Search Documents

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By Arvind Thekdi, Cynthia Belt2

"Waste heat from industrial operations in metals industry represents 20% to 50% of the total energy used in most manufacturing plants. Reduction and recovery of waste heat offers the most attractive and cost effective method of reducing energy intensity for an industrial plant to meet corporate energy saving goals. It is possible to reduce or recover 30% to 60% of the available waste heat by using conventional and readily available technologies. Projects to reduce or recovery waste heat may offer less than 3 years payback to as short as a few months. This paper presents information on most commonly used methods for waste heat reduction and recovery in the metals industry operations. It describes the methods and use of analysis tools that would allow a user to estimate energy savings, CO2 or GHG reduction potential, and economic benefit and includes appropriate case histories.Waste Heat SourcesSources of waste heat abound with the metals industry. While the overall quantity of energy is high, the sources are distributed throughout a plant. The largest source within the metals industry is within furnace exhaust / flue gases. This includes the high temperature gases from burners in process heating such melting, calcining, and sintering operations. It also includes lower temperature gases from heat treat, dryers, and heaters. Lower temperatures are also found after post processed hot gases. This could include heat left after heat exchangers, regenerative systems, thermal oxidizers, and emission control systems. Other hot gases include air used in direct and indirect cooling.While waste heat in form of exhaust gases is readily recognized, waste heat can also be found within liquids and solids. Waste heat within liquids includes things such as cooling water, heated wash water, and blow down water. Solids can be hot product at discharge after processing or reactions are complete. Indeed, not only is energy wasted in the hot metal that slowly air-cools, but additional energy may be used in providing air or water-cooling to increase the speed of cooling. Other waste heat sources are not as apparent and include things like hot surfaces, steam leaks, boiler blow down water, etc. Table 1 and Figure 1 show several major sources along with the temperature range and characteristics of the source."

Jan 1, 2011

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Melvin A. Jennings

Ion-exchange technology for precious metals recovery is at a turning point. Some very exciting technology has been developed in the past five years which should lead to commercialization of the process. Ion-exchange will allow not only for the recovery of gold and silver, but also will allow for the recovery of cyanide form plant tailings. This process may soon be competitive with Merrill-Crowe for silver and once this occurs, it will become the process of choice.

Jan 1, 1991

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By Fan Xiao-Hui, Jiang Li-Juan, Chen Xu-Ling

"In order to solve air leakage of sintering testing cumbersome, inaccurate results, and other issues, the sinter machine air leakage characteristics were studied, and combining the mathematical modeling and the field detection. The temperature before air leakage was calculated by mathematical model, energy balance equation was established according to sintering process, using Adams prediction correction method which has stronge stability and high precision, to solve hyperbolic partial differential equation with astringency problem. The temperature after air leakage is detected by instruments, according to energy conservation calculation the sintering air leakage rate. According to the sintering continuity and periodicity, sintering air leakage location diagnosis expert system was established to judge specific air leakage locations.IntroductionStrengthening of modern blast furnace production depends on the quality of the raw material preparation to a large extent [1]. Technical and economic index of modern blast furnace production is advanced; the most important reason is the use of concentrated feed. Sintering plant is the ""kitchen"" of blast furnace’s concentrate. As we all know, sintering plant is major energy consumption of steel plant, in sinter process energy consumption, the solid fuel consumption of total energy consumption is 75%~80%, power is 13%~20%, ignition and combustion is 5%~10%. To reduce the air leakage of sintering plant is an effective measurement to save energy consumption. At present, our air leakage of sintering compared to the other developed countries is still a long way to go. Japan’s air leakage rate is about 30%, and 35%~60% air leakage of sintering machine at home, a big gap exists between the plants. At present the determination of air leakage is all for manual operation, long measuring period, considerable manpower and resources, and the results are significantly affected by operation. For air leakage of sintering control lag issues, research and development of diagnosis expert system for on-line monitoring model for air leakage and, through this research can reduce the use of detection equipment, detect sintering air leakage, improve the yield and quality of sintering production, reduce energy consumption, and extend equipment life span."

Jan 1, 2012

By Jukka S. Sulanto

Outokumpu has applied its well -known copper Fl ash Smelling Process also for smelting su1phide lead . concentrates. The lead in the Flash Smelting Furnace slag is recovered by reducing the oxygen potential of the slag in an electric furnace by injecting reductant into the slag bath. A series of tests have been carried out in a 1000 KVA electric furnace? adjacent to a pilot Flash Smelting Furnace. The furnace has been fed continuously with molten Flash Furnace Slag. The feed rate has varied from 0.5 to 3.1 MTPH (0.55 - 3..4 STPH) depending on the feed rate and the quality of concentrate to the Flash Smelting Furnace. The inlet slag contained 15 to 40% of lead and the cleaned slag 1. 5 to 3. 0%. The lead recovery from sol id raw material was tested in the same continuous process by feeding lead calcine into the furnace. Feed rate was 0.7 to 0.95 MTPH (0.8 - 1.05 STPH) and the calcine contained 33 to 34% of Pb. Several reduction agents and procedures were tested. The process proved to be suitable for continuous recovery of lead from solid oxide raw materials.

Jan 1, 1990

By B. W. Lightfoot, Neill F. Arthur

"The AusIron process is a new development of the well established Ausmelt bath smelting technology(l). The development of this technology has been tied to the South Australian Steel and Energy (SASE) project which brings dedicated coal and iron resources together with this new technology. SASE is a joint venture between Ausmelt (40%), Meekathara Minerals (40%) and the South Australian Government through Mines and Energy South Australia (MESA) (20%). It will use a multiple lance furnace to process iron ore using steaming coal for both fuel and reductant.It is intended to build the simplest plant economically possible. Refinements such as preheating and prereduction of the ore are compatible with the technology but are not expected to be necessary in the first generation plant.The joint venture is negotiating with suitable partners for funding of the project through to commercial implementation at a target scale of2.5 mt/a of pig iron.ObjectivesAusIron aims to produce pig iron directly from steaming coal and from any of a variety of iron sources in a simple furnace system with a minimum of pre-processing of either coal or iron ore. Preheating and prereduction of ore are compatible with the technology but may not be necessary. The immediate aim is not to be the technology that uses the least quantity of coal to produce iron metal but rather the technology that uses the least number of dollars to produce metal.The chemistry of iron making is well known, probably better known than that of smelting of any other metal. Iron has been made for thousands of years and it is possible to make iron from charcoal and ore in a simple blast furnace the size of a beer barrel. The focus is therefore not making iron but rather making it more cheaply than it is made by current technologies. Large blast furnaces now set the standard and new technologies must perform better if they are to gain market share. It is still the cost of iron, energy units and capital going into these mega blast furnaces which ultimately set the market price for pig iron."

Jan 1, 1996

By Tullio Corsini

Scrap battery recovery process, developed by Engitec Impianti S.p.A., is improved transforming batches operations in continuous. Benefits expected: constant and better quality of the products; easier and more reliable control of the operating parameters, reduction of manpower requirements. Paste will content less sulfate, particularly in soluble form. Sodium sulphate is obtained with higher and constant purity.

Jan 1, 1993

By Christine P. Viecelli

As Phelps Dodge Corporation addresses the environmental challenges of the 1990's, water management has become a key element in an overall waste minimization strategy. The Phelps Dodge Hidalgo copper smelter has implemented a comprehensive water management program that includes management of both fresh and process water utilized by its pyrometallurgical operation. Two major technological strategies are being implemented. They are the design, construction and operation of a raw water pre-treatment facility to allow increased evaporation within cooling towers thereby minimizing blow down, and the use of a brine concentrator to treat and recycle significant quantities of process water. The end result of this program is a significant reduction in raw water pumped from the underlying aquifer into the facility as well as a decrease in process water which must be impounded or otherwise treated.

Jan 1, 1992

By J. Partinen

Drying is a unit process which has numerous applications in metallurgical process industry. Kumera Technology Center, being a worldwide equipment and process supplier, has developed sophisticated solutions for both direct and indirect drying. In conventional direct drum drying, the energy is taken from combustion of fossil fuels, requiring energy input and emitting considerable amount of off gases. In modem copper smelters, thermal energy from the off gases is recovered in waste heat boilers making the steam available. Using that steam as the energy source for concentrate drying, the total volume of off gases can be considerably reduced and releasing of harmful combustion gases into the atmosphere can be avoided. Kumera Technology Center has recently developed and promotes a new steam drying process for drying of copper concentrates. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the steam dryers and the drum dryers. In the design special attention has been paid to overcome problems of excessive wear and clogging and to reduce the required maintenance operations. In this paper the environmental issues and energy consumption related to both direct and indirect drying processes are discussed. The estimated operation costs and emission levels are compared, based on calculations and the data collected from industry. Finally, the development project of the Kumera Steam Dryer is briefly reviewed

Jan 1, 1999

By T. N. Chan

This paper provides some general discussions on the development of a new beneficiation process for the treatment of a highly complex monazite orebody located at Mt Weld, Laverton, Western Australia. The complexity of this rare earth ore and the associated problems encountered in ore preparation, desliming and flotation in beneficiation during the development study stage and the solutions to these problems are reviewed.

Jan 1, 1992

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By K. Takahashi, G. Dodbiba, T. Fujita, N. Sato, S. Matsuo, K. Okaya

Different materials are used for manufacturing various parts of a cellular phone. Considering that a great number of mobile phones are being discarded every year, it is important to recover these materials and then recycle them in order to save resources. The primary objective of this work is therefore to find and suggest ways on how to recover various materials from discarded cellular phones for recycling. Much effort, for example, has been put in recovering and recycling tin oxide (ITO), a mixture of indium (III) oxide, (UI2O3) and tin(IV) oxide from the discarded liquid crystal displays (LCDs). Here we report a simple and cost-effective process, which includes a HC1 treatment process for altering the structure of the indium (III) compound into a chlorideinduced indium compound, in order to facilitate the vaporization of indium at a relatively low temperature. The experimental results indicated that 96.2 % of indium can be recovered from ITO, when the sample was heated at 973 K for 90 minutes. In addition, some thermodynamic calculations were also carried out in order to better understand the mechanism for chlorideinduced vaporization of indium.

Jan 1, 2011

By S. B. Breyner, A. Ressler, D. Gregurek, A. Spanring

"The changes in process conditions that frequently decrease the service life of refractory products provided incentive for RHI AG to develop high performance bricks, especially for non-ferrous metal applications. Innovative product development was required to determine suitable refractory products for improving lining life. At the Technology Center in Leoben, Austria, practical corrosion testing methods and facilities, including an induction furnace and rotary kiln, enable detailed comparative analysis of brick wear on a pilot scale. In tests that were carried out using a fayalite type slag, the newly developed RADEX VFG magnesia-chromite grade showed very promising results compared to the standard grades. Based on the test results, optimal refractory solutions can be recommended for this challenging industrial application and field trials can be performed directly at the customer's site.IntroductionThe complexity of metallurgical processes in the non-ferrous metal industry, and especially changes to the process conditions in combination with the diversity of metal processing furnaces ''', requires a precise understanding of each individual system for appropriate refractory product selection l2'. In addition, particular importance is focused on the specific refractory consumption being as low as possible.Another important aspect results from the global shortage of resources, which forces companies to invest in recycling processes. In the base metal industry, recycling operations have resulted in significant changes; for example, operating with two slag chemistries and process temperatures will influence the performance of previously suitable linings. The raw material mix for primary smelters has also changed, including higher levels of secondary raw materials in the smelter feed."

Jan 1, 2012

The increasing need for robust pyrometallurgical furnace construction is driven by two trends in the copper and other base metals smelting industry: ? the desire for increased production within a single furnace line by greatly increasing smelting intensities, which generates high heat fluxes to the crucible. walls, and ? the operational and economic imperatives of maintaining high percentage on- line times and long campaign lives between rebuilds. A key feature of furnaces capable of producing at high rates, while containing intense processes, is a strong, thermally robust wall cooling system. Equally important design aspects include the furnace steel structure, refractories, a cooling water supply and piping arrangment for safety from leaks and disruptions, and instrumentation/controls for monitoring and rapid mitigation of process excursions. Integration of the cooling elements into these furnace systems is essential for optimum performance of the cooling elements, and indeed the entire furnace. This paper discusses the development of a composite copper / refractory water- cooled design, which has been successfully implemented on several copper smelting and converting furnaces, including Kennecott's flash converting furnace, INCO's MK reactor, and Kidd Creek's converting furnace.

Jan 1, 1999