Search Documents

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or EPD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to – 2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to –2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: –2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals."

Jan 1, 2003

WMC was a late entrant into Indonesia in mid-1996, but had considerable experience and success in exploring in Asia, particularly the Philippines since 1988. Given the geological similarities to the Philippines and IndonesiaÆs superior æcradle to graveÆ Contract of Work (CoW) tenure system, the entry into Indonesia was a logical decision but nonetheless a result of detailed planning. At the time of WMCÆs entry, Busang in Kalimantan was still a 60 moz wonder and the euphoria of this apparent discovery had overflowed into every aspect of exploration. Many junior mining companies and tenement speculators were clamouring for properties in Kalimantan, whilst other serious and capable explorers had to compete for properties and exploration personnel in an era of high and often unrealistic expectations. The picture in late-1998 and through 1999 is dramatically different, as the worldwide downturn in the price of most metals coincides with financial and social crises throughout most Asian countries. The impact of this has been particularly severe in Indonesia and when coupled with the negative sentiment of the Busang fraud has resulted in an exodus of junior companies and also some of the majors. This is understandable given the much publicised social unrest, uncertainty of government, mooted changes to the eighth generation CoW, increasing illegal mining and heightened community expectations. The reality however is somewhat different and although clearly a crisis in many respects, it is also a time of great opportunity.

Jan 1, 1999

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By Joseph L. Fournier

Suncor Oil Sands employs delayed coking technology in converting bitumen into synthetic crude oil. Currently up to 10,000 m3 of delayed coke (coke) is produced per day as a byproduct of the upgrading process, of which up to 9,000 m3 per day is placed in dry storage on Lease 86/17. A review was completed to examine the case history of leachate potential experiments from the dry storage of coke and the environmental relevance of coke leachate studies conducted over the past decade. The review included an evaluation of the potential impacts of environmental conditions within the location of coke storage, including precipitation pH, as well as daily and annual ozone trends. Coke leachate potential has historically been characterized using standard leachate testing protocols (i.e., TLCP, SPLP) together with other studies that have employed strong acids and oxidizing agents in the extraction fluids. The present paper highlights prevailing conditions in the Athabasca Valley air-shed with emphasis given to ambient ozone (oxidizers), as well as precipitation pH and acid input deposition rates, and will demonstrate that TCLP / SPLP tests lack the intended environmental relevance relative to the conditions under which coke is stored.

May 1, 2011

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019

By M. Feely, W. G. O'Keefe, C. O'Reilly, M. P. Holdstock

A petrographic and microthermometric study of fluid inclusions in the Kentstown Granite, crosscutting quartz (VI) and calcite+quartz (V 2) veins in the granite and calcite+quartz (V 2) veins in the overlying sediments was performed on samples taken from the borehole. Comparisons of the type 1, type 2 and type 3 fluid inclusion populations recorded in the present study with those from other Irish Caledonian granites strongly suggest a similar fluid evolutionary history. Furthermore, the low-temperature CaC12-rich brines (type 5) of this study, which must be syn- to post-Lower Carboniferous in age, have correlatives both in Irish Caledonian granites and in the Lower Carboniferous base-metal deposits of the Irish midlands

Jun 19, 1905

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"Rare Earth water dregs is the drained waste dregs, which contains over 0.2 percent thorium dioxide and about 6-10 percent di-Rare Earth trioxide, which is beyond the standard of draining off that China governments set, so that the Rare Earth water leach dregs must be sacked and laid down in storehouse, which costs lots of money. It is a pity that the RE and thorium compounds very useful elements in industry are discarded. A lot of work must be carried out so that this resource was fully developed.In this paper, four separation techniques of recovery Rare Earth minerals and enrichment thorium element and reduction thorium content of drained dreg for the different test samples of Rare Earth water leach dregs which is radioactive waste dregs got from diverse locus are studied, respectively, and the separation characteristic and the separation process are described, using several combination processes of classification and gravity and flotation separation which were prepared according to the characteristic of test samples and technology. The test results show that the combination processes are the more remarkable separation techniques and the flotation reagents used in test can be applied to utilizing synthetically radioactive waste dregs. Through the combined technique process, three parts of products were obtained, namely, Rare Earth concentrate collected, the thorium product enriched and a large amount of the waste dregs product that can be directly drained and the total quantity is 50%-60%. In order to determine optimum technical condition, the effect factors of separation process were investigated in the test."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of some silicate minerals (i.e., feldspar, quartz and wollastonite) after contacting different triboecharging medium made of different materials were studied. The charge acquisitions by different size fractions of minerals were monitored and accordingly the energetic work function values, i.e., the main parameter determining the entity of triboelectric charges acquired by mineral grains, of the examined minerals were estimated. Moreover the separation behavior of different size fractions of these minerals through the electric field of a laboratory free-falling separator when the mineral grains are charged by different tribochargers were observed and considered as the electrical separation potential of the examined minerals.Furthermore, the role of adsorption of different chemical species on triboelectric charge characteristics and charge acquisition of mineral samples were described from theoretical point of view and the effects of some chemical reagents on triboelectric charge acquisition of the examined minerals were studied. In addition the separation behavior of chemically conditioned quartz, feldspar and wollastonite minerals, using different anionic and cationic reagents, through the electric field of a free-fall electrostatic separator before and after chemical conditioning were monitored.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing mainly of feldspars, quartz, and wollastonite. Different separation tests under various conditions were conducted to this complex silicate ore. Before passing through the separation device, the ore sample was conditioned by different cationic and anionic reagents and then was triboelectricaly charged by different tribocharging medium in order to find the effective reagent and tribocharging medium for separating silicates. Besides the role of temperature and humidity of the surrounding ambient in separation behavior were considered."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

? Develop a six year capital budget for future emission controls at Western Springfield Power Plant that would provide long-term operating certainty

Jan 1, 2005