Search Documents

By Thomas O. Meyer

Laboratory test results are presented for the determination of elastic modulus made with the NX borehole jack. Determinations were made in massive pieces of aluminum so as to satisfy conditions of linear elasticity, homogeneity, and isotropy. Results indicate a large discrepancy (approximately 200 percent) betwen material modulus as determined by laboratory block-loading tests and that indicated by the jack under relatively ideal circumstances. Effects due to interface friction, finite block size, incomplete plate-bore contact, and other factors were examined and found not to be significant. Finite element results indicate that assumed loading conditions for the jack differ from those actually occurring, at least in materials of high elastic modulus (approximately 10 million psi), such as quartzite.

Jan 1, 1974

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

The history of zinc production in Australia is outlined including attempts to make zinc electrolytically at Cockle Creek, N.S.W. in the last century, the use of horizontal retorts at Cockle Creek and Port Pirie, South Australia, production by electrolysis at Risdon, Tasmania and at Port Pirie using zinc oxide fumed from lead blast furnace slag and production by the Imperial Smelting process at Cockle Creek. Developments in the electrolytic process are described including those in roasting, acid manufacture, leaching, purification, electrolysis, melting and casting. The Imperial Smelting process technology is also outlined. In both processes global technology is reviewed, including important Australian contributions.

Jan 1, 1986

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930

By David J. Lowell

The gold content of porphyry copper deposits ranges from less than 0.05 g/t to more than I g/t ((0.0017 to 0.035 oz per st) and the average is about 0.05 g/t (0.0017 oz per st) gold. Perhaps the highest grade mineralization found near a porphyry cop¬per deposit is the Ok Tedi Gold Cap ore body whose grade falls in the 2 to 3 g/t (0.07 to 0.1 oz per st) range. It is difficult to define a gold-rich por¬phyry copper deposit. All porphyry copper ore bodies contain some gold, but there seems to be a fairly sharp break in the gold content at about 0.1 g/t (0.003 oz per st) gold. There is also a problem in identifying dis¬seminated gold deposits that may have an indirect relationship to porphyry copper systems. This relationship is clear cut in deposits such as the Ok Tedi Gold Cap, the El Hueso deposit, the Fortitude and West de¬posits at Battle Mountain, NV, and the Sur¬prise deposit at Ely, NV. There are many other bulk disseminated, epithermal-type gold deposits - McCoy, NV, for example - that might be related to a porphyry system but where this relationship is remains very uncertain. In such places as the Goldfields and Tonapah district in Ne¬vada and in the El Indio, Chile district, there may be a vertically stacked ore deposit rela¬tionship between near surface epithermal deposits and disseminated molybdenite and chalcopyrite enargite mineralization at depth that may represent a deep porphyry system. This, however, has not been positively demonstrated. Most of the bulk epithermal gold deposits are probably not related to porphyry copper systems. Exceptions would probably be Ok Tedi, El Indio, El Hueso, Battle Mountain, and Lepanto where vertical or lateral zoning relationships are more apparent. This author believes that porphyry copper systems are related to a relatively unique type of intrusion that is probably distinct from, for example, the McCoy intrusivebody. For that reason, deposits such as McCoy, Chimney Creek, and the like will not be included in the definition of gold-rich por¬phyry copper deposits for this article. The interpretation of the origin of several of the deposits previously mentioned are subject to an unusual amount of contro¬versy. For example, geologists seem to be equally divided about the presence of a porphyry copper deposit below the El Indio deposit. Geologic setting Continental vs. island arc Several geologists have speculated that the gold-rich, moly-poor, porphyries are

Jan 1, 1989

Commercially interesting deposits of zeolite rich tuffs and amorphous silica have been discovered recently in the Taupo Volcanic Zone (TVZ), North Island, New Zealand. This paper reviews them and comments on the potential for further discoveries. Potential markets for these unusual industrial minerals are discussed.

Jan 1, 1997

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"During 2000 Mintek Developed the PlantStar plant wide control platform for the minerals processing industry. The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.Processes with long dead times, like a feed belt to a mill, are difficult to control. The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.Often there are more variables on a plant that need to be controlled (process variables) than there are variables to control them with (manipulated variables). Process constraints are often reached and violated. Safety control loops are necessary to prevent constraints being reached. The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. It continuously perturb the solids feed rate to learn ‘where’ on the curve the mill ‘was’ and then to drive it continuously toward the middle, maximum power drawn. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads by cutting the solids feed to a minimum if the power drop below a specified threshold. Once the power rises above the threshold the solids feed is increased again to an intermediate value from where it start the perturbations again to find the maximum. This makes the milling circuit easier to operate."

Jan 1, 2003

By Xing Jin, Dan Graffi, Glenn MacPherson, Dan Rioux

"The complexity of a modern flotation circuit makes it susceptible to disturbances such as changes in feed, ore mineralogy, equipment degradation, poor measurements and faulty instruments. Good measurements and a robust control system are critical to create and maintain a stable and optimum flotation process.This paper focuses on the development and implementation of process control applications in the flotation circuits at Xstrata Nickel’s Strathcona Mill ( referred to as the mill hereafter ) in Sudbury, Ontario. Following the path of ‘stabilize-improve-optimize’, basic controls to stabilize process variables such as flotation cell pulp level, air and reagent addition rates, cleaning-column feed and wash-water rates have been established. Factors such as best practice in pulp level and valve position measurement, feedforward control and the application of an appropriate control philosophy, have contributed to the significant reduction in process variability. For instance, standard deviation reduction of 79% for the Ni impurity in the column Cu concentrate grade was experienced and is shown. The variability reduction of the flotation circuits’ key process-variables paves the way to further improve and optimize flotation performance. A grams-per-metal unit reagent addition control scheme has been improved upon, particularly for different operating scenarios and better robustness. In addition, following significant stabilization of the primary controls and columns feedrates, Cu/Ni separation cleaning-column bias-control (cascaded to the wash-water rate) and hold-up control (cascaded to air flowrate) have been developed and tested. This strategy – from stabilization to optimization - is expected to achieve a more consistent control of final concentrate grades and improve recoveries.INTRODUCTIONFlotation is considered the most important and value-added process in the milling metallurgical plant and is still undergoing continuous evolution to treat greater tonnage and different ores (Wills, 2006). Starting over three decades ago, with the advent of on-line slurry content analysis devices, flotation automatic control has received persistent interest and a large number of applications have been reported (Thwaites, 1983, 1986 ; Mckee, 1991). Bergh and Yianatos (2011) reviewed different aspects of process control in flotation circuits and have evaluated the applicability of model predictive control to the process. Mckee (1991) analyzed the difficulty in developing lasting/robust process control applications for flotation circuits and stated that the path of stabilization-refinement-optimization would more likely lead to successful flotation circuit process control. Best practice on column process control was discussed by Bouchard, etc. where a multi-layered approach was proposed, provided that the measurement of column process variables ( i.e. bias, froth depth, hold-up, etc. ) are measured reliably (Bouchard & Thwaites, 2008). Wills (2006) stated that the best practice for flotation automatic control starts with fulfilling basic control objectives, such as stabilized flotation cell level, air flow, pH, reagent flow etc., before considering more advanced, or even optimal, control of metallurgical targets, which are more closely linked to economic performance."

Jan 1, 2013

By N. Seidle

Numerous studies conducted in the 1960's and 1970's concluded or implied (1) that a high accident rate in terms of severity and frequency exists among new (first year) operators of mine machinery equipment, and (2) that lack of experience and training is a major cause of this high accident rate. Further studies refined this premise to show that the major causes of accidents among first year operators are: (1) lack of manipulative skills; (2) failure to follow/adhere to routine procedures; and (3) failure to recognize and respond properly to hazards. This report describes the design, development, and manufacture of a shuttle car operator training system, including a program of instruction which: ? Is economically feasible. ? Addresses accident data and specific causes of accidents. ? Includes an aerospace quality simulator of sufficient fidelity to teach and develop manipulative skills, recognition of and response to hazards, and routine and emergency procedures. ? Is designed to significantly reduce the severity and frequency of accidents especially during the operator's first year. ? Is designed to significantly improve the performance of the trainee as compared to the standard learning curve. Development of the simulator produced several valuable by-products including a major state-of-the-art technological advance in visual systems for simulators, and a first-time application of (certain) advanced filming techniques to underground filming.

Jan 1, 1984

By Johan F. W. Kock

"Hearing loss due to excessive noise exposure is the most prevalent industrial disease. It is ranked on the World Health Organization’s (WHO) priority list for major work related injuries. Uncontrolled noise not only has a physical effect, but is also a psychological hazard affecting the performance and well being of man. Noise induced hearing loss (NIHL) is irreversible, yet it is preventable. The first defence against noise (noise control engineering) is a high priority in the mining industry. Second defences should be a last resort when the engineering control of noise is inadequate. Hearing conservation programs and the use of conventional hearing protection devices seem to have failed in the prevention of noise induced hearing loss. If compensation payouts that quadrupled in the past ten years are used as a barometer for the success of existing hearing conservation programs, then new strategies and technologies need to be investigated. The best practice Hearing Protection Device (HPD) may be seen as the minimum standard for second defence noise control.Conventional hearing protection is widely applied, but also misused in the industry as well as in the mining sector. Empirical research results, ownership, general attitudes of workers as well as qualitative aspects will be explored. The paper provides reasons, evidence, case studies and strategies regarding the best practice hearing protection philosophy (the Noise Clipper Model) as implemented in the Implats Mining Group. Worldwide tendencies towards custom-made HPD’s, findings that indicate improvements in hearing conservation programs and finally the successful application of Custom-made Hearing Protection Devices, will be outlined."

Jan 1, 2003

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

By Paul Armstrong

THE first discovery of lead and zinc ore on Calumet island was made in 1893 by John Lawn, who then staked a portion of the property now owned by Calumet Mines, Limited. His discovery was developed by James and Calvin Russell, who are said to have shipped a few tons of sorted ore, averaging 39 per cent zinc, 13 per cent lead, and 11 oz. silver per ton. In 1898, the property was being operated by the Grand Calumet Mining Company, who mined and shipped, for treatment in a Belgian smelter, 1,100 tons of ore averaging 32 per cent zinc, 9 per cent lead, and an unreported content of gold and silver. After some indecisive exploration by an American syndicate in 1907, the property lay idle until1910, when the Calumet Metals Company-later reorganized as the Calumet Zinc and Lead Company-re-commenced exploration. After sinking an 85-foot shaft-the McDonald shaft-and doing a few hundred feet of drifting and cross-cutting, this Company, in 1912, erected a 150-ton daily capacity gravity-concentration plant, in which some 800 tons of ore, mined from the McDonald shaft and Bowie pit, were milled. Owing to very disappointing mill recoveries, the property was shut clown and-after several years of idleness-in? 1916 the mill and mining plant were destroyed by fire and the Company went into bankruptcy. In 1918, an unknown operator shipped to an Omaha, Nebraska, smelter 22 tons of ore, probably sorted from the dumps of the Ste. Anne shaft and Galena pits, averaging 44 percent lead, and 0.26 oz. gold and 61 oz. silver per ton. The British Metals Corporation (Canada), Limited, in 1926, optioned the property. They unwatered the McDonald shaft and, after doing an additional 300 feet of cross-cutting and drifting on the 85-ft. level, estimated there were some 33,000 tons of ore between this level and the surface. Surface exploration, including trenching, on other showings on the property gave discouraging results and the option was dropped.

Jan 1, 1941

By Wilhelm Borchers

IN all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity . towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly growing number of inventions, inasmuch as the chief con¬stituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity fir those elements which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to beat the refining-slag to the highest point of its chemical activity ; to prevent the iron from entering the slaw, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1910

By S. T. Johansen, C. Colomb, B. Ravary

Combustion and thermal NOx formation have been modelled using the Computational Fluid Dynamics (CFD) commercial code Fluent 6.1. The aim was to predict and give a better understanding of the combustion in electric arc furnaces for the production of ferro-silicon and silicon metal. Another important objective was to assess the impact of a number of operating parameters on the NOx formation. The CFD tools used are de-scribed with a special focus on models for species and turbulence transport. Sensitivity studies have been carried out to study the influence of several parameters: sub-models, process gas composition and distribution at the charge surface and influence of the presence of SiO. The main conclusions are: ?Using the combination of a realistic design, boundary conditions and models, the simulated NOx level is in quantitative agreement with measurements. The presence of water vapor is particularly important because of its influence on the specific heat of the mixture and resulting temperature. ?Release of significant amounts of SiO from the charge surface results in an important increase of NOx, even if we applied a simplified combustion model for SiO gas. However, because of lack of thermal and compositional data for blowing situations (when SiO flows directly from the arc cavity through open channels to the charge surface), no quantitative validation is possible. The way SiO is distributed (uniformly or as a jet) has a limited impact on the result in our computations.

Jan 1, 2007

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981