Search Documents

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967

By H. P. Stuwe

It is investigated whether a model of sphere packing permits the computation of the lattice parameters and their variation with concentration in various a phases; it does, except in phases containing silicon. Several observations indicate that a particular role is played by the "E-atoms" in the lattice. THE phase is formed by many alloys of the transition elements.'-' Its structure has been described by Bergman and Shoemaker,5,8 Dickins, Douglas, and Taylor,7 and Kasper, Decker, and elanger.' There are five kinds of crystallographically equivalent positions for the 30 atoms in the unit cell which have been designated by these authors I, 11, 111, IV, and V or, in the same sequence, A, B, C,D, and E, as shown in Fig, 1. For the purposes of the present paper two elements of the lattice will be discussed separately: The lattice planes perpendicular to the c-axis which are made up by the atoms A, B, C, and D and which determine the a-parameter; and the close-packed "vertical rows" of E-atoms which determine the c-parameter. asper,9 and Frank and kasper10 described the a phase and other complex structures as sphere packings. In these papers particular attention is paid to the coordination polyhedra. Lattice positions with an equal number of nearest neighbors are considered equivalent regardless of their crystallo-graphic description. This seems to work very well for the explanation of ordering phenomena in the a phase as far as information on this is available." If the description of the phase as a sphere packing is valid it should be possible to draw two further conclusions: 1) It should be possible to calculate the lattice parameters from the atomic radii of the components, and 2) It should be possible to predict the variation of the lattice parameters with concentration within one phase field. Both points are discussed in this paper. PROCEDURE Measurements of lattice constants were done with a symmetrical back-reflection X-ray camera. With Cr-radiation, about a dozen a1 lines could be observed with most samples. From the (550/710)- and 720-lines the a-value was computed. With this value the c-parameter was calculated from the (333)- and (413)-lines. Finally, the position of all the other lines was computed from the lattice parameters thus obtained. In this way the validity of the indexing could be checked and, at the same time, this proce- dure gave an estimate of the accuracy of the lattice parameters. A correction was made for film shrinkage. The atomic radii used in the computations are the Goldschmidt radii for coordination number 12. Actually, some of the atoms have a coordination number of 14 or 15, but the error thereby introduced is small. * For the computation of lattice constants from the atomic radii an "average atomic radius" of all components was used, i.e., complete disorder was assumed. Although this seems to be true for some systems like OS-Cr,4 it is not true in others.11,13,14 The ordering model, however, which has been suggested by Kasper on the basis of extensive research lets both kinds of atoms contribute to both the ''vertical rows" and the lattice planes perpendicular to them, so that even with ordering of this kind the assumption of complete disorder cannot introduce a very serious error in calculating lattice parameters. RESULTS Bergman and shoemaker6 gave a table of the interatomic distances in the Fe-Cr phase. If we disre-

Jan 1, 1960

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By Tell Ertl

The term oil shale is defined. Foreign oil-shale developments are outlined briefly. The richest and most extensive oil-shale deposits in the United States lie in western Colorado. The Bureau of Mines is opening two adjacent areas for underground mining. in western Colorado. From the first area the oil shale is mined selectively as required by the retorting plant. The second area is being developed as a unit of a full scale oil-shale mine to ascertain the most practical methods of mining oil shale and to determine costs. In both of these mining areas, research will be carried on to develop new and improved practices for mining oil shale. Introduction Oil shale is a sedimentary rock containing a solid mineraloid of indefinite composition known as kerogen. On heating oil shale, the kerogen undergoes thermal decomposition and some of the vapor products of the decomposition can be condensed as shale oil. Oil from shale can be a major source of liquid fuels since extensive deposits of oil shale are known to exist throughout the world. The United States considers the establishment of an oil-shale industry only when doubt exists of the adequacy of the domestic supply of crude petroleum. On the other hand, oil shale is not strange to foreign oil men. The industry is an old one in other parts of the world. The French industry has been in existence since 1838, the Scottish since 1859, the Australian since 1860, the Estonian and Swedish The since World War 1, and the Manchurian industry since 1929. The most highly exploited oil-shale deposits are the Carboniferous shales of Scotland. About 20 seams ranging from 4 to I2 ft in thickness are worked. The yield during recent years in scotland has been 18 to 25 gal of shale oil per ton, from 3&"30'000 tons per year' The French and Swedish oil-shale deposits are of lower grade than the Scottish. The Estonian oil-shale deposits are 7 ft thick, and the oil yield averages 50 gal per ton. Over 1,000,-ooo tons are mined each year, half of which is used directly as fuel to substitute for coal and the other half is used for the production of oil. Immense deposits of oil shale that will yield 10 to 15 gal per ton exist in Germany. Because of the impending loss of the Rumanian and Polish oil fields and the bombing of synthetic liquid fuel plants, the Nazis in 1943 started a large-scale oil-shale program in Germany. By V-E Day, it is said, oil-shale production had reached the rate of 2500 tons per day and rapid expansion of the industry was imminent. Australian oil shale, known as torbanite, occurs in beds 2 to 6 ft thick. It is of a very high grade and on retorting yields 80 to 160 gal per ton. The oil-shale industry of Manchuria was the largest in the world during the past decade. The well-known Fushun coal deposit in Manchuria has an overburden of 500 million tons of oil shale about 450 ft thick that will yield 10 to 15 gal of shale oil per ton. The oil shale is

Jan 1, 1949

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By S. Feuerstein

THE influence of environment on the mechanical properties of metals has been extensively studied and documented.' Most investigations have dealt with an interaction between a particular environment and a specific metal surface and the concomitant change in bulk mechanical behavior. Typical contributing media are oxide and metal film:;, electrolytes, and other surface-active agents. In the last category fall controlled gaseous environs (i.e., pressure or vacuum). Most vacuum exposure experiments prior to 1963 were conducted at pressures s>10-6 torr and elevated temperatures, or in such a manner as to prolong the exposure (e.g., by stress-rupture, creep, and fatigue). Little attention has been given to vacuum environment effects on the mechanical behavior of metals subjected to simple uniaxial deformation at room temperature. Test times and temperatures were assumed too ineffective as far as bulk changes were concerned. Further, the contribution of surface effects to the bulk mechanical behavior of metals was considered minimal. Under vacuums of the order of 1.0- 8torr and higher, molecular densities and, consequently, the rate of monolayer formation are such that exposures from seconds to days would be required for complete gas coverage. Thus, atomically clean surfaces created under ultra-high vacuum could conceivably maintain their cleanliness for time intervals orders of magnitude greater than at higher pressures. The influence of this unusual type of environmental surface phenomenon on the short-term bulk mechanical behavior of aluminum was first observed by Krame and Podlaseck in 1963.' kin equivalent effect was reported for magnesium by Williams and Nelson.3 It was concluded from these studies2,3 that vacuum and, consequently, the monolayer formation rate of the oxide, were responsible for the described changes in flow behavior. The presence of an oxide layer impedes dis- I) EXPERIMENTAL DATA: MOLYBDENUM The tensile behavior of molybdenum was investigated by the author4-6 at ambient temperature over a range of pressures from 760 to 10-10 torr. These studies revealed that the flow behavior of the bulk specimens (0.200 in. diam by 2 in. gage length) was independent of pressure on sintered (0.062 mm grain size) and arc-cast polycrystals (0.012 to 0.149 mm grain sizes) and single crystals. Since the specimens were relatively large in size, it was assumed that any flow behavior effect would be surface-limited because of the short-term deformation procedure. Strain-rate-change experiments performed to determine the activation volumes for individual specimens at 760 to 10- 10 torr further indicated that the surface flow contribution was either minimal or zero, contrary to the findings of Shen el a1.7 on aluminum. Although the flow behaviors did not change, specimen ductility did change. For the sintered material at a strain rate of 4.2 x 10-4, specimen ductility was -9 pct higher at l0- 10 torr than at atmospheric pressure (dry nitrogen). A more comprehensive investigations on this same material revealed a distinct pressure dependence, Fig. 1. Intermediate and atmospheric pressure tests were obtained by backfilling the system from l0- 10 torr with extra dry, prepurified nitrogen. Other environments (air and purified argon) were also utilized for the 760 torr experiments; the results were essentially the same as those for dry nitrogen atmospheres. Departure from the fracture strain values obtained at 760 torr takes place in the vicinity of l0-6 torr, as indicated by the scatter band; a noticeable ductility increase is apparent at l0-8 and 10-10 torr.

Jan 1, 1970

By J. Geertsma

In order to obtain a better insight into the pressure-volume relationship of reservoir rocks a theory of pore and rock bulk volume variations is presented. The theory is independent of the shape of the pores but is restricted to isotropic porous media built up of continuous homogeneous matrix material. The main conclusion obtained from this theory is that only three elastic constants and three viscous constants are required for describing pore and rock bulk volume variations if the porosity is explicitly introduced into the treatment. In addition, reasonable approximations are introduced for various types of reservoir rock, e.g., sandstones, limestones, and shales, which lead to further simplifications of the basic formulas. In consequence there is then a further reduction in the number of deformation constants which have to be determined experimentally. It is shown how measurements of these remaining deformation constants can be performed most conveniently. Finally the application of the theory to reservoir studies is discussed and the translation of experimental results obtained in the laboratory into reservoir behavior is considered. INTRODUCTION The decline of fluid pressure in connection with the withdrawal of fluid from an underground reservoir gives rise to a change in volume of both reservoir fluids and reservoir rock. The volume variation of the reservoir rock results in a decrease of both the pore volume and the total volume of the fluid-filled formation. Whereas the variation in volume of the reservoir fluids with pressure is usually known from PVT analysis, that in the volume of the porous medium is rarely measured, as it is considered of minor importance in reservoir engineering. Nevertheless, certain experimental results' suggest that in a number of cases the neglection of the variation in pore volume may introduce errors into material balance calculations of reservoirs producing above the bubble point. Only a few experimental results on the compressibility of porous rocks have been published. The compressibility of pure quartz and of calcite can be found in a paper by Adams and Williamson'. Botset and Reed' carried out some experiments on the compressibility of loose sands, while Carpenter and Spencer' measured the compressibility of a number of consolidated sandstones, which data were supplemented by Hughes and Cooke5. Hall' finally reported a number of experiments designed to study the influence of the porosity on the compressibility of oil-bearing formations, from which it appeared that, particularly in the low porosity range, the compressibility of the pore volume is important enough to be taken into account. Difficulties, however, arise in applying these experimental results to field cases. This is partly due to the fragmentary nature of the published data. Yet even if more complete data were available, the need for a theoretical background would be strongly felt. Such a background can be partially found in studies carried out by Biot,6,7 who published a theory of elastic deformations of porous materials and their influence on fluid displacement within the pores, by Lubinski8, who studied the stress distribution in an elastic porous medium neglecting pore compressibility, and by Gass-mann" who mathematically analysed the elasticity of packings of spheres. The contributions of Biot intro-duce a number of deformation constants which are impractical for reservoir rocks from an aspect of experi-mental determination. The theory developed by dass-mann is correct but difficult to read. It appeared, how-

Jan 1, 1958

By Ralph E. Esarey, Robert G. Reno

DriLLing activity and prospecting for oil and gas increascd in Indiana in 1941 over the previous year. The greater part of the drilling and development continued to centralize in the Indiana portion of the Interior Coal Basin, in the southwestern part of the state, but other parts of the state were not neglected. Many wildcat wells were drilled, including a series of core tests through the mantle of drift on the southern flank of the Michigan Basin. These core tests have been followed by several unsuccessful production tests. Production tests were made also along the axis of the Logansport-Kankakec branch of the Cincinnati Arch. In all, 411 field locations and 141 wildcat wells were completed in Indiana during 1941; that is, a total of 552 wells, an increase of 3 2 wells over the previous year. The field tests resulted in 260 oil wells, 57 gas wells, and 94 dry holes; wildcats included 16 oil wells, 3 gas wells and 122 dry holes. At the end of the year, 53 field wells and 34 wildcats were drilling. Gibson and Posey Counties led the state, with 154 and 155 wells drilled, respectively. However, 125 wells produced oil in Gibson County, while 98 produced oil in Posey County. Twenty-five per cent of all wells drilled were wildcat; II per cent of these produced oil and 5 per cent produced gas. Grifin field continued to lead in drilling activity, with 157 successful wells and 20 dry holes (including important wells defining the field). Production is found in five pay zones (Tar Springs, Waltersburg, Elwren, Aux Vases and McClosky). It produced a major part of Indiana's estimated 7,200,000 bbl. of oil during the year. Heusler field, Posey County, expanded with 11 oil ells and 4 dry holes in the Waltersburg and Tar Springs. Vienna field, Posey County, completed four oil producers in the Mansfield sandstone, between 1200 and 1250 ft. The College field, discovered late in 1940, received three oil producers and two dry holes in the Aux Vases. Two new fields were discovered in Posey County during the year: Lamott pool, in the Tar Springs, at 1950 ft., had initial production of 55 bbl. on discovery. One producer and one dry hole have been drilled since. Mt. Vernon pool found saturation in both the Waltersburg and Cypress formations. The discovery well tested about 1000 bbl. per day; it tested the McClosky at 2764 ft. Seven producers have been drilled since the October discovery. Welborne-Switch pool found oil in the Cypress sand at approximately 2500 ft., with an initial production of 33 bbl. One more well in the area proved a dry hole. Gibson County had the following discoveries in 1941: The Patoka field was opened by a McClosky producer of 300 bbl. Another producing well has been drilled. An attempt was made to extend the Illinois Mt. Carmel field into Gibson County, Ind., and one producer of 24 bbl, was completed on the Indiana side. A dry hole has since been drilled, one location south. One small well was completed in the Mans. field at 1105 ft. in sec. 31, T.2 S., R.12 W., Gibson County promising a new field

Jan 1, 1942

By Robert G. Reno, Ralph E. Esarey

DriLLing activity and prospecting for oil and gas increascd in Indiana in 1941 over the previous year. The greater part of the drilling and development continued to centralize in the Indiana portion of the Interior Coal Basin, in the southwestern part of the state, but other parts of the state were not neglected. Many wildcat wells were drilled, including a series of core tests through the mantle of drift on the southern flank of the Michigan Basin. These core tests have been followed by several unsuccessful production tests. Production tests were made also along the axis of the Logansport-Kankakec branch of the Cincinnati Arch. In all, 411 field locations and 141 wildcat wells were completed in Indiana during 1941; that is, a total of 552 wells, an increase of 3 2 wells over the previous year. The field tests resulted in 260 oil wells, 57 gas wells, and 94 dry holes; wildcats included 16 oil wells, 3 gas wells and 122 dry holes. At the end of the year, 53 field wells and 34 wildcats were drilling. Gibson and Posey Counties led the state, with 154 and 155 wells drilled, respectively. However, 125 wells produced oil in Gibson County, while 98 produced oil in Posey County. Twenty-five per cent of all wells drilled were wildcat; II per cent of these produced oil and 5 per cent produced gas. Grifin field continued to lead in drilling activity, with 157 successful wells and 20 dry holes (including important wells defining the field). Production is found in five pay zones (Tar Springs, Waltersburg, Elwren, Aux Vases and McClosky). It produced a major part of Indiana's estimated 7,200,000 bbl. of oil during the year. Heusler field, Posey County, expanded with 11 oil ells and 4 dry holes in the Waltersburg and Tar Springs. Vienna field, Posey County, completed four oil producers in the Mansfield sandstone, between 1200 and 1250 ft. The College field, discovered late in 1940, received three oil producers and two dry holes in the Aux Vases. Two new fields were discovered in Posey County during the year: Lamott pool, in the Tar Springs, at 1950 ft., had initial production of 55 bbl. on discovery. One producer and one dry hole have been drilled since. Mt. Vernon pool found saturation in both the Waltersburg and Cypress formations. The discovery well tested about 1000 bbl. per day; it tested the McClosky at 2764 ft. Seven producers have been drilled since the October discovery. Welborne-Switch pool found oil in the Cypress sand at approximately 2500 ft., with an initial production of 33 bbl. One more well in the area proved a dry hole. Gibson County had the following discoveries in 1941: The Patoka field was opened by a McClosky producer of 300 bbl. Another producing well has been drilled. An attempt was made to extend the Illinois Mt. Carmel field into Gibson County, Ind., and one producer of 24 bbl, was completed on the Indiana side. A dry hole has since been drilled, one location south. One small well was completed in the Mans. field at 1105 ft. in sec. 31, T.2 S., R.12 W., Gibson County promising a new field

Jan 1, 1942

By W. L. Kerlie, J. H. Richards

The variation in hydrogen content of basic open-hearth steels during refining and the effect of changing from steam to air atomization were studied. The water content of the furnace atmosphere, the slag basicity, and the degree of oxidation of the slag-metal system largely control the hydrogen in the steel. SMALL amounts of hydrogen have an adverse effect on the ductility of steel and a wide range of hydrogen contents has an adverse effect on the internal soundness of both ferrous and nonferrous castings. This has been of major concern to the metal industry, both manufacturers and fabricators, for many years. As one of the results of continuing investigations of the hydrogen problem, much has been learned about methods of reducing the hydrogen content of liquid metals below the relatively high levels that are normally associated with such phenomena as rising ingots and excessive porosity in sand casting. However, it was not until a reliable and simple method for sampling and analyzing liquid metal was developed that much progress was possible in quantitatively evaluating the effect of steelmaking practice on hydrogen contents at levels below 6 to 8 ppm. Throughout all the work described in the following presentation the Geffner pintube technique was used to obtain samples of liquid metal1 * and the tin-fusion method, developed at Massachusetts Institute of Technology,2 was used to analyze the samples. Before attempting a systematic experimental program for minimizing the hydrogen content of open-hearth steels, it was necessary to determine the variation in hydrogen in the open-hearth bath during the normal processing of a heat. The logs of ten heats are illustrated in Figs. 1 through 7. The number at each point on the graphs refers to the number of pintube samples analyzed for hydrogen. An increase in the hydrogen content of the liquid metal during the early period of refining is apparent in all heats. There is evidence of a decrease in hydrogen later in the refining period, see Fig. 2, for example. Therefore, the existence of a maximum hydrogen content at some intermediate time during the refining period is anticipated. To test for the existence of a maximum, the data illustrated in Figs. 1 to 5 were grouped together so that they could be examined on a collectively comparable basis. The grouping was effected, as illustrated in Fig. 8, by superimposing Figs. 1 to 5 so that the apparent hydrogen maxima coincided at a fixed position, indicated by the zero on the time axis. Also, by vertical adjustment until the graphs appeared to the eye to be superimposed, the hydrogen scale was made to show the change in hydrogen content. That is, a standard amount was subtracted from the hydrogen values for each heat. Therefore, Fig. 8 represents a generalized presentation of the data and, for this reason, cannot be used to predict the actual hydrogen content of the bath during refining, but rather to show the probable rate of change in hydrogen during refining. Statistical examination of the grouped data in Fi.g. 8 shows that the apparent. increase and suhsequent decrease in hydrogen are real and confirms the existence of a maximum in general. The average increase In hydrogen during the early period of refining is between 0.8 and 1.3 ppm per hr, and the

Jan 1, 1958

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By D. R. Parrish, W. E. Lamoreaux, W. W. Owens

Several methods are now being used by the industry for determining the gas-oil flow characteristics of reservoir rock samples. Most of the laboratory experirnerltal rlzethods can be classified either as steady-state, unsteady-state, or Hassler-type tests. Although the validity of the results obtained by any specific method is not questiorzed, in general, the complexity of these methods leaves much to be desired. This investigation dealt primarily with the development of a simplified unsteady-state (gas drive) laboratory test method for measuring kg/ko re1ationships of small core samples. A procedure for selecting uniform and representative sandstone rock samples was developetl since it was observed that the reliability of the test resu1ts was dependent upon having a sample which was uniform in porosity and permeability. The importance of factors known to influence the results of this type test, such as oil viscosity, gas expansion, and pressure differential were eva/uated. The method of calculating the test results was found to give valid data over a wide range of gas expansion. The limits of pressure differential and oil viscosity which would insure reliable results were defined. In cornparisorz with other presently used testing methods, the gar drive method requires considerably less apparatus, is less time consuming, and is more readily adaptable to a routine type core test. INTRODUCTION The detcrmination of the gas-oil flow characteristics of reservoir rocks has been given concentrated study by the oil industry for the past decade. Both analytical and experimental methods have been considered. The analytical methods have generally relied on a simplified characterization of porous materials in order that the fundamental laws of fluid flow and capillarity could be utilized. More direct experimental methods have been proposed by numerous production research laboratories with the primary goal being a simple and inexpensive, yet reliable method for measuring the gas-oil flow characteristics of reservoir rock samples. The experimental methods which have been reported in the literature generally can be grouped into one of the following classifications: 1. Steady state1,2,3,4 in which a fixed ratio of flowing fluids is forced through the test sample until equilibrium conditions of saturation and pressure gradient are established. 2. Hassler or stationary liquid method5,6,7 in which a uniform liquid saturation is attained, usually through capillary desaturation, then gas or oil is flowed through the sample at a pressure drop insufficient to disturb the pre-established saturation. :. Non-steady state method1,8,9,10 In which only the gas phase is injected into the sample, causing displacement of the oil phase and resulting in a system of continually changing average saturation and saturation gradient. The steady-state and Hassler methods have been most popular because, no doubt, of the simplicity of the actual relative permeability calculations. The problems involved in these methods were limited to apparatus design and measurement techniques. In the steady-state method, for instance, a constant flowing fluid ratio is established which, at equilibrium, results in an essentially uniform saturation over the entire length of the test sample. Therefore, the basic flow characteristics could be obtained by correlating the average saturation of the test sample with the kg/ko determined at various flowing gas-oil ratios.

Jan 1, 1957

air-lift and equipped with tapered tubing of proper design, we would have a gas input consumption of about 2500 cu. ft. per bbl., which at 3 to 4c. per 1000 cu. ft. would be 7 1/2 to l0c, per bbl., and there would be very infrequent loss of production due to stoppages. It has been demonstrated that with efficient design of air-gas lift, the production of wells can be increased much beyond that obtained with the former type of air-lift employed; also that small wells can be operated by air-lift with tapered tubing at a cost that places this method in competition with beam pumps in many fields. The next step in conservation that the writer expects to have an opportunity to demonstrate is that of restoring the pressure in a pool and producing by air-gas lift all of the oil possible to lift economically. This combined operation is probably the method toward which we shall eventually be working in recovering the maximum quantity of oil from pools where the oil is recovered through bore holes. General Discussion on the Air-gas Lift H. P. Porter, Tulsa, 0kla.—The papers presented at this meeting contain a great amount of valuable information. Wonderful progress has been shown in the development of air and gas-lifts. There has been nearly everything brought out that touches upon the subject. The real point that is lacking is exact knowledge of the velocity with in the flow column which will produce the best effect—that is the thing we must know more about. Velocity in Gas-lift Flow In other lines of industry the matter of velocity of fluids in pipe lines has been well analyzed and there are known laws by which to calculate velocity of flow; for instance, in irrigation work large pumps are designed with intake pipos to employ an intake velocity of 4 ft. per scc. By reduced cross-sect'ion the velocity is increased rapidly as it enters the pump and the discharge rate is at 12 ft. per src., which in turn is reduced in the discharge column to 4 ft. per sec. Crushed coal, grain and granular material is found to be best conveyed by air when a pneumatic conveyor is employed at 100 ft. per sec. As in the design of a pumping plant or a pneumatic conveyor, the velocity at the lower end of the column in the flowing well must be controlled within certain limits for best results. Mr. Griswold, I believe, stated that they had velocity as low as 15 it. per scc. and from that up to 78 ft. per sec. Mr. Pierce and Mr. Lewis showed an ideal flow column showing how the velocity increased as the fluid was carried up the column, hut did not give any figures as to the velocity. It would be well to take that sort of a diagram to establish an ideal velocity at the lower or intake end, and then calculate the velocity from expansion of the gas as it goes up. It may be that the, ideal intake velocity would vary, depending on the depth of the well, the quantity of liquid to be handled or the pressure which it may be desired to hold. The subject is one that might be worth much research.

Jan 1, 1928

By D. A. Thomas, E. S. Meieran

Tungsten wires were examined by transmission electron microscopy after drawing and after high-temperature annealing. Drawn wire consists of highly elongated grains called fibers, whose long axis is parallel to [110]. Each fiber is ribbon-shaped, with the wide dimension of the ribbon parallel to (001) and the narrow dimension parallel to (110). Furthermore, most fibers are bent about [I10] and twisted along their length. The fibers are divided into cells, which in some cases contain a platelet substructure lying on (110) planes. The misorien-tations of these platelets accumulate to allow the macroscopic twist of the fibers. During annealing, several competing reactions occur, starting at different temperatures and progressing at different rates. Among these processes are fiber-boz~ndary migration, polygonization, dislocation rearrangement, and possibly impurity segregation. The fiber-boundary migration accompanied by the formation of transverse boundaries during polygonization leads to an equiaxed grain structure although recrystal-lization does not occur. There is a relationship between the flow stress of the wires and their average subgrain width in the form sy = s0 + kyd-1/2 . Also, there appears to be a relatio'nship between wire ductility and the formation of transverse boundaries during annealing at about 800°C. THERE have been many investigations of the structures and properties of tungsten wires1-4 due to their commercial importance for use as lamp filaments. The structural studies have so far been limited to optical microscope and replica electron-microscope studies. due to the difficulty of .-me- paring from wires thin foils which can be examined by transmission electron microscopy. However, this difficulty has been recently overcome,5 and it is now possible to examine tungsten wires by transmission electron microscopy as well as by other techniques. In this paper, the structure of drawn tungsten wire is described, as are the changes in the structure during high-temperature annealing. Some discussion of the relationship between structures and properties is also given. EXPERIMENTAL MATERIALS AND PROCEDURES Commercial 0.030-in.-diam doped tungsten wires drawn at progressively decreasing temperatures between about 1400° and about 800°C were examined. The composition, mechanical properties, and optical microstructures are described in detail elsewhere.' All experimental materials were vacuum-annealed for 10 ot 30 min at temperatures at 100°C intervals between 700° and 2000°C. Specimens were thinned for examination in the Siemens Elmiskop I electron microscope by the method of Meieran and Thomas.5 STRUCTURE OF AS-DRAWN WIRE The optical microstructure of as-drawn tungsten wire has been described by Peck and Thomas.7 They observed that wire in longitudinal section consists of highly elongated grains called fibers whose width varies between 1 and 10 µ, while in transverse section the fibers appear to be elliptical in cross section and bent about their common [110] wire axis. They explained this unusual appearance as being due to the drawing of a bcc material with a [110] texture, and predicted that the wide and narrow planes of the fiber cross section would be parallel to (001) and (110), respectively. The fibers apparently bend about the [110] axis during drawing to maintain grain boundary continuity during drawing. Transmission electron microscopy offers a way of checking these predictions as well as providing a more detailed picture of the wire structure. Figs. 1, 2, and 3 are typical electron micrographs of

Jan 1, 1965

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel framework buildings started toward the end of the last century. Progressively the requirements became more stringent, crushed bank slag, weighing 80 lb per cu ft as compared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft. Geology Perlite is one of the large family of rocks originating from a granitic or acidic magma and generally has a "rhyolitic composition with a marked perlitic structure."² The name "perlite" is a derivation from "perlstein" originally given "to certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."3 The cause of the perlitic texture is somewhat controversial. Johannsen attributes the texture to strain set up in the glass by cooling and describes the finding of peculiar, glassy balls, called marekanite, more or less rounded and showing concave indentations, which may be left when perlite is broken. Frank Rutley, on the other hand, in 1881, while working on vitreous rocks from Montana, observed that there was incipient or partially started crystallization with segregation of water toward the un-crystallized portion in all specimens of perlite examined. Further he observed evidence of strain around focii of crystallization to which he ascribed the development of the spherical cracking which gives the rock its perlitic texture.4 Widespread over the western and southwestern United States where Tertiary vulcanism is exposed, perlite commonly is associated with andesitic, basaltic, and rhyolitic lavas with inter-bedded tuffs and ash of Eocene age although some deposits are associated with rocks assigned to the Pliocene age.5, 6 n nearly all cases the perlite overlies water laid tuff beds or agglomerates or breccias of explosive nature, an outstanding exception being the occurrence of perlite as the chilled selvage of andesite intrusions.7'8 Available chemical analyses of per-lites from the western and southwestern United States indicate that they are varieties of leucorhyolites rather than of normal rhyolites, leucorhyolites having less than 5 pct of dark minerals, normal rhyolites having more than 5 pct. This conforms with Johannsen's observation that leucorhyolites are the prevailing kind in North America.9 Tables 1 and 2 give

Jan 1, 1950

By J. M. Campbell, T. S. Buxton

The most widely used methods of predicting the volumetric properties of gas are based on the principle of corresponding states, which asserts that the compressibility factor is a universal function of reduced temperature and pressure. Previous studies have shown that the acentric factor, as proposed by Pitzer, l is an important addition to reduced pressure and reduced temperature as factors affecting the compressibility factor. Results of this study indicate that, if the pseudocritical temperature and pressure used to determine the reduced conditions are adequately predicted, characterization of natural gas-carbon dioxide mixtures with the acentric factor will allow reliable determination of the compressibility factor. Comparisons of predicted and experimental compressibility factors have shown that the pseudo-critical constant rules of Stewart, Burkhardt and Voo 2 are satisfactory for hydrocarbon mixtures. However, these rules fail to predict the pseduo-critical constants for hydrocarbon-carbon dioxide mixtures. Based on graphically determined pseudocritical temperatures for binary hydrocarbon-carbon dioxide mixtures, a correlation which gives the required correction to the Stewart, Burkhardt and Voo rules was prepared and a compressibility factor prediction technique was proposed. To test the proposed technique, compressibility factors for live mixtures of methane, carbon dioxide and either ethne or propane were experimentally determined at 100, 130 and 160F and pressures up to 7,026 psia. The predicted and experimental compressibility factors for these live mixtures had an average absolute deviation of 0.55 percent. INTRODUCTION Two-parameter generalized correlations based on the principle of corresponding states (PCS) are presently available for reliably predicting the compressibility factor of lean natural gas, i.e., natural gas with low concentrations of hydrocarbons heavier than methane. When these same correlations are used for mixtures of natural gas and carbon dioxide, large deviations between actual and predicted compressibility factors are observed. This study was undertaken to provide a means for accurately predicting the compressibility factor for such mixtures. In the past, two avenues of approach have been employed to extend the applicability of the PCS. The first has been to introduce additional parameters. The second has been to develop combination rules for predicting pseudocritical constants which do not suffer from the limitations of the commonly used molal average constants. In this study, both of these approaches have been considered and employed to arrive at a method for predicting the compressibility factor of mixtures of hydrocarbons and carbon dioxide. SELECTION OF A THIRD PARAMETER Failure of the original PCS to predict the compressibility factor for all pure gases, regardless of their mass, shape or polar moment, has led to the introduction of additional parameters into the PCS. Parameters have been introduced to correct for quantum deviations,3-5 non-spherical or globular shapes6-9 and for polar moments.8-12 In addition to these parameters which are based on some microscopic property and intended to correct for some specific cause of deviation, more general parameters based on some bulk property have also been introduced.1913-16 To use additional parameters to correct for each of the possible causes of deviation among the individual constituents of a gas mixture would require a rather complex form of the PCS. To maintain the PCS in as simple a form as possible, it is more desirable to have a single third parameter which is based on some bulk property influenced by several of the factors causing deviations. The third parameter selected for use in this study is a factor originally proposed by Pitzer.9

By G. G. Priest, B. E. Morgan

The production of oil and gas from wells is often seriously hindered by the compaction of solids in the perforations during the perforating process. To realize the full productive capacity of a well, it is necessary either to remove the plugging material from the perforations or to perforate in a manner which does not cause plugging of the perforations. The latter method can be accomplished by having a non-plugging fluid in the casing at the time the well is perforated. This paper describes the results of laboratory tests, perforating tests, and experimental field tests which demonstrate that certain emulsions serve effectively as non-plugging perforating fluids. The principal components of these emulsions are two liquids: an aqueous phase consisting of a solution of either sodium chloride or calcium chloride, and an oil phase consisting of diesel oil, tetrachloroethylene, or a combination of both. Small amounts of other agents which serve to stubilize the emulsions, to reduce the fluid loss, and to inhibit corrosion are also present. The density of the emulsions is controllable within the range of 7.5 to 12.5 lb/gal; no insoluble solids are present, the filtration rate is low, and the thermal stability is satisfactory at temperatures as high as 200°F. The corrosion of steel by these emulsions is negligible. Tests conducted under conditions which simulate the temperature and the pressure in an actual well demonstrate that these emulsions fulfill the requirements of a non-plugging perforating fluid. In addition, lirnited field experience furnishes evidence that these emulsions remain in position after they are spotted, that they are retained in the casing after the perforations are made, and that they are easily removed from the perforations when the well is opened for production. When the pressure in the borehole is greater than the formation pressure at the time a well is perforated, plugging of the perforations can be avoided by spotting an emulsion adjacent the interval to be perforated. This procedure should eliminate low well productivity caused by plugging the perforations. INTRODUCTION Nature of Problem The most widely used method for the completion of oil and gas wells is to set and cement casing through productive horizons, and then to obtain production by gun-perforating the section of casing opposite the desired interval. This method is gen- erally successful and it was thought at one time that those failures which did occur were due to insufficient penetration by the perforator. Despite recent improvements in perforators which assure ample penetration, unsatisfactory fluid production continues to be a problem. Evidently, the trouble comes from some other source. Recent results obtained by Allen and Worzel1 demonstrated that low fluid productivity may be caused by the perforating process and/or by the fluid in the wellbore at the time of shooting. They found that perforations are often completely plugged by debris from the perforator, pulverized sand from the formation, and compacted solids from the drilling mud when the pressure in the wellbore is greater than the pressure in the formation at the time of perforation. In some cases a differential pressure in excess of 400 psi was required to initiate flow into the well through these plugged perforations. The plugging of perforations by solids not only causes low productivity from wells, but it creates simultaneously other problems in the production of oil and gas. For example, when most of the perforations are plugged, high rates of flow must occur through the few perforations that are open. The resulting high pressure drop may cause production

Jan 1, 1958