Search Documents

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

By Sharpe E. J

The Triton lode is a schistose feldspar biotite chlorite rock with quartz, carbonate, pyrite and some pyrrhotite. Its more chloritic sections strongly resemble the enclosing greenstones, its more feldspathic portions are indistinguishable from the flne-grained phases of the porphyry dyke into which the southern extremity of the ore body merges. The ore body' has a length of 880 ft. and an average width of I2t ft.; in places this widens to as much as 30 ft.The average dip is 85° west and pitch of the ore shoot 75° south.METHOD OF SAMPLING.With the exception of a limited amount of channel sampling (a reference to which is made elsewhere in this paper) all the sampling is by chip sample.The samplers use a hammer weighing approximately 11 lb. and chip directly into the sample bags. Sampling is generally carried out over 3-ft. sections and portions thereof to the nearest half foot-thus a face 8t ft. wide is divided up into two sections of 3 ft. each and one section of 2 ft.-no measurements of less than 4 ft. are used and calculations are all in feet and dwt. per long ton.In the oxidised stopes wp.ere the lode is much narrower, .i.e., 6 ft., sampling is over 2-ft. sections. All borehole samples are over 2-ft. sections, this corresponding approximately to steel changes.(a) DEVELOPMENT SAMPLING.Driving.-This is done by following the east wall and each face is sampled-this corresponding to an advance of 5 ft. If the full width o,f the lode is not exposed boreholes...

Jan 1, 1938

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By Daniel Mageau

Ground freezing has been used for over 100 years to provide shoring and ground water cutoffs for hundreds of projects worldwide, including drilled shafts, tunnels and cofferdams. Typically, these cases involved difficult soil/water problems where ground freezing was likely the only solution. This paper discusses a recent ground freezing project where a frozen soil wall was used for a more conventional problem. A 4-foot-thick frozen soil wall was used to provide shoring and groundwater cutoff for a 20-foot-deep excavation during construction of a cast-in-place concrete storm water detention vault. The site is located along the northbound on-ramp to I405 from westbound SR522 in Woodinville, Washington. The frozen soil wall was successfully formed in soils consisting of till fill over soft organic silt and loose saturated sand in about 3 weeks. The depth to ground water varied from about 4 to 8 feet over the site. The unfrozen soil inside the frozen soil wall was excavated vertically to the frozen soil boundary. The vertical excavation remained open for approximately 2 months with no dewatering required. On one side, fully-loaded dump trucks and other construction equipment operated within 6 feet of the wall face with zero wall movement. This paper addresses the construction issues related to installation and operation of ground freezing shoring. The overall wall performance of the frozen soil wall as well as basic geotechnical design issues are also discussed.

Jan 1, 1998

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By Gerald Blackmore

"This paper suggests that with the settlement of long-term contracts of fifteen years' duration, with prospects of extension, the coal mining industry has, for the first time, a complete commercial justification for large-scale planning.The labour costs of coal production over past years are analyzed and, with the acceptance of the premise that the basic shift rates are certain to rise in the years to come, the paper suggests that forward planning should provide &r capital investment to make a traditionally labour-dense industry into a capital-dense industry.Automated methods of manpower deployment and timekeeping and the monitoring of all equipment back to a central control point are discussed as ail-important means of obtaining maximum utilization of high-cost capital investment.Principles of payment of the work-force, and the utilization of equipment 24 hours a day, seven days a week and the maximum number of days a year, are dealt with as means of achieving maximum capital utilization. Some of the new technical underground and coal preparation problems which will undoubtedly result from the concentration of workings and maximum machine utilization are discussed, and the author makes suggestions as to how these might be solved.In short, the author predicts that if the coal mining industry is prepared to recognize the problems and invest in modern equipment backed by highly trained staff. then the outcome will justify the high capital investment involved. He stresses the importance of human communications in achieving this end."

Jan 1, 1970

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By A N. Danoucaras, S E. Goater, D Hearne, A M. Bansuan

It is globally recognised that existing and emerging mining activities should be conducted in a æsustainableÆ manner for the entire life of mine. Many companies annually publish corporate sustainability reports to demonstrate their actions in accordance with international expectations. This concept of sustainable mining practices also applies to mine water management, with influences often extending beyond site operations, affecting surrounding catchments and community users. This paper explores differences in conceptual and operational terms of æsustainableÆ mine water management within the Philippines. Outcomes of a review of corporate sustainability reports, governance documentation, research programs, and stakeholder knowledge acquired through action-research workshops are presented. The paper aims to inform and support future capacity building exercises delivered by the International Mining for Development Centre (IM4DC), with outcomes tailored to government officials and policy makers of developing countries. The project is funded by IM4DC, which is working with AusAID to identify needs and develop capacity with regard to mining for development; specifically, issues pertaining to governance and regulation, social and environmental sustainability, and operational effectiveness in developing countries.CITATION:Bansuan, A M, Goater, S E, Danoucaras, A N and Hearne, D, 2012. Integrated sustainable water management in mining for development in the Philippines, in Proceedings International Mine Management 2012, pp 205-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young's modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By Pasi Korkeakoski

There are about 400 multi-storey buildings founded on wooden piles in the city centre of Turku in Finland. Soil conditions are variable from hard rock to very soft clay. Due to the soil conditions and ground water lowering there are basically four different types of underpinning projects. Under dimensioned cohesion piles in a deep clay layer, decaying cohesion piles, a combination of these two reasons and decaying end bearing piles in a thin clay layer area. Many different execution methods have been used such as impact driving, jacking and drilling and combinations of these.

Jan 1, 2000

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

By Zhao-cheng Liu

Iron oxide red pigment powders of high quality were synthesized from pyrite cinders. Iron ox-ide red pigment powders were synthesized by hydrothermal method from the precursor of Fe(OH)3 and Fe(OH)2 colloid, which were obtained after ammonia solution reacted with acidic leaching solution produced by the reaction of pyrite cinders with sulfuric acid. Effects of reaction concentration, reaction temperature, reaction time, pH value and n(Fe2+)/n(Fe3+) on main properties of oxide iron red were studied by experiments. The prepared particles were characterized by means of X-ray diffraction (XRD) and scanning electron microscope(SEM). The results revealed that the synthesized iron oxide red particles were _-Fe2O3 and pseudocubic with particle size of 0.50~0.75µm. Furthermore, the quality of iron oxide red pigment powders reached the first grade of national standard (GB1863-89 ).

Jan 1, 2009

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate process plants requiring high throughputs presents unique metallurgical environmental and sustainability challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life-of-mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy and high ore variability, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, high capital and operating costs, worldwide constraints on resource availability, complicated regulations in emerging economies, changing demographics of mining operations with ever-changing cultural or community issues and the urgent need for a better assessment of project viability to reflect the dynamics of present mining scenario. Developing breakthrough solutions to these problems is the key to success of any new project and maintaining profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial along with the need for a more lateral thinking, strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex metallurgical problems.IntroductionThere is a plethora of challenges in developing new ore bodies. The metallurgical complexity of these deposits has increased significantly due to the need for mining lower grade ores along with the presence of deleterious elements that have environmental and processing implications. In addition, many of the mining projects are capital intensive due to high throughput requirements to be economical along with the need for building infrastructure due to remote locations, while operating costs steadily increase due to high reagent, energy and labour costs, increased state royalties and community obligations, to name a few of the key factors. There is also scarcity of water in many regions requiring the use of sea water or brackish water, which has both environmental and metallurgical implications. The shortage of qualified technical manpower adds significantly to the woes of many mining companies. Considering these multiplicity of challenges, it has become imperative for many mining companies to be innovative in addressing these issues."

Jan 1, 2015

By G. E. Perry, R. D. Seba

The steam soak process is the most widely applied and most successful thermal supplemental recovery process in use today. This process, which consists of injection of steam in various quantities into a well that is subsequently used as a producer, can be repeatedly applied to the same well. The treatment, if successful, will increase the production rate of the well for a given period. For this reason, the steam soak process should be considered primarily as an acceleration method rather than as a method for producing oil that could not be recovered by primary means. However, application of this process to reservoirs containing viscous crude may produce oil that otherwise would have zero present value or would be produced at such low rates by primary methods that it would not be profitable. A major necessity for the successful application of the steam soak process is a source of natural energy. This source of energy may exist in one or more of the following forms: expansion of fluids, compaction, gravity drainage. This study was undertaken to determine the effect of gravity drainage on steam soak production and recovery and to develop a method for predicting production rates, ultimate recovery, and heat requirements when applying this process to a reservoir in which the primary driving mechanism is gravity drainage. (For additional discussion of some of the factors that affect recovery of viscous oils by the steam soak process, see Ref. 5.) Model The model developed for analyzing the performance of the steam soak process in gravity drainage reservoirs is a modified form of that developed by Matthews and Lefkovits.1,2 The model used in this study consists of two concentric cylindrical volumes of productive formation with cap and base rock of impermeable material. The inner cylinder, extending from the radius of the wellbore to some predetermined radius, is referred to as the hot zone; and the outer cylinder extending from the exterior boundary of the hot zone to the outer drainage boundary will be referred to as the partially heated zone. Fig. 1 is a schematic cross-section of the model, indicating its thermal properties. Horizontally the reservoir is divided into two regions, the upper region having a high gas saturation and residual liquid saturation, and the lower region containing a high liquid saturation. The boundary between these two regions is referred to as the free surface, which drops and changes shape as fluid is produced from the reservoir. The model was used to analyze the steam soak process by applying the following assumptions: 1. The horizontal formation is composed of one or more homogeneous noninterconnected layers containing incompressible fluids. Each layer is treated separately. 2. The hot zone is heated by the initial soak and is maintained at the steam temperature corresponding to atmospheric pressure by resoaking. 3. The height of the free surface at the producing well is at all times zero (producing well is pumped off). 4. The position of the free surface at the start of

Jan 1, 1970

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986