Search Documents

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By Earl H. Miller

The United States Potash Company was the original discoverer and first producer of under-ground mined potash ore in North America and commenced active production of potash in 1931. In July 1956, the company merged with United States Borax & Chemical Corporation and is now a Division of that corporation. The mine is located twenty-two miles east of the city of Carlsbad and the refinery is located sixteen miles south of the mine, The mine was placed where the ore was found and the refinery placed where there was sufficient water for a dissolving and re-crystallization plant. For twenty-three of the last twenty-six years, the potash ore was mined with the room and pillar method, taking approximately sixty percent extraction and leaving forty percent in pillars. These pillars are generally fifty-eight feet by fifty-eight feet square. Three years ago, it was decided that removal of as large an extraction as possible from these pillars should be commenced.

Jan 1, 1958

By R. R. Odman

The Malmberget Division of LKAB is located 70 km north of the arctic circle and has about 2000 employees. The dominating products are sinter feed concentrate and pellets. A general flow sheet for the operation is shown in Figure 1. About 20 percent of the ore body consists of hematite, which is mined separately and processed into sinter feed concentrate. That pert of the ore consisting of magnetite passes through a dry cobbing plant. The robbing process includes crushing, screening and dry magnetic separation. The entire cobbing product is used as feed for the wet concentrator. After rod mill grinding and magnetic separation the concentrated slurry is classified. The coarse fraction (+200 mesh) becomes sinter feed concentrate and the slime fraction after further ball mill grinding and magnetic separation, becomes pelletizing feed. A small quantity of the magnetite ore is processed into special iron-rich products in the the wet concentrator. Two types of pelletizing plant are used, shaft furnace and straight grate. This paper will deal only with experience gained at the straight grate plant.

Jan 1, 1979

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By J. Fuchs

This paper describes the mechanized narrow vein cut-and-fill approach used for the Deep Copper orebody at Falconbridge Limited's Strathcona Mine. Strategies for achieving high productivity while maintaining ground stability at depth and controlling dilution are discussed, including the use of mini-electrohydraulic drilling equipment, containerized truck haulage, consolidated rockfill placement techniques, and a miners' incentive system.

Jan 1, 1992

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By Ernst P. Hall

The Irwin Basin. (Fig. 1)* is a synclinal or shoe-horn *Figure numbers throughout refer to color slides not included with the preprint shaped basin in the Pittsburgh Coal Seam, It is approximately 10 miles wide and 22 miles long at its maximum points. The surface of the land above the basin is hilly, rolling farmland,, typical of this area of Pennsylvania, and it is criss-crossed with streams and highways and liberally dotted with farm houses and communities. In-general the coal is pitched from north to south with a total drop of 610 feet'. The coal seam cross-section from east to west is bowl-shaped and rises as much as 375 feet from the low point of the bowl to-the-outcrop. Cross-sections showing coal elevations are shown on Figs, 4 and 50 Ground cover above the coal will vary from 0 to 550 feet, averaging about 350 feet throughout the area. This area is richly endowed with a history of coal mining. The first car of coal shipped cast of the Allegheny Mountains was mined in the Westmoreland Coal Company's Shady Grove (later North Side) Colliery in Irwin, Pa., early in 1853, This mine was opened in 1852 by Coleman, Hillman & Company. The coal was hauled from the mine to the freight station by horse-drawn wagon and. loaded into a then "standard" box car of 18,000-pound capacity. Coal mining in this region flourished and grew as steel production in nearby Pittsburgh demanded more and more of the high quality, metallurgical-grade coal of the region.

Jan 1, 1959

By R. J. Sweigard

The effects of postmining land use planning are addressed in this paper. These effects may include savings in reclamation costs and increased value of reclaimed land. However, this may result in greater planning costs and possible delays in production. Therefore, an economic analysis was undertaken in an effort to determine the importance of each potential result and to quantify the overall economic impact of postmining land use planning. A discounted cash flow analysis was performed using a surface mine cost model to analyze the sensitivity of selling price to changes in various postmining land use planning parameters. As a result of this analysis it was determined that the profitability of a project is most sensitive to delays in production, particularly, if the delay occurs after major investments have been made. Many methods have been proposed for evaluating postmining land use alternatives (Sweigard and Ramani, 1981). Both quantitative methods, such as benefit-cost analysis (Brock and Brooks, 1968), and nonquantitative methods have been proposed. The application of one specific analytical method is pursued in this paper.

Jan 1, 1985

By H. F. Anderson

The Palabora Mining Company Ltd. is probably best known for its production of copper since 1965. The success of the PMC mine lies in the outstanding technical and highly organized efficiencies applied to the massive mining, transportation, and treatment operations necessary to produce profitable copper. We are not however going to discuss the well-known copper operation but the extremely successful recovery and marketing of Baddeleyite by the PMC group. Let us first review the extraction process at the Heavy Minerals Plant. Non-magnetic ground ore from the copper magnetic separators is processed in the Heavy Minerals Plant for the extraction of the "heavy minerals" uranium and zirconia (Baddeleyite). Thorium is also present as a potentially recoverable mineral. The content of the minerals in the feed is probably the lowest in the world to be treated commercially. Minerals are separated from the waste ore by a gravity separation process in which the high density minerals segregate preferentially in a waterborne system.

Jan 1, 1985

By Alexander Pomerantsev

In recent years, bucketwheel excavators have found wide application in open pit surface mining not only because of their large production capacities, but also because they easily lend themselves to automation. Krupp, Orenstein & Koppel, Buckau-Wolf, Mechanical Excavator, Lauchhammer, Manufacturers in Eastern Europe designed and installed many models of bucketwheel excavators that can excavate any type of materials, could be used in any climate conditions and for any type of technological schemes in open pit surface mining, (Photo I, II and III)

Jan 1, 1979

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By Charles S. Robinson

The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains about 50 miles west of Denver. The ore body is being developed for mining by workings that extend more than 3500 feet below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson & Associates, Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentary rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past. Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreased with tire!. The rate of decrease in flow (or pressure) is exponential. By measuring the change in flow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 1, 1976

By Hal McVey

"Philosophy" addresses the definition and assigning of importance to the marketing of by-products. Two examples, one in metals and the other in industrial minerals, explore prime product to by-product relationships. Relative revenues from all products illustrate the importance of by-products to economic feasibility. "Mechanics" takes a broad view of the types of marketing organizations that are applicable to individual circumstances in the marketplace. In-house marketing as well as agents, merchants and trading companies are outlined and discussed. Philosophy Definition Of Terms Philosophy Definition Of Terms The definition of terns for a paper such as this is generally a necessary but not-very-interesting exercise. However, in simply trying to clearly define the term "by-product" some interesting relationships between products arise and the line of demarcation between "product" and "by-product" often becomes obscure. The search for that distinction represents the philosophy portion of the title. A couple of definitions of philosophy can even help to set the tone for what follows. According to Webster, philosophy is : 1 Pursuit of wisdom. 2. A search for a general understanding of values and reality.

Jan 1, 1983

By D. W. Scott

Ontario has a diverse industrial mineral resource base including abundant resources of structural industrial minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone and dolostone. These resources are used in the production of aggregates, brick, metallurgical stone, fillers, lime, cement and other construction materials. The majority of the operations are in deposits of Paleozoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were over 140 million metric tonnes of aggregates produced in 1985, approximately 115 million tonnes of which was produced in southern Ontario with the remainder being largely from Crown land in northern Ontario. The structural industrial minerals account for over 80% of the value of total industrial mineral production, with the remaining 20% of the value king accounted for by the non-structural minerals being led by salt which is produced in southwestern Ontario. A host of other non-structural industrial minerals are known but production is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite and by-product metallurgical sulphur products (Fig. 1). Location and Market Area Major production is in the area closest to the large markets of urbanized southern Ontario and the northeastern and north-central United States. In general, with the abundant variety and widespread resources of industrial minerals and the large population within 400 miles of most deposits, the market offers great potential. Ontario's 9 million population accounts for about 35% of the entire gross domestic product of Canada of $476.361 billion dollars in 1985. This equates to about 113 of the nation's buying power being within a 200 km (125 miles) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well developed industrial minerals industry fulfilling most of the structural industrial minerals demand in Ontario, as well as a subsidiary demand in neighbouring provinces and states.

Jan 1, 1987

By D. R. Hembree

This paper discusses the mineralogy and metallurgy of the Kuroko-style volcanogenic massive sulfide ores mined at Formosa Exploration Inc. I s Silver Butte Mine located in southwest Oregon. The principle ore type is pyrite + chalcopyrite + sphalerite, while subsidiary pyrite + bornite + sphalerite ore is also mined. The two styles of mineralization have distinctly different metallurgical behaviors and must be treated separately. Selective flotation methods are used to produce copper and zinc concentrates from the first ore type, while bulk concentrates are produced from the bornite ore. Careful mine planning and coordination between the mine and mill are utilized to achieve optimal recoveries.

Jan 1, 1993

By Calvin J. Konya

An investigation was performed to determine conditions which optimize fracture formation between blastholes used for purposes of pre-splitting. Experiments-involved high-speed photography in Plexiglas models and radiographs in sandstone models. Additionail data was obtained from full-scale pre-split blasts. Pre-split fractures between blastholes were found to form as a result of gas pressure and were affected little, if any, by stress wave interactions. Pre-splitting was effective with short period delays of 25 milliseconds or less, and did not require instantaneous initiation of blastholes. Significant reduction of ground vibration resulted with the use of delays

Jan 1, 1980

By William J. Wasko

Maintenance of mining equipment has become so complex and important from a cost and product ion standpoint that the organization must be set up in an engineering fashion to be successful. Production costs are greatly affected by proper maintenance. Tonnages can only be met when operating time is at its maximum and breakdown time is at its minimum. Last, but equally important, large capital expenditures must be protected and improved The effectiveness of the maintenance program will, in many respects, be a direct, result of the effort put torch in developing the overall program. Once the need of maintenance is realized, the next step is to determine what the organization should be and what it should accomplish. Follow through is then most vital. Preventing machine breakdowns and reducing maintenance costs are the primary goals of all maintenance organizations. Good preventive maintenance, a system for inspecting equipment and a complete record of inspections will help attain these goals.

Jan 1, 1966

By Dale K. Fields

With today's technological advances in mineral processing equipment, there is an increasing demand for accurate system control. This can only come about through representative sampling. The purpose of this paper is to guide you in the selection of sampling equipment and outline design parameters for the cutters used in dry and wet sampling without adding redundant mathematical probability formulas to your files. Special attention will also be given to the equipment used in conjunction with samplers and sampling systems, such as feeders, crushers, chutes, launders, and controls.

Jan 1, 1979