Search Documents

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By David Kress

Mill crushing drive systems are essential to cement producers. With the increased emphasis on operating efficiency, it is vital that these systems be dependable and reliable. No one needs the costs or headaches associated with unscheduled downtime or inefficient machinery operation. A reliable drive system starts with the proper selection of the ring, or girth, gear and continues through proper maintenance. Ideally, selecting the right girth gear brings together the gear manufacturer, the system designer and the end user. The gear manufacturer must know the details of the application, the demands that will be placed on the gear and the nature of the equipment to be driven. Similarly, the user and the system designer must be familiar with the variables that affect gear drive performance and service. For example, an application that places a torque load on the drive in excess of its rated capacity will result in gear tooth distress and, in severe cases, breakage.

Jan 1, 2000

By Edmonds W, Jeffcoat R

The completion of the first two open hearth furnaces in the new No. 2 open hearth plant at Port Kembla will increase Australian production of steel by 350,000 tons of ingots per annum.The paper gives an outline of the essential features of open hearth design and auxiliary equipment required to operate the two modern open hearth furnaces at present being installed.INTRODUCTIONThe increasing demand for steel required by Australian secondary industries led to the decision to construct and operate No. 2 open hearth plant at Port Kembla. Two basic open hearth furnaces of the most modern design are under construction and it is anticipated that these units will be commissi.oned in September 1956. Australian steel capacity will thereby be increased by approximately 350,000 tons of ingots per annum.PLANT LAY-OUT AND CONSTRUCTIONIn the design and lay-out of this plant the emphasis has been on efficient material handling with simplicity of design and operation. Overseas methods were studied and these studies, together with experience gained at Newcastle and Port Kembla open hearth shops, enabled this plant to be built to a standard which compares favourably with any other in the industry.Initially two furnaces, each of 2,75 tons capacity, have been built, but provision has been made in. the design and lay-out to enable expansion to six furnaces.The location of the new plant in relation to the existing units will be noted in Fig. 5. It is one of the first units to be built in an area which will dovetail into a pattern for...

Jan 1, 1957

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By A. Iannacchione

Major Hazard Risk Assessment (MHRA)1 is used to help prevent major hazards, e.g., fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, etc., from injuring miners. The structured process associated with MHRA helps to characterize the major hazards and evaluate engineering, management and work process factors that impact how a mine mitigates its highest risk. The National Institute for Occupational Safety and Health (NIOSH) studied the application of this technique to US mining conditions through a field-oriented pilot project. Risk assessment teams used in the pilot project were primarily composed of mining company personnel. Ten case studies were performed over a wide cross-section of mines. These mines were representative of the important mining commodities in the US minerals industry, i.e. coal, metal, non-metal, and aggregate. Also, the sizes of the mines ranged from small to large and were located across the country. The ten case studies demonstrate that most US mines have the capability to successfully implement an MHRA and that the MHRA methodology produced additional prevention controls and recovery measures to lessen the risk associated with a select population of major mining hazards. The basic ingredient for a successful MHRA is the desire to become more proactive in dealing with the risks associated with events that can cause multiple fatalities. A successful outcome is marked by a thorough examination of existing prevention controls and recovery measures. When pressed to consider more controls to further mitigate the risk, a well-staffed risk assessment team was able to identify additional controls. For these mining operations, it was important to add additional controls, even if they were not required by existing mining regulations, to lower the risks associated with the major hazards under consideration. If a mining operation is not willing to commit its best people to an MHRA or will not provide them with sufficient time to see the process through to its conclusion, the MHRA output may prove to be useless. Additionally, if a mining operation is not prepared to discuss its major hazards in an open and honest fashion and to present the findings of the risk assessment in a written report, the MHRA output will be unclear, and attempts to monitor or audit important controls may not be possible. A MHRA is most effective when the mining operation possesses 1) a proper understanding of its hazards, 2) experience with informal and basic-formal risk assessment techniques, 3) proper facilities, machinery and equipment, 4) suitable systems and procedures that represent industry Best Practice, 5) appropriate organizational support with adequate staff, communications and training, 6) a formal and thorough plan for emergency response, and 7) a safety risk management approach that is promoted and supported at all levels of the organization.

Jan 1, 2008

By W. Scheetz

The Brewer Gold Mine is an open-pit, heap leach operation that processes about 122 kt/m (135,000 stpm). The mine is operated by Brewer Gold Inc., a subsidiary of Westmont Mining Inc., and is located near Jefferson, SC, about 80 km (50 miles) southeast of Charlotte, NC and 80 km (50 miles) northeast of Columbia, SC (Fig. 1). All of the ore to date has been produced from a breccia body of hydrothermal origin and a related smaller body of fault-controlled ore, known as the B-6. Reserves at the time the mine commenced production were 4.6 Mt (5.1 million st) grading 1.4 g/t (0.042 oz per st) gold. History Although some reports of a pre-Revolution War shaft at the Brewer are in the literature (Lieber, 1856, Nitze and Wilkens, 1897), gold was first produced in earnest from the Brewer Mine in 1828. Production occurred primarily from placer deposits south of the present mine workings. Lieber noted in 1856 that “every branch, gulch, ravine or even declivity of the main hill has been washed and rewashed.”

Jan 1, 1991

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By Michael Kukay, Paul Conrad, Cosmas Opoku-Ware

This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 ft below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana.

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By Paramguru R. K, Jena P. K

Increasing demand for copper, lead and zinc with continuous depletion of good grade ore reserves, warrants the need for utilization of lean and complex ores of these metals. There is worldwide effort to develop suitable processes for these purposes. The present paper deals with the chloride leaching of complex base metal sulphide concentrates of two Indian deposits. A two stage leaching process is suggested keeping selectivity of metal dissolution in view.In the first stage most of the lead and zinc are reacted with dilute FeCI3 (0.3M) solutions at a temperature ono°c where major portion of the lead remains in the residue and zinc reports in solution. After taking out lead chloride by brine leaching, the residue has been treated for copper dissolution. A concentrated FeCI3 leaching at boiling temperature as well as ambient aqueous chlorine leaching have been separately tried to dissolve out the copper from the residue. Based on the results obtained, a flowsheet for the proposed process is presented.

Jan 1, 1981

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,' the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson's number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By Inn-Joon Park

Major problems associated predicting soil-structure interaction behavior are based on the fact that soil is neither homogeneous nor elastic and soil properties are spatially variable. There also exist significant coupling problems between the behavior of the structure and geologic media. When designing foundation or other geotechnical structures, the load transfer between the soil and structure takes place at the contact surface. This surface is called the interface. The behaviors of interface play an important role in the load-deformation response of soil-structure interaction systems. The purpose of this study is to develop improved model for simulation of saturated sand-steel pile interface behavior based on a general concept, called the disturbed state concept (DSC), which can characterize the behavior of saturated soils under dynamic loads. In this study, the Disturbed State Concept (DSC) constitutive model is calibrated and modified for steel pile-saturated sand interface and interaction by using the continuous hardening model for relative intact (Rl) state and the critical state model for the fully adjusted (FA) part in the saturated sand material. The general formulation for implementation has been developed. Then, the DSC model with modification for interface and saturated sand is implemented in finite element program based on the generalized Biot's theory. The interface tests under one-way monotonic and two-way cyclic loading and cyclic triaxial tests are executed for defining the parameters for interface and surrounding soils. Based on these parameters, steel pile-saturated sand interface and interaction are numerically simulated using the finite element program modified in this study. The DSC predictions show improved agreement with the observed results from laboratory test.

Jan 1, 2002

By Xuan Li

Aluminum slag is generated when aluminum metals are recycled through a smelting process in the presence of salt. There are small amounts of aluminum metals trapped in the aluminum slag. This research aims at evaluating the use of aluminum slag as an expansion agent for the production of lightweight concrete by taking advantage of the residual aluminum metals in the slag. The research identified key elements of producing lightweight concrete products through utilizing various mixture components including sodium hydroxide (NaOH), lime (CaO), cement, and gypsum. The volumetric expansion rate was investigated and the density and strength of the products were determined. The results show that aluminum slag can be utilized for the production of lightweight concrete products.

Jan 1, 2010

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By Paul Fouche

The past decade has seen a tremendous revival of the base metal industry in Africa, coupled with an unprecedented increase in the prices of base metal commodities in the last couple of years. The theme of the 4th Southern African Base Metal Conference, is therefore, ?Africa?s base metals resurgence?. This conference will explore the contributions made by the mining and metallurgical disciplines to the base metals industry in Africa. It will also investigate how the base metals industry in Africa can capture the maximum potential from the increase in base metal prices through research, innovative thinking, new ways of operating and project implementation. The conference will also consider the influence of Europe?s REACH programme on the base metal industry in Southern Africa. The conference will include a technical visit to Rössing Mine (Uranium) and will be followed by technical visits to Ongopolo (copper), Skorpion Mine (zinc) and Rosh Pinah Zinc Corporation(zinc and lead). The conference, to be held in Swakopmund, Namibia, also confirms the commitment of the Southern African Institute of Mining and Metallurgy (SAIMM), to hosting a regular forum on base metals in the Southern African region. Swakopmund is an ideal conference venue for local and international mining and metallurgical professionals to be exposed to the latest advances in exploration, resource evaluation, projects and technological advances in Southern Africa?s base metal industry. The organising committee is looking forward to your participation at the conference in July 2007.

Jan 1, 2007

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By Kelly E. G

NZ Steel's flushing slag typically contains 1.2 per cent V203. Extraction of vanadium from powdered slag using a salt (NaCI or Na2CO3) roast/leach process was investigated. With NaCl, optimum extraction conditions were a charge containing 10 per cent NaCI, roasting in air at 875°C for 4 hours, followed by leaching in dilute H2SO4. Extractions were typically 30-50 per cent. NaCI roasting did not chemically attack the slag; the phase transformations that occurred were due to high temperature oxidation. Slag particle size had a significant effect on extraction.Optimum conditions for extracting vanadium by Na2C03 roasting were 20 per cent Na2CO3 in the charge and roasting in air for 3-4 hours at 850-875°C followed by water leaching.Na2CO3 roasting involved chemical attack that resulted in the formation of perovskite (CaTiO3) and carnegieite (NaAISiO4).The extent of vanadium extraction depended on the amount of Na2CO3 added and the original slag SiO2 content.Compared to the separate roasting treatments, simultaneous treatment with NaCI and Na2CO3 gave lower vanadium extraction, while requiring considerably higher roasting times and temperatures.

Jan 1, 1982

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013