Search Documents

By Peddie F, Low K, Madgwick J, Rajoka M. I, Gutierrez N, Lim C

Percolation irrigation of low-grade quartz feldspar porphyry ore with pH 2.0 H2SO4 at 510 litres/m2/day using particle sizes 1.7 - 6.7 mm in columns measuring 5 cm dia × 126 cm long was used to study effects of interrupted irrigation ('rest' periods) on metal ion release and leaching bacteria. Copper tenors increased approximately 16 fold and bacterial iron oxidation activity three fold following a 14 day 'rest'. A linear relationship between copper tenor and bacterial activity demonstrated that this experimental system was effective for quantitative studies of bacterial leaching in ore colums.

Jan 1, 1981

By L. V. Clark, Arthur La Motte

"INTRODUCTION The U. S. Bureau of Mines in 1930 and 1931 made a study of the properties and characteristics of liquid-oxygen explosives (L.O.X.) at the request of one of the largest users, in order to determine and eliminate the hazards attending its use.This report deals with the examination of absorbents for L.O.X. to (1) determine their most desirable and most undesirable characteristics, (2) to find ways and means of desensitizing absorbents to mechanical shock, and (3) to determine the effect that such desensitization of absorbents has on the explosive Characteristics of L.O.X.ABSORBENT MATERIALS The absorbent used in driving the Simplon Tunnel, the earliest project in which L.O.X. was used, was composed of crude petroleum, soot, and kieselguhr. During the World War, powdered cork, soot, sawdust, powdered straw, or other similar powdered materials were mentioned in the German military instructions for use of ""liquid air"" explosives. At that time the common types of absorbent, materials were compounded ones containing the above ingredients as well as kieselguhr, paraffin, gas oils, charcoal, bituminous coal, etc.Kuryla and Clevenger4 investigated absorbents of the above type and made the following statement concerning them:"

Apr 1, 1932

By Y X. Xue, J Pan, D Q. Zhu

In order to reveal the correlation between the fundamental sintering characteristics of iron ores and their real sintering behaviours, a comprehensive evaluation index is proposed based on the measurement of four high temperature indexes, ie assimilation temperature, liquid phase bonding strength, liquid fluidity and calcium ferrite formation percentage, and the sintering pot tests of single ore fines and their blends. The results show that both the lowest assimilation temperature and liquid fluidity of ore blends appear to be the linear superposition of those of single iron ores except for the liquid phase bonding strength and calcium ferrite formation percentage. Furthermore, the tumble index of the sinter product obtained from blended iron ores also corresponds to a linear superposition of that of single ores, but not for the solid fuel rate and productivity. The comprehensive strength index YT exhibits a credible linear positive correlation with the four high temperature reactivity indexes, whereas the comprehensive productivity index YP possesses a lower correlation with the four high temperature reactivity indexes. The comprehensive strength index YT developed can predict the tumble index of the sinter product quite well, but the comprehensive productivity index YP cannot be used to evaluate the productivity effectively.CITATION:Zhu, D Q, Xue, Y X, Pan, J and Shi, B J, 2017. Correlation between high temperature sintering characteristics and sintering behaviours of iron ore fines, in Proceedings Iron Ore 2017, pp 123–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35°C to 90°C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0·75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017

By P. J. Knottenbelt

Outcomes from a workshop organized through the SAIMM revealed that the minerals and metals industry must develop its ?Engineering Team? if it is to continue to meet the challenges of globalization. The very economy of the country is largely dependent on a competitive and stable engineering team within the minerals and metals sector. With the Chamber of Mines (COM) passing on its education and training initiatives to the industry, the professional bodies like SAIMM must (despite meagre resources) continue the good work done through the COM in the past. The workshop highlighted recruitment and selection, further/higher education, socialization and initial training, deployment and retention and continuing education as priority areas. These are further detailed in this report. Office Bearers have considered the outcomes and the areas where the Institute should or should not be involved have been stated.

Jan 1, 2002

By T F. Guerin

Explorationn and mining have shown to cause significant impacts to the terrestrial and marine environment. Current mining and exploration techniques are outlined in the light of their potential to impact upon the environment, ie negligibly, negatively or positively. A profile of five Australian-based gold producers is presented. The development of protocols to specifically deal with the highly regulated and ever changing, mining and environmental legislation. demonstrates mining companies can successfully opcrationalise the concept of sustainable development.

Jan 1, 1992

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By E Deucker, A White

Gold Fields Australia (Gold Fields) has identified that improving productivity through more detailed shift planning and operational control of mining activities is a key driver to the success of their business. The Hamlet mine was chosen as a pilot site to trial a system that would allow production engineers and shift bosses to align the execution of short-term activities with the longer-term goals of the organisation.Gold Fields partnered with Deswik to introduce an on-site, collaborative, web-based system to allow mine planners to quickly build-up a detailed, activity-based, shift schedule for the coming week from the 13-week plan. Multiple stakeholders could then review and alter the plan, and then track and manage the execution of the activities.The system is designed to be integrated with production data capture systems to allow tracking of progress towards completion for each activity, as well as to plan and monitor the equipment operating in the mine. Integration of systems allowed engineers to use the large quantities of production data being captured to make informed decisions in the operations environment.The system replaced a complex set of spreadsheets that required expert users in Gold Fields to maintain. By capturing the data in a central database, the planning process is transparent and historic data from the execution of activities is available for analysis to improve productivity in the future.The system has ensured that the highest priority and critical path activities for the business are completed at the right time, improving the efficiency of operations.CITATION:Deucker, E and White, A, 2017. Productivity improvement through collaborative shift planning and tracking, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 225–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

Acoustic Emission Monitoring of Froth Flotation

Sep 13, 2010

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By J. Gunaselvam

This article deals with an investigation into the specification and use of appropriate seating systems to reduce whole-body vibration (WBV) exposure in typical vehicles used in the SA mining industry. The EU Directive EU/44/2002 to be legislated in 2005 in European countries, provides legal and economic motivation for this project. The criteria for seat selection can be condensed to the requirements in the directive, which mandates an action level of 0.5 m/s2and a vibration exposure limit of 1.15 m/s2 for an equivalent 8-hour daily exposure period. As part of this study six suspension seats, which the manufacturers claim satisfy the requirements in ISO 70966, were tested to determine the most suitable seat for an articulated dump truck. Six test subjects, three ?light? and three ?heavy? as specified in ISO 70966, were used to estimate the seat transmissibility functions in the vertical direction of the six different suspension seats. Transmissibility functions were measured in the laboratory with two excitation levels of 1 m/s2 and 2 m/s2 r.m.s. in the 0.5?30 Hz frequency range, as well as one spectrum approximating the EM5 spectral class. SEAT values were calculated for road vibration data measured on a typical articulated dump truck. A set of seat selection guidelines that can be followed by vehicle manufacturers and suppliers, procurement officers and and the technical staff on a mine is proposed in this article. It is recommended that additional studies of the use and operating conditions of seating systems in the SA industry, as well as an epidemiological survey be commissioned to gather additional information on this subject. Nomenclature ADT Articulated dump truck DSTF Dynamic seat testing facility EM1 Frequency spectra associated with earth moving equipment (?articulated or rigid frame dumper?) according to ISO 7096 EU European Union ISO International Standards Organisation PSD Power spectral density r.m.s .Root mean square SEAT Seat effective amplitude transmissibility WBV Whole-body vibration

Jan 1, 2005

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognized and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economic restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist about application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2007

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944