Search Documents

By Jean-François Domgin

This paper aims at presenting numerical results showing the impact of different parameters on the limitation of entrained slag from ladle to tundish during the ladle drainage. These parameters are process parameters, slag properties or external actuator acting directly on ladle slag behaviour. Numerical simulations based on the use of the CFD Fluent software illustrate the vortexing and non-vortexing phenomena appearing during the ladle drainage. This numerical tool validated by experimental data acquired on water model has been applied to industrial configurations. It shows that the slag properties (viscosity, surface tension?) or some modifications of parameters (slide gate opening, geometry of the ladle bottom?) have a positive effect on the slag entrainment and also on the decrease of the ladle heel. Finally, the modelling of the behaviour of an external actuator injecting some gas in the region of the nozzle reveals interesting possibility for reducing slag entrainment from ladle to tundish during the final steps of the drainage.

Jan 1, 2006

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

By Sundarrajm Suresh, Hrushikesh G. Pimpalgaonkar, Thiyagarajan Paramadayalan

In this paper, a model of a fuel cell system has been proposed to account for the membrane physics at the micro level which is coupled with the macroscopic flow and mass transport phenomena occurring in a single channel of a Polymer Electrode Membrane Fuel Cell (PEMFC) system. We have developed a novel approach to model the catalyst layer electrochemical processes in a Membrane Electrode Assembly (MEA) and coupled it with mass transport and fluid flow calculations at the channel level using STAR-CD commercial software. The predicted values of the cell voltage from this micro-macro model are validated with experimental data available in the literature. A sensitivity analysis has been carried out to study the effect of the design and operating parameters such as catalyst loading and initial temperature on the overall performance of the PEMFC. The results indicate that the cell voltage increases at higher platinum catalyst loading and is also independent of the choice of initial cell temperature.

Jan 1, 2012

By K. Th. Mavrommatis

Cleanness of steel is justified, measured and estimated in steelmaking process through different concepts which are mainly based on operational, empirical or semiempirical parameters and describe ?cleanness as a state?. In this work a theoretical concept is developed, considering ?cleanness as a process? and introducing a dynamic aspect into the quantification of cleanness of a steel melt, linking operational parameters with physicochemical variables, which are based on first principles. This concept and the here derived and developed variables and parameters are based on the earlier defined agglomeration index (AI) of a steel melt, the ratio of the mean inclusions diameter (MID) to the mean inter-particle distance (MIPD), which is shown to be a measure of the agglomeration tendency of the melt after deoxidation, and can serve both, to monitoring cleanness during steelmaking operation and to be useful as a basis for mathematical modelling of cleanness and of the metallurgical measures in plant, associated with production of clean steels.

Jan 1, 2006

By Ximena Massone

Chile is the most important copper producer in the world and the mining sector plays a key value in its economy. However, at present the country does not have a satisfactory set of regulations about closure and restoration of mining operations. In our country many mining operations will, in the near future, shut down their activities, therefore, it is of utmost importance to elaborate and enforce a set of regulations to prevent risks and to protect the environment. The present study is focused on reviewing and analyzing the existing national regulations about the closure of mining operations and preparing a comparative analysis with other international regulations of countries with mining experience. The final results of the study will be a legal proposal to regulate the closure of mining operations in Chile, aiming at minimizing the potential environmental adverse impact, internalizing the social costs by the relevant operators and defining all aspects of liability for the environmental damage.

Jan 1, 1999

By Toshihide Takenaka

Improvement of corrosion resistance of Mg metal by addition of rare earth metal (RE) was studied, and the effect of surface oxide layer with RE was investigated. The corrosion resistance of Mg was remarkably improved by adding a small amount of RE, and the suitable RE content was clarified. The corrosion resistance of Mg was particularly bettered by conversion coating using a solution including both RE(NO3)3 and Mg(NO3)2. This result indicates that the surface oxide layer consisting of both Mg and RE gives good corrosion resistance to Mg metal. In this study, direct electrodeposition of Mg metal containing RE was also tried in molten chloride with RE chloride, and it was shown that electrolysis could be performed stably. The RE content in the deposited Mg metal was depended on the concentration of RE chloride in the bath and the cathode potential, and Mg metal containing the suitable RE content for its corrosion protection was obtained easily by direct electrolysis.

Jan 1, 2006

By Claire A. Chanenchuk

Catalytic Extraction Processing (CEP), a technology commercialized by Molten Metal Technology, Inc., a US.-based company, can convert industrial, household, and government wastes into commercial resources. CEP is an innovative elemental recycling technology that uses a molten metal bath to completely dissociate hazardous or toxic components of a feed and convert them to valuable products. The catalytic action of the molten metal bath converts the feed to its elemental constituents and the reducing atmosphere prevents the formation of any dangerous byproducts (NOx, SOx, dioxins, furans, etc.). Selective reactant addition allows engineering of valuable products from otherwise unexploited resources. Synthesis gas is generated from hydrocarbon feeds, ferro-alloys from metallic wastes, and ceramics from select inorganic species. Commercial-scale processing of multiple wastes and waste surrogates has been carried out at a destruction and removal efficiency exceeding 99.9999 wt.%, validating theoretical predictions. Unlike conventional hazardous waste treatment technologies, CEP offers resource recovery, minimal byproduct generation, and the potential for closed-loop recycling.

Jan 1, 1994

By Ennio Bonetti

The technological applications of MgH2 hydrides for hydrogen storage demand the overcoming of some critical issues: an improvement of the reaction kinetics and a reduction of the desorption temperature. The synthesis of nanocrystalline MgH2 by reactive milling and inert gas condensation and a proper metal catalyst addition, constitute recently employed strategies. In the investigation of the hydrogen short and long-range dynamics, sorption kinetics and nanostructure stability, the mechanical spectroscopy offers some specific advantages. In the present research this technique was employed with other experimental approaches (XRD DSC) to investigate relaxational and structural damping processes in nanocrystalline MgH2 with added catalysts (Fe). Time/temperature variation of the dynamic elasticity moduli and mechanical quality factor are correlated to hydrogen anelastic relaxation processes and concomitant structural transformation of MgH2 to Mg associated to long range H diffusion. Results are discussed with reference to microstructural modification strategies able to assist hydrogen release.

Jan 1, 2006

By R. D. Prengaman

Wrought lead-calcium-tin anodes developed by RSR Corporation have improved the performance compared with the other lead alloy anodes. These anodes have been in continuous service at various locations around the world for as long as fourteen years. Calcium provides mechanical strength to the anode to prevent the deformation while tin increases the mechanical strength, reduces the rate of corrosion, prevents the formation of non-conducting layers on the anode surface, and dramatically improves the conductivity of the anode. Tin is also instrumental in developing the unique rolled structure of the anode which leads to the reduced rates of corrosion, longer life, and improved oxygen evolution. Cobalt additions to the electrolyte further enhance the oxygen evolution and improve the anode life. Higher current densities and higher operating temperatures reduce the anode life. The unique patented method of attaching the rolled anode sheet to the bus bar substantially reduces the resistance of this important joint and offers the substantial savings in power over the life of anode.

Jan 1, 1999

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By J. L. Bill

The capacity of the Mount Isa Mimes Limited Copper Smelter was expanded in 1998 from 180,000 tomes per year of anode copper to 265,000 tpy. It is based on the innovative Copper ISASMELT technology, which currently treats concentrate at up to 184 tph. Increasing lance-air oxygen enrichment increased the ISASMELT furnace feed rate from 102 to 184 tph. The increased feed rate was achieved without any modifications to the ISASMELT furnace. The first refractory campaign following the upgrade lasted for two years. Future campaign lives of four years or more--without water cooling-are possible. Other Copper ISASMELT furnaces are operating in the U.S.A., Belgium, and India, with additional smelters under construction in China and Germany. In addition, Lead ISASMELT furnaces are operating in the U.K. and Malaysia. The paper discusses the performance of the MIM Copper ISASMELT furnace and the Copper Smelter since the expansion, including operating data and refractory performance.

Jan 1, 2002

By A. L. Davies

The MTDATA computer software package consists of a rigorous implementation of an algorithm for calculating chemical phase equilibria by the technique of Gibbs free energy minimization and a database of the thermochemical properties of common materials, such as slags, mattes, metals, gases and aqueous solutions. We have used MTDATA to contribute to our understanding of the chemical reactions occurring in several specific unit operations of the Kennecott Utah Copper Garfield Smelter. The following two examples illustrate the range of environments to which the method is applicable. Calculation of the liquidus phase relations of the FSF fayalite and FCF calcium ferrite slags helped in the early diagnosis of several operating problems. Calculation of the deportment of fluorine between the FSF offgas and the FSG scrubber liquor helped in the identification of operating conditions under which significant hydrogen fluoride concentrations could be introduced to the contact section of the acid plant. Without the painstaking assessment of solution phase properties undertaken over many years, these calculations would not be possible.

Jan 1, 1999

By Marcelo R. Esquivel

A MmNi5 alloy is synthesized by a combination of mechanical milling and low temperature heating processes. Synthesis time is 40 h for powders milled in a low energy ball mill at room temperature. A reduction in milling time is obtained if massive sample is mechanically milled at shorter times (2 h to 10 h) and heated at temperatures lower (600 ºC) than the usual temperatures used in equilibrium methods (>800 ºC). The alloy formation is detected even at a combination of temperatures as low as 200 ºC and milling times as short as 5 h. The temporal evolution of mechanical milling process was followed by both X-ray diffraction (XRD) and scanning electron microscopy (SEM) to detect the main stages of milling. Four stages were detected: Initial, Intermediate, Final and Completion. These stages were correlated to an enhancement of the synthesis method by combination of times of milling shorter than 10 h and temperatures of heating lower than 600 ºC.

Jan 1, 2006

By M. S. Moats

A considerable amount of research has been conducted to determine the causes of anode passivation. Chemical and electrochemical reactions that occur after passivation have received little attention. Chronopotentiometry, linear sweep voltammetry, cyclic voltammetry, and impedance spectroscopy have been used to elucidate three reactions that occur after passivation of commercial copper anodes. These involve the dissolution of silver and subsequent cementation and transformation of selenides, the oxidation of lead sulfate to lead oxide, and oxygen evolution. The amount of silver dissolution depends on the silver content of the anode, the time to passivation, and the molar ratio of Ag/(Se+Te). The oxidation of lead from PbSO4 to PbOx explains a potential plateau of oxygen evolution. Silver affects the duration of oxygen evolution on the PbOx. Anodes containing kupferglimmer display a characteristic oxygen evolution potential. It is believed that kupferglimmer provides a lower overpotential for oxygen evolution than the other slime phases or passivated surface.

Jan 1, 1999

By N. Solak

CrN, TiN and Ti-B-N coatings were deposited onto H13 hot-working tool steel and alumina substrates by arc-PVD. The coatings were characterized with respect to their mechanical and structural properties. Oxidation behavior of the coatings on alumina substrates was investigated by TG/DTA. Samples coated on H13 substrates were oxidized in a tube furnace under atmospheric conditions at specific temperatures determined from TG/DTA tests of the same coatings deposited on alumina substrates. The oxide scale morphology was characterized by scanning electron microscopy and X-ray diffraction. Oxide scale thickness change and TG data were used to calculate oxidation reaction activation energies. It was determined that boron addition into TiN coating improves not only mechanical properties but also oxidation resistance. Depending on the substrate material different oxidation activation energy values for the TiN and Ti-B-N coatings were determined revealing the importance of film morphology on oxidation resistance.

Jan 1, 2006

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By Michael G. King

The primary non-ferrous metals industry is the principal supplier of the minor metals selenium, tellurium and bismuth. It is also a major supplier of antimony. These minor elements are recovered from by-products of base metals production. To ensure that these elements remain available, the cost of production must be compatible with four other factors - method of production, available supply, technological niches, and product stewardship. This paper first describes the relationship between the copper industry and the production of tellurium and selenium. The more complex relationship between the lead industry and bismuth production is then discussed, followed by comments on antimony availability. Product stewardship programs are essential to the growth or certain specialized markets for these metals. Smelters and refineries of non- ferrous metals will play a major role in the recycling of scraps and wastes from these markets. Examples on how such materials can be recycled are given in the paper.

Jan 1, 1995

By Mahesh C. Jha

Molybdenum, a major refractory metal, is widely used as an alloying element in steels and superalloys to improve their corrosion resistance, physical properties and mechanical strength, particularly at elevated temperatures. The current worldwide production and consumption is estimated at about 130,000 tons contained molybdenum per year. Molybdenum occurs in nature as molybdenite mineral and is recovered by a flotation process as a primary concentrate at molybdenum mines and as a byproduct concentrate at copper mines. The concentrate is roasted to a technical-grade molybdic oxide (tech oxide) in multiple-hearth roasters. About 80 percent of the tech oxide is sold, as such or after conversion to ferromolybdenum, for addition to iron and steel. The remainder is further refined to pure oxide and molybdate chemicals that are used in the manufacture of catalysts, specialty chemicals, molybdenum metal and superalloys. This paper discusses the various steps in the extractive metallurgy of molybdenum, from flotation of sulfide concentrate to reduction of pure oxide to molybdenum metal.

Nov 26, 1999

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003