Search Documents

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By Ovidiu Pasca

The Phelps Dodge Miami Smelter utilizes four Hoboken converters to process molten matte from the Isasmelt vessel. This paper presents past and present improvements in operation, maintenance and process optimization, based on data collection, which has led to increased converter campaign life and copper throughput.

Jan 1, 2005

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By A. Drouin, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%.IntroductionDundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale.DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology.DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

By P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mining and exploration properties have a unique set of technical risks. Privately-owned companies considering investing in the resources sector can optimise their investment decisions by adopting a systematic technical assessment of acquisition assets, similar to the approach commonly adopted by public financial institutions and publicly-listed companies.Technical due diligence provides a process to identify key geological, mining, geotechnical, metallurgical, environmental and social risks and opportunities and determine the most likely business case and valuation of assets. Technical due diligence is commonly carried out in parallel with legal, commercial and financial due diligence, often involving the acquirer, to maximise the understanding of the investment.There are significant advantages in investors conducting a comprehensive technical due diligence, which typically involves site visits and project assessment to international standards by an independent, multidisciplinary team of experts. The outcomes provide the opportunity for the investor to make early, informed decisions and to understand and manage risks.Technical due diligence may be carried out at several stages: when considering and weighing up a number of investment options, prior to and during a transaction or immediately post-transaction. In the first stage, the outcomes will inform the choice of investment and, more particularly, whether there are any fundamental flaws in the projects being considered. In the second stage, due diligence outcomes can inform the level of investment and approach to risk management and planning. In the third stage, risks and opportunities can be investigated in more detail, allowing the investor to consider the best options to reduce risk and maximise the benefit of the investment.This paper presents a summary of the technical due diligence assessment process, its benefits to investors, common risks in mining and exploration projects known to cause mining asset write-downs and principal technical due diligence approaches.CITATION:Keogh, A, Stoker, P and Thomas, M, 2015. Benefits of due diligence in private equity mining investments – maximising value and unearthing common risks , in Proceedings PACRIM 2015 Congress, pp 115–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Linn M. Farish

SOVIET RUSSIA reserves must be stupendous. In 1937 I. M. Goubkin placed the reserves of all categories it approximately 48 billion barren which was about twenty billion horn Is in excel:, of all the oil produced in the world since 1857. It is not unlikely in fact it is probable, that these huge stores of petroleum may ultimately be proven to exist within the present boundaries of the U.S.S.R. The size of the country is almost beyond imagination it is 2.7 times as big as the United States. Great sedimentary basins exist in all its different geological provinces, much of which are entirely untested and barely prospected. Oil in commercial quantities is actually produced from formations in every period from the Devonian to the Pleistocene. In the Emba region alone, 300 salt domes are known with an estimate of 700 still to be found. Only 22 of the 300 have been drilled and all showed oil. Of the 22 domes drilled six are now producing. There are 400 mapped structures reported in Azerbaijan

Jan 1, 1940

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

Organization Place Date 1919 American Electrochemical Society New York, N. Y. Apr. 3-5 American Chemical Society Buffalo, N. Y. Apr. 8-11 National Foreign Trade Council : Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y: May American Institute of Electrical Engineers Lake Placid, N. Y. June 23-27 American Society for Testing Materials..: Atlantic City, N. J. June 24-27 American Railway Bridge and Building Association Cleveland, O. Oct. 21-23

Jan 4, 1919

By L. W. T. Weitzel

"This paper reviews the Falconbridge- SMRQ’s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40 km property strike length. As a result of its remote northern location, other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel-based financial spreadsheet to bring the total plan together. The focus of the paper is to show the complexity of modern mine planning and associated economic modelling of mine processes. IntroductionThe Raglan project is located 1660 km directly north of Quebec at the northern tip of the Quebec Peninsula in Nunavik. The main property is 40 km in length stretching from the Donaldson airport area at the eastern edge of the property to East Lake at the western edge. The Deception Bay port is 90 km north of the main complex/mill situated at Katinniq which lies approximately in the middle of the property (Fig. 1). The mine processes 1 000 000 tpy of ore from both open pit and underground sources. The mill is forecasted this year to produce more than 150 000 t of concentrate grading more than 18% nickel. All personnel and critical cargo are transported to the site via a company-leased 737 jet from Rouyn-Noranda where the main administration office is located. The majority of cargo is shipped to the site via Deception Bay from Quebec and on the return trip, nickel concentrate is shipped back. From Quebec, the nickel concentrate is sent by rail to the Falconbridge smelter in Sudbury and on the reverse rail haul, nickel matte from the smelter is sent to Norway via Quebec."

Jan 1, 2003

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

"INTRODUCTIONThe information compiled in this volume initially formed the response by the Generic Mineral Technology Center for -Respirable Dust (GTCRD) to a review of its research and technology transfer programs performed in 1990 by the Advisory Committee on Mining and Mineral Resources Research. This review for each mineral technology research center is accomplished, as required of the Bureau of Mines by the House/Senate Joint Conference Committee, through site visitation to the research institutions of the GTCRD and an in-depth questionnaire. The information provided by that questionnaire becomes an important factor in their recommendations concerning future directions of the program.The site visitations took place during January and February 1991 at the Milton S. Hershey Medical Center~ The Pennsylvania State University, West Virginia University, University of Minnesota, and Michigan Technological University, in addition to an in-mine visit conducted at the Loveridge Mine in West Virginia. The questionnaire was prepared and made available to the Advisory Committee and the Research Council for their review at the GTCRD annual project review meeting in Hershey, Pennsylvania, in April 1991.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now helps to guide it into the future. It is believed that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members. Each aspect of the questionnaire was examined, answered in detail and documented thoroughly. With the completed questionnaire as a guide, this review of the Center's activities provides an update to Respirable Dust Center Research Program Review 1988, published in 1989 as the seventh of the Generic Mineral Technology Center for Respirable Dust volumes. As does that volume, this review presents the complete General Mineral Technology Center questionnaire, with the GTCRD's expanded responses and supporting documentation appended. An examination of the research program, Center personnel currently active on GMTC projects, the number of graduate degrees granted with GMTC supports GMTC publications, the degree of individual interaction, technology transfer activities, the reference center, GMTC equipment and facilities, and envisioned plans for future research directions provides updated information in these areas. In addition, this year, information has been included to demonstrate the interaction between the Center's goals and its research projects, with thorough consideration of actual research needs as specified by the National Academy of Sciences. This volume serves as a review of the years 1989 through 1990, the sixth and seventh years of the Center's operation."

Jan 1, 1990

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

As it is probable that a large proportion of the members of the Institute attending this meeting are connected with the metalliferous side of mining, the writer thought that, as coal and coke are required for various purposes in considerable quantities by their companies, some particulars of the coal industry might be of interest, especially when visiting such an important coal-mining centre as Newcastle. It is proposed to deal with the matter from the mining and economic point of view, as the geology has been so well and exhaustively dealt with in various publications referred to in the bibliography at the end of this paper. In the immediate vicinity of the city of Newcastle the collieries are gradually being abandoned, and during the past few years the Wickham and Bullock Island, Stockton, Hetton, Newcastle Coal Mining Company's "B," and the Australian Agricultural Co's Sea pit, have disappeared from the coal-producing list of collieries. AIl of these collieries worked the Borehole seam, from which, up to date, the largest quantity of coal has been produced in the northern district.It is the bottom seam of any present commercial value in the Upper or Newcastle coal-measures, and although the coal-in this seam has not been entirely 'exhausted in the collieries referred to, they have been abandoned for various reasons. For example, although about 60% of the seam (18 to 20 ft. thick) was left in the workings in the form of rectangular pillars under the city of Newcastle, this was not sufficient to 1?revent'the subsidence which took place about twelve years ago.Again, large quantities of coal in the Borehole seam have been left to protect the shipping arrangements at the Dyke, and other...

Jan 1, 1918

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By G. J. Knighton

Introduction The Sullivan concentrator treats the complex lead-zinc-iron ore from the Sullivan mine of the Consolidated Mining and Smelting Company of Canada, Limited, to make a lead and a zinc concentrate for its metallurgical plants at Trail. Three miles separate the mine and mill, which are situated near the town of Kimberley, in the East Kootenay district of British Columbia. The orebody consists typically of banded sulphides, mainly galena, sphalerite, pyrrhotite, and pyrite. Important factors in the concentration of the ore are its exceedingly complex and its high specific gravity. It should be remembered throughout the paper that results and figures are based on Consolidated's experience with the Sullivan ore. The present mill feed rate is 8,500 dry tons of ore per 24 hours, for an operating week of five and a half days. Grinding and classification of the ore are carried out in three stages and, in addition, there is a re-grind section which re-treats the zinc middling. It is the purpose of this paper to discuss the classification in the various stages and to give the results o comparative tests which have been carried out for the purpose of improving operations in the mill. The Primary stage consists of six units, each made up of a ball-mill and classifier (see accompanying flow-sheet). Four units operate in open circuit and two in closed circuit. The secondary stage consists of eight ball-mills operating in closed circuit with twenty-one classifiers. In the Tertiary stage are two ball-mills in closed circuit with eight classifiers. The re-treatment section for re-grinding the zinc middling comprises one ball-mill in closed circuit with two classifiers.

Jan 1, 1947

By Patrizio Damiano

Competitiveness in Electric Arc Furnace production is pushing steelmakers to increase the throughput at the lowest expenditure. The technological challenge is therefore to operate the existing facilities at their top capabilities and to exploit materials and energy sources at the upmost yield and efficiency. Moreover, seizing the opportunity offered from the price variability of metallic feedstock calls for flexible practices, versatile equipment and tools to rapidly tune the melting profiles without hindering steel quality and equipment lifetime. The innovative Danieli Q-MELT Automatic EAF system addresses these aspects implementing a centralized control system which interacts with multiple technological packages. Each of these cutting-edge technologies focuses on one aspect of the EAF cycle, increasing machine availability and resource efficiency, by means of electrode regulation and foamy slag control, charging optimization, off-gas analysis and closed loop injectors control. Moreover, these modules provide the process supervisor application (Melt Model) with important information regarding the process status, thus allowing the adoption of a unified control strategy. The supervisor implements a robust statistical approach to identify process deviations in real time. The first results and technology perspectives inferred from the field immediately after the start-up are described in this paper.

Oct 30, 2017

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014