Search Documents

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By Gregory Molinda

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3 way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

Jan 1, 1998

By Samrat Mohanty

The construction of underground hydrocarbon storage caverns in Jurong Island, Singapore, is nearing completion. The facility, located beneath the seabed of Banyan Basin, is comprised of five storage caverns with a storage capacity of approximately 1.5 million cubic meters. The galleries of each cavern are 20 m wide by 27 m high and approximately 340 m long. In addition to the storage caverns, various access and operations tunnels are required to support the facility. Among these are water curtain galleries to ensure that hydrostatic pressures in excess of hydrocarbon storage pressure are maintained in the rock mass surrounding the storage caverns. Early in the design process, conventional steel rock bolts with resin polymer grout were considered for ground control. However, the construction contractor proposed using fibe-reinforced polymer (FRP) bolts with cement grout due to the corrosive hydrologic environment, weight and handling considerations, local construction preferences, and the requirement to have a cavern design life of 50 years. FRP bolts with cement grout were ultimately chosen for the project. The FRP bolting system has proven to be very successful, with no ground failures experienced where systematic FRP bolting has been applied. This paper discusses the properties of FRP bolt/cement grout bolting systems, their characteristics in relation to steel bolt/resin bolting systems, and numerical modeling results assessing their performance.

Jan 1, 2014

By Thomas L. Vandergrift

The type and severity of coal mine entry failures are affected by the strength and stiffness properties of the roof, floor, end coal. Knowledge of the mine-wide trends of these properties Is valuable in developing effective ground control plans. Within the context of a larger effort to Improve entry stability In high horizontal stress fields, the U.S. Department of the Interior, Bureau of Mines, has evaluated three portable, on-site test devices to determine their suitability for identifying mine-wide physical property trends. The devices evaluated were the borehole shear tester, the Schmidt harmer, and the point load tester. Despite the lack of standardized data Interpretation procedures, each device provided useful on-site physical property data. The Schmidt homer was preferred for trend identification because of Its speed and simplicity. Schmidt hammer data were collected over a large area of an underground coal mine to compare calculated roof strength trends with a known geologic feature.

Jan 1, 1990

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By C. D. Peters

The Bureau of Mines has been researching remote sensing analysis of an underground coal mining area in Utah and computer-aided methods of defining ground control hazards in this mining area. As a result of these studies, a preliminary potential hazards map was developed for the test site. This map is based primarily upon a lineament (linear feature) analysis of Landsat satellite data. Other data used were paleochannel location data, resistivity data, and information from surface and underground field checking of the lineaments and ground control problems in the mine. Lineaments proved to be reliable indicators of hazardous areas, although the type and degree of hazard varies with different lineament trends and the presence of other conditions such as lineament intersections and intersections with other geologic structures or with paleochannels. Lineaments were observed to match faults, joints, and/or joint trends in the area. The paleochannel data, derived from drill hole data, provided basic information about potentially hazardous areas in the mine by suggesting where paleochannels could cause instability in the roof rock. The ground control problem data served largely to define the relative degree of hazard associated with lineaments and the types of hazards encountered in the mine. Resistivity data helped confirm the presence of fractures where they were expected to occur both from surface geology and from the lineament data.

Jan 1, 1986

By John Shepherd

Pillar extraction carried out using various methods (split and lift, Wongawilli and old Ben) involves the formation of narrow fenders (commonly 7 m of coal) formed by driving "splits" for lifting off with a continuous miner. The strata above a split and fender adjacent to the goaf consists of a cantilever beam (usually >3 m thick) that extends from the solid coal and bridges across the fender. Lifting off the fender from the split in safe conditions depends upon the bridging capability of the cantilever and the fender strength. The nature and competence of the immediate and near roof, the support capability of the coal fender and the presence of faults and or joints can adversely affect the bridging behaviour of the cantilever. Insufficient knowledge of these parameters can lead to extraction under dangerous conditions. Remnants of fenders ("stooks") also support the cantilever and their dimensions are critical to obtain regular caving and goaf falls. Stook area, goaf roof span and roof stand-up time after lifting can be related and only a relatively small increase in Btook area of 10-15 m2 can lead to a significantly increased stand-up time, especially under a massive roof. Such conditions strongly influence the redistribution of abutment stresses and can create increased outbye pillar loading. Based on detailed underground geotechnical investigations, it is concluded that strata caveability, roof cantilever behaviour, fender H:W ratio and remnant stook size are all critical parameters for successful and safe pillar extraction.

Jan 1, 1992

By Gabriel Esterhuizen

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip comer of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

Jan 1, 2004

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By Yang Li

For the study of overburden movement in longwall mining of shallow coal seams, most scholars merely consider the thickness of bedrock and top soils. In this paper, the overburden movement in longwall mining of shallow coal seams with thin top soils and key strata group was studied. By using numerical simulation, the development of fractures in the overburden was analyzed for different ratios of panel width to depth (W/D) and depth to mining height. The results show that the overburden movement changed with the variation of mining height, panel width and depth under the specific geological conditions. It also explain how different overburden disturbance structures, such as ?three zones? (caved, fractured, and continuous deformation zones), ?two zones?(caved and fractured zones) or ?steps-like collapse? are formed under different mining conditions. The results broaden the vision for research on overburden movement in longwall mining of shallow coal seams.

Jan 1, 2014

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By Brian E. Travis

Recent Developments in the utilization of polymer grid structures for Longwall Shield Recovery operations are discussed. Specifically: various Longwall screen designs and the numerous methods employed during installation. Also discussed is the role of polymer grid structures in head and tailgate mf and rib control and their role in controlling soft bottom often associated in shield recovery operations.

Jan 1, 1993