photographs. The powder pattern of neodymium was found to index to a hexagonal unit cell with dimensions, as determined from the high angle Ka doublets, of: a.= 3.655+0.001.4; c, = 11.796+0.004.4; and c/a = 3.227 at room temperature. The measured density of neodymium shows that this cell contains 4 atoms, the calculated density is accordingly D, = 7.02 g per cu cm. The diffraction data for the first 15 lines of the powder pattern are listed in Table I. In a double hexagonal-close-packed unit cell, the 4 atoms would be in the positions (0,0,0), (0,0,%), (1/3, 2/3, 1/4), and (2/3,1/3,%) of space group P 6,/mmc. On the basis of these positions, the relative intensities of the reflections were calculated using the expression: 1+cos2 20 I oc \Frp 1 &apos; sin2 0 cos 0 where F is the structure factor and p is the multi- plicity factor. Since absorption was not taken into consideration, comparison of observed and calculated intensities should be made only for neighboring reflections. Each atom has 12 neighbors, 6 in the basal plane at a distance of 3.655.4 and 3 above and 3 below at the closer distance of 3.626.4. These distances correspond to an average radius of the neodymium atom of 1.820.4. The description of this structure in terms of A, B, and C close-packed layers of atoms is ABAC ABAC. ...... The structure repeats every fourth layer and the stacking sequence of the second, third, and fourth layers corresponds to cubic-close-packing of atoms. A series of powder photographs taken at successively increasing temperatures up to 680a10"C revealed that the double hexagonal-close-packed structure is stable up to this temperature. Acknowledgments The authw wishes to thank W. H. Zachariasen and A. S. Coffinberry for their helpful comments on this work and also Marion Gibbs for measuring the diffraction films. This work was sponsored by the United States Atomic Energy Commission.

Jan 1, 1956

By F. M. Lewis, E. C. Johnson

Used as a classifier in a plant expanding capacity or changing to closed-circuit operation, the liquid-solid cyclone offers the advantage of being adaptable to existing conditions. This paper presents the costs involved and experience gained from operating a unit of this kind. BY now application of the liquid-solid cyclone to various classification problems in the chemical and metallurgical fields is more or less familiar. A less publicized application receiving wider consideration as time goes on is its use as a classifier in closed-circuit grinding operations. This paper presents the costs involved and the experience gained from operating a unit of this kind. In May 1951 the Tennessee Copper Co. installed in its London mill at Copperhill, Tenn., a liquid-solid cyclone in closed circuit with a 6x12-ft ball mill. The circuit in which this cyclone is used is the regrind or secondary grinding circuit of a copper flotation plant. Originally it consisted of a 7x1-ft conical ball mill in closed circuit with a bowl classifier. Changes made in the primary grinding circuit of the mill necessitated a regrind circuit of greater capacity. The bulk concentrate to be ground was raised from 900 or 1000 tpd to 1200 or 1300 tpd, and to accommodate this increase a 6x12-ft ball mill which had been in the primary grinding circuit was moved into the regrind circuit. When this was done it was found that the classifier was too small to give efficient operation. Space in the plant was at a premium, and since use of the cyclone offered considerable economy the installation shown in Figs. 1-3 was made. The unit installed is a 24-in. diam cyclone classifier with a 20" cone angle. Diameter of the vortex finder is 8 in., the feed entrance area 20 sq. in. Maximum diameter of the adjustable apex valve is 6 in. and minimum diameter approximately 3.5 in. To refer again to Figs. 1 and 2, the cyclone* is mounted motor. It is charged with 18 tons of 1-in. balls. The overflow, or fines, passes by gravity directly to the copper flotation plant. The ball mill discharge and the new feed combine in a sump from which they are sent to the cone by an 8x6 SRL pump at a rate of 497 gpm. Pressure at the cyclone is 5 psi. For reasons dictated by the nature of the ore treated, particularly the bonding of fine grains of chalcopyrite to pyrrhotite, the froth from the second cell of the copper rougher circuit is returned to the regrind mill. This flow, which somewhat complicates the standard closed-circuit calculation, is seen in Fig. 1 to be 156 tpd of solids. This combines with the cyclone classifier underflow to constitute the ball mill feed. The requirement of the regrind product is that it be 77 to 80 pct —200 mesh. The liquid-solids cyclone operating in conjunction with the 6x12-ft mill adequately met this requirement. Of primary importance is the fact that this arrangement provided sufficient classification capacity to replace the undersized classifier and was capable of building up a circulating load to 87 pct, large enough to give an efficient grind. In this instance the circulating load is taken as the ratio of sands to new feed. Any comparison of performance between this liquid-solid cyclone and the replaced classifier would of course be unfair, since the bowl classifier was

Jan 1, 1955

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation&apos;s mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By AIME AIME

NOT a few physical metallurgists started their profession- al careers as chemists or physicists, only to surrender later to the attractions of metallurgy. The present Institute of Metals Chairman varied this more usual sequence in hat his first love was electrical engineering, when as a recent graduate he served on the staff of the General Electric Co., of Schenectady. Soon turning to metallurgy as a more interesting field, he was metallurgist and then chief engineer of the Wads- worth Watch Case Co. from 1920 to 1927. Since 1927 he has been with the International Nickel Co. at the Bayonne, N. J., research laboratories where he is staff adviser.

Jan 1, 1940

By R. C. Mahon

Operators concerned with the destruction of their piping by acid mine waters will be interested in the method by which this problem was solved at the Cardiff mine of the Homer group. Rubber lined, or acid resisting metal pipes were found too expensive. Casting concrete lining in pipe would have required a minimum thickness of one inch, thus excessively reducing the pipe&apos;s diameter, as well as taking twenty four hours per length of pipe. The Naylor Pipe Co. of Chicago, having experimented with centrifugal lining of pipe with concrete, provided information which eventually solved the problem. An experimental plant was constructed as shown, and the following procedure developed : (1) Kerosene is used to remove the interior oil coating of new pipe. Closed with blank flanges, the pipe is revolved for eight minutes at varying speeds. Stopping and starting the motor achieves a good washing action. The kerosene is then drained off, and similar washing action with caustic soda removes any excess. Swabbing in done with burlap fastened to a 1/2-in. pipe. (2) The aggregate, made of one. part quick-setting cement and two

Jan 1, 1949