Search Documents

By R Bezuidenhout, J K. Claflin, S R. La Brooy, G M. Wardell-Johnson, A M. Claflin

Best practice gold (Au) recovery is not an accident. It is the result of proper operation of the adsorption circuit using good quality activated carbon. A conventional carbon ‘regeneration’ kiln cannot process carbon fouled with floatation chemicals and achieve best practice gold recovery. A high temperature, controlled atmosphere carbon ‘reactivation’ kiln is required. Carbon circuit design allows for low quality carbon by increasing the carbon advance rate, carbon inventory and setting an easily achieved and commercially prudent solution tails target of typically 0.02 ppm Au. These design criteria are important to ensure the commercial success of the gold operation in the first instance. Most carbon ‘regeneration’ kilns will produce carbon of sufficient quality to achieve a 0.02 ppm Au solution tail in the absence of flotation reagents.Best practice recovery is considered less than 0.005 ppm Au in solution reporting to tails. If the carbon is heavily fouled, as it will be if used for flotation leach circuits, then a conventional carbon ‘regeneration’ kiln cannot achieve world’s best practice recovery no matter how much carbon is advanced. World’s best practice gold recovery requires a carbon ‘reactivation’ kiln and the whole of the carbon circuit operated optimally.The competing reactions occurring in a carbon ‘reactivation’ kiln are presented and discussed in terms of kiln design and operation. New industrial and laboratory findings are presented to fill gaps in the body of knowledge and identify that a large reduction in residence time at temperature will not significantly impair reactivation, but can significantly reduce the size and cost of the kiln or permit significantly increased carbon throughput.The carbon circuit performance is modelled in terms of gold adsorption, as a function of carbon reactivation using ‘simulation of carbon-in-leach/carbon-in-pulp circuits’ (SIMCIL). An optimum carbon advance rate is identified as a function of optimum carbon ‘reactivation’ kiln operation to achieve 0.005 ppm Au in the tails solution. A conventional carbon ‘regeneration’ kiln is compared to a state-of-the-art carbon ‘reactivation’ kiln in terms of reactivation performance and gold recovery.CITATION:Claflin, J K, La Brooy, S R, Wardell-Johnson, G M, Bezuidenhout, R and Claflin, A M, 2017. Optimising carbon reactivation kiln operation, in Proceedings MetPlant 2017, pp 346–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By John G. Henning

The Hoyle Pond underground mine is located in the Porcupine Gold Camp, 18 km east of downtown Timmins. Since the initiation of production in 1985, the operation has produced in excess of 1.9 million ounces of gold at a grade of 15 grams per tonne. Currently, Hoyle Pond ranks 8th in total ounce production for all past and present producing mines in the camp, with the highest head grade of any of the significant past, or present producing mines in Timmins. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. Using illustrative examples, this paper provides an overview of factors, such as geologic setting, rock mechanics challenges and mine infrastructure, which influence mine design at Hoyle Pond.

Oct 1, 2004

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

By E. P. Youngman

In the absence of any subsequent enactment of mining legislation, the Turkish mining law in effect in 1914, when Iraq became a British mandate, is still operative. The Constitution, or Organic Law, of Iraq, adopted by the Constituent Assembly on July 10, 1924, in articles 113 and 114, provides that:3 Ottoman en laws date and thao remained and lave pub- lished on or after that date and which have remained in force in Iraq u to the time of the publication of this law shall remain in force in Iraq' so far as circumstances permit, subject to any modi- fication or repeal in conformity with the proclamations, regula- tions, and laws referred to in the following article, and until they are altered or repealed by the legislative power or the High Court issues a decision rendering them null and void in accordance with the provisions of article 86. (Art. 113.) All proclamations, regulations, and laws by the Commander-in- Chief of His Britannic Majesty's Forces in Iraq, the Civil Commis- sioner, and the High Commissioner, and those issued by the Govern- ment of His Majesty King. Faisal, during the period between Novem- ber 5, 1914, and the date of the coming into force of this Consti- tution, shall be considered to be valid as from the date on which they came into force... (Art. 114.) 4 According to a German authority, it is the Turkish law of March 26, 1906, that, with a few modifications, is still in force. This law (similar to the French law of 1810) is discussed in a separate section of this paper.

Jan 1, 1933

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By P Mulvey

"Currently mine process studies and geochemical waste characterisation are considered as two interdependent studies, necessary for the development of the mine and inclusion in the environmental impact statement (EIS). Geochemical waste characterisation will utilise the simulated tailings produced by the mine process studies team to understand the behaviour of the tailings, but the two teams rarely integrate these to develop a coherent and agreed final design.Thorough mine waste geochemical assessments can develop processes to minimise environmental harm, resulting in substantial savings in the decommissioning, closure and rehabilitation phases, and may also be able to address changes in mineral processing methods that can result in substantial savings in process inputs, or even recovery of metal concentrates.Based on geochemical waste characterisation, the full cost of waste management can be calculated and incorporated into the costing of milling.  This allows for a more effective evaluation of the metallurgy.  A number of examples are presented in which substantial improvements have been made from the collaboration of both the metallurgical and geochemical teams during planning and the metallurgical team and environmental team during operations.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Optimising metallurgy at the planning stage to minimise environmental impact - a feedback loop from geochemical waste characterisation, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

Same-batch and non-blind as well as blind pulp duplicates are often submitted as quality assurance/quality control (QA/QC) control samples to a routine laboratory along with routine assays (and other control samples such as reference material samples). The current ways of interpreting the results of duplicate assays to derive QA/QC conclusions and decisions, however, has not yet been formalised in a scientific manner. The current, prevailing approach and its limitations are reviewed and a new method is proposed as a substitute tool. This new tool should allow for operational error detection on a batch per batch basis (ie batch rejection) as well as laboratory performance assessment with time on reproducibility.

Jan 1, 2008

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

By James P. Ulery

In This Chapter [Geologic features associated with anomalous methane emissions Gas outbursts and blowers Methane drainage strategies for mitigating anomalous methane emissions and General considerations for a methane drainage program] This chapter summarizes how certain geologic features may be associated with unexpected increases in gas emissions during coal mining. These unexpected emissions have the potential to create explosive conditions in the underground workplace. Also discussed are the generally used practices to alleviate potential hazards caused by gas emissions associated with these geologic features. INTRODUCTION Unforeseen mine gas emissions in quantities sufficient to create hazardous conditions have been attributed to sources outside the mined coalbed since the first documentation of methane explosions in coal mines [Payman and Statham 1930]. Geologic features such as faults have long been recognized as conduits for gas flow from strata adjacent to mined coalbeds [Moss 1927; Payman and Statham 1930]. Other features such as sandstone paleochannels, clay veins, and localized folding have also been recognized for their impact on gas emissions into mine work-ings [Darton 1915; Price and Headlee 1943; McCulloch et al. 1975; Ulery and Molinda 1984]. The fact that strata adjacent to mined coalbeds can emit large quantities of methane gas into mine workings is not surprising from a theoretical perspective. Many researchers have recognized that during the burial and diagenesis of the organic matter forming today’s minable coalbeds, similar dispersed organic matter in adjacent strata has produced methane in quantities far exceeding the storage capacity of the coal and surrounding rock [Juntgen and Klein 1975]. It is not surprising then that large quantities of methane can remain trapped in these strata. A potential hazard occurs when mining of a nearby coalbed causes pressure differentials and mining-induced fractures conducive to gas flow into the mine workings from these strata. This gas flow may be facilitated or temporarily impeded by the presence of geologic structures or anomalies.

Jan 6, 2006

By I. C. L. Webster, G. E. Ray

"The magnetite-rich Heff Cu-Au skarn lies in the Quesnel Terrane of south-central British Columbia, approximately 26 km northeast of Kamloops. The skarn formed close to the northern margin of the Heffley Creek pluton, and is hosted by Carnian (Late Triassic) Nicola Group limestone. The Late Triassic pluton (208.1 ± 6.1 Ma, U-Pb zircon) is a composite body of alkaline affinity that includes dioritic, gabbroic, and magnetite-rich clinopyroxene ± olivine ultramafic phases.The skarn has been discontinuously traced along strike for more than 1 km, and individual skarn layers are up to 40 m thick. The most common non-opaque minerals are garnet, clinopyroxene, and carbonate, with lesser epidote, biotite, amphibole, and chlorite. Apatite locally forms more than 3 vol.% of the rock. Compositionally the garnet is a low Mn grandite averaging Pyr3-Grs41-Adr56 mol.%.Mineralization consists of lenses, up to 10 m thick, containing massive low Ti-V magnetite (avg. 0.03 wt.% TiO2 and 0.01 wt.% V2O3). Magnetite is associated with up to 20 vol.% pyrrhotite, lesser pyrite, and trace chalcopyrite and gold. There is a moderate enrichment in rare earth elements with assays up to 570 ppm La and 490 ppm Ce. The Heffley Creek pluton belongs to a suite of Late Triassic-Early Jurassic alkalic and Fe-rich intrusions that are widely developed throughout the Quesnel Terrane. Some host Cu-Au porphyry mineralization, but less commonly they are associated with magnetite-apatite veins such as at the Glen Iron mine and Magnet occurrence, or with magnetite-rich Cu-Au skarns such as the Heff occurrence.Although abundant low Ti magnetite is present in the Heff skarn, it does not appear to represent iron oxide copper- gold (IOCG) type mineralization. Microprobe analyses completed during this study show that low Ti magnetite is not a unique feature of IOCG deposits, but also characterizes some other types of hydrothermal mineralization. In British Columbia these include some alkalic porphyry-related magnetite-apatite veins in the Quesnel Terrane, as well as the well-known Wrangellia-hosted Fe skarn deposits. Thus, low Ti magnetite appears to be a common signature of many magmatic hydrothermal deposits in contrast to the high Ti primary magnetite found in most igneous rocks."

Jan 1, 2007

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

By Arun .. J. Basu

The paper introduces Intelligent Air Management (IAM) as the core activity of M&I Group of Companies (M&I) for providing a total solution to any air management problems for mining and mineral processing operations implementing a comprehensive systems approach through a world-wide network of strategic alliance partners and in-house engineering team and manufacturing facilities in Mississauga, Ontario, Canada. Recommendations for energy-efficient ventilation in a vibration and noise free environment are made with the patented and innovative solutions supported by extensive computational fluid dynamics (CFD) studies. The solution scope extends from an intelligent and integrated exhaust silencer to a complete ventilation sys-tem solution including inlet and outlet control design and ducting for diffusers and silencers.

Apr 1, 2005

By J. Geisler

When addressing Germany’s resource supplies, we need to distinguish between those domestically available and imported ones. Resource extraction ostensibly competes with the designation of protection areas. However, the parallel existence of wildlife and plant life, and operations in the areas used for resource extractions is continually underestimated. The European Commission has compiled guidance documents facilitating the extraction of resources from protected areas. With regard to resource productivity, the market appears to be the appropriate instrument for minimising resource consumption. Policy makers are now called upon to create a legal framework leading to a consensus accepted by society.

Jan 1, 2011

THE old mill erected by the .Irvinebank Company consisted of 10 heads of stamps (850 lb.), rock-breaker, Hartz jig, two Krupp tables, two Luhrig vanners, three sand-pumps, one mixer; six flotation vessels, and the necessary settlers. Power was supplied by a small colonial-type boiler, and 10-in. x 15-in Tangye engines. The ore was darted from the mines to the mill and hand-fed, into the rock-breaker, and the broken product elevated into the batter bins and fed into the stamps, the pulp from the stamps passing to a classifier, the spigot to jig, tables, and vanners, the overflow from the classifier passing to settlers. After the removal of bismuth-wolfram concentrates, the pulp was pumped to the molybdenite flotation plant and the olybdenite recovered by flotation.A commencement was made with the erection of the first unit (20 heads) of the new mill in August, 1917, and milling and concentrating commenced in February, 1919.

Jan 1, 1920

By S. Möllerherm

"The evaluation of data and information provided by the existing traditional indicators in sustainability assessments is most important. Therefore the Institute of Mining Engineering I from the RWTH Aachen University developed indicators and an assessment system for the mineral raw materials industry on operation, company and sector level on behalf of the Federal Ministry of Economics and Labour (Bundesministerium für Wirtschaft und Arbeit, BMWA) and the Federal Institute for Geosciences and Natural Resources (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR). In the course of the development of indicators for the raw materials industry quality indicators on different levels of the sustainability assessment procedure have been identified and developed. The following paper describes some of the results focussing on the development and integration of quality indicators into sustainability assessment systems."

Jan 1, 2005