Search Documents

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Tiago Seixas Bittencourt

Technological developments, associated with the constant worry about the environmental impacts arising from industrial activity, it has driven the development of technologies and practices for efficient fumes and particulates capture arising from the manufacturing processes of steel in steel plants in general. Currently, the electric steelshops in operation with Electric Arc Furnaces (EAF), seek parameterize/design dedusting systems able to retain most of the particulates generated during melting and refining of steel in FEA through configurations of equipment, technologies and parameters operation in order to equalize the antagonistic relationship between effective fumes capture and energy balance of the EAF. The present work gets as a fundamental premise to evaluate critically the possible different settings of the usual dust removal systems, as well as their respective classical parameterizations. The work main purpose is to establish a general rule evaluation technique for dedusting system considering the different modes of operation of an Electric Arc Furnace.

Jul 30, 2018

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Antonio Esposito

Saving energy and reducing pollution by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and updated. The most modern design tools should be adopted to maximize the coke production rate also ensuring the best coke quality. In this scenario, Paul Wurth is realizing the new coke making plant of CSPecem, Ceara - Brazil. These batteries are based on Paul Wurth “jumbo oven concept”. This solution incorporates all most modern features and design upgrading, in the aim of an easy and long-lasting operation putting a particular attention to environmental performances: the reduced number of ovens and the low number of pushing per day have the main effect of reducing pollution sources. Finally the paper will highlight Paul Wurth SOPRECO® System, which is foreseen to be installed in CSPecem batteries. SOPRECO®, which is capable of controlling the pressure for each individual oven in a coke oven battery, is thus able to reduce volatile emissions through doors, roofs and stand pipes up to 90%. The coke oven gas (COG) produced during the carbonization process is cleaned in a coke oven gas treatment plant to the level stipulated by applying the Best Available Technology (BAT).

Aug 1, 2018

By Juliano Braz Possatti, José Fagundes Júnior

This project involved a teamwork including process control, maintenance and operation specialists, R&D and CTO experts to identify and actuate on each opportunity to increase charging temperature, furnace efficiency, decrease discharging temperature when possible, decrease FM and RM cycle time (mainly speed increase and interpass time decrease), tracking zones optimization, safe use of equipment power limits, safety interlocks revision and tune models for Mill Pacing Control and Slab Design.As result of these efforts, ArcelorMittal Tubarão HSM today occupies a prominent position among the best HSM of similar layout and produced mix of the group and worldwide. This paper will show the path which was followed by the AMT HSM team to achieve more than a 20% productivity increase resulting in a hot coils production per year more than 700 million tons higher.

Oct 1, 2019

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

By Paulo Masiero

Sintered titanium carbide has been extensively used since the early 1980s for demanding wear-resistant applications and, in particular, in environments characterized by high temperature and oxidation. Thanks to its physical characteristics, especially its low density, titanium carbide (TiC) has been successfully applied in the manufacture of cassette guide rollers for hot steel rolling. However, the peculiar characteristics of the sintered Ti carbides make it difficult their redressing and hence this has always represented the limit for a more extensive application. Very often iron based alloys are preferred even if, in general, they are less cost effective just because they are easier to be redressed by turning. The availability of a simple, compact, fully automatic and reasonably priced CNC machine; specialized in the grinding of guide rollers and able to operate accurately and efficiently -both in contour and in plunge- can definitively solve TiC’s redressing problems and render its use even more widespread and attractive.

Oct 30, 2017

By Paul Pugsley

The need for dimensional measurement of products has always been there, now with the industry 4 push to further understand measure and to record process parameters is more important than ever. This applies to both flat and long products, camera systems have always provided the method to measure, stereo Linescan cameras for flat products and innovative applications using 2D and Linescan cameras for long products. Instrumentation will become more important to producers enabling processes to be better controlled and understood, that aim being to make the production process understandable more repeatable and less reliant on operator influence. Primetals Technologies Ltd offer solutions for all types of products.

Oct 30, 2017

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Shanti Arangala

Several improvements were made to the single strand rod mill at Laverton to increase production, reduce maintenance and improve several aspects of product quality. With changes to the water cooling line and control system, cobbles could be significantly reduced, more consistent properties obtained and yield improved. An upgrade of the laying head enabled vibrations to be reduced and thus allowed for higher speeds on small sizes. With potential for dramatically increased pipe life, a new pipe support and laying pipe system provided for improved laying pattern on small sizes and thus more uniform cooling on the conveyor and better coil package. This paper discusses details of these equipment and control system upgrades and the resulting benefits that have been realized from the project.

Aug 16, 2017

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Michel Rodrigo Luiz, Glaudistoni da Silva Félix, Osmar Duarte Junior

This article deals with a project to reduce the preparation time and threading the coils in the input section of a pickling line coupled to the cold strip mill (PLTCM) at ArcelorMittal Vega. The project developed serves for the detection and elimination of bottlenecks in the input section. The project was conceived by the philosophy of the Theory of Constraints (TOC) and Lean Six Sigma (6 sigma), here seen as sequencing serial / parallel in the preparation and threading the coils. In this context, a proposal to modify the automatic sequencing and reduction of interruptions due to failure of the automation / equipment confirmed its effectiveness reducing the total time preparation time and threading the coils in the entry section by 15%. This project was developed without investment costs, bringing gains on the order of US$613,769.00.

Oct 1, 2019

By Jean-Paul Simoes

The development of the blast furnace over the last years lead to a substantial increase in production capacity and productivity. This development triggered an evolution of the cooling systems in order to cope with the raising heat loads. The excellent protection of the shell by copper staves allowed blast furnace operators to achieve campaign lifetimes of more than 20 years. However in recent years some blast furnaces have experienced severe wear of the copper staves due to abrasion. The influences of the blast furnace design as well as of the operation conditions on this premature wear have been analysed and the mechanisms leading to the wear will be explained. New developments in the copper stave technology are part of the solution for avoiding premature wear during periods with less favourable conditions. The protection mechanisms made available by the new design extend the inherent protection mechanisms of copper staves to these periods. BFXpert® system is the ideal tool for the monitoring of the process data, the process models and the recommendations given by Sachem® support the operator in choosing efficient operation points. The charging with a Bell Less Top® (BLT) allows an accurate controlling of the blast furnace with regard to the optimization of the gas distribution. High performance operation together with long campaign lifetimes are thus made possible.

Aug 1, 2018

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019