Search Documents

By J. B. Wiskel, H. Henein

"A study was conducted to establish the effective heat transfer coefficient for a single molten droplet moving in a gaseous medium. Towards this objective, a series of quench experiments were performed on molten droplets of AA6061 aluminum generated with the Impulse Atomization technique (IAP). IAP is a single fluid atomization process capable of producing powders with a predictable mean particle size and a relatively tight standard deviation under controlled atmospheric conditions. Microstructure analysis of the atomized powder was used to establish the extent of pre-quench solidification. A mathematical model was then employed to correlate the Ranz-Marshall and Whitaker equations with the observed particle cooling behaviour. These equations were found to provide a reasonable estimation of the heat transfer conditions only when the variation in gas thermophysical properties across the boundary layer was accounted for in the model. This model formulation of droplet heat transfer has important implications with regards to active sprays and atomization processing operations IntroductionAn understanding of droplet cooling is important in atomization powder production. It is well understood that dendrite arm spacing is inversely proportional to cooling rate during solidificationl1l. Through modification of the heat transfer conditions during metal atomization, the microstructure of a powder maybe tailored to the end user. However, owing to the complexity of gas flow it is difficult to determine a heat transfer coefficient for a moving droplet. This difficulty is further compounded when complex jets and/or streams and their interactions are considered. To provide a base for these more complicated types of analyzes, two approaches have been employed to calculate the effective heat transfer conditions for a single droplet. In one approach, Megardis [ZJ developed a numerical model to investigate the heat transfer process of a free falling droplet undergoing laminar convective cooling. The effective heat transfer coefficient as a function of angular position was determined by numerically solving the fluid and energy equations for the system."

Jan 1, 1999

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By William James Middleton

The life-cycle assessment (LCA) approach can be an important tool for the quantification and evaluation of environmental impacts associated with metal production systems. At the conceptual phase of a new metals development project, LCA can: ? Aid project decision making by evaluating the environmental consequences of design decisions ? Support project permitting and reinforce site/process environmental impact assessment ? Allow environmental impact comparisons between alternate flow sheets For existing metals production systems, LCA has been used to aid targeted process improvements by monitoring recent historical trends in environmental performance, either through local or external (externalities) process improvements. This paper discusses the life- cycle assessment methodology, and its application as a supportive tool for environmental decision-making in process design and operation, and for site environmental impact assessment and permitting. Selected examples from a recent LCA performed on the Pressure Acid Leach Process for treating nickel Laterite ores are employed to demonstrate the usefulness of the tool.

Jan 1, 2004

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By C. E. Hunt

Since the turn of the century, copper-nickel sulphide ores have been processed at the Sudbury, Ontario operations of INCO Limited, currently the largest integrated mining, milling, smelting and refining complex in the free world. Through the years operational, ecomomic, social and legislative changes have dictated the need for research and development directed at mitigating the impact of existing operations on the surrounding natural environment and also the reclamation of areas affected by earlier mining activities. Approximately one hundred years of mining history and the current annual processing of some 12 million tons of ore presents significant challenges with respect to waste disposal, liquid effluent treatment and land reclamation, particularly in light of rapidly evolving environmental regulations' and controls within the Province of Ontario.

Jan 1, 1992

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By Tuneo Funahashi

Sumitomo Shisaka Works has been treating EAF(Electric Arc Furnace) dust to recover zinc and lead in the Waelz Kiln process. Since its commencement of operation in 1977, many technical improvements have been successfully made to increase the production capacity and the zinc recovery rate. The EAF dust charge to the Waelz Kiln was increased from 35,000tly to 120,00OtIy, and the production of zinc oxide now amounts to 40,000tly. The zinc content in the clinker was decreased from 5% to less than I%, by the optimization of the kiln heat pattern with no accretion trouble. And the clinker has become more a valuable raw material for steel making. This paper describes the above progress ofthe SMM Waelz Kiln process operation at the Shisaka Works.

Jan 1, 1998

By Charles W. Kenney

Mercury contamination of soil at an old chemical plant surrounded by a residential community and adjacent to a river has provided unique challenges for the current owner. Inorganic and organic mercury compounds had accumulated over the past 50 years to levels that require remediation. Hazen Research, Inc. conducted a multi-phased program to characterize contaminants and their occurrences, evaluate various treatment technologies, and demonstrate the selected technology at bench and pilot scales. A combined physical cleaning and chemical treatment was demonstrated to meet treatment goals for the site. This paper discusses the methods of process selection and results of the bench-and pilot-scale testing.

Jan 1, 2003

By Xiao-hui Fan, Xu-ling Chen, Xiao-xian Huang, Gui-ming Yang

Grate-kiln-cooler is a predominant process of producing iron ore pellets in China. Since this process is of multi-variant, strong coupling and large hysteresis characteristics, a reliable performance monitoring is thus essential to ensure product quality and economic benefits. Aiming to efficiently monitor the pellet induration within this process, this study proposed an approach that combines statistical analysis and quality soft-measurement. Soft-measurement of pellet quality was accomplished based on the predicted time-temperature profile, and the soft-measured indices were on-line monitored using statistical control charts. Based on the proposed approach, a monitoring system for grate-kiln-cooler thermal process was developed for a domestic pelletizing plant. Running results demonstrate that our system can assist in the detection or diagnosis of abnormal thermal state and finally helps to stabilize the pellet production.

Jan 1, 2016

By H. -P. Behrendt

Muldenhiütten Recycling und Umwelttechnik GmbH is a lead smelter with a very long tradition. The first reference to the existence of smelters on this site is given by a document of inheritance dated 1318. Originally run as a primary lead smelter, which was supplied with ores from the Freiberg mining district and from overseas, it was required to change it over to secondary raw materials due the abandonment of mining in the Freiberg area in 1968. Today, Muldenhüitten Recycling und Umwelttechnik GmbH has two production lines; lead production from secondary lead and waste incineration, which are closely connected and gain advantage from each other. Installations, improved technologies, and the highly skilled personnel have contributed to satisfy all demands for a production concerning quality and environment.

Jan 1, 2000

By Claudio Toro, Alex Moyano, Rodrigo Díaz, Hugo Jara, Carlos Caballero, Pedro Morales, Leandro Guzmán

"During 2007, Codelco-Chile carried out industrial tests to validate the Continuous Converting Process in the Teniente Converter of the Codelco Norte smelter.For planning and starting up the tests, a predictive, analytical and dynamic model was developed to support operational decisions. The dynamic model was developed using the METSIM® platform and dynamic data exchange (DDE) to operate smoothly with MS Excel®. The main feature of this real-time model was the on/off-line ability to work and gather data from either the smelter’s PI system® or database, and simulate the operation with or without scheduled events and controls.The main model development aspects, which include thermodynamics, metallurgical and kinetic considerations, slag-type and on-line mass and heat balances of the process, as well as the successful validation of the model, are presented and discussed in the present paper."

Jan 1, 2009

By G. Bjorling

After complete dissolution of chalcopyrite concentrate in sulphuric acid in presence of nitric acid the excess of the latter is expelled by a surplus of concentrate and the last traces of nitrate removed in the mother liquor after crystallization of the copper and iron sulphates. Zinc accumulates in the mother liquor from which it can be removed by solvent extraction of zinc sulphate as a pair of ions. After dissolution of the sulphate crystals in water the neutral solution is oxidized in an autoclave at 140°C where iron sulphate is thermally hydrolyzed; the iron-free solution is taken to copper electrowinning and the cell acid after partial evaporation recirculated with the mother liquor to the leaching circuit. Total recovery of copper is about 96%; other metals like zinc and iron are concentrated in industrially usable products. At a copper price of about 70 c/lb, the method appears to be profitable also in a small unit.

Jan 1, 1976

By Tabbetha A. Dobbins

We report studies concerning the time frame for catalytic reactions between NaAlH4 (sodium alanate) and TiCl3 during high energy milling. Spectral features in x-ray absorption spectra were analyzed for samples milled for various times (0 minutes, 1 minute, 5 minutes, 25 minutes, and 125 minutes). A structural transition from Ti3+ to Ti0 is observed within the first 5 minutes of milling. The Ti0 structure persists for samples milled for times longer than 5 minutes?even after those samples underwent a subsequent single hydrogen desorption/absorption cycle. Samples milled for less than 5 minutes retain Ti3+. For samples milled for 1 minute, the Ti-K edge position shifts from Ti3+ to Ti0 after a single desorption/absorption cycle. However, the first coordination sphere around the Ti0 absorber occurs at longer distances for 1 minute milled sample. These results hint at the formation of Ti0 pure metallic clusters upon desorption/adsorption cycling of 1 minute milled sample. Previously reported x-ray absorption spectroscopy studies have demonstrated the structural transition from Ti3+ (in TiCl3) to Ti0(determined to be TiAl3 found at the surface of the alanate powder). Aluminum deficiency on the NaAlH4 lattice is responsible for controlling hydrogen absorption capacity. These time-resolved spectroscopy studies suggest the possibility for controlling aluminum deficiency, while still maintaining titanium activation of the alanate powder, by manipulating the coordination environment of the titanium dopant during the first five minutes of high energy milling. Specifically, a possible approach to mitigating aluminum deficiency during doping would be to introduce an alternative species to which the to Ti3+ catalyst would form a metallic bond after the TiCl3 has attached at the surface of the sodium alanate powder and before the Ti3+ forms the TiAl3 intermetallic species.

Jan 1, 2006

By Jose Lara

SIDOR has developed a setup model for a roughing mill with edger that optimizes the position of the edger for a better control on the width, optimizes the efficiency of the mill for controlling of the profile of reductions and increments of the speed rolling and improves dimensional performance. This model consider as data entry, the number of passing, incoming and finish thickness and width, hardness and temperature of the material. The setup model is based on the equations of Ekelund for the width spread calculation and estimates of the rolling force. Additionally this model employ a Newton's algorithm for resolving the optimal position of the edger. The preset values calculated by setup model is the horizontal screw position, vertical screw position (edger), threading and rolling speed, some parameters calculated for the correction of ski. In the revamping of the roughing mill of hot rolling of SIDOR, C.A, carried out in January of 2005, it was implemented this setup model and the coefficients and parameters were adjusted for the first 15 days. Starting from there the values of preset, send to roughing mill are calculated by this setup model. The current indicators show an enhancement of 18% in the roughing mill effectiveness and a decrease about 37% in the mill stop by overload in the motors.

Jan 1, 2006

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By N. Verbaan, E. Bourricaudy, M. Dry

"Starfield Resources is developing a novel circuit for the recovery of nickel, copper, cobalt, iron oxide, sulphuric acid and precious metals from the Ferguson Lake deposit in Nunavut, Canada. In this deposit, pentlandite is too finely disseminated in pyrrhotite for the production of a smelter-grade nickel concentrate at an acceptable nickel recovery, so established technology is not applicable and a novel chloride-based circuit is under development. The enabling aspect of this circuit is the hydrolysis of ferric chloride to hematite, releasing gaseous hydrochloric acid that is recycled. Conventional steps are used for separating and recovering the valuable metals from the chloride solution generated. This paper briefly outlines the circuit and presents the results of experimental work on the enabling steps, viz. the oxidation and hydrolysis of iron chloride to hematite and gaseous hydrochloric acid.IntroductionThe Ferguson Lake bulk sulphide ore body in Nunavut, Canada, owned by Starfield Resources Inc., contains significant amounts of base and precious metals but its mineralogy is such that it is not amenable to conventional processing. Pentlandite, for example, is too finely disseminated in pyrhhotite for even modem techniques such as fine grinding and improved flotation reagents to be effective [ 1] and extracting the value requires processing the entire bulk sulphide, including the pyrrhotite. To give the project a total green footprint, in terms of both carbon emissions and acid rock drainage, Starfield imposed the following requirements:• No reactive tailings to generate acid rock drainage.• No gaseous emissions other than normal atmospheric constituents.• No liquid effluents.• No regular consumption of fossil fuel.• High recoveries of all the valuable metals."

Jan 1, 2011

By V. Gel

An analysis of the operation of rotary tilting furnaces has indicated that they ensure better recoveries of metal when smelting lump scrap from aluminum slags, brass and bronze. On the other hand, processing of slags (concentrates obtained by mechanical upgrading) in pear-shaped furnaces results in much lower performance values as might be expected. At the Novgorod metallurgical plant a process for blister copper production in a rotary TROF converter (Outokumpu, Finland) has been introduced on a commercial basis. Smelting of brass and bronze scrap to produce blister copper is carried out using the technology developed in Russia and differing from the Outokumpu technology by the types of flux used and the blowing conditions in fuel burners and for melt oxidation, as well as by the design of gas removal system, the design of nozzles for melt blowing and the use of carbonaceous reductant (coal) for magnetite reduction in slags. Industrial-scale testing has demonstrated that by means of special techniques the 30-tonne converter productivity can be increased by 30% to 40% as compared with its rated productivity.

Jan 1, 2006

By K. Fukushima, K. Baba, H. Kurokawa, M. Yamagiwa

"The Toyo smelter has expanded its anode production capacity from 126,500 to 239,000 t/year by introducing technical oxygen into blast air for flash and converter furnaces and improving smelting facilities. Significant efforts were made in the expansion not to increase the number of workers, which mean development of some automation systems for the copper converters and anode casting wheel. The efforts have resulted in the above-mentioned increase in productivity and a saving of production cost as well as a decrease in the number of workers for the anode casting operation.IntroductionThe Toyo smelter has been performing a highly stable and pollution free operation since its commencement in 1971 (1). Its distinctive features are the on-line control by process computer (2) and the high productivity without trouble. But owing to the so-called oil crisis in 1979, we were faced with a sharp increase in production cost. To decrease the production cost, some measures for saving of energy were planned and carried out, such as conversion from oil to coal in a flash furnace (3), the heat recovery from converter slag and the introduction of technical oxygen in blast air with the intention of energy saving as much as possible.The first increase in production capacity and some savings of production cost were attained in 1982 by the introduction of technical oxygen in blast air for the flash furnace without major modification of the furnace as shown in Table I. The capacity of an oxygen plant is 7,800 Nm3/H as 90% O2 . Part of oxygen from the plant is also supplied to tuyeres of copper converters through an oxygen holding tank with a volume of 830 m3 at 7 kg/cm2-G."

Jan 1, 1989

By Cameron Harris

With the consolidation of the copper industry in the second half of the 20th century resulting in fewer plants treating ever increasing quantities and qualities of feed, the enormous flexibility of the Noranda Process gives it significant advantages over many competing technologies for the production of matte. Toll smelting, recycling, and secondaries treatment will become the cornerstone of profitable operations for all but the lucky few who have large captive mines associated with the smelter. Consequently, the ability to respond to changing market conditions without significant metallurgical or operational upsets will be of considerable commercial advantage. The inherent stability of this bath-smelting process leads to tight matte grade control, while the bath turbulence leads to rapid consumption of feeds with widely varying physical characteristics. Low capital and operating costs combined with a layout suitable for retrofit into existing converter aisles makes it a sensible choice for parts of the world still experiencing the aforementioned consolidation, which is essentially complete in fully developed economies such as the United States of America and the European Union. This paper will discuss features of the Noranda process compared with other technologies and its place in the future global copper production industry, which is set to become increasingly competitive and aggressive.

Jan 1, 2002