Search Documents

By J Bresnahan, D Kepert, R Murray, R Neroni

Stratigraphy of the Hamersley Province in Western Australia, featuring alternating units of banded iron formations and shales with contrasting electrical properties in a mostly gently undulating shallow-dipping layered geometry, is particularly favourable to airborne time-domain electromagnetic mapping techniques. Manipulated vertical cross-sections of modelled conductivity obtained from laterally constrained one-dimensional inversion of SkyTEM304 data enable the exploration geologist to interpret weathering profiles, shallow-dipping stratigraphy and steep structures, all of which are crucial aspects of bedded iron ore deposits genesis models.The Cobra Project is located 14 km east of the NNW-trending Menindee Fault Zone, which defines the western margin of the Hamersley Province, Western Australia. The region comprises an extensive plateau of Brockman Iron Formation cut by a series of horst and grabens with a regional dextral strike-slip component. The 150° striking horst and grabens and associated 060° striking conjugate faults have approximate frequencies of 400 and 2000 m, respectively, and control the bulk of the iron mineralisation. Syn to late 150° trending dykes in part intrude the faults.In the Cobra region, elucidating the structurally dislocated stratigraphy without closely spaced drilling is very challenging. Geological mapping is hindered by the paucity of mappable stratigraphic markers within the banded iron formations and kinematic indicators. Airborne magnetic and remote sensing data sets highlight the dense lineament network, but provide limited assistance in quantifying relatively small apparent displacements, or distinguishing faults from dykes with reasonable confidence.Interpretation of modelled conductivity cross-sections generated from laterally constrained one-dimensional inversion of airborne electromagnetic method (AEM) data offers invaluable insight where the quality of mapping or drilling is wanting. Subsequent targeted field checking and infill drilling validated the geological model interpreted from the integration of these data sets.The AEM technique alone cannot decipher the complex geological environments often present in the Hamersley Province but can facilitate effective iron ore exploration by focusing precious field time and assisting structural and stratigraphic interpretations in areas with sporadic and shallow geological data.CITATION:Murray, R, Neroni, R, Kepert, D and Bresnahan, J, 2017. Using airborne electromagnetics to solve a structurally complex geological puzzle in the Hamersley Province, Western Australia, in Proceedings Iron Ore 2017, pp 269–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

Jan 1, 1959

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very' high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the 'Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the· normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960

By Stephen Iverson

The National Institute for Occupational Safety and Health (NIOSH) is currently performing research to help mine operators minimize the amount of loose or damaged rock surrounding a blasted opening. Improperly designed blast rounds can result in excessive wall rock damage that may reduce the rock mass competency and increase ground support requirements. Unnecessary blast damage can cause many safety and operational concerns including an increased potential for injury from rock falls and other hazards resulting from sub-optimal blast designs. This paper focuses on the ground control and safety implications of blast damage in underground mines. A reduction in rock quality due to blasting can increase the amount of ground support required. Case study data collected by NIOSH in underground metal mines during standard drill and blast production rounds included blast vibration monitoring, detailed three-dimensional laser scanning of the as-built excavation, and geotechnical mapping of development headings.

Jan 1, 2007

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By R. G. McLusky

This paper analyzes the opinion in Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D. W.Va. 1999), a case which threatens the future of surface mining in West Virginia and which will almost certainly result in new policies or rules that will affect surface mining everywhere. This paper addresses: (1) the jurisdictional bases of the action which relies on the federal surface mining laws to enforce a state mining program; (2) settlement agreements reached in the case that threaten to alter federal policies beyond West Virginia borders; (3) a programmatic environmental impact statement on mountaintop mining being undertaken by the federal government; and (4) an opinion by the Court outlawing excess spoil disposal in intermittent and perennial streams.

Jan 1, 2001

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By Chris Larsen, Ian Orford, Marilene Renaud, Mike Cooper, Lud Strah

"An AG/SAG mill was commissioned at the Brunswick Mine concentrator in October 1998. This paper discusses the original liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits. The mill liners consist of steel top hat shell liners, steel end liners, rubber grates and rubber lined pulp lifters.Lifter profile and plate thickness measurements were made on monthly shop days. Trends of wear rates were used to project when liners required replacement. Wear profile information was also used to determine where liner re-design would improve wear life or minimize scrap loss. Charge motion simulation modeling was used as a tool to assist liner design modifications.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large underground lead/zinc mine with a nominal production rate of 10,000 tonnes per day. The Brunswick concentrator commenced operation in 1964 with conventional surface crushing followed by rod and ball milling to reduce run of mine ore to the required size to feed two parallel flotation circuits. In 1998 the AG (autogenous grinding) mill was commissioned for a nominal production rate of 9,000 tonnes per day replacing two surface crushing plants, three rod mills and three primary ball mills. In May of 1999 the mining rate was increased and the service of the AG mill was changed to a SAG (semi-autogenous grinding) mill with the addition of 4 inch steel balls (4% volume). The mill operates in closed circuit with 0.66 meter horizontal cyclones to produce a ground product of 90 micron nominal size (K80).The AG/SAG mill liners are steel (Norsteel, chrome-moly steel) with rubber grates and rubber lined pulp lifters.The original liner design was based on studying other AG/SAG mills and recommendations by the liner supplier, Norcast. Design factors taken into account were total cost of lining (including material and labour), protection of mill shell and impact on operating performance."

Jan 1, 2003

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By S. Z. Pethö

Pillar extraction at shallow depths with small pillars that were not originally intended for secondary extraction can provide a huge benefit to the coal mining industry in those areas where a significant percentage of the remaining coal reserves are locked up in small pillars at shallow depths and where opencast mining methods are simply not as cost-effective and practical to implement. A system considering all of the pertinent geotechnical and mining aspects for the safe and efficient pillar extraction of small pillars at shallow depths at Xstrata Coal South Africa (XCSA) has been further developed and implemented as part of an ongoing improvement process addressing all of the relevant legal and associated risk aspects. This work follows on from the previous pillar extraction work carried out at the ATC, Boschmans, and Spitzkop Collieries. The process involved a number of in-house workshops and sessions arranged with all key personnel from Tavistock Colliery, and also included Professor Nielen van der Merwe of the University of the Witwatersrand, a world renowned authority on pillar extraction, towards reviewing and developing the Modified NEVID pillar extraction system employed previously at Boschmans Colliery. The system is currently being employed at Tavistock Colliery with success and no major accidents, with around 655 000 t of coal having been successfully extracted from the pillar extraction panels.

Jan 1, 2012

By I. T. Oramah

Despite the abundance of solid mineral deposits, Nigeria only earns about 0.5-1% of its current Gross Domestic Product (GDP) from the solid minerals sector. This is as a result of the dominance of the oil and gas industry, which has negatively affected the competitiveness of other sectors of Nigeria’s economy. The dominance of this industry has resulted in unemployment, poverty, hunger, domestic price inflation, corruption, unstable government, and higher exchange rates. These impacts are typical for economies suffering from the effects of "Dutch Disease" and the "Resource Curse". Community-based small-scale mining offers hope as an economic activity that can create wealth, employment, reduce hunger and poverty, and provide basic amenities for rural communities with solid minerals endowment. This study presents preliminary results of ongoing research into the prospects of using community-based small-scale mining in a developing country like Nigeria to move towards rural sustainable development.

Jan 1, 2011

In its April 1991 issue, MINING ENGINEERING published a salary survey form asking for information relating to engineering and management jobs in the minerals industry. 1038 of these forms were filled out and returned, most of them being received in the magazine's offices at SME headquarters before the end of June 1991. An SME volunteer took on the task of tabulating and analyzing data from the forms, but the press of other business interfered with this work, and publication has been delayed until this issue of MINING ENGINEERING. Appreciation is extended to SME members who took the time to fill out and return the salary survey forms, and our apologies go to MINING ENGINEERING'S readers for the delay in publication. Of the total number of forms received, more than 97% were from SME members. The geographic distribution of the respondents closely mirrored that of SME membership as a whole, about 50% being from the Society's Western Region, 19% from the Central Region, and 23% from the Eastern Region. About 8% were from outside the US. Average salaries for each of the four geographic areas ranged between $55,000 and $60,000, with the highest average in Eastern Region (Fig. 1). Respondents were asked to answer a number of questions formulated to determine if there are significant differences in salaries based on the type of organization for which they work. As indicated by Table 1, salary averages at mining companies do not vary markedly with the size of the company: • Large companies, defined as those having more than $1 billion in annual sales, accounted for just over 16% of the returns. Their average salary was $61,840 per year.

Jan 1, 1992

This paper outlines the complete failure of the U.S. in status and relevance in Rare Earth Oxides (REO). Although rare earth oxides are strategic and critical in their own right, refining these REOs into elements and alloys is even more important for the development of "Green Technologies" and advanced weapons systems. America does not have an active domestic source of rare earth oxides. America does not have any heavy rare earth elemental or alloy capabilities. The magnitude of this failure continues to become more apparent as the manufacture of REO based electronics and magnetic components moves eastward towards China. China has succeeded in outmaneuvering the United States and the world in its quest to control the rare earth oxides, elements and alloys, and the many industries dependent upon REO. What can be done?

Jan 1, 2010