Search Documents

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By E. V. Redin, B. A. Dubrovsky, E. V. Knyazev, A. I. Starikov

"Ti-V magnetite is one of the most abundant composite ore resources in the world. This ore cannot be fully processed via blast furnace technology because of high content of Ti02. According to the investigations carried out in the USA and Japan ITmk3 RHF (Rotary Hearth Furnace) technology is a breakthrough in Ironmaking. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from Ti-V magnetite ore via the ITmk3 by means of the lab scale testing. Samples of ore from the Maly Kuybas deposit (Southern Ural), carbon reductant and fluxes were chemically analyzed. Green pellets were processed via a lab chamber furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities [l]. After pilot testing at Kobe Steel's Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics put into operation the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota) in 2010. Results were consistent with nugget characteristics confirming ITmk3' s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from the Ti-V magnetite bearing ore with high content of Ti02 and Alz03 has been done. It is well known, if a lot of Ti02 and Alz03 enter the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace. Besides, high content of Alz03 raises the melting temperature of gangue minerals disturbing the coalescence of reduced iron to the nuggets."

Jan 1, 2013

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -o.nv vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Sergio N. Monteiro

Polymer matrix composites have been applied in components such as helmets and shielding for which toughness is a major requirement. Natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. The objective of this work was then to assess the Izod impact resistance of polymeric composites reinforced with different amounts, up to 30% in volume, of a promising high strength natural fiber from the Amazon region known as curaua. The results showed a remarkable increase in the notch toughness with the amount of incorporated curaua fibers. This can be attributed to a preferential debonding of the fiber/matrix interface, which contributes to an elevated absorbed energy.

Jan 1, 2009

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By Mohamed Y. Bakr, Aly M. Abdel-Rehim

The present work is related with mechanical activation of processing of Egyptian wolframite by simultaneous ball-milling and pressure alkaline leaching, to improve the recovery of tungsten from wolframite. The results show a total recovery of tungsten from wolframite (97.8- 98.7%) by simultaneous ball–milling and alkaline leaching at temperature 175-200oC. It is concluded that processing of wolframite by simultaneous ball- milling and leaching is mechanically activated and accelerated as a result of the grinding action of steel balls that caused the immediate rupture by continuous removing the product layer of the reaction ( sodium tungstate and iron and manganese hydroxides ) from reacting particle surfaces. This leads to the exposing of fresh and activated wolframite particle surfaces to alkaline leach solution and consequently the acceleration of the reaction of wolframite leaching .The results of the kinetic study 0f alkaline processing of wolframite and its mechanical activation show that the system is under kinetic control.

Jan 1, 2015

By Kotaro Ogura

"Ethylene has been produced in aqueous solution from CO2 by the electrochemical reduction driven by a natural energy. This process is useful for storing a large amount of the natural energy. In the closed system, the conversion efficiency of CO2 is almost 100%, and the maximum selectivity for the formation of ethylene is more than 70%. On the other hand, the current efficiency for the competitive reduction of water is less than 10%. The electrolysis is practicable under such special conditions as three-phase interface consisting of gas, solution and metal, concentrated solution of potassium halide, low pH and copper or copper halide-confined metal electrode. These requirements are thoroughly examined, and the grounds to reply upon are revealed. A series of chemical apparatuses including an electrolytic cell in a large scale are designed for the ethylene production, which allow us continuously to supply raw CO2 and to extract the product.IntroductionIn connection with the depletion of the petroleum reserve, much attention has been paid to the utilization of natural energies such as sunlight, wind force and waves. However, these energies are always changeable, and some means of storing them are necessary for the common use. In general, natural energies are transformed to the electric energy at the time of utilization, but the electricity is not very storable. This is one of the reasons why the application of natural energy is not so expanded. On the other hand, the storing of natural energy by plants is very skilful. In the photosynthesis, solar energy is transformed to chemical energy by fixing carbon dioxide."

Jan 1, 2009

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectic Sn-Pb) and two types of nickel- based UBMs, electroless Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed. The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples of Sn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectie Sn-Pb) and two types of nickel- based UBMs, electro less Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case 'of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed, The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples ofSn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By Yotamu Stephen Rainford Hara

"The aim of our work is to investigate a low energy and clean route for the recovery of copper and cobalt from complex sulphide mineral concentrates. The mineral concentrates were roasted in air, in the presence of CaO (MS + CaO + 202 =MO+ CaS04) at temperatures below 973K. The roasted products containing CuO, CoO and Fe203 were carbothermically reduced at 1073K within an hour to preferentially reduce copper and cobalt. The kinetics of reactions were studied using the thermogravimetric technique and by characterisation ofreaction products using the XRDSEM-EDX techniques. The effects of MS:CaO ratio, roasting temperatures and physical nature of the mineral concentrates were analysed. The method for capturing S02 by forming CaS04 was analysed for reuse in the process. The energy balance for the above process is compared with that of conventional continuous smelting/converting process.1.0 IntroductionCopper sulphide mineral concentrates from Zambia contains substantial amouot of cobalt. The cobalt metal content in the concentrates ranges between 0.7 and 2 % weight, which corresponds to 3 and 9 % weight copper, based on the spot price of copper ($7 386/tone) and cobalt ($31 000/tone). Although the traditional approach using a combination of roasting-leaching-electrowining steps can be applied to recover copper and cobalt from sulphide mineral concentrates [1-4], there are two major draw backs of the traditional process: (i) the S02 emitted during roasting is too lean for economical conversion for sulphuric acid manufacture, which causes serious environmental pollution. (ii) silver and gold which are normally present in the sulphide concentrates are lost out [5] because they are not leachable by H2S04 or HCl which are the common leachants. The above two problems have been overcome by adopting flash smelting in which a rich S02 gas above 20% is produced [1, 5] and successfully converted into sulphuric acid. The precious metals tend to partition to blister copper and recovered during refming. However, nearly all cobalt is lost into the slag phase uoder oxidising condition which prevails during flash smelting. It is important to note that the cobalt content in the slag can be up to 2.6 % weight [6]. The recovery of cobalt from the slag is a process which requires huge amouot of energy since the slag is smelted above 1873K [6]. With a view of minimising the amouot of energy and S02 emission during metal recovery, our investigation involves roasting the sulphide concentrates in the presence of lime and reducing the roasted samples with carbon."

Jan 1, 2013

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

By L. A. André Santos

Atmospheric processing of nickel lateritic ores with low costs has been encouraged. In this work the kinetic of atmospheric acid leaching of a northern- Brazilian ore with 1.63% Ni and large amount of fine particles (d50 ≈ 0.075 mm and 40% below 0.038 mm) is presented. Chemical analysis showed a trend of Ni and Fe concentration in finer fraction (−0.075 mm) and Si and Mg in the coarsest one (−0.500 + 0.150 mm) associated to distinct mineral phases. Nickel is widespread in the mineral matrix. Distinct behaviors were observed as a function of particle size associated to the distribution of silicates and iron oxides in the ore. The kinetic modeling indicated that leaching is controlled by porous layer diffusion at 65 °C, but at 95 °C exhibits a mixed control by porous layer diffusion in initial minutes (60 min) and by chemical reaction or diffusion through the pore layer in final minutes (60–240 min) depends on metal evaluated.

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Nomenclature: A: area (m2), C: heat capacity (WIK), cp: specific heat (J/Kg K), d: internal tube diameter (in), F: correction factor for multi-pass and crossflow heat exchanger, h: convective heat transfer coefficient (W/m2K), k: thermal conductivity (W/mK), L: length (m), m: mass flow rate (Kg/s), W: flow rate, N: number, Q: heat rate (W), R: thermal resistance, T: temperature (°C), U: overall heat transfer coefficient (W/m2K), ;1,,P: pressure drop (Pa), ;1,,T: temperature difference (°C), p: density (lb/ft3), N: number of tube passes, U,: velocity in tubes, iJh: head loss in feet of flowing fluid, Up: velocity in the pipe leading to and from the heat exchanger (ft/sec), µ: viscosity ( cp ), Llpf frictional pressure loss (psi/l 00 equivalent ft of pipe) Subscripts: b: baffle, c: cold, cf counter flow, ex: exchanger, f: fouling, h: hot, i: inlet-inner, ib: inlet baffle, lm: logarithmic mean, m: mean, o: outlet-outer, s: shell, t: tube, w: wall AbstractThe main bottleneck for primary aluminum production industry is dealing with a huge amount of input energy. The fact is that part of provided energy to aluminum production smelters will be lost as waste heat and it never used for aluminum production. One part of waste heat is escaping from the potroom exhaust gases, which was studied for possible recovery in a desalination plant to produce distilled water and the paper was presented in 2011 TMS Annual Meeting. However, it was shown that waste heat recovery plant to produce distilled water is highly profitable but the main fact is that the exhaust gases from potroom are highly corrosive, abrasive and dusty. The main challenge for desalination plant construction, which is using aluminum smelter exhaust gases as the main heat source, is the highly corrosive environment that makes the situation difficult and complicated for equipments design and plant construction. In this paper, we are trying to study a detailed investigation regarding the heat exchangers fouling, corrosion in heat exchangers including heat exchangers' material, how often we need to shut down the plant for maintenance or cleaning, and plant thermal efficiency with considering fouling."

Jan 1, 2012

By Shadia J. Ikhmayies

"Tin oxide (SnU2) thin films of thicknesses in the range 100-600 nm were prepared on glass substrates by vacuum evaporation at ambient temperature. The films were characterized by transmittance measurements, X-ray diffraction (XRD), scanning electron microscope (SEM) observations and energy dispersion X-ray analysis (EDAX). It is found that the films have high transmittance and non sharp absorption edges. XRD diffractograms showed that the films are amorphous and the SEM micrographs showed that the surfaces are smooth, uniform and well covered with the material. The EDAX analysis showed that the films are deficient in oxygen. Indirect optical bandgap energy and Urbach tailing in the bandgap was observed, and the width of the tail, which is related with disorder and localized states, was estimated.IntroductionTin oxide is an n-type wide bandgap semiconducting material with a direct bandgap energy of 4 eV and an indirect bandgap of 2.6 eV [1], where inherent oxygen vacancies act as an n-type dopant [2], Tin oxide thin films have been used for transparent electrodes in photoelectric conversion devices namely amorphous silicon solar cells, liquid crystal displays, gas discharge displays, etc. [3]. Perfectly amorphous thin SnO2 films show good electrical response to reducing gases in air and could, hence, be applied to construct semiconductor gas sensors where the metal oxide films function as a monograin-eqivalent active layer [4]. Amorphous SnU2 can also be used in extended gate field-effect transistors (EGFET) as a pH sensor, where the sensitive part is made of the SnO2/Al structure. This device can be used to detect and to quantify any kind of substance that can produce or consume protons, like an enzymatic reaction, therefore showing a large range of applications as biosensors [5].There are different methods to prepare SnO2 films, such as atomic layer deposition (ALD) [6], reactive magnetron sputtering [7], chemical vapor deposition [8, 9], dip coating [10], spray pyrolysis (SP) [3, 11-14], and evaporation [8], The thermal evaporation method was chosen to produce SnO2 thin films in this work because deposition by this technique does not present any compositional problems. In addition, it is a low temperature technique, which increases the probability of producing amorphous films. To increase this probability, the films were deposited at ambient temperature."

Jan 1, 2012