Search Documents

By J. H. Swisher

An experimental study has been made of the possible mechanisms for foam stability in the system CaO-SiO2-Cr2O3, where Cr2O3is the foaming agent. The degree of lowering of surface tension by Cr2O3 was determined at 1600 "C for high -silica melts. Measurements were also made of foam stability under standardized conditions. The results of the two sets of measurements then were correlated by applying the Gibbs and Marangoni theories of film elasticity. It was demonstrated that the Marangoni elasticity effect is probably the largest single contributor to foam stability, although the high uiscosity of' silicate melts makes some contribution in controlling the rate of drainage of liquid from bubble lamellae. ThE tendency of metallurgical slags to foam has frequently been observed during steel-refining operations. In the open-hearth furnace,this tendency is considered undesirable because it slows down the rate of heat transfer from the burners to the molten-metal bath. On the other hand, it is sometimes desirable to have a "foamy" slag in the basic oxygen converter.' A more effective blanket over the steel bath is made by a "foamy" slag, and loss in yield of metal due to splashing is minimized. In addition, a flush slag can be removed more easily in this condition. Since slag-foaming problems in the field have been attacked largely on an empirical basis, it appeared desirable to obtain a better basic understanding of the mechanism of foam stability. The experimental work was directed almost entirely toward the behavior of Cr2O3 as the foaming agent in CaO-SiO,-Cr2O3 melts. In the first stage of the investigation, the degree of lowering of surface tension by Cr2O3 was determined at 1600°C. The second stage consisted of measuring foam stabilities under standardized conditions. The two sets of experimental results then were correlated by applying various theories of foam stability. For convenience in interpreting the surface-tension and foam-stability results reported here, a portion of the CaO-SiO2-Cr2O3 phase diagram2 is reproduced in Fig. 1. EXPERIMENTAL 1) Surface-Tension Measurements. Very little information is available in the literature on the lowering of surface tension of slags by foaming agents. Kozakevitch 3 mentioned that the addition of 1.5 pct Cr2O3 lowered the surface tension of FeO slightly. In another system, some data on the lowering of surface tension of foaming slags by P2O5 were reported by Cooper and Kitchener.4 The technique used for the surface-tension measurements was the maximum bubble-pressure method,' using a single tube immersed to various depths in the melt. This method has been used extensively in high-temperature systems, such as in liquid metals, slags, and glasses.6,7 It has the advantage that the contact angle between the liquid and the tube material need not be known. The equation used for calculating surface-tension values from maximum bubble-pressure measurements is the Schroedinger equatioq5 which can be written as follows:

Jan 1, 1964

The paper examines the value of very small-scale indigenous gold mining operations to developing countries. The paper looks particularly at this type of activity in two neighbouring countries, Papua New Guinea and the Philippines, considering technical, economic, social and environmental aspects.

Jan 1, 1990

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022

By John A. Rusnak

"This paper discusses the variation of coal strength based on the megascopic coal lithotypes for Central Appalachian high-volatile A coal beds. The composition of coal beds is complex and variable, depending on the depositional environment associated with original plant material, inflow of clastic material, and water level fluctuations in the original swamp/mire environment. Thus, different types of coal and sediment are formed within each coal bed. These differences in coal composition were first classified by Marie Stopes, a paleobotanist, in 1919. The classic coal megascopic lithotypes are vitrain, clarain, and durain, which correspond to bright, bright banded, and dull coal, respectively. Stopes also identified that the lithotype fusain, which is mineral charcoal, has no inherent strength and can act as a plane of discontinuity. In this study, two other coal-bed lithologies are also considered—bone and carbonaceous shale. This makes for a comprehensive suite of coal-bed stratigraphic components apart from rock partings. A total of 1,000 uniaxial compressive strength (UCS) and 440 indirect tensile strength (ITS) tests were conducted on cores from southern West Virginia that were specifically logged and described using the megascopic coal lithotype nomenclature. Statistical analysis is presented showing the results for each lithotype group with mechanical properties correlated to the lithotype. Previous studies have analyzed the mechanical breakage properties associated with coal lithotypes, which correlate well with these results. However, coal rank does appear to be a contributing factor, and this study is confined to only high-volatile A bituminous rank. Application of these results would be well suited to a rock mass classification system to address coal pillar rib stability. This would allow for rib support design and implementation to consider relative coal strength by visual observation of the seam stratigraphy through ongoing observations within a mine. Changes in seam composition can be readily identified, allowing the adjustment in rib support design. Another application would be for the determination of numerical modeling inputs based on detailed seam stratigraphy. However, these results, even with the standard strength reduction criteria, may not be applicable to currently accepted empirical coal pillar design procedures."

Jan 1, 2017

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By J. Davis, M. G. Reading

"INTRODUCTIONInternational Minerals and Chemical Corporation (Canada) Limited operates two potash mine/refinery complexes near Esterhazy, Saskatchewan. Annual production of approximately 4.2 million tons is sold in the United States and overseas in five grades according to size and quality.Ore grading 25% K2 0 equivalent is mined from a horizontal bed by continuous boring machines, crushed, and hoisted at 8 inches. The refinery operation consists of the eight basic steps shown in Figure 1. Particle sizes handled are similar to those experienced in other forms of mineral beneficiation: 8 inches to 100 mesh. The ore is crystalline and particles are angular. Fortunately the major mineral constituents, sylvite (KCl) and halite (NaCl), demonstrate relatively low hardness at 2 to 2.5.Therefore, while simple abrasion must be acknowledged, it is not a major problem except, of course, in circuits carrying magnetite.Corrosion, as represented by the classic equations of Figure 2, occurs in all its various forms."

Jan 1, 1983

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By S McGregor, J Sharp, I Entezari, T Boulter

The piezocone penetration test (CPTu) is one of the primary screening tools used by the mining industry to evaluate whether tailings are susceptible to liquefaction (static or cyclic). Liquefaction analysis using the CPTu is influenced by the fines content of the soil, and most CPT screening tools empirically use the behaviour type index (Ic) to correct for fines. The issue with this approach is that such empirical relationships have been developed using data collected from natural soils and their applicability to different tailings deposits needs to be studied. In this paper, we explore the use of machine learning to develop a site-specific model to estimate fines content of tailings using gamma piezocone penetration testing (GCPTu) measurements. The results are then compared to the fines content derived from the soil behavior type index (Ic) proposed by Robertson and Wride (1998). A dataset of paired GCPTu and laboratory results were compiled and a support vector machine (SVM) algorithm was employed to calibrate a model to estimate tailings fines content from in-situ GCPTu data. We calibrated GCPTu data to geotechnical 75 μm fines content measured in the laboratory. The geotechnical fines content is the fines content as a percentage of solids. The development dataset was comprised of paired GCPTu-laboratory results collected in 2009-2019 from a mining area with predominately clay mineral and quartz sand tailings. Results show that the developed model predicts the geotechnical 75 μm fines content of the studied deposits with 7.8% error. The Ic based method estimates the fines content with 31% error. Evidently, the Ic method is not applicable to the studied tailings deposits. It is appreciated that many tailings fines do not contain clay, and that the success on this program may not be repeatable everywhere. However, the authors wish to point out that the application of site-specific machine learning algorithms may be used to significantly improve empirical geotechnical parameters.

Jul 1, 2021

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By M. Moseki

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy of Materials) degree This paper presents the research into melting of scrap for job creation purposes in rural areas. The research was done on behalf of Mine Recycling Services (MRS), the company that will implement the project. The project involves the research into available cost effective and easy to operate technology. The paper covers the experimental and theoretical work that was conducted. The results were used to determine the best equipment and method for melting and casting brass scrap.

Jan 1, 2002

"4.1. IntroductionThis chapter reviews the geochemistry of the platinum-group elements (POE) in sulphur-poor silicate rocks, and the limited data on POE in silicate, oxide, sulphide, arsenide and sulpharsenide minerals. The earliest geochemical studies of POE in silicate rocks, minerals and meteorites were carried out mainly by Goldschmidt, the Noddacks and their co-workers, and are reviewed in Crocket (1969). These researchers established the siderophile character of the POE, emphasized the common association of the group with sulphides in ultramafic-mafic rocks and suggested that very low concentrations of POE are typical of sulphur-poor silicate rocks and minerals. Much of these data were for Pt and Pd only and are more than 50 years old. Because of the poor sensitivity typical of the available analytical methods, few reliable data were obtained on silicate rocks in these early studies. Surveys of POE geochemistry demonstrate that the data base for sulphur-poor silicate rocks is very restricted, although considerable highquality data for Pd and Ir have been accumulated (Wright and Fleischer 1965, Yushko-Zakharova eta/., 1967, Mertie 1969, Crocket 1969, 1979, Keays 1981).Two recent publications, Vol. 71, No. 7 (1976), of Economic Geology (An Issue Devoted to Platinum-Group Elements) and Vol. 17, Part 2 (1979), of The Canadian Mineralogist (Nickel-Sulphide and Platinum-Group-Element Deposits), are of special interest. These volumes are clear testimony to the impressive progress made in the last decade toward describing the mineralogical and geochemical aspects of POE ore deposits, but at the same time demonstrate the constraints in modelling POE ore genesis due to our meager knowledge of the. POE content and distribution among minerals in the source rocks of ultramafic and mafic magmas. It is clear that the phases hosting POE in mantle source rocks are poorly understood. Nevertheless, Naldrett and Duke (1980) have shown that the absolute and relative concentrations of POE in magmatic sulphide ores are related to the degree of partial melting of mantle peridotites, and subsequent processes of batch equilibration and fractional segregation of sulphides."

Jan 1, 1979

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By Boden A

A procedure was developed for recovering metal values from copper-smelter fume. The fume is first leached to neutrality with dilute sulphuric acid to obtain a solution of zinc sulphate containing a low level of impurities. The tailings from this leach are treated with hydrochloric acid in two stages, in which tin and zinc are quantitatively leached and recovered as a tin concentrate and a zinc sulphatelzinc chloride solution.About 80 per cent of the lead sulphate is converted into lead chloride, which can be recovered as a pure product.Data on the effect of temperature, acid concentration, aeration, and solid/liquid ratios on the hydrochloric acid leach are presented, and the fate of the most important metals during the recovery process is described. Alternative treatments of the tailings from the neutral sulphuric acid leach were briefly investigated.

Jan 1, 1977

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By F. C. NINNIS

AT THE Belmont mill, the pregnant solution is de¬livered to a 30 by 10-ft. tank, from which it is pumped to three Merrill clarifying presses of the sluice-bar type, whence it flows through the meter to the precipitation supply tank. ?The solution for precipitation is pumped by a 10 by 10-in. Aldrich triplex pump and delivered through a 6-in. line to the forty-eight triangular frame Merrill presses at the head of the mill. Zinc dust is fed in at the pump suction and the solution precipitated to 0.01 to 0.02 oz. silver. The solution flowing from the presses is tested at 1-hr. intervals with sodium sulfide. All solution is precipitated to the same value; 4J tons of solution are precipitated for each ton of ore treated and the presses are cleaned every 15 days. The product from the presses' is dumped into steel cars having steam-jacketed bottoms, in which they are dried until the moisture content is between 15 and 17 per cent. when 8. per cent. of soda and .3 per cent. of borax are added and the contents thoroughly mixed. In the case of special clean-ups, the precipitate is tested and the flux is added to meet the requirements.

Jan 1, 1921