Search Documents

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By L. J. Vincze

The high cost of constructing mineral processing plants in remote locations warrants a close examination of the alternatives available for reducing the amount of on-site construction work. Among the alternatives are portable process plants, modular design and barge mounted plants. Each alternative has certain advantages as well as limitations depending upon specific conditions. On the basis of practical experience and engineering analysis, the paper examines the potential benefits to be realized by these techniques and summarizes the conditions required to obtain them. The potential savings indicated by such studies should encourage consideration of innovative design features for new plants located in remote areas.

Jan 1, 1980

By T Christie, A Swain

Patterns of quartz veining in epithermal gold-silver deposits at Wharekirauponga, Neavesville and Ohui in the Hauraki Goldfield, have been analysed to determine the effects of different lithologies on vein distributions. At Wharekirauponga, quartz veins are hosted in rhyolite and minor andesite, with the andesite containing slightly higher gold grades. Local basement andesite, rhyolitic tuff and silicified black shale host gold-bearing quartz veins at Neavesville. At Ohui, quartz veins are hosted in rhyolite, rhyolitic tuff and andesite. Fractal analysis was used to quantitatively describe the distribution of veining. The fractal dimension (D) of veining in silicified tuff is 0.25, moderately silicified rhyolite has D = 0.23 - 0.26, clay-altered andesite has D = 0.3, strongly silicified rhyolite has D = 0.3 - 0.39, silicified andesite has D = 0.4, and silicified black shale has D = 0.43. The D values are related to the composition of the host rock, and appear to be controlled by its competency. Hydrothermal silicification results in increased competency and higher D values. Vein thickness frequency plots for different lithologies show that andesite at Ohui, and to a much lesser degree at Wharekirauponga, contains more thick veins than rhyolite and tuff. Gold grades show a strong to fair correlation with higher vein density in three drillholes at Wharekirauponga. The fractal dimension of veining is an important control on fluid flow and gold deposition within an active epithermal system. Vein systems with higher D have a greater density of veining which would have favoured increased fluid-rock interaction. Lower D vein systems have more clustered arrays. The increased fluid-rock interaction induced by a high D vein system, when combined with a reactive host rock, results in an environment which is highly favourable for gold deposition. This situation is seen in the andesite at Wharekirauponga.

Jan 1, 1994

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By H. Saridikmen, C. S. Kucukkaragoz

In the present study, the measurement of sulphur distribution ratios between the slag and metal phases encountered in the ferromanganese smelting has been carried out at 0.83 atm of partial pressure of CO at 1773 K by using classical gas-slag-metal equilibrium quenching technique as a function of composition. The distribution results were employed in calculating the sulphide capacities of SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.-S metal phase. It is shown that the sulphur transfer from metal to slag phase increases with increasing the basicity of the slag. As expected, the sulphur distribution ratio decreases by increasing the silica content of the slag system. The effect of metal composition on the sulphide capacities of the slag as well as on the sulphur distribution ratios between the slag and metal phases have been discussed. Emprical relationships were developed to express the sulphur distribution ratios and sulphide capacities of the above slag system.

Jan 1, 2007

By J. H. Zietsman

Ilmenite smelting furnaces must be operated with a freeze lining of frozen slag to protect sidewall refractories from chemical attack by liquid slag. The process has two main control objectives: Firstly the slag TiO2 content must be controlled according to specification, and secondly a safe freeze lining thickness must be maintained. This text only concerns itself with the second objective. Freeze lining thickness cannot be measured directly due to conditions inside the furnace. It is therefore inferred from signals of thermocouples installed into the furnace sidewall. These signals are used as the 'controlled variables' in the freeze lining thickness control loop. The dynamic characteristics of these signals are the focus of this text. During this study a model of the process was constructed to study interactions between the slag bath and the freeze lining. This model was used to conduct simulation-type experiments to study the influence of various parameters (temperature, slag composition, ilmenite feed rate, reductant feed rate, power input, etc.) on the slag bath, freeze lining, metal bath, furnace wall and other parts of the process. In the case of the furnace wall, the modelling results were first plotted in the form of time-dependent isotherms. The dynamic thermal behavior of the furnace wall became evident from these results. To illustrate the dynamics of sidewall thermocouple signals, the results were also plotted as time lags between events occurring in the slag bath, and the time when a thermocouple registered a temperature change. The events studied included sudden changes in slag bath state (composition and temperature), changes in operating setpoints (ilmenite feed rate, reductant feed rate, power input), and operational errors (complete loss of reductant or of all feed). All of the result sets showed significant lags between occurrences in the slag bath and temperature changes in the refractory wall. The delays are such that it appears impractical to rely on sidewall thermocouple signals for warning of impending damage to the refractory wall, or for purposes of actively controlling freeze lining thickness. Some measures are suggested to improve the usefulness of these signals during furnace operation.

Jan 1, 2005

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

By S Kasaneva

TheSan Cristobal gold district is located 110 km east of the port of Antofagasta, Chile. It contains the San Cristobal gold mine, where Niugini Mining Ltd. commenced a heap leach operation, with initial reserves of 10.1 million tonnes grading 1.34 g/t Au, in December, 1990. The San Cristobal district occurs within an upper Cretaceous-lower Tertiary magmatic arc. The main mineralisation occurs within a northwest trending subvertical zone, 1km long and 70 - 100 m wide, which contains rhyolite porphyry and minor breccia, and is locally termed the 'subvolcanic complex'. At the San Cristobal mine, most gold mineralisation occurs in subvertical quartz-pyrite veins which were emplaced in dilational sections of an imbricate fault system. The bulk gold resource comprises four ore shoots which formed where the vein system intersects the subvolcanic complex. Gold-bearing quartz-pyrite veins also occur at separate prospects, the Three Sisters and Sol prospects, west and south of the San Cristobal mine.   Hydrothermal alteration consists of potassic and propylitic assemblages related to intrusion of the subvolcanic complex. This alteration is overprinted by a phyllic stage which is associated with the emplacement of the quartz-pyrite veins. The oxide zone is 180 m thick, and contains native gold, electrum, limonite, and manganocarbonates. The underlying hypogene zone contains pyrite with minor chalcopyrite, sphalerite, galena, covellite, bornite, chalcocite, and arsenopyrite. Fluid inclusion studies indicate that the deposit formed at approximately 270¦C, and the mean salinity of the fluid was 4% NaCl equivalent. These observations enable the San Cristobal deposit to be classed as a porphyry- related, mesothermal quartz-vein system of the low sulphidation type.

Jan 1, 1995

By S J. Loach

Geological reconciliation is an indispensable part of BHP Billiton’s Western Australian Iron Ore (WAIO) operations. Since 2009 our reconciliations have been calculated in a single, centralised sequel-server database. This system draws data from across our operations and calculates a hierarchical sequence of reconciliation factors that span the company from the smallest grade control (GC) block to the whole of WAIO. It then presents the results using sophisticated graphical reporting tools.The initial motive for developing WAIO’s reconciliation system was to meet corporate compliance and public reporting requirements. The ability to validate our resource and reserve models by comparing their estimates of tonnes and grade with production figures remains the system’s principal function; however, as the system has matured, we have significantly developed its ability to support the improvement of various technical activities within the business. For example, the system can now calculate and report reconciliation factors for different resource classifications, short-term planning models and geometallurgical estimates.More recently, great emphasis has fallen on the system’s ability to detect and warn of possible geological issues that may pose a risk to either production schedules or product quality. We envisage a future where automated analysis of our large historical data set will enable high-risk conditions within future mine plans to be detected and highlighted.In all of these ways geological reconciliation plays an important role in contributing to this company’s financial and operational resilience.CITATION:Loach, S J, 2017. The development and future of BHP Billiton’s Western Australian iron ore geological reconciliation system, in Proceedings Iron Ore 2017, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. W. Jones

"INTRODUCTION As part of its work in promoting safety, the Bureau of Mines is investigating various means of eliminating or mitigating the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explosibility of many complex gaseous mixtures may be calculated in a rather simple manner without the necessity of performing laborious laboratory experiments. An earlier publication 3/ described the method of determining by calculation the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen. The information published in the above report permitted calculation of the limits of inflamnability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust gases, gases present after mine explosions, blast-furnace gas, and other gases of similar type.Gases liberated in certain potash mines in the western part of the United States sometimes contain ethane, in addition to the gases named. An investigation was made to obtain data from which the limits of inflammability of such gaseous mixtures could be determined by calculation. 4/Similar data have been Published covering all types of natural gases containing wide ranges of concentration of nitrogen and carbon dioxide.5/"

Dec 1, 1944

By James Green

It has often been said that the best contracts written are by people who are suspicious of each other. The Spanish philosopher, Ortega y Gasset, said: "Every contract is an Act of Distrust." The arena for dispute settlement outside of the courts is increasing day by day - contracts, especially construction and civil engineering contracts, are written containing arbitration clauses for settling disputes - the very drafting of standard forms of contract, do in some instances by their very construction, create an ambiguity as to intent and provide a breeding ground for dispute. I come from a land far across the sea - the most southern land before the South Pole. Being a young country, 150 years old, we are still progressing - being far removed from the trouble free zones of the world and nuclear free we enjoy a lifestyle second to none.

Jan 1, 1987

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

Atlas Copco Construction and Mining Australia identified a number of issues in regard to the skill levels, labour turnover and productivity of our service technicians. In 1994 we were experiencing a labour turnover rate of 42 per cent per annum amongst our technicians. Exit interviews were held with each individual and one of the major areas of dissatisfaction was the degree of product training provided on our equipment, compared to what is required to be competent across the range of our products. These tradespersons were prepared to accept the reduced remuneration that an OEM offers, for the benefit of comprehensive, professional training that, in theory, could be provided. The truth is that we were achieving approximately 40 per cent of our target for training hours because of the demands of field service, pre-deliveries, etc. So, the summary was the same as the industry was experiencing at that time because of skilled labour shortages, production demands, etc people were employed and thrown in at the deep end. A recipe for failure that will be successful every time.

Jan 1, 1998

Au-Ag Recovery from Complex Ore by Flotation

Sep 13, 2010

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway's largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By A. D. Dalvi

With the current economic situation, the demand for nickel and other base metals has fallen significantly. More than 440 kt/yr world nickel capacity has been taken out of production within the last year, or more than 25% of the total [1]. This situation is similar to that at the end of 1970?s and it will take a number of years for the demand to recover to the levels before the economic downturn. In the meantime, the challenges facing the industry have increased due to diminishing ore grades, more inaccessible and complex deposits, mounting capital and operating costs and the various external pressures which include socio-economic, environmental, and energy challenges. All industries will be faced with paying the ?total ownership costs? in the future. This will only increase the burden on the industry. How to cope with this in what Thomas Friedman calls the ?Energy-Climate Era? [2] will be the most pressing challenge for the next generation of metallurgists and managers. It will force us to take a broader view of the problems and the solutions beyond mere technical. The metallurgists, engineers and project managers will have to look at the overall projects and their objectives in designing the solutions, requiring a top-down strategic approach.

Jan 1, 2009