Search Documents

By Francis S. Kendorski

INTRODUCTION Drift design problems in caving operations are a re¬sult of the geologic factors contributing to the overall success of the system, of the engineering factors dictated by economic and technical considerations, and of ore production practices. Combining these factors, a rational underground sup¬port system of rock reinforcement, light steel channel section or welded wire fabric, and shotcrete can be de¬signed based on rock fracturing, rock load, abutment loadings, ground movement, expected repair and desired flexibility. The design concept uses the effect achieved by restraining, reinforcing, and maintaining some of the intrinsic strength of the fractured rock mass composed of interlocked blocks of intact rock and rock fractures. Three different examples of drift support design in hypo¬thetical mines using the caving system are given. Caving is a system of underground mining where ore is extracted by means of gravity after the ore body is allowed to fail by removing support from underneath. The rock mass of the ore body fractures and flows ver¬tically downward to let gravity do as much work as pos¬sible. Caving differs from many other mining systems in that blasting is used only to initiate the rock mass failure by removing the rock supporting the ore but not to break the ore itself. The initial movement of the rock mass dur¬ing failure and the consequent crushing and grinding during the continued movement serve to reduce the ore to particles of a manageable size, with only limited sec¬ondary blasting necessary. The broken ore is extracted from the bottom of the failed rock mass through funnels of some sort pre-excavated in the rock. Ore extraction must continue or the swell of the broken rock will even¬tually fill the cavity and stop further rock mass failure and movement. The excellent general discussion on block caving in the SME Mining Engineering Handbook (Julin and Tobie, 1973) adequately covers the principles and application of this type of underground mining. Many rock mechanics aspects of block caving have been covered by others (McMahon and Kendrick, 1969; Swaisgood, et al., 1972; Mahtab and Dixon, 1975; King, 1946) and will not be reviewed further. Maintaining the stability of production drifts is one of the most troublesome problems plaguing the mine manager in a caving operation. Many factors contrib¬ute to drift support problems, and identifying the causes of instability and producing a reasonable support design are two steps toward achieving stability consistent with the mine plan. This chapter sets forth a technique for the design of support systems for production drifts in caving opera¬tions. The basic support system elements employed are rock reinforcement, welded wire fabric, and shotcrete. Recognized as contributing to the design are the factors of rock load, additional load from mining activity, rock fracture characteristics, repair expected, and flexibility. It must be emphasized that the drift must first be stabilized as for a tunnel, and the additional strengthen¬ing for mining-induced loads cannot contribute to the initial premining stabilization, or the reserve of strength is used up. MINE PLANNING The efficient mine planning engineer not only must satisfy the economic, human, and environmental aspects of his task but must also consider the mechanical con¬sequences of his plan. The problems created for the mine by placing parallel drifts too close, by crossing drifts on different levels with inadequate, if any, separa¬tion, and by installing connections and crossovers in the haulage plan without regard for the effective spans cre¬ated, are only a few of the problems a mine planning engineer can create for himself and the mine. The effect on immediately adjacent mine areas when an area is caved is important to drift design because the removal of vertical support from a rock mass causes the weight of that rock mass to be shifted elsewhere. The adjacent rock mass will carry this load and reach a new equilibrium with the applied stress. The advancing front of stress increase that results from caving (and many other mining systems) is generally called the abutment load and is the increase in stress over the gravity or tec¬tonic stress that already exists, as shown in Fig. 1. In general, the abutment load will be similar in nature to the stress change found around an opening in rock and will be taken as causing an increase in the vertical prin¬cipal stress, due to an approaching caving boundary, so that

Jan 1, 1982

By Betty L. Gibbs, Jean A. Arcamone

Introduction Microcomputers are becoming more convenient to use at all levels in the business world, including the mining industry. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective computer use to design underground workings combines the calculating power and speed of a computer with the technical expertise and judgment of an engineer. Computer programs can perform in minutes calculations that might take several months for an engineer. But the engineer must be on guard when using computers for calculations. It is easy to assume the results produced by a computer program are always correct. However, the computer is only a sophisticated calculator. It cannot recognize logical errors or transposition of numbers. Also, some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively. In this article, selected commercial programs are discussed. These programs can provide engineers with tools to evaluate engineering designs for underground mines. The programs perform much of the tedious calculation. The engineer, though, must still make decisions and conceptualize designs. The software mentioned in this article runs on microcomputers and minicomputers. The mention of particular software, however, does not imply endorsement. Mining projects After a decision has been made to proceed with an underground mining project, more detailed evaluation of the mining method and extraction sequence begins. If a mine is already in operation, schedules and plans are needed to more clearly define future production. Existing operations can benefit from identification of bottlenecks in material movement and produce extraction options to make the mine more efficient. Detailed studies for a new mine are based on the technical engineering design. These studies provide specific details to determine equipment requirements. Detailed studies done during a project are similar to short-term planning and control carried out daily by the mining engineers. The engineering design phase includes: • Study of the infrastructures - entries, shaft, access from surface to underground; • Definition of the mine layout, hydrogeology, geotechnical considerations, transport, and ventilation; • Choice of machines and equipment; • Mine scheduling, including waste extraction and production sequencing; and • Economics, including labor and supplies. Further detailed studies include: • Blasting patterns; • Detailed geotechnical calculations; • Secondary ventilation; and • Production cycles along with coordination of the workings. Objectives The primary objective of underground mine planning is moving material out of the mine at the least cost. Development of the production schedule considers location and volume of ore units, transport distance, equipment and manpower interactions, and grade or quality of material. Two methods can be used to determine the scheduled material removal: optimization or trial and error. The microcomputer programs discussed here do not cover optimization for underground mine planning. For several reasons, optimization is often a "black box" approach. Although optimization is possible with linear programming techniques, few mining operations can be described effectively with linear equations. An interactive trial-and-error approach is desirable because engineering judgment can be inserted as a plan develops. Because of the large number of factors in an underground operation, an optimization technique seldom covers all possibilities. Few of the programs available consider all of the possible parameters. The programs use an interactive sequencing or a simulation approach and are either event-oriented or deposit-oriented. The most desirable programs offer an integrated approach. They consider a broad range of operating conditions including equipment, labor, costs, material movement, timing, and mine layout, among other factors. The two types of models generally used in designing underground workings include: • The interactive model, which requires direct, incremental input from the user. Outlines of the section to be mined may show on the screen. The engineer causes the model to develop piece-by-piece. The program may offer feedback on parameters such as tons and grade, or other values, as the section is "mined." • The simulation model, which is usually an automatic technique. Parameters related to the process are entered. The program then calculates the mining sequence over a designated time period or until the economic material is exhausted. A simulation model imitates step-by-step performance of equipment or other processes.

Jan 3, 1988

Introduction Surface mining is a business, and the objective of most businesses is to make as much money as possible within certain responsible constraints. Businesses normally measure their potential to make money by estimating the discounted cash flow rate of return on new projects or the net present value for ongoing projects. These estimators of profitability are calculated using the following well-known equation: [ ] where i is the year, n is the total number of years, A, is the after tax net cash generation in year I, r is the discount rate and NPV is the net present value. In its simplest form, when the value of r makes the NPV equal to zero, the discounted cash flow-rate of return (DCF-ROR) is defined. The maximum economically recoverable reserve is identified at the point where the NPV or DCF-ROR is at a maximum. Depending on the measure used (DCF-ROR or discount rate) for calculating the NPV, the definition of recoverable reserve will be different for exactly the same deposit. Maximization of the measure of profitability and the economically recoverable reserves should not be separated from the mining method and sequence of exploiting the reserve. The surface mining methods may involve multiple-pass development of the resource, mining to the ultimate limit in one pass or a combination of the two methods with backfill. Multiple-pass development When planning a multiple-pass mining operation, it is important to determine the width of pit expansions that are appropriate for a specific situation. Production personnel typically want wide, open work areas where operations can be set up to run at peak efficiency. While this is understandable, the trade-off between highly efficient production operations and an overinvestment in stripping should be carefully weighed. As long as safety is not compromised, a few cents per bank cubic yard increase in operating cost due to lower productivity by working in more confined spaces may well be offset by a decrease in the overall short-term stripping requirements. A mini study on productivity and cost should help quantify this cost before deciding on minimum phasing requirements. The bigger challenge associated with establishing smaller work areas is securing operations and management buy-in to marginally lower productivity when reporting results. When cost reduction is the important management goal and everyone is focusing on unit costs, one sometimes loses sight of the goal of total cost management and, even more importantly, maximum profitability. The first pit should be defined by the first grouping of recoverable mineral that has the highest after-tax unit value and forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. 1 is constructed for a rate of production, R, and a quality management strategy, Q, by calculating the NPV for a series of sequences, with each sequence assuming that the operations are terminated on successively lower profit pits. These values are plotted to form the curve in Fig. 1. If the operation ceases on a pit that has too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have made more money invested at the discount rate than by mining the next pit expansion. Therefore, the maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV. There may be an opportunity to refine the definition of the "ultimate pit" around the maximum-value point. The precise definition of the ultimate pit early in the mine life may or may not be important today, depending on how far off in the future these limits will be reached. By the time an operation must decide on its last increment of economically recoverable reserve. much of the

Jan 1, 2000

Brace yourself-what used to be a 1 billion ton deposit is now a 1 Gt deposit. And that 1520-hp ball mill is now a 1.134-MW ball mill. Beginning with this issue, all engineering units and statistics in MINING ENGINEERING will be reported in SI units. The exception to this is the Technical Papers section, where units may still be reported by dual notation. For the past four years, ME has reported all units of measurement first in SI, followed in parentheses by the equivalent English value. This metrication policy, adopted by the SME-AIME Board of Directors in September 1975, was designed to aid magazine readers through a transitional period from English unit reporting to SI unit reporting. In October 1979, the SME-AIME Publications Board completed the English-to-SI transition by requesting the editorial staff, beginning February 1980, to report exclusively in SI. The Publications Board also requested the editors to prepare a chart of SI conversions useful to ME readers; this information follows on pages 156-157. The What and Wherefore of SI In 1960 the General Conference on Weights and Measures met in Sevres, France, and recommended that a new metric system-one that could uniformly cross all international borders-be adopted to replace all other metric systems. The outcome of this recommendation was the SI system of units, an abbreviation for le Systeme International d'Unites (the International System of Units). It replaces the more familiar cgs (centimeter-gram-second) system and the m/ksA (meter-kilogram-second-Ampere) system. SI consists of seven base units, two supplementary units, and a number of derived units. Other units, called allowable units, may be used even though they are not part of SI. The seven base units are: meter (length); second (time); kilogram (mass); mole (amount of substance); kelvin (temperature); ampere (electric current); and candela (luminous intensity). The two supplementary units are radian, a measurement of plane angle, and steradian, a measurement of solid angle. Supplementary units can be used in combination with SI units, e.g., radiant intensity is expressed in W/sr, watts per steradian. Derived units are combinations of base and supplementary units. Velocity is expressed as meters per second (m/s), and acceleration as m/s'. Using the relation established by Newton's second law of motion, force is expressed as kg-m/s2, more commonly known as the newton (N). Energy (work) is force times distance, expressed as kg-m/s2 and known as the joule (J). Power is work per unit time, expressed as kg, m2/s3 and known as the watt (W). Allowable units are the exception to the rule-they are not taken from base or supplementary units but, nevertheless, are used in the SI system. Volume units are normally expressed as the cubic measure of a length, such as cm 3. But a fluid volume of a cubic decimeter (dm3) is called a liter (L); the "L" is capitalized in another special SI rule to keep the lowercase "1" from being confused with a numeric "1". Other allowable units are degrees Celsius (°C) for temperature; and the minute (min), hour (h), day (d), and year (a) for time measurements. The prefixes in the table on the following page are used with SI units to express the magnitude of a measured quantity. A mill that processes 1000 tons of ore per day would be designated a 1 kt/d mill; a mine producing 10 million tons of ore per year would be called a 10 Mt/a mine. The rule here is to use prefixes that keep the value in a convenient range from 0.1 to 1000. In other words, it would be incorrect to write 25 000 kg-the prefix should be changed to indicate 25 Mt. One of the distinct advantages of SI is that it retains the decimal relation between multiples and submultiples of the base units for each physical quantity except for time. One more rule of SI syntax-numbers are separated into groups of three with a space between each group rather than a comma, e.g., 3,839,174 becomes 3 839 174. By the same token, a decimal number is also broken by spaces, e.g. 0.738153 is written as 0.738 153.

Jan 2, 1980

By S. Polegeg

The basic principle of this separation method was already defined in the middle of the nineteenth century. However, a change over for the treatment of minerals has followed from the construction of proper machines i.e. airjigs and airtables as late as in the twenties and thirties of this century. The main application of this technology was subsequently found in coal processing and reached quite a great dimension in the two following decades. The number of applications of this method in mineral dressing plants decreased rapidly and has almost vanished in the fifties in favour of wet concentration procedures. It has been for a long period as long as up to the eighties that no more consideration was taken for applying dry gravity separation in the field of mineral processing also due to the successful introduction of flotation. Due to the fact that labour cost was increasing remarkably within the past period after the end of World War II also the economic conditions in the agricultural sector became more though. As a result there came up a great demand for harvesting machines. Since agricultural products can only be processed by dry methods in a prevailing number, highly developed machines were introduced for the dry processing of food and feed stuff.

Jan 1, 1992

By K. J. Henderson

INTRODUCTION Shrinkage mining at Inco Ltd.'s Crean Hill mine can best be defined as a horizontal breasting method utilizing the broken ore for the mining floor and to provide wall support, with draw from a series of boxholes or draw¬points at the base of the stoping block. In choosing to shrink a given block of ore, the initial investigation centers on the ore configuration and grade, the expected ground conditions in the stoping area, the expected profit compared to alternative mining methods, the future production requirements, development lead time, the availability and type of equipment in the area, and the availability of experienced miners. These factors are weighed against other mining methods and shrinkage mining is chosen when the advantages outweigh the dis¬advantages. These will be discussed in more detail later. At Inco Ltd.'s Crean Hill mine, shrinkage mining makes up 17% of total mine production and is decreasing due to the advent of advanced blasthole techniques, notably in-the-hole drilling. Shrinkage is an adaptable mining method that is currently employed in narrow irregular ore zones, as undercuts for in-the-hole blast¬hole stopes, in ore bodies that do not extend from level to level, and in areas where quick production is required with a minimum of capital outlay or minimum develop¬ment. Two major types are currently in use which are classified on the basis of type of draw system employed. These are the utilization of load-haul-dump (LHD) equipment drawing from drawpoints, and the slusher and train method drawing from boxholes into a slusher trench and loading into a train. A third method being phased out is drawing from chutes directly into a train. In all three methods the actual stoping operation remains the same. In the initial planning of a mining block, the ore body is first located using an exploration diamond drill¬ing program. This is essentially done at a 130-m (400¬ft) spacing and it gives an indication of the amount of ore, grade of ore, the configuration of the ore body, as well as other geological features such as ground condi¬tions which will affect future mining. This drilling is done from an exploration drift 165 m (500 ft) long in the hanging wall and covers a vertical extent of 330 to 670 m (1000 to 2000 ft). However, these data are not accurate enough for detailed planning. When the de¬cision has been made to mine, a preliminary develop¬ment drill drift is driven in such a position that it can serve the dual purposes of allowing the ore body to be drilled off in detail, or of later serving as a haulage or access drift. Diamond drilling from this drift is usually on a 15-m (50-ft) grid spacing and gives adequate information for detailed planning. Utilizing the drill data, a decision is made on the mining type. For a shrinkage operation, the stoping block is ideally 49 m (150 ft) in length and a maximum of 13 m (40 ft) in width. Lengths of 65 m (200 ft) are considered a practical maximum because of the length of time the back of the stope remains open during the min¬ing of a cut. A minimum length of 13 m (40 ft) is used because the amount of time spent in opening a new cut increases in comparison with the total stoping time. The maximum width of 13 m (40 ft) is used because ex¬perience with the ground indicates that generally stope backs tend to be unstable over greater widths. However, widths of 33 m (100 ft) have been mined. A minimum width of 5 m (15 ft) is used to allow an effective draw, but in unusual cases, a width of 3 m (10 ft) has been mined successfully. The dip of the ore should not be less than 1.04 rad (60°). Angles flatter than this will not pull properly resulting in inefficient mining because of ore hang-ups on the footwall side of the stope and the need for large stagings on the hanging wall. In considering shrinkage, mining ground conditions play an important role. Strong shearing, cross faulting, or dikes are avoided. These usually cause dangerous mining conditions and an alternative safer mining method which will give adequate support to these adverse ground conditions is employed. Production requirements are taken into considera¬tion when planning a shrinkage mining program. In it¬self, shrinkage mining is capable of producing ore in a relatively short time with little capital development. If quick production is required, this method can produce ore rapidly as all that is required is that the draw system be completed and the miners with jacklegs and stopers produce a limited amount of ore. The obvious disadvan¬tage is that not all the ore broken can be pulled from the stope immediately. However, a mining horizon with sev¬eral shrinkage stopes in different stages of production can adequately maintain scheduled tonnage require¬ments, the cycle being stopes under development, stopes actively mining, and stopes completed and pulling. When the decision has been made to use shrinkage mining in a given block, the haulage and draw system is driven. The proximity of the orepass system dictates whether the system is to be a LHD operation or a slusher trench operation. If the orepass system is in close prox¬imity to the stoping block, LHD equipment is employed because of its ability to operate efficiently over short haulage distances. A long tram to the orepass usually dictates a slusher trench operation with haulage by train. Internal orepass systems are used effectively with LHD equipment with a load-out and retramming taking place on a lower horizon. In addition, stoping blocks in older areas of the mine are developed track because of the capital cost involved in converting an existing level to trackless mining. DRIFT DEVELOPMENT USING LHD EQUIPMENT The haulage drift for a draw system using LHD equipment is driven parallel to the ore body in the foot¬wall at a sufficient distance to allow an 11.5-m (35-ft) drawpoint to be driven into the ore (Fig. 1). The actual position of the drift depends entirely upon the ore con¬figuration and the drift size depends on the equipment to be used. Drift sizes of 4.6 x 4.1 m (14 x 121/2 ft) for an St-4 and 3.8 x 3.6 m (111/2 x 11 ft) for an St-2 meet company and government clearance standards and allow sufficient space to accommodate a ventilation pipe. The

Jan 1, 1982

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By William F. Riggs

The basic theme of this symposium and panel Is Rotation Pads: Are They Optimized? There Is a. reason for phrasing the title In the form of a question. There Is not only the technical competency which we must address; there Is the operating philosophy that must be evaluated on the part of both the customer and the supplier. Customers desire reagents which are trouble-free and capable of providing that extra amount of selectivity or recovery. When they receive ft, after the supplier has provided several years of Internal research, one of the first concerns/complaints Is the price of the product. This has a tendency to rapidly reduce a supplier's support level In the future. Suppliers are equally guilty from another perspective. When they approach a customer to Introduce a product, they often attempt to market by offering only a price Incentive. They then wonder why a customer doesn't respond Immediately to the incentive. They are often oblivious to the fact that the reagent cost is such a minor aspect of the operating budget, and the customer has many more pressing problems on a day-to-day basis In comparison to the reagent cost. We need to establish the understanding that reagent cost Is an Inconsequential cost of operation, and yet has such a disproportionately high Impact on the success of the entire operation. This understanding Is required by both the customer and the supplier. We say to each other,' why are we discussing this since this has been obvious for some time?' The reason is relatively simple in that we talk about it, acknowledge it, and yet we do not adhere to it. The supplier provides a product along with test data containing statistics, analysis, recovery, grade and cost calculations while most of the time ignoring the operating technique which must be applicable In the plant In order to optimize the product. He expects the reagent to be substituted In the plant for the existing reagent and ft works or does not work after trying several variables. The operating management Is equally guilty, In order to best explain this to both the customer and the supplier, ft becomes necessary to review the basic purpose of the major reagents utilized In flotation. A collector is basically to Impact selective, maximum water repellency on the surface of a particular mineral, The frother has the purpose of providing a chemically stabilized membrane on the surface of the bubble at the air-water interphase. This, then, provides a host environment for the attachment of the collector-coated mineral to a bubble. The depressant functions In the reverse of the collector and must demonstrate the same or greater degree of selectivity than expected of a collector. The key area which has been Ignored Is the rate by which these reactions occur and Interrelate. This has a very specific effect on the operating technique and the compatibility of the chemistry, equipment, and the operator himself. Researchers, suppliers, and customers provide reams of data to demonstrate how their products or design produce, for example, higher kinetics, more selectivity, or more recovery. The Information is often true. After all, we are all learned men and laboratory and actual plant data do not lie. However, we must remember the theme of this symposium and panel: Flotation Plants: Are They Optimized? and Optimizing of Flotation Reagents? The direct, honest comment to the two titles is very simple. OF COURSE THEY ARE NOT The plants, equipment, and reagents had better not be optimized or else we are in trouble. The Issue of this panel discussion is to approach this subject from a slightly different or perhaps mainly Ignored aspects of optimizing reagents in flotation. When we have reagents which provide higher kinetics, more selectivity, and better recovery, how do we use them? Since each reagent has a different physical characteristics of froth, rate of recovery, volume effect on the compatibility of equipment, and many more aspects too numerous to mention, the question which has been severely Ignored Is, 'What degree of study and cooperation by both the supplier and the operating management has been conducted In order to prepare the operator for maximizing the performance of a reagent In relation to the rest of the system?" Prior to testing a new reagent, how much time Is spent to bring the actual operator(s) Into the program to make them feel part of the program? How much time is spent explaining to the operator on the float floor how to possibly take advantage of a reagent with faster kinetics or one which Is Inherently more selective? What

Jan 1, 1993

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By Brett P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using alkali solutions1. Without implementing emission controls, world energy emissions will rise from 29.7 billion t in 2007 to 42.4 billion t in 2035. The first objective of the project was to determine the optimal amount of alkali in solution for CO2 absorption. This was accomplished using theoretical equilibrium calculations and experimental absorption data for alkali solutions of 1, 2, 3, 4 and 5 weight %. As the % alkali in solution increased, so, too, did the ionic strength of the solution. Theoretical calculations took into account the effect increasing ionic strength will have on the solubility of gaseous CO2. The calculations assumed negligible formation of H2CO3, constant temperature and constant pressure. In the experimental setup, a 16% CO2 /balance air gas mixture was bubbled through an Erlenmeyer flask filled with an alkali solution. The gas exiting the flask was fed to a gas analyzer to record the % CO2 in the exhaust gas stream. The % CO2 absorbed was taken as the % CO2 in the exhaust gas minus the % CO2 in the feed. Theoretical calculations found that as the % alkali in solution increases, the solubility of CO2 decreases. This was verified by experimental data, which found that a 2% alkali solution, by weight, was the ideal solution for CO2 absorption. Current research is focused on using the 2% alkali solution for permanent storage of CO2 via mineral carbonation to produce a value-added product.

May 1, 2012

By J. Singh

Recently, a Maryland bank became the overnight owner of a toxic waste site through a foreclosure. The original property owners had operated a crash and garbage business on the site and obtained loans for their business venture through the bank. In 1980, their son purchased the property from his parents with mortgage monies obtained from the bank. Failing to make his loan payments, the son defaulted on the mortgage. The bank foreclosed on the property and eventually purchased the property at a foreclosure sale. Shortly after the bank's purchase of the site, toxic wastes were found on the property--the result of disposing solid wastes on the site for 10 years. The bank declined responsibility for contaminating the site and consequently for its cleanup. The Environmental Protection Agency (EPA) took corrective actions to clean up the site. EPA then handed the bill to the bank, citing the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) of 1980 (more commonly known as "Superfund"). CERCLA imposes liability on the current owners and operators of hazardous waste sites.

Jan 1, 1988

By A. M. Edwards

In many ways a government could be regarded as a macro business enterprise. Its shareholders are its peoples, the productivity of the nation depends on them, and, indeed, the profits or losses of a nation's balance sheet can be linked to the surplus or deficit in its balance of payments. International loans need to be repaid, and in most developing nations the noose is tied so tightly that one wonders if such debts will ever be repaid. In their endeavour to meet such obligations, their currencies may be devalued [sometimes in frightening proportions], in the hope of boosting the export potential. However, this is a vicious circle, since exports will not be achievable unless sufficient technical expertise and infrastructure exist to address the opportunities which may have been created through devaluation. Many of the poorer countries have exportable resources of minerals, which are supplied on the international market. This may be the good news, but, unhappily, steps were seldom taken to enhance the value of the mineral products through further beneficiation and the production of high-value sophisticated products. That is where the vicious circle comes in: inadequate infrastructure is created, competent and well-trained manpower is not generated, and the result has inevitably been that the GDP slips backwards, and the nation becomes progressively impoverished. To exacerbate the problem, it is unfortunate that the more impoverished a nation becomes, the greater is its birthrate, and hence the greater the need to create wealth at the very time that the nation is becoming poorer and poorer. Within this scenario, one may well reflect that this is exactly what nations on the African Continent are experiencing, namely exploding populations, although most of the poorest nations in the world are found on this continent. Yet they often possess a superior mineral production potential. Africa still suffers from what may be called the colonial influence, in that the developed world has regarded this continent as a source of raw materials to feed its own factories. The colonial powers gave only secondary attention to developing the nation's peoples and its infrastructure, such as railways, roads, harbours, and other services. These problems all naturally fall within the ambit of government interest, and it is therefore obvious that the state should play a dominant role in addressing them. The reasons for governmental involvement in mineral-related research and development differ considerably, depending on the state of industrial development of that country. Thus, in the highly industrialised world, government's interest will lie mostly in the fields of strategic minerals, which may not be economically exploitable. An example would be the exploitation of American low-grade chromites during the Second World War, or minerals which need to be imported from unfriendly or unreliable sources, such that disruption would not be in the national interest. Colonial powers like the United Kingdom and France established R&D facilities to assist, inter alia, in the exploitation of mineral resources in their colonies. The approach of developing countries would differ from that of the industrialised nations, in that their primary quest would be to promote, support and encourage the development of infrastructure, and the establishment of major industries in order to create and provide employment opportunities, as well as to support small operators who cannot afford to undertake their own research and development. On the debit side, it is a sad fact that, however good their intentions may be, underdeveloped countries are invariably unable to provide the requisite financial support to sustain their own research-and-development laboratories. In a high-tech world, the cost of sophisticated equipment is steep and cannot be afforded. Again, the proverbial vicious circle comes into play. The competent researchers find themselves without rewarding employment and would therefore shun such institutions. Recent trends in the developed world have been to privatise research-and-development institutions, the argument being that they should draw closer to the industry they serve, and that the provision of taxpayers' money for strategic purposes is no longer as important as it may have been once. Complete state withdrawal has had its negative effect in that long-range, high-calibre research has tended to be replaced by short-term problem-solving projects. Industries engaged in the minerals business differ somewhat from major ones, like motor, computer or pharmaceutical industries, which are large enough to support their own internal research and development, and whose work is highly confidential, so that any leakage could have disastrous consequences. Furthermore, private companies are answerable to their shareholders and costly long-range, 'blue-sky' research would be difficult to justify. Since mineral research has become of lesser importance in the sophisticated First World, this trend has persisted. On the positive side, R&D institutions which are totally financed by government, suffer because they tend to forget the reason for their existence. They have often become a form of auxiliary to an academic institution where higher degrees are collected by scientific boffins who, in their quest for academic excellence, tend to disregard the benefits that industry may ultimately gain from this research endeavour. The trend in recent years - and South Africa is no exception - has been for the state to progressively reduce its subsidy, whilst at the same time encouraging research organisations [for their ongoing survival] to interact closely with industry, and to conduct work directly for them on a contract basis. Organisations such as CSIRO in Australia, CANMET in Canada, the USBM in the United States and Mintek in South Africa all generate income from the private sector. However, the critical fact is that the State should never withdraw

Jan 1, 1995

By A. M. Johnson

Although known primarily for native copper, the Keweenaw Peninsula of northern Michigan also has deposits of copper sulfide (chalcocite) ore. A number of small, but rich, deposits are present at relatively shallow depths near the base of a thick, steeply dipping sequence of volcanic and sedimentary rocks. Because much of the ore is fracture-controlled, the deposits appear to be ideal candidates for in-situ leaching. Fracture mapping from drill core and borehole logs coupled with borehole packer permeability tests are being applied to evaluate the suitability of the ore for in-situ leaching. A leaching scheme utilizing a bacterial-assisted ferric iron lixiviant is being tested at bench scale. A pilot scale test is being designed to evaluate the system in the field.

Jan 1, 1988

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth's surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex's findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

By M. G. Ayat, B. C. Scott

J. Dasher Having an interest in coal slurry pipelines from a decade of arguments with Ed Wasp and crew at Bechtel about pumping thicker slurries slower, I immediately read this article and found nothing in it pertinant to the title. Ayat and Scott pumped five unidentified coals at 9% solids (50%-60% is the area of interest) in a 25-mm (1-in.) pipe around two square elbows through a 76-mm (3-in.) cyclone for up to 60 minutes and sized a large number of samples of unstated size on an unidentified wet screening device. They did not measure power consumption, discharge pressure, flow rate, or give pump tip speed or impeller diameter. They siad the cyclone had a "high" pressure drop (unmeasured) and did much of the degradation (measured) but more or less per unit of energy expended? Hargrove was not measured, so there are no data as to whether it would correlate with degradation. The authors conclude, with no attempt, correlation is "hard to establish." Please experiment before concluding. I am at a loss to know what "increasingly smaller size" means, much less what theory says such particles take "exponentially larger quantities of energy," which the authors neglected to measure. If such experiments without pertinent data or justified conclusions must be published, please attach a pertinant title. reply by M. G. Ayat The first and the last criticism of this paper is that the work is not pertinent to the title. Anybody who reads this article will immediately realize that the work describes the breakage of coal particles to finer sizes in coal slurry pipes and pumps. If this is so, why not title the work "Degradation process in coal slurry pipelines"? What could be more pertinent to this title than the investigation concerning the degradation phenomenon of coal particles in a pipe carrying a coal slurry? Mr. Dasher complains that he does not understand the meaning of the term "increasingly smaller size." The first sentence of this article defines the degradation process as "the breakage of coal particles to increasingly finer sizes." The term "increasingly finer sizes" here means successive breakage of a fine particle to finer and finer sizes. According to Hukki (Hukki, 1975), the probability of breakage is high for large particles and rapidly diminished for fine sizes. We apologize for being brief about some of these definitions. The degradation process, breakage of particles to increasingly finer sizes, is so widespread in the mineral industry that we did not feel it necessary to bore the reader with lengthy definitions of some simple terms. Mr. Dasher states that the coals examined and their original size consist are unidentified. Please look at Table I and Table 2 in the paper again where you will find the original size consist of the coals examined and their full specifications. We only named the coals A, B, C, D, and E to avoid identifying the coal seams that were more susceptible to degradation. Not identifying the name of the wet screening device used in this work has also been criticized. In our opinion, wet screening operation is such a routine and standard procedure that naming the device by which the screening is performed would serve no purpose but to promote a sales approach. This was not our intention. We did not conclude that the correlation between the degradation process and Hardgrove Grindability Index is hard to establish as Mr. Dasher writes in his letter. We stated, not concluded, that "It is reasonable to assume that some relationship between the extent of degradation and its physical properties, such as Hardgrove Grindability Index, does exist. However, any definite correlation is difficult to establish." This statement is based on other researchers work, which are clearly referenced in the article. The conclusions of this paper were based solely on the findings of the experimental work. As for the theory of comminution that Mr. Dasher asks, we would like to refer him to some basic comminution books and articles where various theories are clearly described. For example, Hukki (Hukki, R.T.,"The Principles of Comminution; An Analytical Summary," Eng. Min. 176, 106, 1975) suggests that the relationship between energy and particle size is a composite form of three laws (Bond's law, Kick's law, and Rittinger's law). A comprehensive analysis of coal breakage processes is also performed by Broadbent and Callcott (S.R. Broadbent, and T.G. Callcott, "Coal Breakage Processes, I. - A New Analysis of Coal Breakage Processes;" and "Coal Breakage Processes, II. - A Matrix Representation of Breakage," Journal of the Institute of Fuel, pp. 524-539, December 1956). These and many other relevant publications explain the relationship between the particle size and energy much better that what can be said in this short reply. We will, however, agree with Mr. Dasher on one particular point. We, too, believe that if the investigation concerning the degradation process in coal slurry pipeline were to be pursued further, one could choose to determine one or more of the variables available in the process, such as discharge pressure, power consumption, percent solid, pipe diameter, etc.

Jan 1, 1989

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982

By Bob Snashall

"We could blow that damned fort out of existence if we could run a mine shaft under it!," claimed one Union soldier eyeing Bobby Lee's Petersburg defense line protecting Richmond and Jeff Davis. Puncture the line, take the hill behind, and the Confederate capital would celebrate Yankee jubilee, 1864. That was June. At 4:15 am, July 30, mine boss Henry Reese, sergeant, 48th Regiment, Pennsylvania Volunteers, gingerly entered the mine, dark and muddy. Something had gone wrong. The mine, set to go off at 3:30, hadn't exploded. It had to be checked. The main mine gallery, 1.5 m high x 1.4 m wide (5 x 4 ft) narrowing at the top to 0.6 m (2 ft), forced Reese into a tuck run. Some¬where up there in that 155 m (511 ft) stretch running 6 m (20 ft) under the rebel works, moisture may have doused the charge. Or maybe a fuse splice went awry. Or maybe there was live fire steaming like a locomo¬tive towards 3.6 t (4 st) of black powder. Perhaps now Reese wished this sprint was shorter. For the mine boasted a record break¬ing distance in military annals. Lieut. Col. Henry Pleasants Credit goes to Lieut. Col. Henry Pleas¬ants, commander of the 48th, who overheard the soldier's claim for what a mine could do. In peacetime, Pleasants had been a railroad engineer working on the Sand Patch Tunnel. He later switched to mining, working for the Philadelphia & Reading Coal & Iron Co. He even married the daughter of the editor of The Miners Journal. Grieving over his wife's early death, Pleasants plunged into the ven¬ture of war. This Union officer took the mine idea to the brass. Headquarters was less than enthu¬siastic. "The chief engineer of the Army and the rest of the regular Army wiseacres said it was not feasible," Pleasants wrote to his uncle. The pros scoffed, ticking off a list of horribles: No mine has ever gone that far, men will suffocate and be crushed, the rebs will countermine, the men will be trapped. Still, Pleasants eked out a signal to proceed. In the meantime, the miners of the 48th had commenced to dig anyway. It was like the 48th to proceed against the odds. The 48th Pennsylvania Volunteers The 48th had been recruited from Penn¬sylvania's Schuylkill County, anthracite coal mining country. The mines had been torn with strife over wages. Strikes and rioting were prevalent. Murder was not unknown. This "Buckshot" resistance centered in Pottsville, PA. It forced the governor to call in troops. Coal was in high demand to run the war machine. Pennsylvania operators worried that a military draft would stir up violence, closing the mines altogether and further shift¬ing business to emerging Illinois mines. Men lit out for the western gold fields in the tens of thousands. Secret societies bred in the mining camps invited draft agents to dance at the end of a rope. Jobs threatened by cheap, victorious South¬ern labor were one warning intended to get immigrant miners interested in the war. Operators gave miners time off to help de¬fend Philadelphia during Lee's thrust to Gettysburg. Even so, the draft spawned new violence and troop intercession. Soldiers were not welcome. The dust had barely settled when into this Pennsylvania "minefield" marched the 48th on a recruitment drive. The 48th had been in Lexington, KY on guard duty. When it came time for the regiment to pull out, the townspeople had prevailed upon authorities to extend the regiment's stay. Finally ordered to move out, the 48th was feted by a hanky-waving, tear-dropping send-off to the lyrical lament Auld Lang Syne. And Kentucky fancied itself to be rebel. Striding smartly into the Pennsylvania coalfields, the 48th attracted 400 recruits and marched off under regimental colors specially made by the proud citizens of none other than Pottsville, PA.

Jan 1, 1989

By R. Bruce Thorndycraft

Heap leaching should not be chosen for development of a property solely on the basis of paper studies. Management should be made to understand where the risks are in heap leaching, and management should be alerted to the variability of costs in heap leaching, many of which are based upon company philosophy. These concepts are complex, but easily illustrated with guided tours of existing heap leach facilities.

Jan 1, 1998

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992