Search Documents

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen temary system, which is of fundamental importance for discussing the recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, Sb015 and Sb203 in the PbO-SbOu and PbO-Sb203 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By Bohumír Cech, Jirí Hanika, Václav Veselý

"PET bottles are separated and subsequently crushed into flakes. Except for PET, these flakes contain PE, PVC, paper, adhesives, beverages remainders and mineral impurities. PET itself usually is a glycol and terephthalic and isophthalic acid polymer.The suggested method consists in PET flakes crystallization at 255°C. In the meantime, volatile substances evaporate and PVC disintegrates. Formed crystalline PET is crushed into small particles and then is subject to the basic hydrolysis at an atmospheric pressure. In addition to lye solution, glycol is added in the hydrolysis. Water is eliminated by boiling, which gives rise to suspension of sodium salt of terephthalic acid and glycol. The suspension is skimmed and the filtered glycol is vacuum distilled. Pure glycol is then the distillation product.Crystals are dissolved in water and the solution is filtered, which eliminates PE and impurities. Electrodialysis removes pure terephthalic acid salt from the solution. Glycol solution is returned to the hydrolysis. Terephthalic acid is precipitated by a mineral acid. Subsequently, it is washed and dried. The filtrate is separated through electrodialysis to lye and acid. The lye gets back to the hydrolysis and the acid is used for precipitation. Terephthalic acid and glycol are products in a “polymer grade” quality. The waste is a part of washing waters, distillation residues after glycol regeneration and a filter cake after the terephthalate solution filtration."

Jan 1, 2008

By Patrick F. Mahoney

Each year in the United States over 10 million tons of metal are discarded with our municipal waste. This, includes, not only ferrous metals, aluminum and copper but gold, silver, platinum and every other precious metal. Resource recovery, as an approach to waste management, is replacing disposal and it presents great opportunities for those in the metal refining and recovery industry. Combustion of waste enriches the metal fraction left in the ash to the point where metals can be efficiently recovered. The recovery and quality of metals can be enhanced by good combustion control. Innovative technology is needed to efficiently tap this generous, and renewable mine.

Jan 1, 1995

By S. P. Marsh, M. E. Glicksman

"The effect of capillarity-driven diffusion on the recalescence of mushy zones is studied in pure materials. The solid-liquid mixture is formed by rapid partial solidification of an initially undercooled melt, and the ratio of the two phases is subsequently maintained constant by an externally imposed adiabatic constraint. A novel technique has been developed that permits tracking of the kinetics of the diffusion-controlled evolution process in situ using precision temperature measurements averaged on a length scale larger than that of the microstructure.The mean ""temperature of a mushy zone is slightly below the bulk equilibrium melting point, and is related to a characteristic length scale of the microstructure through an appropriate statistical average of the GibbsThomson equation. Theoretical considerations indicate that the diffusion controlled recalescence will progress as t- l / 3, where t is time. This behavior is experimentally verified for both succinonitrile (SCN) and ethylene carbonate (ETC), which have markedly different morphologies. The kinetic rate constant is observed to increase monotonically with increasing volume fraction of solid in the two-phase mixtures, although a firm theoretical foundation for this result has not been developed.INTRODUCTIONA dispersed multiphase system seeking equilibrium will generally contain variations in the local .free energy density. These density variations arise from such factors as variations in the bulk free energies of the phases and the distribution of interfacial energies. In this study, we examine the kinetics of diffusion-controlled recalescence in 1 solid-liquid mixture of a pure substance at its melting point. This type of two-phase system is particularly convenient to analyze because of the well-characterized physical properties of pure phases (crystals and their melts) and their interfacial energies, and the absence of any solutal effects."

Jan 1, 1986

By Zhou Jiemin

A mathematical model is developed to determine the economic thicknesses of refractories and insulations in rectangular furnaces, Both the heat loss cost and the lining investment are taken into account to achieve a minimum operation cost. For the sake of calculating the heat flux, the paper is particularly concerned with the simulation of the three-dimensional transient heat conduction processes in the lining and a Douglas-Rachford method is used to solve the finite difference equations, The model has been used to design an industrial electric resistance furnace operated periodically. the values of temperatures and power consumption measured from the furnace correspond with the model results.

Jan 1, 1991

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By K. Gao, R. Dry

"Carbon boil, which results in excessive spitting and even complete destruction of a metal drop, could significantly influence the efficiency of direct smelting processes. Carbon boil has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure, and melt area/volume ratio. The time of carbon boil was determined using a CCO camera coupled with a time/date generator connected in parallel to a video recorder and a computer. The time of carbon boil was in the range ~5 - 15 seconds under the conditions in this study. A mechanism for carbon boil has been proposed.IntroductionThe occurrence of carbon boil in molten iron drops can result in excessive spitting and sometimes even complete destruction of a metal drop. In direct iron smelting processes, this could significantly influence the decarburisation of liquid metal and the post combustion and hence may influence the efficiency of smelting processes. The generation and consequent ejection of metal droplets into the gas phase occurs due to the intense turbulence in the bath which results from the injection of gases and coal. The aim of this investigation is to understand the fundamentals governing the carbon boil phenomenon under direct iron smelting conditions to assist control of process efficiency.Carbon boil phenomenon has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure and melt area/volume ratio. The time for the occurrence of carbon boil has been determined in this study at 1440 °C using a novel approach which includes utilisation of a CCD camera coupled with a time/date generator connected in parallel to a video recorder and a computer. This arrangement permits the capture of the entire sequence of events leading up to carbon boil and therefore the determination of time of boil which is in the range -5 - 15 seconds under the conditions in this study."

Jan 1, 1996

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By Dean G. Heitt

"The Rain and SMZ mines from 1987 to 1994 produced a total of22.0 t of gold from a pre-mine reserve of 14.24 Mt of ore grading 2.13 g/t Au.Gold at Rain is hosted within the basal portion of the Mississippian Webb Formation. ·Mineralization is closely tied to the Rain Fault which is interpreted to be the main feeder for the deposit. Multiple collapse and hydrothermal breccia events provided permeability for the mineralizing fluids in the otherwise unreactive siltstones. Major alteration events include: decalcification and dolomitization of the Devils Gate Limestone; and silicification, baritization, argillization and oxidation of the Webb Fm. Six ore types based on XRD and visual rock chip Jogging have been identified: siliceous ore containing >40% quartz and <30% barite; siliceous-baritic ore containing mostly silica but >30% barite; baritic ore containing >40% barite; argillaceous ore containing >40% total clays (including alunite); calcareous ore containing mostly calcite and dolomite; and carbonaceous ore which has significant pyrite and organic carbon. Metallurgical testing of the oxide leach grade ores found that recoveries, on -1.3 cm crushed material, were greater than 70%. Results also found that Rain ore has strong grind dependency due to silica encapsulation.The Rain leach pad was commissioned in 1988, and to date 9.3·Mt at an average grade of0.65 g/t Au have been placed. Life to date recovery, through December 1995, is approximately 51 %, for a total of3.87 t of gold produced. Two major factors have contributed to the low leach recoveries at Rain when compared with the metallurgical testing: 1) More argillaceous ore than expected was placed on the pad especially late in the mine life and 2) approximately 50% of the tons placed were run-of-mine with no agglomeration."

Jan 1, 1997

By Shabnam Sabah, Geoffrey Brooks

In oxygen steelmaking, splashing and droplet formation play a key role in the kinetics of the process. Though splashing has been studied by previous investigators, there is only limited understanding of how different cavity modes affect splashing. Therefore, a cold model study (at various lance heights and gas flow rates) has been carried out focusing on the issue of cavity modes and how it affects splashing phenomenon. Analysis using Fast Fourier Transform (FFT) was carried out on cavity oscillation that showed that frequency and amplitude of oscillation was highest in penetrating mode. Measurements of splashing over a range of conditions showed splashing greatly reduced when cavities went from splashing to penetrating mode. The results were validated and compared with plant data and previous model investigations.

Jan 1, 2014

By M. E. Coleman, G. Money

"Clyde Materials Handling is an established customer-driven solutions provider, which utilizes its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets.Clyde Materials Handling has supported operators within the metals market by developing and deploying pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustainable solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes.Clyde Materials Handling has worked closely with their customers, such as Codelco in Chile, where their pneumatic solutions have been used to inject a consistent, pulseless and accurate flow of copper concentrate into a bath smelter, which has helped to fuel the operational capacity, availability and productivity.This paper will discuss and highlight the ways in which pneumatic injection technologies, created by Clyde Materials Handling, and applied in partnership with their customers, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Peirce Smith Converter.Clyde Materials Handling has applications injecting Electronic Scraps, Dusts, Reverts, and other additives to the Peirce Smith Converter. They also have experience of modified PS Units used for Slag Cleaning. There experience with the Codelco Teniente Converter is also directly related to this area of operation."

Jan 1, 2009

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By Yusuke Kimura, Ken-ichi Yamaguchi

"Secondary materials have long been processed at the S-furnace of the Mitsubishi continuous copper smelting and converting process at Naoshima Smelter and Refinery. Intensive recycling in the recent years has formed concerns that impurities in the secondary materials may cause drastic changes in the chemical properties of the CL-slag, which is separated from matte in the smelting stage. Among various impurities included in secondary materials, the authors have studied the influences of sodium oxides in the CL-slag because the behavior of sodium oxide has scarcely been studied with respect to the copper smelting slag. The examinations have been applied experimentally on the distribution between slag and matte of arsenic whose acidic characteristics suggest strong affinity to sodium-oxide of basic characteristics in silicate melts. The results have been discussed by thermodynamic evaluations and the results of pyro-tests at the commercial furnace.IntroductionAt Naoshima Smelter and Refinery, the existing line of the Mitsubishi continuous copper smelting and converting process has been operated since 1991. The Mitsubishi Process consists of three furnaces namely the S-, CL- and C-furnace as shown in Figure 1. In the S-furnace, copper concentrate and powdery secondary materials (scraps, sludges, etc) are charged through the top lances with oxygen enriched air. The other secondary materials of lumpy shapes are charged through the chute installed on the furnace roof. Charged materials are smelted by the reaction heat in accordance with the oxidization of copper concentrate. The mixed melt of matte and slag overflows through the launder into the CL-furnace, where the melt is separated into slag and matte by the difference of their specific gravity. Matte is siphoned out and sent to the C-furnace and converted to blister copper continuously. The CL-slag overflows continuously through the slag outlet to be water-granulated. Granulated slag is sold as a raw material used for the cement production and so on. Various secondary materials have been processed at the S-furnace of Naoshima Smelter and Refinery. Intensive recycling in the recent years has formed concerns that the chemical properties of the CL-slag may change drastically due to impurities originating from secondary materials. Among various impurities included in secondary materials, the authors have studied the influence of sodium oxide in the CL-slag because the impact of sodium oxide has scarcely been studied with respect to the copper smelting slag. The examinations have been applied experimentally on the distribution between slag and matte of arsenic whose acidic characteristics suggest strong affinity to sodium-oxide of basic characteristics in silicate melts."

Jan 1, 2012

By L. Yin, R. B. Haber, N. Sobh, D. A. Tortorelli, R. W. Hyland Jr.

"We optimize continuous quench process parameters to produce a desired precipitate distribution in aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include a cost function, constraint functions and their sensitivities with respect to the process parameters. These functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine a discrete precipitate particle size distribution. Both the temperature and the precipitate models are solved via the finite element method. Since we use a discrete particle size model, there are as many as 105 degrees-of-freedom per finite element node. After we compute the temperature and precipitate size distributions, we must also compute their sensitivities. This seemingly intractable computational task is resolved by using an element-by-element discontinuous Galerkin finite element formulation and a direct differentiation sensitivity analysis which allows us to perform all of the computations on a PC.1 IntroductionThis work addresses the need for an integrated design capability that links microstructure evolution to the process parameters. It is motivated by the manufacture of lightweight aluminum-alloy extrusions for use in automotive structures. Aluminum alloys offer obvious benefits, however, care must be taken to manufacture favorable microstructures that ensure acceptable structural performance. For example, the manufacturing process for 6000-series components involves hot extrusion of cast aluminum billets followed by either an air or water quench process. The bill~t's initial grain structure is dramatically altered during extrusion by massive mechanical deformations and recrystallization processes. The microstructure continues to evolve during the quench, as complex chemical processes determine the formation of precipitates. The control of the precipit'ate size distribution is vital. Indeed, large precipitates located on grain boundaries serve as crack initiation sites which adversely effect structural crash· worthiness."

Jan 1, 2000

By S. Sundarraj

The morphological transition between columnar and equiaxed structures is an important solidification phenomenon frequently observed in castings, especially complex parts with varying cross-section, The mechanical properties and the occurrence of defects such as hot tears are strongly dependent on the structure formed in the casting. Hence, it is important to understand the conditions leading to columnar or equiaxed structures. Although extensive work has been done in modeling solidification systems, almost all of the existing models are based on the assumption that the structure formed in the casting is either purely columnar or purely equiaxed. Prediction of the columnar-equiaxed transition (CET) requires a solidification model which accounts for the formation of both columnar and equiaxed structures, along with related microscopic and macroscopic solidification phenomena. In this paper a CET model is presented which: (i) takes account of both columnar and equiaxed structures, (ii) accounts for macroscopic heat transfer coupled with microscopic phenomena such as nucleation, growth and microsegregation, (iii) satisfies solute conservation, and (iv) is easy to implement in commercial finite element and finite difference software. The proposed model predictions of CET have been validated with available experimental results for a uni-directional solidification of an aluminum-copper alloy. A sensitivity analysis has also been carried out to determine the effects of various parameters on the CET model predictions. The model is being extended to other alloy systems and more complex geometries. This work will be published in due course.

Jan 1, 1996

By Takeo Fujino, Nobuaki Sato, Yarong Wang, Kohta Yamada

"Ternary mixed sulfides of some transition metals MTS3 (M=Ba, ·Pb, T=Ti, Zr) were synthesized by a relatively low temperature process using sulfur melt. The mixture of starting materials, such as, metals and/or binary sulfides and a large excess of sulfur was reacted in a vacuum-sealed Pyrex or quartz ampoule at 350- 600 °C for one to three weeks. After the reaction, the remaining sulfur was completely removed by a process composed of filtration of sulfur melt and followed dissolution in CS2• The binary sulfides impurities coexisted in the products were removed by rinsing the products in water and acetone. By using the above method, BaTiS3, PbTiS3 and BaZrS3 'Were obtained in pure form. The effect of addition of halides on the yields of these ternary sulfides were also discussed.IntroductionThere have been a vast number of studies on the preparation and physical and /or chemical properties of mixed metal oxides. As is well known, some of such compounds exhibit excellent materials properties, causing them for use in mechanical, electronic, magnetic and chemical devices. Not a few mixed metal sulfides show similar physico-chemical properties to those of the corresponding mixed metal oxides. However, the study of the mixed sulfide crystals is rather sparse mainly due to difficulties in preparing these compounds. In various methods which have been adopted for preparing mixed sulfides, the simplest method would be the solid-solid reaction of the component binary sulfides or elements. However, there are always diffusional constraints with regard to the reactions in solid phases causing it necessary to heat the reactants at sufficiently high temperatures, viz. 800-1200°C. On the other hand, some mixed sulfides are unstable at high temperatures or to change their materials properties due to sulfur nonstoichiometry and structural modification depending on temperature, i.e., synthesis of such compounds needs to be made at lower temperatures. Processing in alkali halide melts is hopeful to overcome the above problems but to obtain the halide melts the temperatures above ~ 600 °C is needed. Low temperature reaction has been carried out for the preparation of Hg1.24TiS4, which was formed by the ·combination of TiS2 and molten Hg metal at 320°C[l]. Reaction of WS2 with LiBH4 melt at 350°C yielded LixWS2[2]. These sophisticated methods, however, can be applied only to the vary special cases."

Jan 1, 2000