Search Documents

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By Hong N. Vu, Jitka Jandova

"Gypsum and limestone methods were examined in this study to process zinnwaldite wastes originating from dressing Sn-W ores mined in the Czech Republic. These wastes containing 0.20-0.30% Li and 0.10-0.20% Rb were subjected to magnetic separation to obtain a zinnwaldite concentrate with 1.36% Li and 0.94% Rb. It was observed that processing of the zinnwaldite concentrate with gypsum resulted in almost 96% recovery of Li into aqueous liquors, whilst rubidium extraction was only 25%. At the same time, it is possible to extract almost 92% Li and Rb from the identical zinnwaldite concentrate if the concentrate is processed by limestone method. Lithium carbonate, a final product of both methods was recovered from the refined sulphate solution using K2CO3 as a precipitation agent and/or from unrefined hydroxide solution using gaseous CO2. In the continuation of this study, rubidium will be separated from carbonate solutions after Li2CO3 precipitation as RbAl(SO4)2, an intermediate for Rb2CO3 production. IntroductionLithium is used as an alloying constituent in lightweight alloys, as a heat transfer medium in nuclear reactors and as a component in primary and secondary batteries. With the development of a new generation of electric vehicles, the lithium demand will dramatically grow. Lithium chemicals find extensive application in many industrial branches such as metallurgical, glass, ceramic and pharmaceutical industries. Rubidium compounds are predominantly used in psychiatry and medicine, in magneto-optic modulators, solid-state lasers, phosphors and components of electrolytes for fuel cells. The four most important lithium minerals are amblygonite, spodumene, petalite, and lepidolite. Spodumene LiAlSi2O6 (6.0-7.5% Li2O) and petalite LiAlSi4O10 (3.5-4.5% Li2O) belong to aluminosilcate minerals. Lepidolite (Li.Al)3(Al.Si)4O10(F.OH)2 (3.30-7.74% Li2O), lithium mica, is the most important representative of the mica minerals, a subgroup of the aluminosilicates. It frequently contains 3–5% Rb2O and eventually caesium. Zinnwaldite, which has the general formula K(Li.Al.Fe)3(Al.Si)4O10(F.OH)2 (2-5% Li2O), is regarded as a variety of lepidolite with a high iron content. Commercial amblygonite is a complex phosphate (Li.Na)Al(F.OH)PO4 (up to 9.88% Li2O), however, its deposits have not been commercially exploited because of their small size. Natural brines with a high lithium chloride content are important in the industrial production of lithium [l]"

Jan 1, 2008

By Andreas Stieben, Pierre Lutomski, Wolfgang Bleck, Martin Fischer

"For steel investigation and development, exact knowledge about the microstructural state is required. The information gained from 2D images often can't properly reflect the real 3D microstructural properties. In order to gain reliable information for meaningful models, simulations and correlations, it is necessary to accompany standard metallography with 3D information, which, unfortunately, is very difficult to access. This article presents a procedure for serial sectioning in combination with light optical microscopy. Only standard metallographic tools are employed in combination with image manipulation freeware. 3D microstructural data were extracted from three multiphase steel grades and in two cases virtual 3D-models of microstructural phases were generated.Three Dimensions Of MicrostructuresSince the invention of steel, craftsmen, inventers and engineers tried to improve its properties and tailor them to the requirements of new developments. For systematic development and enhancement of steels, the capability to investigate its inner structure is highly important, because it represents the linchpin between material production and properties. By having an in-depth understanding how production conditions form the microstructure and also how the microstructural state determines the material properties, steel design can be drastically improved. With this knowledge, microstructures can be designed to provide target material properties and process conditions can be identified that form these structures. Due to the key role of microstructure, the capability to gain accurate information about it is indispensable. It is the task of metallography to access and extract descriptive quantitative microstructural data like fractions, sizes, shapes and distributions of the different constituents. The most commonly used investigation tool in metallography is the light optical microscope (LOM). Besides this tool, additional high resolution techniques like Scanning Electron Microscopy (SEM) or Transmission Electron Microscopy (TEM) have become increasingly important. With these and other available methods, extensive information on the microstructural state of a material can be gained. Unfortunately, most metallographic methods have a major loss of information systematically built in. Analyses of microstructures are usually performed on surfaces, i.e. on 2D areas that emerge by cutting through the 3D material structure. This means, a complete dimension of information is not taken into account. How serious this reduction of information is and how it can affect interpretation of structures is exemplarily demonstrated in figure 1, which displays the planar structure emerging from a random cut through a simple 3D structure. It is very difficult to deduce or even imagine the original spatial structure from which this projection emerged and it is impossible to reconstruct it with absolute certainty without further information. The image has emerged from a random cut through a 3D structure of stacked cubes that is displayed in figure 2. The area shown in figure I is outlined. Although artificially constructed, this example demonstrates how distorted and misleading the view on structures can become by ignoring a spatial dimension."

Jan 1, 2012

By S. I. Sobol

The results of the study of the mechanism of a cathode process of cobalt electrolysis to explain disagreements in a form of kinetic equations of autoclave reduction of nickel and cobalt have been used.

Jan 1, 1993

By John M. Boyle

The use of high vacuum mercury retort recovery as a safe and effective means of removing mercury from mercury hazardous waste solids rendering them non-hazardous and recovering mercury suitable for recycling.

Jan 1, 1995

By Shaolong Chen, Carl-Gustav Berg, Hannu Mansikkaviita

Kumera Steam Dryer has been developed particularly for nonferrous metal concentrates with steam as heating source generated from waste heat boilers. Its unique structure enables the dryer to work at high capacity, up to 240 t/h, and high availability, over 95%. With half a century of engineering experience, and more than twenty industrial steam dryer installations worldwide during last 15 years, Kumera has demonstrated significant benefits of the steam drying technology in terms of energy efficiency and emission reduction to the end users. The dryer of this type can also be applied for other suitable mineral materials.

Jan 1, 2015

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi-industrial scale experimental system. Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/cm3 has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/cm3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition of the car engine.

Jan 1, 2003

By C. L. Kusik

Environmental issues are having a significant impact on how automobiles are designed and ultimately disposed of at the end of their lives. On one hand, increasing concerns about landfill disposal have resulted in greater attention being focused on recycling materials and components from old junk autos. On the other hand, corporate average fuel economy (CAFE) requirements have led to downsizing, use of coatings, materials substitution and other measures that often make recycling more difficult. Automobile makers have responded to Corporate Average Fuel Economy (CAFE) Standards in a variety of ways such as: Downsizing; Designing of more fuel efficient engines; Reducing aerodynamic drag by sleeker body designs; Redesigning by using thinner gauges of coated steels; and Substituting material such as lightweight plastic or aluminum parts for steel. Other driving forces affecting production techniques, choice of materials and recycling issues include the Clean Air Act and its amendments, RCRA. and other environmental legislation. The variety of materials used in automobiles makes the recycling issue extremely complex. Not only does one have different materials used in different automobiles for making similar parts, but changing designs, evolving environmental issues, landfill closures affecting solid waste disposal, and increasing raw material quality standards have created a complex set of dependencies related to materials use and recycling.

Jan 1, 1994

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Byung-Su Kim

The reaction between calcium sulfate and hydrogen is of interest both as a means of regenerating calcium sulfide as a reductant of sulhr dioxide to elemental sulhr and for producing elemental sulhr from gypsum. This reaction was investigated using a thermogravimetric analysis technique in the absence and presence of nickel catalyst. The reaction temperature was varied between 973 and 1153 K, while the hydrogen partial pressures of 12.9 - 86.1 kPa were utilized. At 1073 K and a hydrogen partial pressure of 86.1 kPa, 60 % of the original calcium sulfate in the absence, and 95 % in the presence, of the nickel catalyst was converted to calcium sulfide in one hour.

Jan 1, 1999

By Balasivanadha Prabhu, Prasad P. Shanmugasundaram, Narayani Narasimhan

"The grain refinement and mechanical properties of 6061 aluminium alloy produced by equal channel angular pressing (ECAP) have been analyzed in this present study. A innovative triple shear ECAP die was developed for the processing.It was observed that the grain refinement takes place for greater number of passes. It was also found that reducing the process temperature gives fine grain and high microhardness and hence improved propertiesIntroductionTechnological changes in manufacturing industries have depended heavily on development in materials processing and process technologies. Modem industries need high performance materials for severe service conditions. Hence, it is necessary to improve required material properties to achieve better performance and greater service life. As mechanical properties of the materials strong! y depend on grain size ( d) - Hall-Petch relationship [ 1-4], the ultrafine grained (UFG) materials offer superior mechanical properties based on the above relation.Synthesising massive nanocrystalline materials presents a challenge to basic research as well as to application-related processing efforts. Production of ultrafine gram microstructures in metals and alloys having different crystal structures but always an initially coarse microstructure using severe plastic deformation can significantly enhance the physical and mechanical properties of materials. Severe Plastic Deformation (SPD) is an efficient method to induce ultra fine grained structure in materials by deforming it to large strains. Traditional techniques for introducing deformation of higher strains, such as forging, extrusion, drawing or rolling do have the inevitable limitation on required equipments of exerting enough load or pressure to cause uniform nanometer level grain refinement."

Jan 1, 2011

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By G. T. Lapidus

One of Society’s major concerns with hydrometallurgical processing is the large amount of water that is quintessential to its nature. This is especially troubling in arid areas, where the population struggles to procure potable water for their daily needs. For that reason, it has become our responsibility to conceive, design and implement processing schemes that not only use as little water as possible, but recycle streams within the plant itself and minimize waste that exits its perimeter. With this in mind, the conference will center on the importance of selecting the appropriate chemical systems and integrating material balances to avoid reagent overkill and to detect impurity accumulation. The three “R’s” (reuse, recycle and recovery) of aqueous solutions within the processes are emphasized. Examples of processes for the recovery of lead, copper, precious and PG metals from minerals and waste materials will be presented.

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By Ilona Johnson

United States metals and non-metallic minerals manufacturing consume about 5,000 trillion Btu annually. Various studies estimate that as much as 20 to 50 percent of this energy is lost as excess or waste heat. Recovery of waste heat can conserve energy, reduce operating costs, and lower environmental emissions. It would be valuable to quantify recoverable waste heat sources and identify the barriers that hinder its recovery. This paper provides an overview of waste heat losses specific to high temperature processes in primary metals and minerals manufacturing. It summarizes findings from a broader study conducted for the Department of Energy Industrial Technologies Program; the study evaluates energy losses, recovery practices and opportunities, and R & D needs for waste heat technology development.

Jan 1, 2008

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011