Search Documents

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By Anil Mahyera

This report present the results of a laboratory and field research program aimed at design and development of a torque-thrust controlled bolter with the capability to (1) predict the "quality of anchorage" attained while installing mechanical anchor roofbolts, and (2) improve the uniformity and tension levels achieved among a group of roofbolts. The prediction accuracy of the anchorage quality algorithm ranged from low to moderate because of the complexity and variability of the phenomena involved. The best roof support with mechanical anchor bolts was found to be achieved by simply installing them under ? proper torque-thrust control, and with ? a hardened washer under the bolthead. This procedure resulted in an improvement in uniformity of 3 times, along with an increase in mean tension levels of 75% over conventionally installed roofbolts.

Jan 1, 1983

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

The following brief paper is intended, to apply to the concentration of the silver-lead ores at Broken Hill, New South Wales, generally, but more particularly to the process as applied to the ores in the Block 10 mine. The attached plans are similar inmany respects to those prepared, recently for the Block 10 company.Most of the information here given is already well known to those members who are conversant with the concentration practices of this field, but it is the writer's object to give just a few of those figures which he found difficult to obtain when first engaging in practical work. At that time no text-books were at hand from which it was possible to get sufficient details for practical working purposes.It is first supposed that the mine has been thoroughly explored and has been found to contain a lbde sufficient in size ·and quality to warrant the erection of a concentrating plant. The points then to determine are:-(1.) The quantity and cost of water available for steam-making and ore-dressing purposes.(2.) The most convenient site for the mill.

Jan 1, 1904

By Alfred Weiss

At the end of the first decade of digital computing in the minerals industry, geostatistics in North America was still in its infancy. This was in contrast with the rest of the world where the technique of kriging was already widely practiced. By the end of the 1970s, there was increasing awareness among practitioners of its potential. But it was not until the late 1980s that geostatistics was universally applied and accepted. This was due, in large measure, to contributors at Applications of Computers and Operations Research in the Minerals Industry (APCOM) symposia. Such an evolution in new computer methods could again be observed at APCOM 26.

Jan 1, 1996

The zinc-lead lode at Rosebery, on the West coast of Tasmania, has a total length of over 4000 ft. It consists of five elongated lenses parallel to the foliation planes of the quartz sericite schist, and is situated at the junction of the quartz sericite schist and a thin belt of slate. The lenses consist of massive, fine grained sulphide ore, with small amounts of quartz, barite, sericite and chlorite, and they terminate in masses of low grade ore. The gangue minerals increase in quantity in the low grade ore which includes small quantities of the manganese garnet, spessartite. The schist walls of the lenses are in places impregnated with lode minerals to a degree sufficient to permit them to be regarded as economic ore.The ore-bodies have developed from incoming mineral solutions by the replacement of the quartz sericite schist and are localised where the ore solutions have been confined by a relatively impervious slate band. The early stages of replacement of the schists are signified by the development of pyritic bands which are succeeded by a strong development of zinc blende. With ptogressive crystallisation, the character of the mineral solutions gradually changed and the development of galena, and its associated bournonite, became more important in the later stages.Remnants of the replaced schist, in the form of isolated wisps and schlieren of sericite and chlorite, are present in the ore body, more noticeably in the pyritic specimens. An important feature of the ore is the association of small ogllantities of gold with trahedrite.

Jan 1, 1934

By Susan P. Taite, Alain R. Charest, Peter D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in the southwestern Chihuahua state of Mexico (Fig. 1). A Francisco Gold geologist discovered the prospect in1995. El Sauzal was encountered as a result of an extensive grassroots exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas silver camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiaryage. The mineralization appears tobe structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system, including kaolinite, illite, alunite, dickite and pyrophyllite.

Jan 1, 2005

The Kingsgate molybdenite pipes are considered on petrochemical data and field occurrence to be, possibly, epi-magmatic plutonic offshoots grading into hydrothermal bodies. There is reason to believe that the ore is derived from a highly acid granite of type similar to that of the tin bearing areas of northern New England. The mineralogy, microtextures and paragenesis of the ore are discussed.INTRODUCTIONThe Kingsgate Mining Field is situated in steep, heavily timbered terrain 18 miles E.N.E. of Glen Innes and 430 miles north of Sydney. Bismuth and molybdenum ores were discovered at Kingsgate (Yarrow Creek) in 1877. Subsequently some 50 pipes were developed yielding tonnages which at the peak of operations, 1905 to 1920, rivalled production from the rich deposits of northern Queensland.Attempts to revive the field have been made periodically and small parcels of ore have been forthcoming.' During World War II demand for piezioelectric quartz again focussed attention on Kingsgate but twinning and other imperfections of the quartz prevented all but a minor exploitation of the otherwise noteworthy crystals of this locality.There is reason to believe that the ore at Kingsgate is not exhausted through exploration and mining costs would probably be high due to the capricious nature of the pipes and to the irregular distribution of rich ore shoots within them.

Jan 1, 1962

By Dennis E. Mitchell

The need to develop and field explosive, pyrotechnic and propellant initiating systems that have high reliability and extraordinary safety requirements has led to the exploration and development of several materials and initiation systems at our laboratories. Our approach to initiating device development encompasses five main areas; energetic materials development , device physics, theoretical analysis and model development and experimental verifications

Jan 1, 1995

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By N. Simpson

Low carbon 11.5% chromium stainless steels are finding increasing use in industry as square or rectangular tubing material for the construction of structures by welding. During processing, resistively welded circular pipes are bent into square or rectangular shapes. During this process longitudinal cracks can sometimes develop atone of the inner corners of the section. An investigation has shown that the processing of round into square tubing with very sharp corners can cause excessive cold working at the inner corners of the squared tube. This, together with the high tensile residual stresses and a susceptible microstructure due to the presence of grain boundary carbides, can result in brittle cleavage cracking. Measures that can be used to reduce the problem are described.

Jan 1, 2003

By B. McNulty

The Niblack polymetallic volcanogenic massive sulfide deposits are located on Prince of Wales Island in southeast Alaska, approximately 50 km southwest of Ketchikan. The property hosts a number of polymetallic volcanogenic sulfide occurrences within the folded Lookout rhyolite volcanic succession. The Lookout deposit is the primary focus of current resource delineation and contains an indicated resource of 4,136,000 tonnes at 1.13% Cu, 2.32 g/t Au, 2.27% Zn, 38.70 g/t Ag and an inferred resource of 1,736,000 tonnes at 1.09% Cu, 1.77 g/t Au, 2.02% Zn, and 25.52 g/t Ag as of March 2011. Sulfide mineralization is interpreted to have formed sub-seafloor, within permeable felsic fragmental volcanic rocks. Sulfide minerals of economic interest include chalcopyrite and Fe-poor, Zn-rich sphalerite. Of considerable importance, the Lookout deposit contains elevated gold that occurs as inclusions within the base metal sulfides.

Jan 1, 2012

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By Fidelis T. Suorineni

Rockbursts are a major hazard in deep hard rock underground mining and tunneling. To date a significant number of rockbursts still defy conventional explanations. A review of rockburst case histories in the literature has shown that pillars and tabular excavations under shear loading are prone to rockbursting in situations where they are least expected under conventional knowledge of rockburst causes. Despite the evidence of the effects of shear loading on underground infrastructure, and the frequency of their occurrence, little is known about how this loading mechanism causes such large magnitude events and extensive damage. In this paper analytical and numerical modeling are used to understand the behaviour of pillars and tabular excavations under shear loading. The numerical modelling results show that pillars under shear loading are less confined than their equivalents in loaded in pure compression in the same geologic environment, and are therefore more brittle and weak. For tabular excavations under shear loading, the behaviour depends on whether such excavations are continuous, co-planar or offset with rock bridges. Analytical results based on slit theory show releasable potential energy in tabular excavations increases nonlinearly with excavation half-span. The study results are important for the safe and economic extraction of orebodies under shear loading.

May 1, 2011

By Noel N. Moebs

Bureau of Mines studies of mine roof fall problem in the Pocahontas No. 3 Coalbed of southern West Virgania and southwestern Virginia have established that type and sequence of rock are significant factors in roof competence. The poorest conditions occur where the immediate roof consists of slump structures and slickensided rock. The best conditions occur where the roof consists of a sequence that coarsens upward from shale to massive sandy shale. A small manual of color photographs of rock types was devised to aid in identifying drill cores. Proper identifications should enhance the prediction of areas of potential roof problems in advance of mining.

Jan 1, 1981

By F. A. Patty

[Health and safety hazards from contamination of the atmosphere in places frequented by persons depend to a considerable extent on whether the contaminating agent possesses sense-perceptive properties which will give warning of its presence before it '.an create harmful conditions. If a distinct and easily recognized warning is given in advance of harmful conditions, hazards ace mitigated, but if warning properties are inadequate or absent, the hazards are augmented. When evaluating the hazard presented by a potentially harmful substance used under conditions of possible escape into the air of places frequented by persons, it is therefore necessary to consider the warning properties of the substance along with ether pertinent information such as toxicity, inflammability, physical properties, and mode of use. If the contaminating agent inherently lacks warning; properties it may be possible to impart them by adding to the hazardous substance a small quantity of a relatively harmless substance which has a high warning intensity.]

Jan 1, 1929

By G. W. Harris, J. J. K. Daemen

Slightly shorter, modified version also published in CIM Bull., vol.94, no.1047, Feb. 2001, p.52-55. To minimise ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will allow more accurate location of the grade boundaries on the surface of a blasted rock pile before excavation. A method has been developed and tested for measuring accurately the direction and magnitude of subsurface blast movement, using a caesium vapour gradiometer and a real-time, differentially corrected global positioning system to locate the pre- and post-blast positions of magnetically enhanced target objects placed in blastholes inside a bench. The procedure does not necessitate disturbance of the blasted rock and the movement information is available sufficiently quickly to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m and the overall accuracy was plus or minus 1 m horizontally and 1.2 m vertically

Jun 21, 1905