Search Documents

By Guilherme Vitor de Araujo, Igor Cuzzuol dos Santos, Loyslene Rabelo Fernandes, Gustavo Henrique Sousa, Athos Fernandes Araujo

O desenvolvimento de nanopartículas magnéticas vem recebendo bastante atenção de pesquisadores devido a sua potencial aplicação em diferentes campos tecnológicos, principalmente em microeletrônica e medicina. A magnetita nanoparticulada é particularmente atraente para estas finalidades, pois apresenta comportamento superparamagnético, biocompatibilidade e resistencia à oxidação. Neste estudo foi avaliado a síntese das nanopartículas pela coprecipitação. Para isso foi observado a influência da razão molar de Fe+2/Fe+3 e da variação de concentração de NaOH na nucleação e precipitação das partículas. Sendo possível, determinar os melhores parâmetros para obtenção das mesmas e garantindo as suas propriedades. Para a constatação estrutural, a caracterização das amostras foi realizada por difração de raios X (DRX). A razão molar de Fe+2/Fe+3 se mostrou uma variável importante, em razões muito pequenas o resultado obtido foi goetita, enquanto a síntese a partir da razão 0,5 observou-se apenas a magnetita. E a variação da concentração de OH- teve influência no tamanho das partículas nucleadas, no qual menores partículas foram obtidas em meios mais básicos.

Oct 6, 2019

By Thiago Pinto Silva, Leandro Rocha Lemos, Luiz Fernando Andrade de Castro

This paper shows an evaluation about effect of dispersant sodium silicate along to limestone, in the form of pulp, on the cold agglomeration process for iron ore sintering. Before that, it was verified the effect of pH, solids content and amount of dispersant on the stability of the system (limestone, water and sodium silicate). It was found that the lower the solids content, the more alkaline pH and the amount of sodium silicate equal to 20 l for each 1t of limestone, was the level of dispersion of the system. The influence of the limestone pulp with dispersant depended on the granulometry of the ore mixture and the type of technological route. For the thinner type (42,8% <0.15mm), the limestone pulp with dispersant reduced the resistance of the adherent layer of the cold agglomerates, regardless of the technological route. However, for the coarser type (24,7% <0.15mm), the limestone pulp with dispersant increased the average size of the aggregates, preserving the resistance of the adherent layer when manufacturing with two intensive mixers in series.

Oct 1, 2019

By Glaucon Medeiros Silva

Este trabalho técnico tem por finalidade apresentar a evolução dos ensaios de porosidade em pelotas de minério de ferro. Apresentando as diversas formas de realização deste tipo de ensaio a não correlação entre eles, pois cada método possui uma finalidade distinta e como se ocorreu a evolução do método volumétrico (ótico) desde sua realização manual, na década de 1980, início de medições automatizadas na década de noventa e sua total automatização a partir da década de 2010 até o ano de 2019.

Oct 1, 2019

By Shun Yoshida

O trabalho apresenta os resultados práticos encontrados na aplicação do processo Oxinitrol®, em termos de aumento de vida útil, e sobrevida para moldes e matrizes de fundição sob pressão de alumínio e matrizes de forjamento a quente. Descreve os procedimentos iniciais, o processo em si, e resultados totais ou parciais, para matrizes de clientes da Combustol Tratamento de Metais Ltda.

Jul 30, 2018

By Valdeci Paula Alvarenga

Os aços alto carbono possuem maior resistência e dureza, e menor dutilidade em relação aos aços baixo e médio carbono. O aço carbono SAE 1070 é um aço plano classificado como alto carbono e possui uma microestrutura predominantemente perlítica. Algumas possíveis aplicações desse aço são: fitas de serra, lâminas para raspagem, lâminas de corte para indústrias agrícolas, entre outros. O processamento desses de aços em toda a cadeia produtiva sempre é desafiadora. O objetivo principal foi caracterizar e melhorar a microestrutura perlítica do aço SAE 1070 laminado a quente produzido na Aperam visando reduzir ou eliminar o custo adicional dos clientes de relaminação durante o processamento em suas linhas de produção. Foi possível através de análises e simulação termodinâmica refinar o grão austenítico e melhorar as propriedades mecânicas do aço SAE 1070 produzido na Aperam e como consequência a melhoria da laminabilidade a frio desse aço.

Oct 30, 2017

By Caio Trindade Almeida, Tharcysio Oliveira Rocha Paiva

Tharcysio de Oliveira Rocha de Paiva2

Oct 3, 2019

By Dalton Martins Neto, Sandro Valério Maia Larrubia, Alexandre Patricio Vieira da Silveira

A TERNIUM Brasil, Rio de Janeiro, tem em sua operação dois Altos-Fornos idênticos. Ambos iniciaram operação em 2010, Alto-Forno 01 em 13/07/2010 e Alto-Forno 02 em 06/12/2010. Em Dezembro de 2016 e Janeiro de 2017 ocorreu alguns eventos de rompimento de conjunto de sopro por temperatura alta ocasionando paradas emergências nos Altos-Fornos, perdas de produção e instabilidade operacional. Diante deste problema, a antecipação de possíveis falhas no conjunto de sopro por temperatura alta foi fundamental para garantir operação estável dos altos-fornos. Analisar o processo, verificar procedimentos, pesquisar e aplicar novos materiais para adequar as condições operacionais é essencial para evitar o rompimento de conjunto de sopro por temperatura alta e elevar vida útil dos mesmos.

Oct 1, 2019

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019

By Vagner Machado Costa

O presente trabalho tem por objetivo analisar parafusos Classe 8.8 produzidos por 4 fabricantes nacionais. Para tanto, realizou-se caracterização mecânico-metalúrgica, baseando se nas normas ABNT NBR ISO 724: 2004 [3] e DIN EN ISO 898-1: 1999 [2]. O estudo de caracterização mecânica consistiu na realização de perfis de microdureza, ensaio de tração, MEV da superfície fraturada e medição dos perfis dos parafusos. A caracterização metalúrgica seguiu através de análise química e caracterização metalográfica (macrografias e micrografias). Está caracterização é de fundamental importância para verificar as variabilidades devido aos diferentes fabricantes as quais este componente está sujeito e compreender como elas podem vir a influenciar no desempenho deste produto.

Aug 16, 2017

By Daniel Augusto Godinho de Carvalho

Since the beginning of BOF process, slag formation has been subjected to extensive development. During the initial stages of the blow, fast slag formation is primordial for the process performance. This is mainly to allow oxidizing reactions, and also to protect the refractory. A modeling of BOF process for the purpose of process optimization requires precise knowledge concerning the dissolution of CaO and MgO based materials. Using this knowledge, the optimal process conditions can be ensured by a controlling of the slag formation during the converter steelmaking process. Taking into account an application of large amount of different raw materials, as well as location-specific process conditions, the characterization of the dissolution behavior of different additives is an important key to improve the technological process. Thereby, in the frames of this project, an appropriate model for slag formation is established and compared to operational results for a 330t BOF, operating at ThyssenKrupp CSA, Santa Cruz, Brazil.

Aug 16, 2017

By Manoel Inácio dos Reis Neto

Redução no consumo específico (KW/t) de energia elétrica em um dos moinhos de bauxita na refinaria da Alumina na CBA (Companhia Brasileira de Alumínio do grupo Votorantim Metais) através do uso da Metodologia Six Sigma e ações de substituição do óleo mineral por óleo sintético de alta performance, implantação do sistema de blindagem e de resfriamento no redutor deste moinho, onde foi alcançado um resultado de 5,45% de redução neste consumo específico e de 25% na temperatura de trabalho deste redutor, superando as expectativas inicias previstas.

Jul 31, 2018

By Miguel Araújo Vasconcelos Filho, Ulisses Tetti

In order to determine the influence of the number of increments of the sinter sample on the variability of the chemical composition obtained in Sinter Plant production, a variographic study was carried out. It was performed with two series of samples. The first series was composed of 40 samples with a 6-second interval, with the objective of obtaining the so-called minimum practical error, resulting from the extraction processes of the sample of the conveyor belt and preparation and analysis in the laboratory and the second series composed of 60 samples with a range of 4 minutes, which points to the sample selection error. The results obtained showed that the minimization of the sample selection error occurs for increments spaced in 15 minutes, being in agreement with ISO 3082, but with significantly better results than those currently practiced for intervals between 1hour increments. It was then decided on the suitability of the sampler to allow hourly increments to be collected and on a second opportunity to install a sampling tower with primary and secondary samplers to collect increments every 15 minutes including sample size reduction.

Oct 1, 2019

By Gleison Vinicius Ricardo, Luiz Cláudio von Sperling Cotta, Artur Frederico Fonseca da Cruz, Evandro José de Castro Lopes

Binders are important raw materials in the iron ore pelletizing process. The bentonite, most usual, has been used in plants of this process since the forties due to its good performance in the agglomeration of ultrafine ore, although the silicon content in bentonite impairs the total iron content of the pellet, reducing its market value. This article studies the bentonite consumption reduction and improvement of the chemical quality of pellets by the addition of an organic binder in the productive process of Vale Vargem Grande pelletizing plant. By evaluation of variables as, drop test of green pellet, green pellet, dry pellet and fired pellet compressive strength tests, tumble index, percentage fraction of lower than 5 mm and total iron content in fired pellets, it was possible to approve the technical availability of the organic binder auxiliary in Vargem Grande pelletizing process. Nonetheless the positive influence of total iron content increase due to the reduction of bentonite consumption, it could also verify no impact on the physical quality of the pellets under the same production rhythm, approving once again the use of organic binders in pelletizing process.

Oct 1, 2019

By Priscilla Messias Pereira, Wellington Bonelar dos Santos, Alex Dalapicola Veronez, Maurício do Santos Rocha Junior, Leandro Resinentti Zanon

The pelletizing process allows inputs to be added to the mixture resulting in better control of the physical, chemical and metallurgical characteristics desired by the pellet. Anthracite is incorporated as input of the pellets as an alternative form of fuel, making the burning more homogeneous, "from the inside out", benefiting the physical resistance of the burned pellets and aiming to reduce the cost of natural gas during the stage of hardening. However, the amount of anthracite should not exceed an optimum value, which may cause an adverse effect on the physical quality of the pellets. Hence, it is very important an accurate control of the coal dosage. Based on that, the present study presents the implementation of a control using advanced control system that applies, using linear regression of historical data, the optimum relationship between anthracite and ore (respecting the physical quality of the pellets during processing in pelletizing furnaces). After the implementation of this control, it was possible to adjust the anthracite dosage automatically, measured in percentage of fixed carbon in the mixture, when the process is able, thus reducing the specific consumption of natural gas.

Oct 1, 2019

By Juciane Maria Alves

O aço inoxidável austenítico metaestável 304L, aço TRIP, é suscetível à transformação de fase austenita-martensita (??a’) induzida por plasticidade, a intensidade desta transformação é influenciada pela temperatura. Devido a isto, o objetivo deste trabalho foi induzir a transformação (??a’) através da laminação à temperatura criogênica, mais próxima da temperatura Mi do material. Para avaliação da transformação de fase utilizou-se a técnica de difração de raios-X e os resultados mostraram a obtenção de amostras 100% martensíticas. Devido à suscetibilidade deste material sofrer transformação (??a’) por deformação plástica avaliou-se a influência da preparação metalográfica (via polimento mecânico, químico e eletrolítico) sobre às análises quantitativas. O polimento eletrolítico se mostrou a forma mais promissora às análises quantitativas, pois permitiu a quantificação de pequena fração volumétrica de austenita retida.

Oct 30, 2017

By Jackson Teixeira de Oliveira, Douglas Batista Mazzinghy, Vanderson Eney de Matos, Alexandre Camilo Leles de Figueiredo

This work studied the effect of different ball sizes in the secondary grinding stage of Samarco. The Moly-Cop Tools 3.01 spreadsheet was used for models calibration and simulations, considering grinding balls topsize of 15, 20, 25, 30 and 35mm diameters. A normal specific selection function up to the largest fed ore particle size (840μm) was obtained. The higher generation of fines and compliance with particle size specifications (+ 74μm and -44μm) proved to be more favorable for smaller ball sizes. The specific energy consumption was lower for the 15mm ball (10.7kWh/t), increasing up to the 35mm ball (13.0kWh/t). Although smaller diameter balls seem to be the best option for the size specifications, some factors may limit their use, such as: the higher generation of specific surface area; and the amount of ball purge in the discharge of the mills.

Oct 3, 2019

By Junio Simões Pereira, Carlos Magno Nascimento, Frederic Yann Armache Braga, Luiz Cláudio Monteiro Montenegro

Given the current scenario experienced by Brazilian mining industry, the study and development of technologies that enable a more secure and controlled disposal of tailings has gained significant relevance. Among the various alternatives and disposal methodologies, Anglo American has been developing tests on three study fronts: dewatering polymers, hydrocyclone dewatering and pulp filtration. The first two fronts are intended to optimize the way of occupying the existing tailings dam. The filtering is intended to reduce the mass transfer to the reservoir, extending the life time of the existing structure. The studies were divided into laboratory, pilot and industrial phases, aiming at proving applicability and scheduling for a definitive future installation. Until this moment, all tests have demonstrated gains and potentials of applicability.

Oct 3, 2019

By Roberto Gomes da Silveira Junior, Marcos Cordeiro Fonseca, Geraldo da Conceição Morais, Manoel Gomes de Souza Neto

Sinter maximization in the blast furnaces charge has proven to be the most economically viable way to produce pig iron at Usiminas. This fact has led the company to develop projects aimed at increasing the production of sintering. In this context, the present work shows the recent experience of Sintering Machines 1 and 2 drum mixer exchanging contributing to the increase of operational productivity due to the optimization of the original design. For 13 days was the replacement of the original drum installed in 1974 by a new drum with improvements in the design of the internal and the sprinkling water system. The improvements contributed to the effective formation of micro-pellets and, as a result, increased productivity of Sinter Machines. Several aspects of the project are presented: engineering, planning, safety, manufacturing, technical quality, schedule and a comparison between the parameters of the equipment operation before and after the implantation

Oct 1, 2019

By Raquel Húngaro Costa, Jonathan Tenório Vinhal

The demand for natural resources has grown over the years, however, the environment offers a limited amount of these resources for exploration. Then, the investigation of new methods for recovering and reuse some compounds and elements are essential to know later tailings purposes. Zinc is used in corrosion resistance as a protective coating for several products. One of the steps for the extraction of zinc is by flotation process to obtain the concentrated ore, in which a residue is generated. The aim is to characterize this residue, allowing the choice of recovery routes for compounds and elements in future stages. The methods of analysis were Malvern, VA, Eltra and ICP-OES, besides the water content. In this study, a characterization of elemental chemical analysis was performed, in which the main elements presented were: calcium (17.4%), magnesium (10.3%) and iron (7.97%); the water content was 27% and the grain size of the material presented an average size of 50μm. With the presented characteristics the material can be used, after treatment, in the recovery of other compounds for applications in the sector of fertilizers, ceramics and steel industry.

Oct 3, 2019

By Anivaldo Chevane, Leonardo Xerinda, Rogério Sendela, Andre Vilanculos

Moatize Coal Mine is located in Tete Province, in centre of Mozambique. The deposit contains Gondwana allochthonous coals, and has a large amount of mudstone and siltstone banding. Phosphorus levels in the coal can be high which impacts the use of the coals in steel making where phosphorus is considered a contaminant. The Chipanga seam in the Moatize deposit shows considerable variability, vertically within the seam and laterally across the deposit. The data available from the exploration work indicates that the phosphorus is predominantly present as Apatite but the Crandallite minerals also are significant. The concentration of phosphorus varies with coal particle density with the highest phosphorus levels found for the mid density coal which also shows the highest likely levels of apatite or fluorapatite. Crandallite minerals show higher potential concentrations in the Lower density coal..

Oct 3, 2019