Search Documents

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Shanti Arangala

Several improvements were made to the single strand rod mill at Laverton to increase production, reduce maintenance and improve several aspects of product quality. With changes to the water cooling line and control system, cobbles could be significantly reduced, more consistent properties obtained and yield improved. An upgrade of the laying head enabled vibrations to be reduced and thus allowed for higher speeds on small sizes. With potential for dramatically increased pipe life, a new pipe support and laying pipe system provided for improved laying pattern on small sizes and thus more uniform cooling on the conveyor and better coil package. This paper discusses details of these equipment and control system upgrades and the resulting benefits that have been realized from the project.

Aug 16, 2017

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function y(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [ ] where N is the total number of samples, Xi is the sample value at the i - th location, Xi+h is the sample value at the i + h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2, up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any arbitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of one-dimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity.

Jan 11, 1985

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By R. G. Burdick

The problems presented by old mine workings affect both present day mining and land development. An automated method of locating these old mines from the surface using electrical resistivity techniques was de-veloped earlier under a Bureau of Mines contract. Subsequent Bureau research has refined the techniques and expanded the area of study to a variety of geologic provinces. During this research, six mining areas in the United States were in-vestigated with the Bureau's automated resistivity method. This report describes the mining areas involved and the results of the resistivity investigations, which showed a high rate of success in detecting old mines. It also describes the field measurement techniques and data analysis procedures.

Jan 1, 1986

By Michael V. Markel

This report summarizes work performed under USBM Contract No. J0100047 revealing the performance characteristics of a composite-type resilient screen deck. The ability of the composite to perform or compete with steel in noise attenuation and longevity was of interest. Tests were conducted at the River King Preparation Plant of Peabody Coal Company. This facility was chosen because it provided parallel process flow and met standard coal cleaning requirements. Comparisons could be made between the adjacent resilient and steel screen decks under similar operating conditions. Noise reductions of 1-6 dBA were realized in the near field. Although the test period did not determine resilient screen life, indications are favorable for their longevity.

Jan 1, 1981

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By T. H. Janes

THE POSSIBILITY of producing pig iron from iron ores of British Columbia for a west coast primary iron and steel industry has been investigated by the provincial government and by commercial interests on sever.al -occasions. The latest study is that currently under way by The Consolidated Mining and Smelting Company of Canada, Limited. The Company is studying the possibility of making pig iron from the oxide calcine resulting from the roasting of pyrrhotite. tailings used in making sulphuric acid for fertilizer production at Kimberley. A comprehensive report on the subject .of establishing a primary iron and steel works in the Province, based on local iron ores, was prepared by Arthur G. Mc-Kee and Company of Cleveland, Ohio, in 1942 for the B.C. Minister of Mines and is available to interested parties. A detailed survey on the subject was also pre-pared in 1954 by Dr. G. P. Con-tractor, then .of the British Columbia Research Council. Considerable information is there-fore available on most aspects of an integrated primary iron and steel industry in British Columbia to supply the needs of the western provinces. To date, however, no basic iron industry has been established despite the .occurrence of high-grade iron ore deposits on the offshore islands and the high freight charges on iron and steel products brought into the area from Eastern Canada and overseas producers. The chief deterrent has always been the relatively small and highly diversified market available to a local steel producer. Other major fact-ors have been the lack of sufficient proven reserves of iron ore, and the difficulty of making pig iron, suit-able for steel manufacture, economically on a small scale. Technical and economic conditions have changed considerably since World War II and the establishment of a primary industry based on electric furnace production of pig iron or on one of the direct reduction processes, coupled with electric furnace steel production, may now be economically feasible.

Jan 1, 1958

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By Bruce McDonald

This report contains the Phase I findings of a study to select and test devices for preventing lack of alertness in haulage truck drivers. The extent of the problem was determined by visiting surface metal and nonmetal mines, interviewing drivers and safety personnel and reviewing accident reports. A number of devices for detecting a lack of alertness were considered and three were recommended for testing in actual operation.

Jan 1, 1977

YOUR Excellency, Fellow Members of the Australasian Institute of Mining Engineers and Gentlemen:-Nearly a decade has passed since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 with usagreat change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everythingin my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1912

This consolidated index covers all publications of the Institute for the years 1926 through 1935. The following list indicates subjects of volumes and gives numbers or abbreviations used to designate them. TRANSACTIONS VOLUME *G26. Petroleum Development and Technology in 1925 (Published in 1926). *G26. Petroleum Development and Technology in 1926. *E27. Institute of Metals Proceedings. 73. Nonferrous Metallurgy, Milling and Concentration, Nonmetallic Minerals, Institute of Metals and Iron and Steel. [ ]

Jan 1, 1936

By D. M. Muir

Thiosulfate offers a non-toxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32-. It is shown that an understanding of the copper speciation and sulfur speciation is required to optimise this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2001

Leading Article from "British Medical Journal," London, 4th, November, 1944.Assuming that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid, Denny, Robson, and Irwin thought that if the solubility of siliceous material retained in the lungs could be suffciently reduced the usual fibrotic response could be diminished or prevented. They discovered that aluminum powder rendered siliceous material insoluble in vitro by coating the silica particle with a thin film of gelatinous hydrated alumina, which on drying formed crystalline alpha aluminum monohydrate. The presence of this adsorbed layer on the surface of the quartz was shown by staining it with aurin. That metallic aluminum dust produced no fibrosis in the lungs was demonstrated by dust-inhalation experiments on eight rabbits. Attempts were therefore made to prevent silicosis by mixing quartz with metallic aluminum dust.Animals exposed to quartz dust developed typical silicosis in about five months, but the addition of 1 per cent. aluminum powder prevented this even after exposure had been lengthened up to 22 months, provided the aluminum powder was of a particle size below 5. This year Crombie, Blaisdell and MacPherson have reported the treatment of 34 silicotic miners by the daily inhalation of fine aluminum powder freshly ground from small aluminum pellets in a specially constructed mill. Daily treatment began with five-minute inhalations, which were gradually increased to 30 minutes. Some of the men received 300 treatments, but the majority only 200. Out of the 34 cases thus treated clinical improvement was manifested by lessening or disappearance of shortness of breath, of cough, of pain in the chest, and of fatigue. In 15 cases the condition became stationary and remained so in spite of continuous employment in silica dust throughout the treatment. The progress of the disease was assessed by means of tests for respiratory function repeated at three-monthly intervals. Obviously this treatment cannot be regarded as a cure for silicosis, since it cannot restore lung tissue which has undergone fibrotic change; but Crombie and his colleagues believe that the inhalation of finely particulate aluminum powder offers every prospect of preventing the development of human silicosis.In view of these findings, it is surprising that repeated papers by Goralewski from Germany describe various types of lung disease attributed to aluminum dust, and press for them to be scheduled under the Workmen's Compensation Act in that country. Seven hundred workers were investigated. They were making, probably by a stamping process, aluminium powder containing about four milliards of particles of dust per grain, and are reported as complaining of dry cough with pain on breathing, shortness of breath, poor appetite, and gnawing abdominal pain. Spontaneous pneumothorax developed in four workers. No abnormal physical...

Jan 1, 1945

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968