Search Documents

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By Andrew G. Martin

In 1991, Modular Mining Systems began marketing a Slope Monitoring System (SMS) now installed at twelve mines. The SMS uses automated wire line extensometers to monitor field conditions frequently. Every few minutes, the slope displacement values and current temperature are transmitted to a central computer via a packet radio telemetry system. The desktop workstation receiving the data continuously provides updated displays of active slope monitors and generates audible and visual alarms if movement exceeds user specified thresholds. The computer system also generates numerous graphs and reports for quick analysis of slope stability. This work describes the functionality of the SMS, details improvements to the SMS hardware and software developed for several clients, outlines different installation techniques needed for wall rock and spoil monitoring, and interprets slope movement data using illustrations of stable and unstable conditions.

Jan 1, 1996

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By B Whittaker

The paper examines the role of chain pillars in longwall mining layouts as used in several countries. The application of chain pillars in relation to their expected design role is discussed. An important feature is the specification of the pillar design to meet strata loading conditions as imposed by the mining and geological setting. The paper relates longwall width and chain pillar configurations to pillar size to satisfy anticipated loading and strength expectations. Laboratory work is referred to which examines criteria for pillar stability. Comments are made regarding the application of the findings presented in the paper, to different situations involving the use of chain pillars in longwall and shortwall mining systems.

Jan 1, 1987

By Anand Bhagwat

Surface control can prevent the falls of ground between primary roof support systems and rib support. Using existing industrial products, and adopting them for mining applications, has historically attained surface control in underground mining. However, the latest innovative solution, a revolutionary wire mesh product, is designed specifically for underground mining applications jointly by Bekaert and Orica. This knotted wire mesh, FlexKnot? 2500 and FlexKnot? 3500, uses smaller gauge, higher tensile strength wires, than a chain link fence or welded wire mesh. The higher tensile wire enables the mesh to achieve greater ultimate load-bearing capacity, with significantly lower overall weight. Test results, obtained at the National Institute for Occupational Safety & Health (NIOSH) Mine Roof Simulator facility, illustrate the comparisons of the new FlexKnot with traditional 8- and 10-gauge welded steel mesh. The FlexKnot is superior in deflection, load-bearing capacity, and stiffness?categories that are critical in achieving safer surface control. It also offers enhanced corrosion resistance because of the galvanized coating applied on the individual wires prior to the knotting process. Case studies from underground coal mine installations confirm that FlexKnot has the ability to significantly reduce installation cycle time and to minimize use and repetitive manual handling of individual mesh panels. An added advantage is the ability to supply FlexKnot in rolls for quick and easy handling for either rib or roof support application. When using rolls, the bolter can install the entire roll with one continuous forward motion, unlike the wasteful back and forth travel for mesh panel.

Jan 1, 2014

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury ? occurs during recovery operations, Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action,Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the ? interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: ? Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Abouzar Vakili

Longwall Top Coal Caving (LTCC), as the most attractive method for thick coal seams, has been suffering from insufficient geomechanical understanding for the past few years. Cavability without doubt is the most critical geomechanical issue associated with the top coal caving method. A discontinuum method has been used for comprehensive modeling of LTCC operation by using the Universal Distinct Element Code (UDEC). In addition Particle Flow Code (PFC) and Phase2 were used as support for the caving mechanics analysis. Although the previous researches of gravity flow in caving operations neglected the effect of continuous span expansion, it has been observed in this study that face advancement has a great impact on roof symmetrical behavior. The amount of symmetry fluctuates between different face distances. Horizontal displacement seems to be the best indication for roof symmetrical evaluations. Two critical caving conditions have been modeled and parameters such as horizontal displacement, caving angle and recovery rate have been compared thoroughly. Results show that unsymmetrical behavior on the roof is closely related to face stability.

Jan 1, 2007

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Yi Luo

In dealing with various subsidence cases, accurate predictions of mining induced subsidence are the basis for correct assessment of subsidence influences and subsequent mitigation efforts. There is a good demand for a reliable tool to perform the subsidence predictions and related tasks. A comprehensive and integrated subsidence prediction model, CISPM, developed by the senior authors in the later 1980?s and early 1990?s (Peng and Luo, 1992) is one of such tools. Built on solid mathematical models and calibrated by a large number of collected subsidence cases, CISPM provides a rich set of features needed in subsidence engineering and research works. Its reliability and usefulness have been proven by numerous field applications. This upgrade of CISPM will not only preserve its original features and reliability but also provide some new needed features and a more user-friendly working environment.

Jan 1, 2008

By E. C. Westman

Anomalous geologic or stress-induced conditions can create a hazardous working environment for underground miners. Seismic attenuation tomography provides a valuable tool for understanding static and dynamic conditions induced by mining. As a longwall shearer cuts coal, it generates seismic energy. As this energy travels through the rock mass it is attenuated in a manner proportional to the degree of fracturing of the rock mass. By calculating this attenuation at specific locations underground, the degree of fracturing of the rock mass, and hence the relative stress state or material properties can be inferred. The goal of this work has been to create a tool which can be easily used by the mining industry to obtain information about the distribution of stress concentrations or material properties across a broad area in advance of mining.

Jan 1, 1996

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006